Tribology Commons^™

Characterization Of The Fatigue Threshold Behavior Of Uhmwpe, Bethany B. Smith, Anurag Roy, Robert O. Ritchie, Lisa A. Pruitt

Faculty Journal Articles

Ultra-high-molecular-weight-polyethylene (UHMWPE) has been the material of choice for bearings in total joint replacements (TJRs) for decades as a result of its excellent wear resistance, chemical inertness, energetic toughness, low friction, and biocompatibility. Utilization of this polymer in orthopedic devices requires oxidation, wear, and fatigue resistance. Balancing these important properties by tailoring processing techniques and modulating microstructural features has been an ongoing endeavor in the field. Research into the clinical applications of UHMWPE has primarily focused on the challenges of wear and oxidation while studies into the realm of fatigue have been more limited. Literature gaps exist in fully understanding …

Analysis Of Ptfe Radial Lip Seals For Wheel Bearing Applications, Madison Vogt

Theses and Dissertations--Mechanical and Aerospace Engineering

A numerical analysis was conducted to investigate the viscoelastic effects of nonlinear materials on the sealing zone and contact pressure distribution of radial lip seals in a conventional geometric topology. The use of nonlinear materials in radial lip seal applications is desirable to improve operation and reliability of rotating machinery due to their high operating temperatures, chemical compatibility, and low friction coefficients. Examples include, but are not limited to, seals within industrial air compressors, turbine engines, aircraft landing systems, chemical processing equipment, and Freon pumps. This work focuses on analyzing the nonlinear viscoelastic response of pure Polytetrafluoroethylene (PTFE) and PTFE …

Inherently Porous Metal Structures With Sufficient Mechanical Properties Through Direct Writing Of Bio-Based Inks, Havva Eda Aysal

Graduate Theses, Dissertations, and Problem Reports (ETD)

There is currently a burgeoning interest in developing 3D printed metal structures with inherent porosity and sufficient mechanical properties for mass customization in the biomedical field. Current approaches for 3D printing of biocompatible metals rely on powder-bed fusion methods which are energy intensive and utilize large amounts of metal powder that is challenging to recycle. In addition, such methods aim on producing dense parts and porosity generation, within the printed part, is challenging due to the complex physics of the melting pool. Here, a relatively new and promising approach is undertaken to study the 3D printing of inherently porous structures …

Tribological Studies Of Thick Polytetrafluoroethylene Coatings Enhanced By Polydopamine And Nanoparticles, Sujan Kumar Ghosh

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a popular low friction solid lubricant with high chemical and thermal stability. Thick PTFE coatings have the potential for many tribological applications, such as replacing Tin-based Babbitt materials in journal bearings. However, the weak bonding strength to the substrate and the high wear rate of PTFE coatings are current limiting factors. The lack of understanding of their tribological properties and wear mechanisms in oil-lubricated conditions and how coating thickness affects the tribological performance further hindered the use of PTFE coatings. In this dissertation, polydopamine (PDA), a bio-inspired adhesive, is used as an underlayer for or as a …

Viscoelasticity Of Ptfe-Based Face Seals, Bo Tan

Theses and Dissertations--Mechanical and Aerospace Engineering

PTFE-based materials are widely used in areas of tribology, particularly in seal and bearing applications because of their outstanding self-lubricating properties. Often in dynamic seal applications there is a need for ultra-low mechanical friction loss between the sealing surfaces. Due to its extremely low friction coefficient, there is interest in employing Polytetrafluoroethylene (PTFE) materials in such applications. One challenging aspect of employing PTFE is that these materials are viscoelastic and plastic. This dissertation concentrates on the modeling of viscoelastic material response when used as mechanical face seals with a focus on PTFE-based materials. First, the viscoelastic characteristics are measured through …

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Prediction Of Tribological Behavior Of Candidate Materials For Rotor Seals, John W. Franzino, Will F. Michul

Materials Engineering

To reduce high costs associated with manufacturing and testing materials for rotor seals, a procedure needs to be developed to quickly and accurately test candidate materials as they are released. The test should reduce the amount of fabrication required and model working conditions in order to accurately assess the tribological behavior of candidate materials. A possible solution was examined that utilized a rig meant to model operational stresses and wear. Compression modulus data was then taken in order to quantify the accumulation of damage due to microcracking, the primary mode of failure, through a damage index parameter. Testing results concluded …

Phase Transformation In Monolayer Molybdenum Disulphide With And Without Defects Under Tension Predicted By Atomistic Simulations, Khanh Quoc Dang

Graduate Theses and Dissertations

In addition to its use as a solid lubricant, molybdenum disulphide (MoS2) has gained recent attention as a possible substitute for silicon as it is increasingly difficult to keep shrinking down electronic devices made of silicon, the conventional electronic material. When thinned down to atomic thickness, monolayer MoS2 possesses very unique and promising electronic and electrical properties. Unlike electronic and electrical properties, knowledge of the mechanical properties and role of structural defects on these properties of monolayer MoS2 is unexplored. For this thesis, the two main objectives are (1) to gain insight about the failure mechanism of monolayer MoS2 by …

The Effects Of Machining On Structure And Tribological Properties Of Ultra High Molecular Weight Polyethylene For Artificial Joint Prostheses, Jinshan Song

Masters Theses

Understanding the effect of machining on the structure and property of subsurface layer of ultra high molecular weight polyethylene (UHMWPE) can significantly facilitate the increase in longevity of artificial joints. This study was performed to investigate the machining effects on the polymeric structure and tribological properties. Machining parameters include cutting speed, tool feed rate and depth of cut. Temperature rise was studied during machining to assess the extent of thermal degradation due to machining. Polymeric structure of the semicrystalline polymer was characterized using differential scanning calorimetry (DSC) in terms of melting enthalpy, crystallinity and melting temperature. Surface texture and hardness …

Mechanical And Tribological Properties Of Composites Of Recycled High Density Polyethylene And Recycled Rubber, Jason G. Boulanger

Masters Theses

This thesis presents a study on the mechanical and tribological properties of composite materials of recycled high density polyethylene (HDPE) and recycled rubber tire particles. The materials were compounded by extrusion and formed into test specimens by injection molding.

The first experiment studied the effect of recycled rubber percentage on mechanical properties of composites of recycled HDPE and recycled rubber. The mechanical properties included tensile strength, percent elongation, hardness, and impact resistance. Recycled rubber concentrations of 0, 5, 10, 15, 20, 25, and 30 percent were tested. The second experiment investigated the tribological properties of recycled HDPE and recycled rubber …