Heat Transfer, Combustion Commons^™

Residential Hvac Installation Faults: Field Prevalence, Drivers, And Energy Impacts, Seyed Ali Rooholghodos

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Faults in residential comfort systems can have detrimental effects on the performance of the system, reducing the energy efficiency, affecting indoor comfort, and shortening equipment lifespan. Many of the faults occur at installation. However, there has not previously been a systematic and nationally representative study to indicate the prevalence of the faults, meaning the distribution of faults by fault type and fault intensity. Understanding true fault prevalence is essential to be able to identify derivers, and to assess the incremental electricity consumption of the new installation systems.

This study presents on-site data from 341 new central cooling systems—air conditioners and …

Large-Scale Experimental Study On The Impact Of Air Cleaning & Ventilation On Indoor Air Quality And Student Illness-Related Absenteeism, Daud Nosham

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

This large-scale randomized experimental field study investigated the effect of portable air purifiers (PAPs) on classroom’s air quality and student’s illness related absenteeism. PAPs were installed in 317 classrooms from various school districts located in Eastern Nebraska. The classrooms were randomly assigned into four conditions: three treatment conditions (T1, T2 & T3) and one control condition (device without any filter). T1 was equipped with HEPA filters, T2 added Activated Carbon (AC) layer to HEPA, and T3 further integrated Germicidal Ultraviolet (GUV) alongside HEPA and AC filters. The measured variables were carbon dioxide (CO2), fine particles (PN2.5) and coarse particles (PNcoarse), …

Investigation Of Conductive Die-Top Thermal Capacitors During Short Circuit Operation Of Silicon Carbide Devices, Youssef Abotaleb

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) power devices have garnered significant attention in recent years due to their superior thermal and electrical properties compared to traditional silicon devices. However, SiC power devices suffer from severe reliability issues arising from their mechanical properties. This is because the Young's modulus of SiC is about three times larger than that of silicon, which correspondingly raises the mechanical stresses acting on the bonding structure, often leading to device failure under power shock events.

Traditional packaging materials and designs tend to constrain SiC performance, as hot-spot temperature resulting from a power shock is one of the key factors …

Investigating Near-Field Radiative Heat Transfer With Titanium Carbide Mxenes And Slanted Columnar Thin Films, Sean Luke Murray

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This work investigates the mechanisms to manipulate and control the magnitudes of Near-Field Radiative Heat Transfer (NFRHT) using two-dimensional materials and nanostructured surfaces. NFRHT occurs when the geometrical features of the radiating objects or the separation distance between interacting bodies are comparable to or lower than the characteristic thermal radiation wavelength. NFRHT magnitudes surpass the blackbody limit by several orders of magnitude due to phenomena such as photon tunneling and new modes of energy transfer, like surface polaritons. Therefore, it is crucial to understand how material properties and surface nanostructures affect NFRHT.

The first part of this work examines the …

Ultrashort Pulsed Laser Treatment Is Effective At Sterilizing Metal Surfaces For Planetary Protection, Kaleb Mcquillan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

To prevent forward contamination from microbes aboard spacecraft intended for exploration of solar system bodies there is a need for effective sterilization methods. However, current techniques are both time-consuming and expensive. For example, dry heat sterilization requires removal from the assembly site and several days of treatment. Furthermore, some components such as optics and electronics are not compatible with current sterilization techniques. In this thesis, a novel femtosecond laser surface processing technique for the rapid sterilization of spacecraft hardware is reported. Femtosecond lasers produce extremely high photon fluxes (10²⁹ photons/s*cm², ~0.03 J/cm²) in extremely short …

Mechanical Engineering Capstone: A Reflection On The Design And Prototyping Of A Portable Water Heating System, Timothy Goldsmith

Honors Program: Senior Projects (Public)

This thesis includes several documents from a Mechanical Engineering Capstone course. These include project postmortem reports written at the conclusion of each term. These reports summarize the designing and prototyping of a portable water heating system. Additionally, this thesis includes written feedback on the final presentations for six other senior design teams. In these documents, presentations and projects are evaluated and encouragement and feedback are provided for the teams. The final component of this thesis is an essay reflecting on the different leadership roles assumed during the capstone course.

