Heat Transfer, Combustion Commons^™

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

LSU New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Study On The Integration Of A Novel Absorption Chiller Into A Microscale Combined Cooling, Heating, And Power (Micro-Cchp) System, Scott J. Richard

LSU New Orleans Theses and Dissertations

This study explores the application of micro-CCHP systems that utilize a 30 kW gas microturbine and an absorption chiller. Engineering Equation Solver (EES) is used to model a novel single-effect and double-effect water-lithium bromide absorption chiller that integrates the heat recovery unit and cooling tower of a conventional CCHP system into the chiller’s design, reducing the cost and footprint of the system. The results of the EES model are used to perform heat and material balances for the micro-CCHP systems employing the novel integrated chillers, and energy budgets for these systems are developed. While the thermal performance of existing CCHP …

A Numerical Study Of High Temperature And High Velocity Gaseous Hydrogen Flow In A Cooling Channel Of A Ntr Core, Sajan B. Singh

LSU New Orleans Theses and Dissertations

Two mathematical models (a one and a three-dimensional) were adopted to study, numerically, the thermal hydrodynamic behavior of flow inside a single cooling channel of a Nuclear Thermal Rocket (NTR) engine. The first model assumes the flow in the cooling channel to be one-dimensional, unsteady, compressible, turbulent, and subsonic. The working fluid (GH₂) is assumed to be compressible. The governing equations of the 1-D model are discretized using a second order accurate finite difference scheme. Also, a commercial CFD code is used to study the same problem. Numerical experiments, using both codes, simulated the flow and heat transfer …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Radiation Intensity Of A Turbulent Sooting Ethylene Flame, Ryan M. Hartman, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Turbulent sooting flame radiation is relevant to applications ranging from fire safety to gas turbine engines. The complex direct interactions of soot and radiation intensity are of particular importance when creating accurate soot prediction models. Previous studies have measured gas-band and broadband radiation intensity from turbulent sooting flames. The focus of the current study is the characterization of radiation intensity emanating from soot. A high-speed infrared camera (FLIR Phoenix) was used to acquire time-dependent quantitative images of radiation intensity of a turbulent sooting ethylene flame. The flame had a Reynolds number of 15,200 and was stabilized on a burner with …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Experimental Study Of Co2 Recycling Using Metal-Oxide Enhanced Coconut Char Gasification: Catalytic Effect Of Potassium Carbonate On Gasification, Mengqi Gao, Indraneel Sircar, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Biomass gasification is an important process in the production of bio-derived fuels and renewable energy. Biomass gasification with CO₂ is an endothermic process requiring high temperatures, resulting in low process-efficiency. Metals found in the ash in biomass feedstock have shown rate-promoting effects on the C-CO₂ reaction and have motivated the study of low-temperature catalytic gasification. The present study investigates the catalytic effects of potassium (K) on the biomass gasification reactivity of a coconut-derived char (>99.9% carbon) within the temperature range of 600 – 1000 ^oC. A wet-impregnation technique is used to prepare K-treated chars. Gasification of …

Combustion Measurement Of Counter Flow Diffusion Flame Under High Pressure Using Coherant Anti-Stokes Raman Scattering (Cars) Thermometry, Xianan Huang, Robert P. Lucht

The Summer Undergraduate Research Fellowship (SURF) Symposium

H₂-air combustion is widely employed in power generation systems and high speed propulsion systems which are high-pressure environments. Therefore, it is imperative to perform diagnostics in order to understand behaviors of H₂-air flames under high pressure to improve the design of systems such as those mentioned previously. In order to perform measurements at high pressure, a facility has been constructed for stabilizing steady-state, laminar counterflow diffusion flames (CFDFs). Both, qualitative and quantitative measurements will be performed in this high-pressure facility. Numerical simulations of high pressure, H₂-air flame structure are also being performed using COSILAB …

An Investigation Of Phase-Change Effects During Rapid Compression Machine Experiments, Colin Banyon

Master's Theses (2009 -)

Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, …

An Applied Numerical Simulation Of Entrained-Flow Coal Gasification With Improved Sub-Models, Xijia Lu

LSU New Orleans Theses and Dissertations

The United States holds the world's largest estimated reserves of coal and is also a net exporter of it. Coal gasification provides a cleaner way to utilize coal than directly burning it. Gasification is an incomplete oxidation process that converts various carbon-based feedstocks into clean synthetic gas (syngas), which can be used to produce electricity and mechanical power with significantly reduced emissions. Syngas can also be used as feedstock for making chemicals and various materials.

