Heat Transfer, Combustion Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Thermal Transient Analysis Of Mahogany Wood Biomass Pyrolysis: The Role Of Zeolite Catalyst Variations On Temperature Distribution, Yusri Yusri, Widya Wijayanti, Mega Nur Sasongko

Journal of Mechanical Engineering Science and Technology (JMEST)

Biomass pyrolysis is a thermochemical process that converts waste into fuel. The use of zeolite catalysts can enhance efficiency by accelerating biomass decomposition. To demonstrate its effect, thermal simulations were conducted using ANSYS Thermal Transient to analyze temperature distribution, reaction rates, and catalyst effectiveness in the pyrolysis process. This study aims to improve thermal efficiency and temperature uniformity by analyzing the effect of 10% and 20% zeolite mixtures on heat distribution and heating rates at input temperatures of 650 K, 750 K, and 850 K, using the 2D axial symmetry method. The simulation was performed under specific boundary conditions: input …

Porous Hydrophobic Adsorbent Coatings For Carbon Dioxide Capture, Samuel Babatunde Olushola

Theses and Dissertations

This work presents the development of a porous, hydrophobic zeolite 13X coating for the separation of carbon dioxide (CO₂) from flue gas or natural gas. Zeolite 13X was combined with yeast, glucose, and sodium alginate as pore-forming agents, and with polytetrafluoroethylene (PTFE) and Polydimethylsiloxane (PDMS) as hydrophobicity-inducing agents to enhance water resistance while maintaining CO₂ access to the adsorbent. The study explored PTFE/13X mass ratios ranging from 0 to 2.33 to investigate the interplay between hydrophobicity and CO₂ uptake. The wettability of the coating was characterized by using a temporal water contact angle (WCA) measurement. Increasing …

Akron Soap Box Derby Super Kids Car, Alexis Schultz, Cooper Sites, Sean Stevenson

Williams Honors College, Honors Research Projects

This project aims to redesign the All-American Soap Box Derby Super Kids vehicle to enhance safety, accessibility, and performance while maintaining full compliance with official regulations. The Super Kids program enables children with physical and cognitive disabilities to race alongside a co-pilot, but the current vehicle design presents challenges in stability, entry/exit accessibility, and control—especially following recent regulation changes that increased vehicle speed. The redesigned car will focus on improved ergonomics, lightweight construction, and structural integrity within a $1,000 budget and a 165 lb weight limit.

An iterative engineering design process will guide the project through research, CAD modeling, FEA …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Advancing Multi-Physics Modeling For Microwave Heating: Application In Micro-Reactor Design And Optimization, Raghav Adhikari

All Theses

Microreactors are a type of small-scale chemical reactors for achieving reduced volume, improved product selectivity and higher reaction rate. It allows precise temperature control, which is crucial for sensitive chemical processes. Microreactors can be employed as key components of conducting small-scale reactions with improved reactor configuration and process efficiency. It is important to identify a localized and precise heating mechanism to trigger and control the corresponding chemical reactions.

In fact, microwave heating has gathered significant attention in recent years due to its ability to deliver efficient, rapid, and localized heating, which can accelerate reaction rates and enhances the reaction selectivity. …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Endwall Contouring For Lowering The Thermal Load And Augmenting The Turbine Efficiency, Arjun Kozhikkatil Sunil, Tide Porathoor Sunny

Makara Journal of Technology

Endwall contouring having significance in delineating ideal endwalls competent in thermal load depletion is the focus of this study. We have successfully utilized non-axisymmetric contoured endwalls to enhance turbine performance by controlling the secondary flow characteristics in a blade passage through steady-state numerical hydrodynamics. The supreme endwall pattern could lower the gross pressure loss at the design stage and is related to the size of the top-loss location being productively lowered. The selective numerical shape change using multi-objective optimization at the most prominent locations resulted in contoured endwall geometry and a considerable reduction of thermal exchange in the vane passage …

Numerical Simulation Of Laser Induced Elastic Waves In Response To Short And Ultrashort Laser Pulses., Alireza Zarei

All Dissertations

In an era of intensified market competition, the demand for cost-effective, high-quality, high-performance, and reliable products continues to rise. Meeting this demand necessitates the mass production of premium products through the integration of cutting-edge technologies and advanced materials while ensuring their integrity and safety. In this context, Nondestructive Testing (NDT) techniques emerge as indispensable tools for guaranteeing the integrity, reliability, and safety of products across diverse industries.

