Manufacturing Commons^™

Wart Eliminator Project Report, Colton Story, Kyle Shipman

Industrial and Manufacturing Engineering

The Wart Eliminator is a product based on the theory of resonant frequency and its ability to devitalize pathogens with the use of electronic pulses. Using the resonant frequency of the wart’s pathogen, the device is operated by the user with two switches for power and a probe connected by a wire to the device for applying to the affected area of the user while running three minute cycles. The product is in the beginning stages with only a prototype made. The product needed a proper ergonomic design to be easily used by the user and a cost analysis to …

Simulating The Flow Of Students Through Cal Poly's Undergraduate Industrial Engineering Program For Policy Analysis, Alexander Clayton Weber

Industrial and Manufacturing Engineering

The purpose of this project is to analyze the flow of Industrial Engineering students at California Polytechnic University San Luis Obispo in order to measure various graduation metrics by use of a simulation. Currently, graduation rates are relatively low in comparison with the rest of the state of California and future growth and decreased budgets may threaten graduation rates for incoming students. This simulation will identify bottleneck classes [those that hold up students from graduating] and provide a basis for a sensitivity analysis in which different scenarios are constructed to determine their effects on graduation metrics. The simulation will offer …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Application Of Systems Engineering And Project Management For Algae Photo Bioreactors, Andrew S. Balberchak

Industrial and Manufacturing Engineering

EXECUTIVE SUMMARY

Today there is much talk about different sources for biofuel to replace the decreasing supply of fossil fuels. Algae seem very promising with its abundance across the globe and relatively simple growing conditions. Lipids can be extracted from this organism which is then converted to biofuel. Although biofuel production from algae is not economically viable at this stage, researchers are suggesting using the by-products of algae for supplemental and healthcare use. If true, this could justify the economics of obtaining fuel from algae by creating more markets from various algae products.

Cal Poly State University’s Food Science and …

Convertible High Heel Design, Mathew Caspari, Tyler Shelton

Industrial and Manufacturing Engineering

Many women feel pain and discomfort when wearing high heels to certain events. This is a problem because it can lead to a variety of health issues. It would be beneficial and convenient if a woman could remove the heelpiece from her shoe while still wearing the same product. However, there is currently no popular high heels that can convert to a flat shoe on the market today. Our goal was to perform an in depth human factors analysis with regards to high heel use and formulate a solution to these problems. After reviewing literature, conducting a survey, and analyzing …

Thermal Characterization Of A System On Chip (Soc), James Gilstrap

Industrial and Manufacturing Engineering

Electronics are getting more and more advanced. Companies are designing their product to be more powerful, but at the same time they are designing them to be smaller and more user friendly. Heat becomes a major factor with the limited amount of surface area. The objective of this project is to measure the junction temperature of three system on chips (SoC) under various loading conditions and their time constant. The junction temperature was measured based on the diode’s I-V linear relationship. Both calibration and measurement of the junction temperature were conducted for three different SoC packages. The measurement results can …

Reason-To-Reuse: A Sustainable To-Go Food Storage Container System For Restaurants, Ryan Christopher Labuda

Industrial and Manufacturing Engineering

A food storage container (FSC), also known as a to-go box, is a very popular way for Americans to pick up food when in a rush and take it with them or store leftovers after dining. Some of the more popular materials that make up FSCs include Styrofoam, paper and plastic. These FSCs are meant for one time use and subsequently the majority end up as waste in their local regions. Reason-To-Reuse is a sustainable business that provides an alternative to the current model of disposable FSCs at restaurants by cutting down on waste. The objective of the Reason-To-Reuse project …

Design And Analysis Of A Materials Management System For Boeing Commercial Airplanes' (The Boeing Company) Metallic Raw Material Supply Chain With A Focus On Lead Time Manipulation And Corresponding Effects On Inventory And Cost, Henry Lu

Industrial and Manufacturing Engineering

The purpose of this project is to identify the costs associated with an aggregation strategy run by Boeing Commercial Airplanes. In order to identify these costs, a rudimentary replenishment system must be designed for the supply chain due to the fact that there is currently no such system in place. This replenishment system will be used to create a model (created in Excel) to calculate the total annual costs of the system. The model must allow changes to some of the important inputs such as mill performance measures and lead times and report the resulting changes in the total annual …

Companion Pass Program, Andrew Toney

Industrial and Manufacturing Engineering

At the end of each quarter the students of Cal Poly prepare to sign up for their classes for next quarter. This process is more difficult for seniors who must meet very specific requirements in order to graduate on time. Students can spend hours trying to find the “perfect schedule”, that one schedule that fits their personal schedule and their graduation requirements, while not over taxing themselves during that quarter by having too much class work. This Cal Poly explores the creation and implementation of an extra scheduling tool to address the weaknesses of the current scheduling system, PASS, and …