A Review On Heat Flux Measurement Techniques In The Nano And Microscale, Miguel Moreno

Honors Program: Senior Projects (Public)

Heat Flux measurements represent an important step in obtaining an accurate heat transfer profile in many engineering problems. Sensors capable of measuring this quantity have been around for decades, however, the increasing focus in nano and microscale applications in the industry and academia demands more accurate and smaller devices. This paper reviews some of the methods used to develop heat flux meters targeted to nano and microscale, as well as some calibration processes for the same. A combination of Luminescence and non-luminescence methods for direct and indirect measurement of heat flux will be discussed. A glimpse of what the future …

Research Tools And Their Uses For Determining The Thermal Inactivation Kinetics Of Salmonella In Low-Moisture Foods, Soon Kiat Lau

Department of Food Science and Technology: Dissertations, Theses, and Student Research

The reputation of low-moisture foods as safe foods has been crumbling over the past decade due to repeated involvement in foodborne illness outbreaks. Although various pasteurization technologies exist, a majority are thermal processes and have not been well-characterized for pasteurizing low-moisture foods. In addition, the nature of a low-moisture food matrix introduces various experimental complications that are not encountered in high-moisture foods. In this dissertation, the development, building instructions, and characterization of various open source tools for studying the inactivation kinetics of microorganisms in low-moisture foods are described. The first tool is the TDT Sandwich, a dry heating device for …

Thermal Modeling Of Additive Manufacturing Using Graph Theory: Validation With Directed Energy Deposition, Jordan Severson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Metal additive manufacturing (AM/3D printing) offers unparalleled advantages over conventional manufacturing, including greater design freedom and a lower lead time. However, the use of AM parts in safety-critical industries, such as aerospace and biomedical, is limited by the tendency of the process to create flaws that can lead to sudden failure during use. The root cause of flaw formation in metal AM parts, such as porosity and deformation, is linked to the temperature inside the part during the process, called the thermal history. The thermal history is a function of the process parameters and part design.

Consequently, the first step …

Quantifying Wicking In Functionlized Surfaces, Maureen Winter, Ryan Regan, Alfred Tsubaki, Craig Zuhlke, Dennis Alexander, George Gogos

UCARE: Research Products

Wicking remains the enigmatic key factor in many research areas. From boiling in power plants, to anti-icing on plane wings, to medical instruments, to heat pipes, efficiency and safety depend on how quickly a surface becomes wet. Yet wicking remains difficult to quantify and define as a property of the surface. This experiment strives to measure the wicking property by examining the rate that a liquid can be pulled out of a container. A superhydrophilic surface is placed in contact with the liquid at the bottom of a tube so that the volume flow rate across the surface can be …

Pool Boiling Inversion On Femtosecond Laser Surface Processed 304 Stainless Steel And Its Impact On Steady-State Time Constants, Justin Costa-Greger, Alfred Tsubaki, Josh Gerdes, Mark Anderson, Craig Zuhlke, Dennis Alexander, Jeff Shield, George Gogos

UCARE: Research Products

FLSP surfaces resulting in boiling inversion require longer times to reach steady-state once inversion has occurred Boiling inversion has been shown to be the result of changing nucleation dynamics in which a large number of nucleation sites activate Increased time required to reach steady-state is linked to the rate at which these nucleation sites activate. Heat fluxes above the boiling inversion point can require up to an additional 3 hours to reach steady-state, compared to the typical 15-20 minutes reported in the literature

Computational Studies Of Thermal Properties And Desalination Performance Of Low-Dimensional Materials, Yang Hong

Department of Chemistry: Dissertations, Theses, and Student Research

During the last 30 years, microelectronic devices have been continuously designed and developed with smaller size and yet more functionalities. Today, hundreds of millions of transistors and complementary metal-oxide-semiconductor cells can be designed and integrated on a single microchip through 3D packaging and chip stacking technology. A large amount of heat will be generated in a limited space during the operation of microchips. Moreover, there is a high possibility of hot spots due to non-uniform integrated circuit design patterns as some core parts of a microchip work harder than other memory parts. This issue becomes acute as stacked microchips get …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Temperature And Stress Analysis During Tank Decanting And Refilling Process, Zhe Liu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

In the present work, an analytical expression for the temperature distribution of the cross-section of a natural gas transport tank is derived by time-matching Green’s Function method. The tank decanting process can produce a living temperature decrease inside the tank wall while the filling process can produce a large temperature increase. This behavior can cause damage to the inner layer of the tank. The damage occurs in the form of excessive stress in the wall which is combined mechanical stress and thermal stress. Therefore, thermo-elasticity analysis is another objective of the present work. A simplified mechanical model is established in …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

Design And Validation Of An Experimental Setup To Study Single Phase Heat Transfer Enhancement Of Femtosecond Laser Processed Metallic Surfaces, Sarah Jane Wallis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, a single phase flow heat transfer experimental loop was designed with the intention of studying the effects of femtosecond laser surface processing (FLSP) on metallic surfaces with the specific goal of enhancing heat transfer in compact heat exchangers currently in use by NASA. This experimental setup went through two major design iterations which are detailed in this thesis. The first iteration consisted of a counterflow fluid-to-fluid heat exchanger, which measured overall heat transfer coefficients and pressure drops, where the overall heat transfer coefficient is defined in terms of the total thermal resistance to heat transfer between …

