Ocean Engineering Commons^™

Feasible Form Parameter Design Of Complex Ship Hull Form Geometry, Thomas L. Mcculloch

LSU New Orleans Theses and Dissertations

This thesis introduces a new methodology for robust form parameter design of complex hull form geometry via constraint programming, automatic differentiation, interval arithmetic, and truncated hierarchical B- splines. To date, there has been no clearly stated methodology for assuring consistency of general (equality and inequality) constraints across an entire geometric form parameter ship hull design space. In contrast, the method to be given here can be used to produce guaranteed narrowing of the design space, such that infeasible portions are eliminated. Furthermore, we can guarantee that any set of form parameters generated by our method will be self consistent. It …

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Ascorbic Acid Degradation In Cut Lemon Packaged Using Oxygen Scavenging Active Film During Storage, Kurniawan Yuniarto, Setyo Purwanto, Bruce Ari Welt, Anang Lastriyanto

Makara Journal of Technology

Oxygen scavenging active film can be used to prevent diffusion of free oxygen due to the action of permeation mechanism. In this study, biodegradable oxygen scavenging plastic film was designed by incorporating an antioxidant agent into plasticized polylactic acid or PLA-PEG (PPLA). Butylated hydroxytoluene (BHT) was added at different concentrations into the matrix of the PPLA film using a direct casting method to produce oxygen scavenging active film. The antiradical activity of the oxygen scavenging active film was observed, which could be applied for preventing vitamin C degradation in cut lemon during storage. The antiradical activity of the active film …

Development, Testing, Analysis, And Efficiency Of A Variable Area Dredge In Combination With A Mobile Ferrate-Based Treatment Facility, Leigh Ann Provost

Theses and Dissertations

This thesis proposal outlines the development and testing of a mobile slurry treatment trailer coupled with a variable area suction head and further expands on results and procedures shown in Feasibility of Muck Removal in the IRL Watershed and Subsequent Ferrate Treatment to Remove Excess Nutrients. The purpose of this thesis is to evaluate the efficiency and effectiveness of the suction head based on the percent solids maintained during dredging. This thesis also evaluates a scaled design and associated costs for a fully scaled dredging project utilizing the suction head. Additional statistics involving further fitting sediment data to a Weibull …

The Corrosion And Biofouling Characteristics Of Sealed Vs. Perforated Offshore Monopile Interiors: Experiment Design Comparing Corrosion And Environment Inside Steel Pipe, Monica M. Maher

Theses and Dissertations

This research addresses the need to improve on the existing methods for the corrosion control of the monopile interiors used to support wind powered turbines by incorporating a design that also enhances marine habitats and fisheries. Retrofitting monopile interiors with cathodic protection has been attempted on existing windfarms to mitigate corrosion, however, this can cause new problems including water acidification and hydrogen sulfide formation. Such chemistry changes can lead to unique localized corrosion concerns. This study investigated internal corrosion, chemistry and biofouling inside partially submerged hollow steel pipes. Watertight pipes with stagnant water inside were compared to pipes with holes …

Hydrodynamics Of An Anguilliform Swimming Motion Using Morison’S Equation, Naga Sasi Devarakonda

LSU New Orleans Theses and Dissertations

In this study, the hydrodynamic performance of anguilliform swimming motion is computed using Morison’s equation. This method was shown to predict the servo motor torques well. The anguilliform swimming motion is sinusoidal with increasing amplitude from head to tail. A “wakeless” swimming motion proposed by Vorus and Taravella (2011) with zero net circulation is considered.

