Other Mechanical Engineering Commons^™

The Collapsible Trailer: Design And Manufacture, Robert Hobson

Biomedical Engineering

No abstract provided.

In-Bottle Wine Aerator, Kevin Kesler, Patrick Lowry, Paul Woolworth

Mechanical Engineering

The proposal for Capitol Cultivators discusses and evaluates the development of an in-bottle wine aerator. It defines the problem and need for an aerator located inside the wine bottle. Additionally, it outlines requirements essential for an effective design and describes the engineering process that will be followed.

Trampoline And Bungee Fatigue-Test Machine, Andy Brock, Christopher D'Elia, Ryan Murphy

Mechanical Engineering

JumpSport, a Saratoga based recreational and fitness trampoline company, sponsored this senior project team towards the development of a fatigue-testing machine. The goal of this project was to iterate the previous machine JumpSport used for bungee cord, spring, and trampoline fatigue testing. Since minimal study had been conducted on these specific bungee cords, the fixture was designed to confirm the theoretical correlations for rubber and perform the final tests according to a strict protocol. Operating with a specific test protocol in mind will allow the data from multiple tests to be combined and analyzed statistically. With a design concept in …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Near-Infrared Surface-Enhanced Fluorescence Using Silver Nanoparticles In Solution, Michael D. Furtaw

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fluorescence spectroscopy is a widely used detection technology in many research and clinical assays. Further improvement to assay sensitivity may enable earlier diagnosis of disease, novel biomarker discovery, and ultimately, improved outcomes of clinical care along with reduction in costs. Near-infrared, surface-enhanced fluorescence (NIR-SEF) is a promising approach to improve assay sensitivity via simultaneous increase in signal with a reduction in background. This dissertation describes research conducted with the overall goal to determine the extent to which fluorescence in solution may be enhanced by altering specific variables involved in the formation of plasmonactive nanostructures of dye-labeled protein and silver nanoparticles …

Constant Voltage Hot-Wire Anemometry For The Boundary Layer Data System, Hon Yee Li

Master's Theses

To continue the development of the Boundary Layer Data System (BLDS), a constant voltage hot-wire anemometer (CVA) is implemented into the BLDS for flight-testing. The hot-wire anemometer was chosen as an alternative to the traditional pressure probe because of the ability to measure both average velocity and fluctuating velocity within the boundary layer. Previous work done on the benchtop has led to the design of miniaturization, flight-capable hardware for the BLDS. The next step in the development of the BLDS – CVA calls for quantifying the accuracy of the boundary layer measurements measured by the CVA system. To do this, …

Cae Methods On Vibration-Based Health Monitoring Of Power Transmission Systems, Brian Fang

Master's Theses

This thesis focuses on different methods to analyze power transmission systems with computer software to aid in detection of faulty or damaged systems. It is split into three sections. The first section involves utilizing finite element software to analyze gear stiffness and stresses. A quasi-static and dynamic analysis are done on two sets of fixed axis spur gears and a planetary gear system using ABAQUS to analyze the stress, strain and gear mesh stiffness variation. In the second section, the vibrational patterns produced by a simple bevel gear system are investigated by an experiment and by dynamic modeling in ADAMS. …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Ergonomichandle And Articulating Laparoscopictool, M. Susan Hallbeck, Dmitry Oleynikov, Kathryn Done, Tim Judkins, Allison Dimartino, Jonathan Morse, Lawton N. Verner

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention relates to a laparoscopic apparatus. The apparatus includes a handle having a body portion, a top surface, opposite bottom surface, a proximal and distal end. The top surface of the base is contoured to compliment the natural curve of the palm. The apparatus further includes a shaft projecting from the distal end of the handle. The shaft has a proximal and distal end. A control sphere is located on the handle. The control sphere can be moved by one or more of a user's fingers to indicate direction. An end effector is located at the distal end …

Scalar Differential Equation For Slowly-Varying Thickness-Shear Modes In At-Cut Quartz Resonators With Surface Impedance For Acoustic Wave Sensor Application, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

For time-harmonic motions, we generalize a 2-D scalar differential equation derived previously by Tiersten for slowly-varying thickness-shear vibrations of AT-cut quartz resonators. The purpose of the generalization is to include the effects of surface acoustic impedance from, e.g., mass layers or fluids for sensor applications. In addition to the variation of fields along the plate thickness, which is considered in the usual 1-D acoustic wave sensor models, the equation obtained also describes in-plane variations of the fields, and therefore can be used to study the vibrations of finite plate sensors with edge effects. The equation is compared with the theory …

