Manufacturing Commons^™

Structural Design And Finite Element Analysis Of A 54 Ton Freight Wagon Bolster Test Rig Under Vertical Center Plate Load, Shandy Dwi Prayoga, I Dewa Gede Ary Subagia, I Ketut Adi Atmika, Abdul Rohman Farid, Yunior Lanang Satrio

Journal of Mechanical Engineering Science and Technology (JMEST)

Bolster is one of the bogie's components that receives direct loading from the car body and freight movement. One of the problems that occurs in the bolster is permanent deflection during vertical and transversal static loading. Therefore, a static loading test is required to evaluate the structural strength of the bolster. During the static loading test, a rig is required to hold the bolster so that the bolster is in a fixed position. The rig owned by PT. INKA (Persero) showed a plastic deformation at the vertical center plate load (VCP 5.22P). Therefore, a modified design of the rig is …

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Foldable Transfer Platform, Toby Sagi, Ashton Heiati, Triton Johnson, Zachary Denis

Mechanical Engineering

The report details the design and results of a Hoyer lift to transfer patients between wheelchairs and our sponsor's, Beacon VTC Santa Maria, vans. The lift disassembles into 3 main pieces, allowing the lift to be stored in the back of the van. The lift uses a hydraulic actuator to rotate the boom. We handed over our project to Beacon VTC Santa Maria for use in their facility!

Cal Poly Fluid Powered Vehicle Challenge 2025/2026, Ethan Malachi Nejame Zeiset, Christian Anthony Cuamani, Daniel Chacon-Bizarro, Marcus Minera, Bradley Hansell

Mechanical Engineering

In this Final Design Report, the Cal Poly Fluid Power Vehicle Challenge Contending Team competed in Sun Hydraulics’ 2026 Fluid Powered Vehicle Challenge. The objective of the competition is to expose college students to the fluid power sector, the “hidden giant” of the engineering industry. Specifically, student teams are tasked with the development of a human-powered, fluid-driven vehicle for use in various competitive settings. The team prioritized the optimization of an existing prototype for simplicity, ease of maintenance, and reliability during the competition. The existing prototype exhibited issues related to the main frame’s deflection under load, a lack of gear …

Niu Fsae Brake Rotor Design & Flywheel-Based Test Stand Development, Cody J. Marko, Austin Coyne, Alexander Boyden

Honors Capstones

This project addresses the need for a reliable and validated brake rotor for the Northern Illinois University Formula SAE vehicle following a prior catastrophic rotor failure within the team. Brake rotors in high-performance applications are subjected to significant thermal and mechanical loads, and inadequate design can lead to failure, posing serious safety risks and limiting vehicle performance. To solve this issue, a new brake rotor was designed alongside a dedicated test stand to both improve braking performance and enable experimental validation. The rotor was evaluated using finite element analysis (FEA), including transient thermal and structural simulations, to predict maximum temperature, …

Design And Development Of A 12-Degree-Of-Freedom Quadruped Robot, Kai De La Cruz

Master's Theses

This thesis presents the design, analysis, and experimental validation of a 12-degree-of-freedom (DOF) quadruped robot developed as a research platform for legged locomotion and control. The system builds upon the Cal Poly Legged Robotics Group’s prior 8-DOF quadruped, addressing key limitations in manipulability, load distribution, and mechanical robustness by introducing a 3-DOF leg architecture.

The mechanical design emphasizes lightweight construction, structural integrity, and modularity to support future research extensions. Static and dynamic loading models were developed to inform component sizing and material selection. A carbon-fiber chassis and redesigned leg assemblies were fabricated and validated through finite element analysis and physical …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

Akron Soap Box Derby Super Kids Car, Alexis Schultz, Cooper Sites, Sean Stevenson

Williams Honors College, Honors Research Projects

This project aims to redesign the All-American Soap Box Derby Super Kids vehicle to enhance safety, accessibility, and performance while maintaining full compliance with official regulations. The Super Kids program enables children with physical and cognitive disabilities to race alongside a co-pilot, but the current vehicle design presents challenges in stability, entry/exit accessibility, and control—especially following recent regulation changes that increased vehicle speed. The redesigned car will focus on improved ergonomics, lightweight construction, and structural integrity within a $1,000 budget and a 165 lb weight limit.