Bicycle Mounted Iphone 5 Case With Charging System, Patrick Goebel

Industrial and Manufacturing Engineering

This purpose of this project is to design and manufacture a bicycle handlebar mounted case that will house Apple’s iPhone 5 and a charging system that utilizes a charge from a generator hub in the front wheel of a bicycle. The charging system and software for this project will be developed by an Electrical Engineering Graduate student. The case and charging system must be a self-contained unit that is weather-proof and aesthetically pleasing. It must allow the user to use all of the features of the iPhone 5 under a wide range of speeds. It must be adjustable between portrait …

Analyzing The Costs Of Different Energy Storage Systems For California Polytechnic State University, Christian Royer

Industrial and Manufacturing Engineering

The goal of this project was to analyze the different ways to release energy from an energy storage device into the grid to save money. This project was worked in conjunction with a Master’s of Science student. An entire year of Cal Poly’s energy usage was examined and multiple trends were observed about when the maximum amount of energy was used. These trends looked at the time of day, the day of the week, and season to see what would be the best way to release energy into the grid to save money. There were two different batteries sizes examined …

The Decision Process Of Transitioning From A 3-Axis To A 4-Axis Or 5-Axis Mill Machine, Andrew Van Cleve, David Sherman

Industrial and Manufacturing Engineering

Companies are always looking for new ways to increase productivity and help the company save money. The way this is done is by researching new and more efficient ways to produce whatever it is the company is selling. Since there are always new technologies coming forward it can be difficult to distinguish which ones are viable and which ones are not. This paper looks at the decision of moving a company from a traditional 3-axis milling set-up to a 4-axis or 5-axis milling set-up. Through research and analysis this report will guide a company through the decision making process and …

Reducing Customer Wait Time And Improving Processes At Abc’S Atv Rentals, Thomas Allen Merrill Jr.

Industrial and Manufacturing Engineering

This project serves to explore the system bottlenecks of a small, family owned ATV rental company. The main objective is to reduce the average time a customer spends in the system, focusing on customer wait time as well as other areas that can be improved. This was done by collecting time studies and inputting the values into simulation software, which was run to represent the current system as well as various other possible scenarios encountered by rental companies. While creating the simulation, adaptive techniques were incorporated into the simulation. These techniques aim to increase the durability and reusability of the …

Evaluation And Redesign Of Potting Shed For The Non-Profit Organization, Growing Grounds Farms, Adya Sinha, Julianna Levy

Industrial and Manufacturing Engineering

Growing Grounds, a local nonprofit organization, operates as a fully functioning nursery in San Luis Obispo. Their planting facility is outdated and the process is inefficient. They have new funding available and need to determine if they should automate certain processes or improve existing methods. This report details the current process and presents two possible ergonomic solutions and the accompanying layouts and improvements. An analysis is conducted to determine which new layout is recommended for Growing Grounds based on their current production and revenue, and future recommendations are given.

Edwards Lifesciences - Skirt To Frame Attachment Manufacturing Aid, Samuel Joda, Cesar Grimaldo, Patrick Hutchinson

Mechanical Engineering

No abstract provided.

Drape Forming Machine, Adam Johnson, Will Schlosser, Brian Miller

Mechanical Engineering

The goal of this project was to build a prototype machine that formed multiple sheets of debulked pre-preg OOA carbon fiber into a 2-foot long trapezoidal shape. The machine was required to do this process semi-automatically.

Rapid Decompression Containment System, Evan Domingue, Michelle Rudney, Daniel Trees

Mechanical Engineering

Cal Poly students; Evan Domingue, Michelle Rudney and Daniel Trees; are working with General Atomics Aeronautical Systems, Inc. (GA, ASI) and engineer John Wilcox to complete a senior project. The senior project is focused on finding a solution to meet the requirement set forth in MIL-HDBK 1791 4.2.5.2 for rapid decompression which requires cargo items to be designed with pressure relief devices or to be configured for air shipment as to prevent any part from becoming a projectile in the event of catastrophic loss of aircraft cabin pressure. The goal of this project is to design a safe, cost-effective, and …

Titan 130 Engine Aft-Mount, Woody Newell, Michael Haworth, Dylan Perry

Mechanical Engineering

No abstract provided.

Exploration Station Kidshake Table, Jeremy Duhe, Philip Hopkins, Matt Ostiguy, Samantha Weiner

Mechanical Engineering

The KIDShake Table is an all mechanical earthquake shake table sponsored by the Exploration Station Children's Museum of Grover Beach. This interactive exhibit has two working mechanisms, a hand crank and pull rope, that provide two axis movement for knocking down block structures. This table was built and designed for a target age of 10 years.

Beach Wheelchair Project, Rory Aronson, Joshua Marcum, Samuel Coyne, Alex Hayes, Alexa Colburn, Max Hessel, Benedikt Strauss, Marvin Rimmele, Marco Pietsch

Mechanical Engineering

The Beach Wheelchair, Sandcrawler, is a machine intended to help give people with disabilities the full beach experience. The non-profit organization Bridge II Sports sponsored this project, and tasked us with developing the design and fabricating a prototype. This chair has several features including a linkage mechanism that raises and lowers a chair relative to an external frame, hand crank drive with Gates Carbondrive belt and sprockets, buoyant Wheeleez balloon tires, and much more.