Various NDT techniques, including ultrasonic testing, computed tomography, thermography, and acoustic emissions, have long served as cornerstones for inspecting materials and structures. Among these, ultrasonic testing stands out as the most prevalent method, …

Thermal Performance Investigation Of Thermoelectric Cooling System With Various Hot-Side Cooling Methods, Bowo Y. Prasetyo, Parisya P. Rosulindo, Fujen Wang

Makara Journal of Technology

Thermoelectric devices have been widely used in various applications, including cooling and power generation. The potential application of thermoelectric cooling systems has been studied. However, these systems still face challenges in achieving optimal performance compared with other cooling systems. Several factors, including the hot-side cooling method, influence the performance of thermoelectric systems. This study aimed to investigate the effects of different hot-side cooling methods on the thermoelectric performance and thermal behavior of thermoelectric cooling systems. The testing methods involved the combination of the thermoelectric module with five hot-side heat exchangers, including a square heatsink, a round heatsink, a two-pipe heat …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Attrition Study Of Copper-Supplemented Iron-Based Oxygen Carrier For Chemical Looping Combustion, Neng Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Chemical looping combustion (CLC) is a promising technology that can mitigate the carbon emissions for power generation. The cost of oxygen carriers (OCs) impedes the scale up of CLC. Compared to synthetic iron-based OCs, red mud (RM), an abundant iron-based solid waste from industry, is a cost-effective choice due to its intrinsic inclusion of both inert and catalytic phases that are crucial for CLC. It was anticipated that the addition of copper oxide to RM using a mechanical mixing method that can be easily scaled up would enhance both reactivity and oxygen transport capacity (OTC), and the heat of reaction …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Entertainment 721, Mark Hendricks, Noah John, Jadon Vanyo, Chelsea Payne

Williams Honors College, Honors Research Projects

The goal of this project was to design a luxury, aesthetically pleasing entertainment system with a TV lift mechanism that could be remote controlled. The design would also include a cooling cabinet for gaming systems, a remote locking system, and additional storage. Using a morphological chart and weighted decision matrix for each subsystem key features were determined to be included in the design. Several performance benchmarks were determined to accomplish the team’s design. Almost every benchmark was successful in the build of the first prototype. Several heat calculations and FEA analyses were performed on the system to ensure the success …

Fly Ash Based Geopolymer For High Temperature And High Compressive Strength Applications In Aggressive Environment, Aaryan Manoj Nair, Akm S. Rahman

Publications and Research

Geopolymers are the results of geosynthetic reactions between aluminosilicates and strong bases. This results in chemical bonds between aluminum (Al), Silicon (Si)and oxygen (O) composing polymer rings in tetrahedral coordination. These bonds give them widespread useful applications such as high heat bearing ceramics, and base construction material whilst being far more environmentally conscious. The purpose of the experiment is to examine the effect of Silicon Carbide whisker and inorganic glass particles on thermal and mechanical properties of Geopolymers. This study will help understand the effect of various compositions and concentrations of SiO₂ in mechanical strength. In this experiment, the …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Jominy Hardenability Tester With In-Situ Heating, Luke Allen

Williams Honors College, Honors Research Projects

This project centers on building a Jominy Hardenability tester with In-Situ heating for the manufacturing lab at the University of Akron. A new process and setup will be designed using engineering concepts in order to make the testing more efficient and safer for the teaching and testing of metal hardness. The current Jominy testing setup has efficiency issues within the transfer of specimen from induction heater to testing rig. Our design will simplify the design by creating a test rig that removes the traveling aspect of the specimen which will limit the amount of premature cooling done and will be …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

An Evaluation Of Induction Heating In Healthcare Food Industry, Barrett Alexander Hampton

Masters Theses & Specialist Projects

This thesis addresses the problem healthcare facilities are having in maintaining proper food temperatures while transporting meals to patients after food has left the kitchen area. Induction heat has been a known method for generating heat for many years. The commercial food industry currently uses this technology, which is beginning to appear in the residential sector as well because of developments made by manufacturers. This study focuses on the top commercial brand models of induction heaters and the supporting materials currently used to create heat sources to maintain food temperatures in hospitals and long term care facilities.

The research in …

Heating Element Including Carbon Nanotube (Cnt) Layer, Santhosh Kumar Loganathan, Virginie Rollin, Daewon Kim

Publications

Apparatus , materials , and techniques and techniques herein can include providing a deposited layer comprising a com posite material including carbon nanotubes ( CNTs ) . Accord ing to various examples , the composite can be applied to a substrate such as using a solution containing CNTs and other constituents such as sulfur . The solution can be spray applied to a substrate , or spin - coated upon a substrate , such as to provide a uniform , conductive , and optically - transpar ent film layer . In one application , such a film layer can be …

Suborbital Spaceflight: A Student Team’S Plan To Send A Rocket To Space, Bryce Chanes, William Carpenter, Julio Benavides, Matthew Haslam, Brenda Haven