Applications Of Femtosecond Laser Processed Metallic Surfaces: Leidenfrost Point And Thermal Stability Of Rare Earth Oxide Coatings, Anton Charles Hassebrook

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In this thesis, micro/nano structured surfaces were created through the use of Femtosecond Laser Surface Processing (FLSP). In the first part of the thesis, an experimental investigation of the effects of droplet diameters and fluid properties on the Leidenfrost temperature of polished and nano/microstructured surfaces has been carried out. Leidenfrost experiments were conducted on a stainless steel 304 polished surface and a stainless steel surface which was processed by a femtosecond laser to form Above Surface Growth (ASG) nano/microstructures. Surface preparation resulted in a root mean square roughness (R_rms) of 4.8 µm and 0.04 µm on the laser …

Models For Decanting Gaseous Fuel Tanks: Simulations With Gfssp Thermal Model, Kailash Kumar Jain Munoth

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Transport of fuel from distillation/storage plant to different parts of the world has always been challenging task for Engineers. Different methods have been proposed over the time for transporting fuel efficiently and at low cost which include Marine vessels, Pipelines, Rail Cars and Trucks. In order to transport useful amount of fuel in a reasonably sized tank, we have to liquefy it. While few fuels are easy to liquefy there are great number of fuels which liquefy only under extreme pressure/temperature conditions. Methane has a boiling point of -161.7°C at atmospheric pressure which means it has to be cooled to …

Leidenfrost Energy Barriers, James Peck, Anton Hassebrook, Craig Zuhlke, Troy P. Anderson, Dennis R. Alexander, George Gogos, Sidy Ndao

UCARE: Research Products

In this work, an “Energy Barrier” was created to control the motion of Leidenfrost droplets. This barrier was created by functionalizing a portion of a mirror-polished stainless steel 304 surface with Femtosecond Laser Surface Processing (FLSP). FLSP results in superhydrophilic, hierarchical, micro- and nanostructures which are highly wetting and thus have an increased Leidenfrost temperature. Water droplets in the film boiling state were deposited, and propelled by gravity towards the Energy Barrier interface. Room temperature droplets were deposited over a range of surface temperatures beginning with the Leidenfrost temperature of mirror-polished stainless steel 304 and culminating at the Leidenfrost temperature …

Modeling Of Methane Tank Depressurization In Cold Weather, Brittney Bridger-Burton, Kevin D. Cole

UCARE: Research Products

Non-metallic tanks are used in industry to store and transfer gasses such as methane. As the tanks are emptied, the properties of the gas change, causing heat transfer with the tank wall. When emptied while at low temperatures, liquid condensation can form and the tank lining can reach a critically low temperature, causing fracture to the tank wall. In this study, the emptying of methane in cold weather conditions from a non-metallic tank was modelled using Aspen Tech Software. A full tank of methane, at 250 bar and 288 K, was cooled to the following starting temperatures: 263, 253, 243, …

Heat Transfer Enhancement And Applications Of Femtosecond Laser Processed Metallic Surfaces, Corey M. Kruse

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, functionalized 304 stainless steel metallic surfaces were created with the use of a Femtosecond Laser Surface Processing (FLSP) technique. The laser processing technique produces self-organized micro/nanostructures on the surface. The heat transfer performance of various FLSP functionalized surfaces were characterized through pool boiling and Leidenfrost experiments. Enhancement in both the nucleate and film boiling heat transfer were observed through an increase of the critical heat flux and heat transfer coefficient as well as shifts in the Leidenfrost temperature respectively. For both experiments, a polished reference sample was used as a baseline line to compare against the …

Anisotropic Thermal Property Measurement Of Carbon-Fiber/Epoxy Composite Materials, Tian Tian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This work originated from a need for understanding heat transfer in carbon-fiber/epoxy natural-gas tanks undergoing rapid heating during refilling. The dissertation is focused on the determination of the anisotropic thermal properties of carbon-fiber/epoxy composite materials for in-plane and through-thickness directions. An effective anisotropic parameter estimation system consisting of the 3ω experimental technique and an anisotropic two-dimensional heat transfer model is developed.