This method is compared to the existing slender body theory and is validated with reference to the experimental results of NEELBOT-1.1 (Potts, 2015). The results for the study indicates that self-propulsion speed of the motion is independent of the oscillating tail amplitude at a constant …

Internet Traffic Forecasting Model Using Self Organizing Map And Support Vector Regression Method, Enrico Laoh, Fakhrul Agustriwan, Chyntia Megawati, Isti Surjandari

Makara Journal of Technology

Internet traffic forecasting is one of important aspect in order to fulfill the customer demand. So, the service quality of internet service provider (ISP) can be maintained at the good level. In this study self-organizing map (SOM) and support vector regression (SVR) algorithm are used as forecasting method. SOM is first used to decompose the whole historical data of traffic internet into clusters, while SVR is used to build a forecasting model in each cluster. This method is used to forecast ISPs traffic internet in Jakarta and surrounding areas. The result of this study shows that SOM-SVR method gives more …

Investigation Of Ship Hull Girder Strength With Grounding Damage, Muhammad Zubair Muis Alie, Ristiyanto Adiputra

Makara Journal of Technology

The objective of the present study is to investigate ship hull girder strength as a result of grounding damage upon longitudinal bending. A bulk carrier and tanker are analyzed and Smith’s Method is adopted and implemented in the analysis program. An efficient solution procedure is performed by assuming the cross-section remains plane and the vertical bending moment is applied to the cross section. As a fundamental case, the damage is simply created by removing the elements from the cross section. Welding residual stress, initial imperfections, and crack extensions are not considered. The grounding damage is made by two conditions, namely …

Effects Of The Preheating Temperature On The Crystal Structure And Texture Of Martensitic Stainless Steel, Tri Hardi Priyanto, Rifai Muslih, Herry Mugirahardjo, Bharoto Bharoto, Andon Insani, Muzzakiy Muzzakiy

Makara Journal of Technology

Theoretically, the preheating temperature refers to the start martensite temperature (Ms), and the martensite transformation can be considered as the conservation of the invariant habit-plane in the lattice structure. The habit-plane is the interface plane between austenite and martensite as measured on a macroscopic scale. From the calculation, Ms = 252 °C. The martensite formation can be affected by temperature or stress treatment. In this experiment, temperature treatment was conducted. The sample was treated at 250 °C ± 10 °C. Before and after the pre-heat treatment, the sample was characterized using the neutron diffraction method. BATAN’s Texture Diffractometer (DN2) with …

Satellite-Based Monitoring Of Spatiotemporal Changes In Batudulang Forest In Sumbawa, Indonesia, Mohammad Muslim, Arief Budhi Witarto, Wahyu Indrajaya

Makara Journal of Technology

Space-based earth observation technology applicable to forest inventory and monitoring is well known in the scientific community. High-resolution satellite images form an important data source for forest mapping and change detection at regional and national scales. The value of forest change information derived from remote sensing data is significantly enhanced if this information is integrated into a spatially explicit geographic information system. Satellite-based rapid assessment was conducted to measure spatiotemporal changes in Batudulang forest over the years. The general approach to quantify change in the spatial aspect of the forest involved change detection using moderate-resolution imaging spectro-radiometer satellite-based normalized difference …

Benchmarking Product Service System Of Generator Set Distributors, Venny Violetta Tiurindah, Tanika Dewi Sofianti

Makara Journal of Technology

Power generation is an industry that is essential to sustain daily life and competes with generator set distributors. The product service system of distributors must be improved to survive the competition. This research aims to develop tools for benchmarking the product service system of generator set distributors. Benchmarking identifies gaps between a product and other competitors’ products. In this work, a product service system board is used to visualize the current product service system of a generator set distributor. A PPIAF framework and a SERVQUAL framework are adapted to assess product performance and service quality, respectively. AHP is used as …

Strength Structure Analysis Of Main Gate Graving Dock Using Pontoons For Condition Repairs, Budianto Budianto

Makara Journal of Technology

Main gate graving dock with pontoon type can certainly suffered some level of damage after a long period of operation. Many employments within the graving dock can delay the process repair of main gate. The main gate may not be opened, because employees are still working to ship fabrication process under sea waterline. For accommodate these interrelated conditions, the best solution with repair one side of the main gate with type pontoon and employees can still work ship fabrication process in graving dock conducted simultaneously. The repair process conditions must be required main gate structure that consists of only one …

Microstructures And Hardness Of Tig Welded Experimental 57fe15cr25ni Steel, Parikin Parikin, Mohammad Dani, Abu Khalid Rivai, Agus Hadi Ismoyo, Riza Iskandar, Arbi Dimyati