An iterative engineering design process will guide the project through research, CAD modeling, FEA …

Evaluation Of The Long-Term Sealability Performance Of Aramid Fiber Nitrile-Based Gaskets, Salome Ramirez

Honors Undergraduate Theses

The reliability of sealed, oil-filled containers is critical for maintaining the operation of high-voltage energy systems, in which the sensitive electronics need to be isolated from the cyclic conditions associated with outdoor environments. New materials bring the possibility of extending service lifetimes and maintenance intervals. Aramid fiber nitrile-based gaskets are an attractive alternative to conventional gasket choices due to their long-term stability in various environments and compatibility with porcelain, metals, and plastics. For newly designed porcelain-to-metal fittings, understanding the behavior of the candidate gasket material under realistic loading conditions is essential to ensure long-term seal integrity and equipment safety. Traditional …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Process Optimization And Quality Control In Manufacturing Of Frp Composites By Vartm, Mohamed Emadeldin Omar Abdelhadi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Railroad tank cars, being one of the most used means of transportation of hazardous material across the country, have not been structurally upgraded for a long time. Thus, the Pipeline and Hazardous Materials Safety Administration (PHMSA), a United States Department of Transportation (USDOT) agency, released a rule for safer transportation of highly hazardous and flammable liquids by railroad to enhance the design specifications of both the new and existing tank cars in May 2015. A multifunctional composite jacket is proposed as a new material to structurally enhance the railroad tank cars to withstand any accidents that could happen en route. …

Experimental And Numerical Study On The Influence Of Carbon Fiber Reinforcement On The In-Plane Compressive Properties Of 3d Printed Hexagonal Honeycomb Core Structures, Deon Wallace

All Theses

There is difficulty with numerically replicating the behavior of composite honeycomb core structures numerically due to the trouble of gathering material properties from a hollow structure. Also, complex part geometries and carbon fiber reinforcement strategies can lead to unwanted structural weaknesses and variance in material properties that may not be reflected in numerical analysis when the part is additively manufactured. In this study, edgewise compressive testing is used to characterize the mechanical behavior and performance characteristics of these structures. The experimental results indicate an increase in the Young’s moduli of the honeycomb core structures as carbon fiber concentration increases. However, …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Predicting Leakage From Nuclear Material Containers At Los Alamos National Laboratory Through Drop Testing, Leak Testing, Finite Element Analysis And Digital Image Correlation, Jude M. Oka, Yu-Lin Shen, Osman Anderoglu, Pankaj Kumar, Rajendra Vaidya

Mechanical Engineering ETDs

Los Alamos National Laboratory (LANL) relies on containment vessels to safely manage special nuclear material. These containers are subject to rigorous testing—such as drop, fire, and water ingress testing—to ensure integrity under adverse conditions. While elastomer-based seals are well studied, metal-to-metal sealing mechanisms remain under investigation, particularly under dynamic loading. This research focuses on the relationship between container mating surfaces and impact loading through drop testing. Finite Element Analysis (FEA) models were developed and validated using Digital Image Correlation (DIC) to measure strain during impact. Drop tests at varying heights showed strong correlation between FEA and DIC results, confirming the …

Lidss Raft Battery Pack Integration, Jack Maxwell, Vincent Stevens, Matthew Hoodmaker, Colin Flanders

Mechanical Engineering

Lawrence Livermore National Laboratory is a critical member of the United States Department of Defense. Their Independent Diagnostics Scoring System (LIDSS) uses rafts that operate in the ocean to collect missile test data. Several times a year, the United States will test their Inter-Continental Ballistic Missiles by launching them into the ocean near the Marshall Islands. This is where the LIDSS rafts collect their test data. Our project was centered around re-designing the battery pack used by the rafts. The current battery pack design experiences water ingress problems and is difficult to access. Our re-designed battery pack is waterproof to …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

From Concept To Light: Manufacturing A Dual-Purpose Bedside Lamp And Book Organizer, Nicole Goulet

Honors Theses

This report features the design, development, engineering changes, and manufacturing of the Bedside Lamp, a hand-made multi-purpose lamp, book holder, and charging hub. The investigation began with research and a market analysis on current lamp designs and a discussion about what features would set the lamp apart. This led to the design of the lamp and construction of multiple prototypes for proof of concept.

A manufacturing process was then designed to demonstrate the steps to start up an efficient and cost-effective production line. This process included obtaining raw materials, cutting them into the necessary parts, and assembling everything to create …

Computational Modeling Of Torque Arm And Load Cell Interactions In Uta Racing Brake Dynamometer, Anthony A. Aiyedun

2025 Spring Honors Capstone Projects - Archive

The UTA Racing Team is developing a brake dynamometer to measure the coefficients of friction of various brake pads and calipers under controlled conditions. The dynamometer simulates on-track braking scenarios, testing brake pads at temperatures up to 1300ºF and pressures similar to racing environments. Its primary goal is to generate accurate friction vs. temperature graphs for various brake pad and rotor combinations, addressing the need for dedicated testing equipment. This project creates an ANSYS simulation of the torque arm and load cell interaction. The computational model accurately represents the relationship between applied torque and measured load cell force, incorporating precise …

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Improving The Viability Of Continuous Fiber Reinforced Composite Materials In Extreme Temperature Applications And Additive Manufacturing, Ryan A. Warren

Shelby Hall Graduate Research Forum Presentations

Presentation slides for a presentation given at the 1st annual Shelby Hall Graduate Research Forum at the University of South Alabama.