Computer Simulation Study Of Slipper Lubrication In Hydraulic Machines, Jordyn B. Miller, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydraulic pumps and motors are vital components used in many applications today. Specifically, the axial piston pump is important because it is reliable, relatively compact, and has a high horsepower-to-weight ratio. These features make this type of pump very advantageous in hydraulic systems. Maintaining proper lubrication between surfaces in an axial pump, such as the slipper and swashplate, is imperative in order to have smooth operation of the system and prevent metal-to-metal contact. The aim of this research is to find the optimal slipper design and fluid film thickness to simultaneously maintain a balanced pressure and decrease power loss in …

A New Angle On Microscopic Suspension Feeders Near Boundaries, Rachel E. Pepper, Marcus Roper, Sangjin Ryu, Nobuyoshi Matsumoto, Moeto Nagai, Howard A. Stone

Department of Mechanical and Materials Engineering: Faculty Publications

Microscopic sessile suspension feeders are a critical component in aquatic ecosystems, acting as an intermediate trophic stage between bacteria and higher eukaryotic taxa. Because they live attached to boundaries, it has long been thought that recirculation of the feeding currents produced by sessile suspension feeders inhibits their ability to access fresh fluid. However, previous models for the feeding flows of these organisms assume that they feed by pushing fluid perpendicular to surfaces they live upon, whereas we observe that sessile suspension feeders often feed at an angle to these boundaries. Using experiments and calculations, we show that living suspension feeders …

Enhanced Reducibility And Conductivity Of Na/K-Doped Srti0.8Nb0.2O3, Guoliang Xiao, Sirikanda Nuansaeng, Lei Zhang, Suwit Suthirakun, Andreas Heyden, Hans-Conrad Zur Loye, Fanglin Chen

Faculty Publications

Donor and acceptor co-doped SrTiO₃ materials have shown interesting features in their conductivity and reducibility. In this work, 10 mol% Na⁺ or K⁺ as acceptor dopants have been introduced into the A-site of donor-doped strontium titanate, SrTi_0.8Nb_0.2O₃, and the doping impact on their properties has been studied. By doping with Na or K, the sinterability of SrTi_0.8Nb_0.2O₃ in reducing atmospheres has been improved. Na_0.1Sr_0.9Ti_0.8Nb_0.2O₃ and K_0.1Sr_0.9Ti_0.8Nb_0.2O₃ show metallic …

Flow-Induced Crystallization Of Isotactic Polypropylene And Random Polyethylene–Polypropylene Copolymers, Frederic Aubin

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Flow-induced crystallization (FIC) has been investigated for decades but the effect of molecular characteristics that hinder crystallization—such as the presence of random comonomers— on FIC remains scarcely explored. Flow greatly enhances crystallization kinetics and can induce the formation of highly oriented morphologies that affect final properties (i.e. stiffness, permeability, thermal conductivity, elastic modulus, etc.). Therefore, understanding FIC remains particularly important for developing predictive models to allow optimization of processing techniques involving flows.

Polypropylene represents ~ 40% of the global polyolefin production. The addition of ethylene comonomer allows their use as engineering plastics because of their particular toughness and flexibility. This …

Microphone-Based Pressure Diagnostics For Boundary Layer Transition, Spencer Everett Lillywhite

Master's Theses

An experimental investigation of the use low-cost microphones for unsteady total pressure measurement to detect transition from laminar to turbulent boundary layer flow has been conducted. Two small electret condenser microphones, the Knowles FG-23629 and the FG-23742, were used to measure the pressure fluctuations and considered for possible integration with an autonomous boundary layer measurement system. Procedures to determine the microphones’ maximum sound pressure levels and frequency response using an acoustic source provided by a speaker and a reference microphone. These studies showed that both microphones possess a very flat frequency response and that the max SPL of the FG-23629 …

Cisco Rackmount Bracket Optimization, Michael Baldwin, Edwin Lee, Garrett Smith

Mechanical Engineering

No abstract provided.

Rapid Decompression Containment System, Evan Domingue, Michelle Rudney, Daniel Trees

Mechanical Engineering

Cal Poly students; Evan Domingue, Michelle Rudney and Daniel Trees; are working with General Atomics Aeronautical Systems, Inc. (GA, ASI) and engineer John Wilcox to complete a senior project. The senior project is focused on finding a solution to meet the requirement set forth in MIL-HDBK 1791 4.2.5.2 for rapid decompression which requires cargo items to be designed with pressure relief devices or to be configured for air shipment as to prevent any part from becoming a projectile in the event of catastrophic loss of aircraft cabin pressure. The goal of this project is to design a safe, cost-effective, and …

Titan 130 Engine Aft-Mount, Woody Newell, Michael Haworth, Dylan Perry

Mechanical Engineering

No abstract provided.

