Ocean Engineering Commons^™

Power At Sea Develop Phase, Jake Lauer, Isabella Heinemann, Bailey Gargasz, Zachery Boyer

Mechanical Engineering

This project develops a renewable, wave-powered charging system designed to extend the mission duration of Autonomous Underwater Vehicles by eliminating the need for frequent manual battery replacement. Building upon a prior oscillating water column prototype from the CONCEPT phase, the team redesigned and tested an improved system capable of converting wave-induced air motion into electrical power using a Wells turbine. Key enhancements include doubling the column diameter to increase displaced air volume, integrating a flared inlet and bi-directional nozzle to improve airflow, and selecting corrosion-resistant materials suitable for long-term deployment in marine environments. Multiple prototypes were constructed and evaluated through …

Off-Grid Cabin Hydroelectric Generator, Keller Feltman, Lance Savatgy, River Perino, Jesse Valencia

Mechanical Engineering

This project developed a portable hydroelectric generator intended to provide low-power electricity generation for an off-grid cabin in Alpine County, California. The system was designed to utilize naturally occurring creek flow to generate electrical power while remaining portable, durable, and environmentally conscious.

The final system consists of an axial-flow turbine, belt-driven generator subsystem, waterproof electronics enclosure, aluminum support frame, and integrated wildlife protection screening. Engineering analysis was performed to estimate hydraulic power availability, turbine performance, drivetrain requirements, and component lifespan. These analyses guided the selection and development of the final design.

Throughout prototype testing, several design modifications were required. Initial …

Analytical And Data-Driven Modeling And Control Of Nonlinear Point Absorber Wave Energy Converters With Application To Cone–Cone Buoy Geometries, Houssein Yassin

Dissertations, Master's Theses and Master's Reports

This dissertation develops analytical modeling, numerical simulation, experimental validation, and data driven control methods for nonlinear point absorber wave energy converters, with particular emphasis on cone--cone buoy geometries. Geometry dependent nonlinear force models are first derived using pressure field and displaced volume formulations. These models show how buoy geometry produces nonlinear Froude--Krylov and restoring forces, including the dominant cubic behavior of cone--cone geometries.

The derived models are incorporated into a feedback linearization framework that compensates selected nonlinear dynamics while retaining the incident wave terms. An analytical optimal control formulation is also developed to maximize harvested energy in nonlinear, nonautonomous systems …

Design Of A 10-Ton Capacity Solar-Powered Cold Storage At The Cituis Fish Auction Site, Tangerang, Banten, Indonesia, Wardi Wardi, Muhammad Arif Budiyanto

Journal of Materials Exploration and Findings

This study presents the design of a 10-ton capacity solar-powered cold storage system for the Cituis Fish Auction Site (TPI) in Tangerang, Indonesia, as a sustainable solution to support the coastal fisheries sector. The system comprises two temperature zones: an anteroom at 5°C and a freezer room at -30°C, both integrated with a hybrid system utilizing solar panels and batteries. The total power consumption of the cooling system reaches 27.51 kW. The simulation results, obtained using HOMER Pro software, indicate that the hybrid PV system can reduce CO₂ emissions by up to 16,754 kg per year. From an economic …

Design And Implementation Of An Inverted Short Baseline Acoustic Positioning System, Jakob Frabosilio

Master's Theses

This document details the design, implementation, testing, and analysis of an inverted short baseline acoustic positioning system. The system presented here is an above-water, air-based prototype for an underwater acoustic positioning system; it is designed to determine the position of remotely-operated underwater vehicles (ROVs) and autonomous underwater vehicles (AUVs) in the global frame using a method that does not drift over time.

A ground-truth positioning system is constructed using a stacked hexapod platform actuator, which mimics the motion of an AUV and provides the true position of an ultrasonic microphone array. An ultrasonic transmitter sends a pulse of sound towards …

Towing Tank Trials Of Hydrokinetic Turbine Scale Model To Support Marine Energy System Verification, Shahab Rouhi

LSU New Orleans Theses and Dissertations

In response to the escalating demand for sustainable energy solutions and the critical reevaluation of conventional fossil fuels due to environmental concerns, this dissertation embarks on a comprehensive exploration of hydrokinetic energy as a promising alternative. The study delves into the underexplored domain of hydrokinetic energy, leveraging innovative methodologies for effective utilization and harnessing, particularly through the development and investigation of hydrokinetic turbines.

In the realm of hydrokinetic energy conversion, our research has exclusively concentrated on horizontal-axis turbines, distinct from other turbine configurations. Noteworthy is the adaptation of a conventional horizontal-axis wind turbine for water currents, revealing enhanced performance through …

Garbage Float, Gabor Papp, Max Woolverton, Scott Ulatowski, Daniel Ross, Nicholas Gayle, Bryan Merchan-Aragon, Noah Yco, Nicholas Fawcett, Jared Wright, Abdulaziz Salman G Alshahrani, Andrew Mcquire

Mechanical and Civil Engineering Student Publications

Trash pileup in our waters is an increasing problem. Removing floating plastics and debris from our ecosystem would reduce mortality rate of marine animals. Solutions for this already exist but most of them are proprietary and expensive. Therefore, an autonomous, publicly available and cheap alternative was developed to skim and clean the water surface from garbage.