A Computational Fluid Dynamics (CFD) scheme has been used to simulate the gasification process for many years. However, many sub-models still need to be developed …

Numerical Modeling Of Heat Pipe Radiator And Fin Size Optimization For Low And No Gravity Environments, Virginia Ruth Bieger

UNLV Theses, Dissertations, Professional Papers, and Capstones

A heat-pipe radiator element has been designed and modeled to study the efficiency of heat transfer for low and no gravity environments, like in lunar environments. The advantages of using heat pipe includes the significant weight reducing and heat transfer efficiency. The heat transfer can be enhanced by the use of condenser sections with attached fins.

A series of various geometries of solid fins and heat pipes with and without fins were modeled using FLUENT®. This was done to determine the validity of using a heat pipe in lieu of a solid fin projection. A heat pipe had a 25 …

Flame Temperature Imaging Of A Low Nox Burner Via Laser Rayleigh Scattering, Nicholas A. Smith

Master's Theses (2009 -)

Federal and global legislation are requiring increasingly stringent emission regulation on household appliances and in particular water heater burners. Emissions like NOx (NO and NO2) are a growing concern due to their adverse health effects and contribution to tropospheric ozone, acid rain, and smog formation. As NOx is more closely controlled, appliance manufacturers are developing low emission burners for use in water heaters.

Flame temperature is strongly correlated to NOx production. Hence, characterizing flame temperatures in new burners is a key part of improving upon burners used today and the development of future burners. Temperature measurements applied to a new, …

Investigation Of Thermal Properties And Latent Heat Reduction Mechanisms In Nanofluid Phase Change Materials, Aitor Zabalegui

Mechanical Engineering Master's Theses

The thermal properties of paraffin-based nanofluids have been examined to investigate the use of enhanced phase change materials (PCMs) for thermal energy storage (TES). PCMs are promising for TES applications, but low thermal conductivity limits their rate of heat exchange with a working fluid. The nanofluid approach has been established as a method of thermal conductivity enhancement, but effects of particle addition on other thermal properties affecting TES are relatively ignored. Significant reduction in latent heat of fusion below traditional effective medium theory has been observed in nanofluids. An experimental study of paraffin nanofluids, containing various diameter multi-walled carbon nanotubes, …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

Barbeque Grill Temperature Distribution Design Improvement, Peter Gobell, Connor Mcgill, Thomas Willson

Mechanical Engineering

Team License to Grill set out to asses Bull Outdoor Products, Inc.’s barbeques and quantify the apparent uneven temperature distribution or “hot spots” and “cold spots” across the grill. This testing was accomplished with the design and fabrication of a test fixture allowing for accurate and repeatable temperature collection across the barbeque. With results that matched the sponsor’s claims of hot and cold spots, an engineering model was made using heat transfer and thermodynamic equations. Once the model somewhat resembled the experimental data, it was used to suggest different modifications that would allow for better temperature distribution. It was discovered …

High Temperature Filter Test Unit Upgrades, Blair Frandeen, Will Schill, Erick Shewmaker, Joshua Turgeon

Mechanical Engineering

The purpose of this project was to improve the existing High Temperature Filter Test Unit (HTTU) by optimizing performance and adding new features. These features include viewing ports and a camera system for observation of tests, a leak detection system, and a flame impingement system. Additional considerations included improving the current operation of the HTTU by reducing test time and energy loss. The HTTU is designed to test High Efficiency Particulate Air (HEPA) filters at temperatures up to 1300 ˚F, creating conditions which simulate a fire in a chemical processing facility. The HTTU was originally built as a Cal Poly …

Rapid Tool Heating, Jason Chi, Bobby Dodge

Mechanical Engineering

Quatro Composites creates various molded parts for an array of industries. They are seeking to improve their thermoplastic molding process by decreasing the amount of time to heat up the steel tool that molds the thermoplastics. Currently, it takes approximately 1 hour to heat up their 120 pound steel mold from room temperature to approximately 700°F. The goal of this project is to create an optimum heating method that will minimize that heating time to about 20 minutes or less. It is critical for the stakeholders (Quatro Composites) to have a faster heating time in order to increase their production …

Rocket Fuel Pressurization, Sean Green, Joe Marcinkowski, Andrew Nahab

Mechanical Engineering

No abstract provided.