Barbeque Grill Temperature Distribution Design Improvement, Peter Gobell, Connor Mcgill, Thomas Willson

Mechanical Engineering

Team License to Grill set out to asses Bull Outdoor Products, Inc.’s barbeques and quantify the apparent uneven temperature distribution or “hot spots” and “cold spots” across the grill. This testing was accomplished with the design and fabrication of a test fixture allowing for accurate and repeatable temperature collection across the barbeque. With results that matched the sponsor’s claims of hot and cold spots, an engineering model was made using heat transfer and thermodynamic equations. Once the model somewhat resembled the experimental data, it was used to suggest different modifications that would allow for better temperature distribution. It was discovered …

On-Demand Labeling, Nathan Cheadle, Lorne Stoops, Tony Wang, Robert Zimmerman

Mechanical Engineering

No abstract provided.

Mobybike Human Powered Hydrofoil, Steven Bieri, Tim Buckmaster, Kristen Heckman

Mechanical Engineering

The purpose of this project is to develop a human powered hydrofoil bicycle that uses the patented foil motion of the sponsor, Liquid Ideas, to generate lift and thrust to ride across the water. The bicycle will then be used to further develop and test the actuators that Liquid Ideas currently has. This report contains information from the concept design report on how the final design was chosen and detailed information on the final design, as well as plans for manufacturing, assembling, and testing the completed project.

High Temperature Filter Test Unit Upgrades, Blair Frandeen, Will Schill, Erick Shewmaker, Joshua Turgeon

Mechanical Engineering

The purpose of this project was to improve the existing High Temperature Filter Test Unit (HTTU) by optimizing performance and adding new features. These features include viewing ports and a camera system for observation of tests, a leak detection system, and a flame impingement system. Additional considerations included improving the current operation of the HTTU by reducing test time and energy loss. The HTTU is designed to test High Efficiency Particulate Air (HEPA) filters at temperatures up to 1300 ˚F, creating conditions which simulate a fire in a chemical processing facility. The HTTU was originally built as a Cal Poly …

Bicycle Wheel Test Machine, Dylan Harper, Kevin Hom, Ross Williams

Mechanical Engineering

In recent years, the cycling industry has witnessed huge advancements in bicycle components and materials. The age old goals of speed and low weight are still present today, but the pursuit of these goals may be reducing the structural stability of various components integral to wheel performance, including the wheel hub bearings. These bearings are invaluable to bicycles but little is known about how the forces and loads applied to a bicycle affect the performance of these bearings. Broken axles and hubs are indicators of significant stresses within the hub, but little is known about how the resulting deformation affects …

Autonomous Collision Avoidance, Thomas Stevens, Elliot Carlson, Ian Painter

Mechanical Engineering

A steering controlled, autonomous collision avoidance system has been developed by California Polytechnic State University. This system represents a step in the direction of fully autonomous driving, while allowing the driver to maintain control of the vehicle during normal driving conditions. In the case of an imminent collision, the system removes control of the vehicle from the user and autonomously steers around the obstacles. The final system is able to avoid two static obstacles with a 95% pass rate and one moving obstacle with a 50% pass rate. With full scale, fleet wide, implementation of this system it is expected …

Stent Graft Blush, Vanessa Barrett, Thomas Matzinger, Mike Morelli

Mechanical Engineering

In order to better understand Type IV endoleaks (“blush”), the Cal Poly Senior Project team GraftTest has developed a blush evaluation system able to mimic several of the aorta’s environmental parameters. Capable of both pressure and flow rate control, this bench top system accommodates Medtronic’s wide range of abdominal and thoracic aortic stent grafts. Having researched endoleaks, stent grafts, and numerous other factors affecting stent graft blush, a system was developed with the aim of assessing and comparing the performance of Medtronic’s stent grafts with regard to blush. Furthermore, this system has been designed to provide reliable and repeatable results …

Residential Fire Sprinkler Design For The Phi Kappa Psi Fraternity House, Nolan Frost

BioResource and Agricultural Engineering

This senior project discusses the design of a residential fire sprinkler system for a local fraternity house. The design follows NFPA 13D code, and contains design calculations, design drawings, material specifications, and cost analysis. The design was completed with the intention of being used for the installation of a fire sprinkler system in the house.

Adaptive Eating Device, Patrick Yale, Jillian Hiu, Jeremy Black, Kevin Farmer

Mechanical Engineering

No abstract provided.

Cal Poly Brocade Challenge 2013, Chandler Morehardt, Alexa Coburn, Juan Silva, Kerry Sun, Greg Wang, Raul Chagoya, Jd Torres

Architectural Engineering

No abstract provided.