Design, Testing And Neural Network Modeling Of A Low-Friction Wave Energy Converter Testbed, Vasu Bhardwaj

Dissertations, Master's Theses and Master's Reports

Point absorber wave energy converters (WECs) transform water wave kinetic energy into other useful forms, typically electrical. While it’s possible to extract energy from passive WECs, more energy can be captured using active control where its power take-off (PTO) acts as both a generator and an actuator. Control strategies usually require accurate models often obtained during model-scale testing. Unfortunately, friction can dominate the dynamic response in small WEC models. A frictionless point absorber WEC testbed is described in this report which allows the researcher to focus on fundamental hydrodynamic behavior instead of friction. It uses air bearings for vertical motion …

Ballasting System For An Autonomous Underwater Vehicle, Noura Rayes, Bahram Nassersharif, Zach Champney, Kyle Alessandro, Jason Mirandou

Senior Honors Projects

NOURA RAYES (Mechanical Engineering); Ballasting System for an Autonomous Underwater Vehicle Sponsor: Bahram Nassersharif (Mechanical Engineering)

Over the last year, our Mechanical Engineering Capstone team, Nautilus, has been working to design a ballasting system for various Autonomous Underwater Vehicles (AUVs) sponsored by Raytheon Technologies. Common AUV systems are used for a wide range of applications from environmental monitoring, oceanic exploration, to data collection. AUVs also have many technical advantages that make underwater tasks more efficient, cost-effective, and generally safer. Raytheon Technology, specifically, is looking to improve their existing ballasting mechanism for their AUVs to use for military defense. For this …

Deep-Sea Water Collector, Chandler Jones, Jenny Verheul, Michael Di Giorgio

Mechanical Engineering

Properties such as nutrients, DNA, pH levels, and primary productivity are difficult to measure onboard an Underwater Remotely Operated Vehicle (UROV) as mobile submarine sensors are highly expensive and conventional water capture devices are too large to be equipped. However, these properties provide an integral view into our oceans, the species that inhabit them, and our influence on the environment. Collected samples of seawater taken back to labs allow researchers to see a clearer picture of ecosystems’ inhabitants and lifecycle with the analysis of Environmental DNA (eDNA) among many other properties. The scope of this project is to design a …

Geometric Optimization Of A Heaving Point Absorber Wave Energy Converter, Ian Riley

College of Graduate Studies: Theses & Dissertations

Wave energy shows significant potential for development into a competitive renewable energy source. Non-renewable resources are finite and contribute to adverse effects on the environment. Development of wave energy conversion devices that use heave motion as the primary driver for converting wave energy into electrical potential is explored through optimizing the geometry of an axisymmetric partially submerged buoy in deep water. The governing equations of motion and hydrodynamic forces are solved for in one degree of freedom using ANSYS Aqwa. An external PTO device is simulated to induce power capture in the system. Four different geometric shapes are tested and …

Micro-Spi Sediment Profile Imaging Micro-Inspector, Andrew P. Corvin, Caleb T. Davies, Matt R. Ferrari

Mechanical Engineering

This project was proposed by Dr. Brian Paavo through a desire to more easily study the benthic sediment layers of the ocean. To do so, he asked us to build a simple and compact machine for use in sediment profile imagery (SPI). Although devices like this already exist, they are all large scale devices that require a ship with a crane to deploy, which is expensive and time consuming. Instead, he desired a “micro” SPI, which is capable of being deployed from a small vessel that can easily navigate shallow waters. Our interpretation of these requirements was as follows: a …

Marine Gastrobot Final Design Report, Wesley B. Williams, Eric Kane Dreischerf, Tommy Nicholas Yath

Mechanical Engineering

The Marine Gastrobot sponsored by Dr. Christopher Kitts of the Cal Poly Center for Applications in Biotechnology was a research and development effort intended to explore the use of microbial fuel cell technology as a power source for underwater robots. Our team Ocean Locomotion succeeded in developing a first iteration of an underwater robotic platform suitable for microbial fuel cell integration. The primary feature of the design is its sinusoidal fin propulsion intended for benthic exploration with limited risk of entanglement. During the course of development, Ocean Locomotion explored the use of low power actuation methods and determined their limited …

Developing A Curriculum For Marine Mechatronics Technicians, Vukica M. Jovanovic, Petros J. Katsioloudis, Ana Djuric, Mileta Tomovic, Thomas B. Stout

Engineering Technology Faculty Publications

A growing trend within the U.S. Navy is to streamline operations by deploying ships with less sailors, who are more highly skilled technicians that are trained to do a wide array of jobs. Modern ships also include various automated systems that require more highly skilled technicians for maintenance. Outdated warship designs are now being replaced with industrial grade automation equipment. Such equipment is being used in warships that encounter harsher environments than what exists in the civilian industry. Hence, there is a need for training in regards to industrial grade automation equipment for military and civilian ship repair partners. Marine …

Biomimetic Seal Flipper Test Rig, Gordon D. Belyea, Laura Kawashiri, Dylan Rinker, Kurt Beske

Mechanical Engineering

No abstract provided.

Electromechanics Of An Ocean Current Turbine, Vasileios Tzelepis

LSU New Orleans Theses and Dissertations

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 …

Hydromodus: An Autonomous Underwater Vehicle, Alex Kost, Anu Mahinkanda, Jordan Read

Electrical Engineering

Hydromodus is a student-led multidisciplinary project conceived by Jordan Read designed to provide a low-cost modular hardware and software solution for researchers and scientists. For the scope of the Senior Project class, it is designed to be a baited remote underwater vehicle (BRUV), but the platform is highly modifiable and open-source.

Marine Current Energy Devices: Current Status And Possible Future Applications In Ireland, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

There is a growing demand for the use of renewable energy technologies to generate electricity due to concerns over climate change. The oceans provide a huge potential resource of energy. Energy extraction using marine current energy devices (MCEDs) offers a sustainable alternative to conventional sources and a predictable alternative to other renewable energy technologies. A MCED utilises the kinetic energy of the tides as opposed to the potential energy which is utilised by a tidal barrage. Over the past decade MCEDs have become an increasingly popular method of energy extraction. However, marine current energy technology is still not economically viable …