In the present work, the 3ω method, an experimental technique that has been well established to evaluate the thermal properties of isotropic materials, especially thin film materials, is extended to treat the thermal properties of bulk anisotropic …

Nonequilibrium Thermodynamics Modeling Of Coupled Biochemical Cycles In Living Cells, Yaşar Demirel

Yaşar Demirel Publications

Living cells represent open, nonequilibrium, self organizing, and dissipative systems maintained with the continuous supply of outside and inside material, energy, and information flows. The energy in the form of adenosine triphosphate is utilized in biochemical cycles, transport processes, protein synthesis, reproduction, and performing other biological work. The processes in molecular and cellular biological systems are stochastic in nature with varying spatial and time scales, and bounded with conservation laws, kinetic laws, and thermodynamic constraints, which should be taken into account by any approach for modeling biological systems. In component biology, this review focuses on the modeling of enzyme kinetics …

Thermodynamically Coupled Heat And Mass Flows In A Reaction-Transport System With External Resistances, Yaşar Demirel

Yaşar Demirel Publications

Considerable work has been published on mathematically coupled nonlinear differential equations by neglecting thermodynamic coupling between heat and mass flows in reaction-transport systems. The thermodynamic coupling refers that a flow occurs without or against its primary thermodynamic driving force, which may be a gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling of thermodynamically coupled heat and mass flows of two components in a reaction-transport system with external heat and mass transfer resistances. The modeling equations are based on the linear nonequilibrium thermodynamics approach by assuming that the system is in the vicinity of global …

Modeling Of Thermodynamically Coupled Reaction-Transport Systems, Yaşar Demirel

Yaşar Demirel Publications

Nonisothermal reaction-diffusion systems control the behavior of many transport and rate processes in physical, chemical and biological systems, such as pattern formation and chemical pumps. Considerable work has been published on mathematically coupled nonlinear differential equations by neglecting thermodynamic coupling between a chemical reaction and transport processes of mass and heat. This study presents the modeling of thermodynamically coupled system of a simple elementary chemical reaction with molecular heat and mass transport. The thermodynamic coupling refers that a flow occurs without or against its primary thermodynamic driving force, which may be a gradient of temperature or chemical potential or reaction …

Thermodynamically Coupled Transport In Simple Catalytic Reactions, Yaşar Demirel

Yaşar Demirel Publications

Considerable work published on chemical reaction-diffusion systems investigates mainly mathematically coupled nonlinear differential equations. This study presents the modeling of a simple elementary chemical reaction with thermodynamically and mathematically coupled heat and mass transport with external mass and heat transfer resistances. The thermodynamic coupling refers that a flow occurs without or against its primary thermodynamic driving force, which may be a gradient of temperature or chemical potential. The modeling is based on the linear nonequilibrium thermodynamics approach and phenomenological equations by assuming that the system is in the vicinity of global equilibrium. This approach does not need detailed coupling mechanisms. …

Thermoeconomics Of Seasonal Latent Heat Storage System, Yaşar Demirel, H. Hüseyin Öztürk

Papers in Thermal Mechanics

A simple thermoeconomic analysis is performed for a seasonal latent heat storage system for heating a greenhouse. The system consists of three units that are a set of 18 packed-bed solar air heaters, a latent heat storage tank with 6,000 kg of technical grade paraffin wax as phase-changing material, and a greenhouse of 180m2. The cost rate balance for the output of a unit is used to estimate the specific cost of exergy for a yearly operation. Based on the cost rate of exergy, fixed capital investment, operating cost, and economic data, approximate cash-flow diagrams have been prepared. The systems …

Non-Isothermal Reaction-Diffusion Systems With Thermodynamically Coupled Heat And Mass Transfer, Yaşar Demirel

Papers in Analytical Chemistry

Non-isothermal reaction-diffusion (RD) systems control the behavior of many transport and rate processes in physical, chemical, and biological systems. A considerable work has been published on mathematically coupled nonlinear differential equations of RD systems by neglecting the possible thermodynamic couplings among heat and mass fluxes, and reaction velocities. Here, the thermodynamic coupling refers that a flux occurs without its primary thermodynamic driving force, which may be gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling equations of non-isothermal RD systems with coupled heat and mass fluxes excluding the coupling of chemical reactions using the linear …

Retrofit Of Distillation Columns Using Thermodynamic Analysis, Yaşar Demirel

Papers in Physical Properties

Thermodynamic analysis provides the column grand composite curves and exergy loss profiles, which are becoming readily available for a converged distillation column simulation. For example, the Aspen Plus simulator performs the thermodynamic analysis through its Column–Targeting tool for rigorous column calculations. This study uses the column grand composite curves and the exergy loss profiles obtained from Aspen Plus to assess the performance of the existing distillation columns, and reduce the costs of operation by appropriate retrofits in a methanol plant. Effectiveness of the retrofits is also assessed by means of thermodynamics and economics. The methanol plant utilizes two distillation columns …

Effect Of Gravity On Methanol Diffusion Flames Burning Within A Forced Convective Environment, V. Raghavan, G. Gogos, V. Babu, T. Sundararajan

Combustion Research at University of Nebraska-Lincoln

Effect of Gravity on Methanol Diffusion Flames Burning within a Forced Convective Environment