Aviation / Aeronautics / Aerospace International Research Conference

The Eagle Space Flight Team was created with the goal of becoming the first undergraduate team to design, build, and launch a rocket capable of suborbital spaceflight. In order to achieve this goal, the team will have to design a rocket capable of atmospheric flight at speeds over Mach 5 and launch it on one of the largest amateur rocket motors ever made. Over the next three years, the team will progress towards accomplishing this feat through a series of incremental test flights. Before the space flight, the team will build three sub-scale rockets designed to reach altitudes of 30,000’, …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Transient Thermoelectric Supercooling: Isosceles Current Pulses From A Response Surface Perspective And The Performance Effects Of Pulse Cooling A Heat Generating Mass, Alfred Piggott

Dissertations, Master's Theses and Master's Reports

With increased public interest in protecting the environment, scientists and engineers aim to improve energy conversion efficiency. Thermoelectrics offer many advantages as thermal management technology. When compared to vapor compression refrigeration, above approximately 200 to 600 watts, cost in dollars per watt as well as COP are not advantageous for thermoelectrics. The goal of this work was to determine if optimized pulse supercooling operation could improve cooling capacity or efficiency of a thermoelectric device. The basis of this research is a thermal-electrical analogy based modeling study using SPICE. Two models were developed. The first model, a standalone thermocouple with no …

Numerical Characterization Of The Hydrodynamics And Thermal Behavior Of Air Flow In A "Flex-Duct" Air Distribution System, Samad Gharehdaghi, Samir Moujaes

College of Engineering: Graduate Celebration Programs

The aim of this research paper is to compute the hydrodynamic and heat transfer characteristics of the air flow inside a flexible duct used for residential/small commercial buildings. Various new information which manufacturers do not provide usually are produced numerically among which heat transfer coefficient, needed for estimating heat loss, is a principal one. Circulation zones in depressions are found to exist. It is shown that these regions act as an insulator and decrease the heat loss along the duct. The results show that fully developed conditions exist much earlier with regard to the inlet for both hydrodynamic and thermal …

Numerical Modeling Of High Temperature Bayonet Heat Exchanger And Decomposer For Decomposition Of Sulfur Trioxide, Vijaisri Nagarajan, Yitung Chen, Tzu-Chen Hung, Qiuwang Wang, Valery Ponyavin

College of Engineering: Graduate Celebration Programs

Motivation

• Hydrogen is an attractive energy carrier in the future energy technology.

• Hydrogen is produced from splitting of water through various process namely electrolysis, photo-electrolysis, photo-biological production and thermochemical water-splitting.

• The aim of this study is to numerically investigate fluid flow, heat transfer and chemical reaction in bayonet high temperature heat exchanger and decomposer.

• Parametric studies are performed to achieve maximum decomposition with less pressure drop.

Design, Reconstruction And Evaluation Of A Dynamometer For Quarter Scale, Samuel Sanchez

BioResource and Agricultural Engineering

This project discusses the design, reconstruction, and evaluation of a dynamometer. A new test stand for the Quarter Scale team would improve the testing of the engines and the Continuously Variable Transmission (CVT). All the readings will be done electronically in order to provide the most accurate data collection. The dynamometer will be a closed hydraulic system for ease of use. This system will be able to test all of Quarter Scale engines. The data collected will be used to determine which engines are in the best condition, and which may need to be fixed. With the new design, the …

Ir-Hot Gas Heat Source For Automated Tow Placement, Ray Walton Grenoble

Mechanical & Aerospace Engineering Theses & Dissertations

A series of five experiments on the NASA Langley automated tow placement robot revealed stagnation of gas flow in the nip region. Since the torches could not heat effectively in the nip region, the roller temperature was the dominant influence on interlaminar bond strength. The roller temperatures required for high bond strength caused resin and fiber on the panel top surface to adhere to the compaction roller. Resin and fiber was pulled from the panel surface and wrapped around the roller, which was a severe processing problem. A supplemental radiant heat source was designed to permit reductions in roller temperature. …

Design Of A Combustion System Simulating Waste Heat Recovery From Diesel Engine Exhaust Gases, Nikolaos Papadopoulos

Mechanical & Aerospace Engineering Theses & Dissertations

A forced-draft laboratory combustion system simulating diesel engine exhaust gas volume flow rate and temperature conditions for waste energy recovery is analyzed and discussed. The system consists of a fan which supplies the air. The slightly compressed air is then ducted through a combustor where it is heated, and then to an air-quencher where it is cooled to a desired temperature. Finally, the air is sent through a heat exchanger, after a diffuser process, for waste heat recovery.

A gas dynamic analysis has been performed for each component part as well as a parametric study via a computer program in …

Australian Spark Arrester Tests : Spark Arrester For International B-250, W. F. Baillie, G. H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

FORMAL tests on spark arresters are conducted by The Tractor Testing Committee at the Testing Station, Werribee, on behalf of those companies concerned with tractors, engines or spark arresters who wish to have these equipments tested.