Makara Journal of Technology

The microstructures and hardness of tungsten inert gas (TIG) welded experimental 57Fe15Cr25Ni steel were investigated through optical–scanning electron microscopy analyses and with a hardness tester, respectively. The welding process restructured the constituent atoms into regular and irregular crystal lattices. Rapid cooling of the weld metal allowed the formation of a dendritic (columnar) structure, with porous grains. By contrast, slow cooling influenced HAZ and led to the formation of grain structures. The crystal lattice became more organized and larger than other zones. Meanwhile, the base metal formed circular nets that covered large area inside thick and thin grain boundaries. The diffraction …

Mapping Of Bruise Of Oil Palm Fresh Fruit Bunch During Loading And Transportation From Field To Mill, Andreas Wahyu Krisdiarto

Makara Journal of Technology

Fresh fruit bunches (FFBs) are used as raw materials for palm oil, and their transport from a field is a critical step to maintain their quality. Fruit integrity should be maintained so the mill can efficiently obtain palm oil with less than 5% free fatty acid content. Physical treatments for FFBs during loading to truck bins and transport may cause physical injuries. This research aimed to map fruit bruises. The map can be used as a basis in managing transport of FFBs. Physical injuries were assessed by bruise index (BI), which was calculated by measuring the bruise area and weight …

Improving Seaglider Efficiency: An Analysis Of Wing Shapes, Hull Morphologies, And Propulsion Methods, Christopher James Hockley

Doctoral Dissertations and Master's Theses

Autonomous underwater gliders are a family of autonomous underwater vehicles used for long-term observation of oceanic environments. These gliders leverage changes in buoyancy and the resulting vertical motion, to generate forward locomotion via hydrodynamic surfaces. In order to function for extended periods, these systems operate in a low-speed, low-drag regime. This research examines factors impacting the operational efficiencies of gliders, including morphological changes, configuration changes, and propulsion. An interesting question arises when considering the operational efficiencies of conventionally propelled systems at the operating speeds typical of gliders. Can a conventional propulsion system match the efficiency of an underwater glider buoyancy …

A Quantitative Analysis Of Shape Characteristics Of Marine Snow Particles With Interactive Visualization: Validation Of Assumptions In Coagulation Models, Palak P. Dave

USF Tampa Graduate Theses and Dissertations

The Deepwater Horizon oil spill that started on April 20, 2010, in the Gulf of Mexico was the largest marine oil spill in the history of the petroleum industry. There was an unexpected and prolonged sedimentation event of oil-associated marine snow to the seafloor due to the oil spill. The sedimentation event occurred because of the coagulation process among oil associated marine particles. Marine scientists are developing models for the coagulation process of marine particles and oil, in order to estimate the amount of oil that may reach the seafloor along with marine particles. These models, used certain assumptions regarding …

Purple Urchin Removal, Cullen Goss, Wil Gilbreath, Kevin Marshall

Mechanical Engineering

Soaring purple urchin populations have contributed to a greater than 90% reduction of northern California’s bull kelp forests. Human intervention to reduce the purple urchin population may allow localized kelp patches to grow. The California Department of Fish and Wildlife requested that our team develop a mechanical device to aid in the removal of the urchins. This document provides an update from the scope of work and details the process conducted to reach a scale final design. In this document, we provide background research to show our understanding of urchins and their effect on kelp forests. Then, we analyze the …

Risk Assessment Of Dropped Cylindrical Objects In Offshore Operations, Adelina Steven

LSU New Orleans Theses and Dissertations

Dropped object are defined as any object that fall under its own weight from a previously static position or fell due to an applied force from equipment or a moving object. It is among the top ten causes of injuries and fatality in oil and gas industry. To solve this problem, several in-house tools and guidelines is developed over time to assess the risk of dropped objects on the sub-sea structures. This thesis focuses on compiling and comparing those methods in hope to improve the recommended practices available in the market. A simple modification is done on the in-house tools …

An Underwater Vehicle Navigation System Using Acoustic And Inertial Sensors, Khalid M. Alzahrani