Rebounder Fatigue Test Machine, Caroline Reeves, Will Robertson, Ethan Flory

Mechanical Engineering

JumpSport, a company that designs and sells trampolines and trampoline accessories, has sponsored this senior project team to design, build, and test a trampoline fatigue test machine. The machine must simulate a person jumping on the trampoline to test the life of JumpSport’s fitness trampolines and kids’ trampolines. Partway through the design process, the objectives were altered and this senior project team was tasked with merging with another Cal Poly senior project group to create an all-inclusive test machine to accommodate both full-trampoline testing and individual bungee cord testing.

The final design is centered on a slider crank linkage driven …

Human Powered Helicopter: Spars, Jason Addy, Sterling Fuentes, Graham Garvin, Kenneth Girardin, Lipski Timonthy, Daniel Logue

Industrial and Manufacturing Engineering

Abstract

Neal Saiki, a Cal Poly alumnus, donated a human powered helicopter to the Cal Poly Aircraft Design and Construction Club in Fall Quarter 2012. To achieve the requirements of the Igor Sikorsky Human Powered Helicopter Competition, this senior project was tasked with reducing the weight of the load-bearing spars without changing geometry.

The aluminum spars were replaced with carbon fiber. The spars were designed to maintain the bending and torsional stiffnesses. Twelve sections of carbon fiber tubes ranging from 8 to 12 ft in length and 2" to 3" in inner diameter were made using pre-preg carbon fiber wrapped …

S&G Metal Fab Battery Tray, Matthew Nartatez

Industrial and Manufacturing Engineering

This report was written for the design of a battery tray and manufacturing process for S&G Metal Fab. The manufacturing steps of how to process the sheet metal to create the product are defined and documented in this report. This project began with constraints given by S&G and were all accomplished using coursework knowledge obtained as a manufacturing engineer student at Cal Poly San Luis Obispo. This report mainly covers parameters regarding the cutting, bending and, deforming of sheet metal to acquire the desired shapes and sizes. It also analyzes the costs that are associated with these processes and material. …

Loaded Shift Tester Sram, Nick Cox, Sam Shaffer, Michael Polka

Mechanical Engineering

This report details the design, manufacturing, and testing of a loaded shift tester for the SRAM Bicycle Corporation. The machine is used to perform developmental and qualification tests on various bicycle drivetrain components. Using SolidWorks, the design team created a solid model of the machine on the computer, then ordered and manufactured the parts required to build it. The machine was tested to ensure that all the parts worked together, and was finally delivered to SRAM when it was deemed ready.

Bicycle Wheel Test Machine, Dylan Harper, Kevin Hom, Ross Williams

Mechanical Engineering

In recent years, the cycling industry has witnessed huge advancements in bicycle components and materials. The age old goals of speed and low weight are still present today, but the pursuit of these goals may be reducing the structural stability of various components integral to wheel performance, including the wheel hub bearings. These bearings are invaluable to bicycles but little is known about how the forces and loads applied to a bicycle affect the performance of these bearings. Broken axles and hubs are indicators of significant stresses within the hub, but little is known about how the resulting deformation affects …

Hoist To Transfer Athletes From Wheelchair Into A Kayak, Jennifer Batryn, Javier Mendez, Kyle Mooney

Mechanical Engineering

No abstract provided.

Ir Imaging Chip Fixturing System, Curtis Wagner, Scott Solomon

Mechanical Engineering

No abstract provided.

Human Powered Hydrofoil Bike Pontoon Floatation, Shelley Dangoor, Tyler Brennent

Mechanical Engineering

This report documents the brainstorming and design development of the hydrofoil bike floatation device. This project is in conjunction with senior project team MobyBike. MobyBike’s focus is in the development of the bike actuation system, as our team’s focus is on designing and developing the floatation device to be incorporated in the final hydrofoil bike design.

Guidance System, Kayaking For The Visually Impaired, D. Ryan Kirtland, Ryan Phife, William Gardner, Amy Johnson

Biomedical Engineering

Quality Life Plus is working with Team River Runner to develop an assistive guidance system for veterans who want to remain active by kayaking, after sustaining an injury that impairs vision. This system allows these veterans to complete a slalom speed race independent of a personal guide in the water. The system incorporates 3 stations that each contain a speaker connected to a microcontroller system covered by a Pelican Case on a custom made buoy. During the slalom race, a kayaker will travel from shore towards buoy #1 as it omits sound from the speaker. As the kayaker moves around …

Reliability Analysis Of Low-Silver Bga Spheres Comparing Failure Detection Criteria, Briana Fredericks

Industrial and Manufacturing Engineering

One of the challenges of solder joint reliability tests is estimating the time of failure of the solder joint. Failure criteria should be able to detect solder joint failure as early as possible, while minimizing the probability of false detection. The failure mechanism under study is cracks due to thermal fatigue. The most common method to estimate failure due to cracks is to monitor the resistance during testing, because solder imaging and cross-sectioning methods are destructive. Current industry failure criteria do not adequately demonstrate the relationship between the size of the crack and the resulting change in resistance. This project …