Numerical Characterization Of The Hydrodynamics And Thermal Behavior Of Air Flow In A "Flex-Duct" Air Distribution System, Samad Gharehdaghi, Samir Moujaes

College of Engineering: Graduate Celebration Programs

The aim of this research paper is to compute the hydrodynamic and heat transfer characteristics of the air flow inside a flexible duct used for residential/small commercial buildings. Various new information which manufacturers do not provide usually are produced numerically among which heat transfer coefficient, needed for estimating heat loss, is a principal one. Circulation zones in depressions are found to exist. It is shown that these regions act as an insulator and decrease the heat loss along the duct. The results show that fully developed conditions exist much earlier with regard to the inlet for both hydrodynamic and thermal …

Computational Analysis To Enhance Laminar Flow Convective Heat Transfer Rate In An Enclosure Using Aerosol Nanofluids, Andrew Hudson

College of Graduate Studies: Theses & Dissertations

The current research intends to provide a starting point to effectively model aerosol heat transfer in a narrow, enclosed body. This research can lead to future modeling of nano fluids including their heat transfer characteristics and erosion effects on the walls of an enclosure. The model was developed using ICEM CFD for the mesh and FLUENT for the fluid flow modeling. Six different aspect ratio enclosures were developed to study the effects of varying aspect ratio. The natural convection of air was developed first to establish the appropriateness of the models being used. A mesh check was performed using one …

Film Cooling In Fuel Rich Environments, Jacob J. Robertson

Theses and Dissertations

The ultra compact combustor is a high performance gas turbine design concept that portends reduced weight for future weapons platforms. A natural outcome of the design is the continual presence of fuel-rich air in the turbine component of the engine. Because modern cooling schemes for hot section turbine blades involve injecting cool, oxygen-rich air adjacent to the surface, the potential arises for reaction with the unconsumed radicals in the mainstream ow and augmented heat transfer to the blade. This outcome is contrary to the purpose of film cooling, and can lead to early life-cycle turbine failure. This study examined the …

Design And Testing Of An H2/O2 Predetonator For A Simulated Rotating Detonation Engine Channel, Stephen J. Miller

Theses and Dissertations

A study is presented on the relationship between a pre-detonator and a detonation channel of an RDE. Testing was conducted on a straight narrow channel made of clear polycarbonate windows connected to an H2/O2 pre-detonator to simulate the RDE initiation scheme and allow for flow visualization. A comparison is made on decoupling distance and wave velocities for a range of pre-detonator designs, inclination angles, equivalence ratios and geometries placed within the simulated channel. Regardless of inclination angle or equivalence ratio the detonation wave decoupled within 25 mm from the pre-detonator exit into the channel. A step change in diameter 25 …

Kase, The Laptop Cooling Case, Jana Morrison, Tyler Ries

Biomedical Engineering

This report describes the final design and analysis of a laptop cooling case as a marketable product for a group of entrepreneurial marketing student based out of California Polytechnic State University San Luis Obispo. Background market research and empirical measurements were taken in order to confirm that this would be a marketable product worth designing. Then previous solutions were researched in order to identity weaknesses and strengths. After rigorous research, it was determined that a passive cooling system, in which channels directed airflow to the computer fan would be the best system in terms of functionality, performance, and cost. A …

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Numerical Analysis Of The Thermodynamic Properties Of Various Gaseous Species, Addison Alexander

Lewis Honors College Capstone Collection

In the field of Fluid Mechanics, the determination of various thermodynamic properties of substances is of utmost importance. Many calculations require values for internal energy or specific heats. If experimental data does not exist to facilitate these calculations, an approximation must be made. This report analyzes three different approximation approaches to examine their relative strengths and weaknesses. The first approach, the Exact Method, uses NASA thermodynamic data to give a numerical interpolation. The second, the Summation Method, breaks up the total energy of the species into different contributions and performs an approximation based on thermodynamic theory. Finally, the Spectroscopic Method …

A Simplified Model Of The Internal Combustion Engine, Christofer Neff

Undergraduate Journal of Mathematical Modeling: One + Two

This project further investigates a model of a simplified internal combustion engine considered by Kranc in 1977. Using Euler’s method for ordinary differential equations, we modeled the interaction between the engine’s flywheel and thermodynamic power cycle. Approximating with sufficiently small time intervals (0.001 seconds over a period of 12 seconds) reproduced Kranc’s results with the engine having an average angular velocity of 72/sec.

Assessing And Mitigating Airborne Noise From Power Generation Equipment, Limin Zhou

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation examines the assessment and mitigation of airborne noise from power generation equipment.

The first half of the dissertation investigates the diagnosis and treatment of combustion oscillations in boilers. Sound is produced by the flame and is reflected downstream from the combustion chamber. The reflected sound waves perturb the mixture flow or equivalence ratio increasing the heat release pulsations and the accompanying sound produced by the flame. A feedback loop model for determining the likelihood of and diagnosing combustion oscillations was reviewed, enhanced, and then validated. The current work applies the feedback loop stability model to two boilers, which …