Doctoral Dissertations and Master's Theses

Unmanned Underwater Vehicles (UUVs) have become an essential tool for different underwater tasks. Compared with other unmanned systems, the navigation and localization for UUVs are particularly challenging due to the unavailability of Global Positioning System (GPS) signals underwater and the complexity of the unstable environment. Alternative methods such as acoustic positioning systems, Inertial Navigation Systems (INS), and the geophysical navigation approach are used for UUV navigation. Acoustic positioning systems utilize the characteristics of acoustic signals that have a lower absorption rate and a more extended propagation distance than electromagnetic signals underwater. The significant disadvantage of the INS is the “drift,” …

Cfd Analysis Of Resistance For Stepless And Stepped Planing Hulls, Bhanu Prakash Valtheru

Theses and Dissertations

It is the endeavour of naval architects to design hull forms with the least amount of power consumption. In this respect, Naval Architects have been obsessed with the design of various hull forms optimized for a particular service requiring the lowest amount of fuel consumption keeping in mind effects on the climate change and sustainability. Regardless of the way that a considerable measure of research has been done around this area, there remains a level of uncertainty in the reasonably accurate resistance prediction of stepped hull forms in the early design stage. Model tests and full-scale tests are still the …

Hawai'i Wildlife Fund V. County Of Maui, Lowell J. Chandler

Public Land & Resources Law Review

In Hawai’i Wildlife Fund v. County of Maui, the Ninth Circuit held that the plain language of the Clean Water Act provides jurisdiction over indirect discharges of pollutants from a point source into groundwater that is shown to be connected to navigable waters. The court found that studies confirmed pollutants entering the Pacific Ocean were fairly traceable to the County of Maui’s sewage disposal wells. In affirming the district court’s ruling, the Ninth Circuit held that Maui County violated the Clean Water Act by discharging pollutants into a navigable water without the required permit. The court also concluded the …

Structural And Photoluminescence Properties Of Zno Thin Films Deposited By Ultrasonic Spray Pyrolysis, Iwan Sugihartono, Erfan Handoko, Vivi Fauzia, Artoto Arkundato, Lara Permata Sari

Makara Journal of Technology

Zinc oxide (ZnO) thin films on a silicon (Si) (111) substrate were grown herein using ultrasonic spray pyrolysis at 450 °C with different Zn concentrations. The ZnO thin films had X-ray diffraction patterns of a polycrystalline hexagonal wurtzite structure. The (002) and (101) peak intensities changed under different Zn concentrations. Furthermore, according to Scherer's and Stokes–Wilson equations, the crystallite size and the internal strain of the ZnO thin films in the (002) and (101) peaks changed with the Zn concentration. Optically, the photoluminescence spectra indicated that the ratio of the UV/GB emission of the ZnO thin films was the highest …

Coax-Fed Dipole-Type Applicator For Hepatic Cancer Rf Ablation, Basari Basari, Aditya Rakhmadi, Kazuyuki Saito

Makara Journal of Technology

Cancer is the third leading cause of mortality in the world and is one of the most difficult diseases to detect and cure. This fact motivates us to investigate a treatment method by using radiofrequency (RF) ablation. RF ablation therapy kills cancer cells by electromagnetically heating them up. The treatment uses an applicator that is inserted into the body to heat the cells. The cancer cells are exposed to a temperature of more than 60 °C in short duration (a few seconds to a few minutes), thereby causing cell destruction locally. To ensure effective treatment, a minimally invasive method is …

An Exploratory Study Of Sukuk Utilisation For Transportation Infrastructure Development In Indonesia, Fiona Lamari, Ayomi Dita Rarasati, Meilia Evita

Makara Journal of Technology

Investment in infrastructure is one of the principal drivers of the growth of the economy. For that reason, the Indonesian government has proposed an investment budget in the railway and sea and air transport sectors over the next 10 years. In order to overcome the burden of direct outflows and for the future, a study was conducted to lay down the framework of Shariah-compliant payments for the development of infrastructure in Indonesia in the transport sector. This paper aims to explore the opportunity and implementation of sukuk utilisation to develop transportation infrastructure. Secondary data study and interviews were selected for …