Energy Systems Commons^™

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Load Flow And Fault Performance Evaluation Of Interconnected Minigrids In Uganda Using Digsilent Powerfactory, Prossy Mutesi, Santos Kihwele, Emmanuel Matee

Tanzania Journal of Engineering and Technology (TJET)

The increasing demand for decentralized, reliable electricity in rural Sub-Saharan Africa has catalyzed the deployment of minigrids as an intermediate electrification strategy. This study investigates two solar photovoltaic (PV) mini-grids: Kyamugarura and Kanyegaramire, located in western Uganda, approximately 3km apart. Each mini grid initially consisted of 13 kW installed photovoltaic (PV) capacity, supplying power to households and small businesses. Due to rising demand and regular evening blackouts, both mini-grids are being upgraded to 57 kWp each. The integration of these upgraded systems into the national utility grid is proposed and simulated to evaluate performance improvements under two medium-voltage interconnection options: …

Hybrid Solar - Coal Thermal Energy System For Industrial Process Heat At Sayona Drinks Limited In Tanzania, Santos Kihwele, Elisha D. Bitesigirwe

Tanzania Journal of Engineering and Technology (TJET)

Over the past two decades, global efforts to mitigate pollution from conventional energy sources have intensified, with coal remaining a major contributor to carbon emissions. While fossil fuels cannot be eliminated from thermal generation in manufacturing industries, particularly in middle‑income countries such as Tanzania, they continue to dominate as the primary energy source. Industries including food and beverage, paper, textile, paints, chemicals, and pharmaceuticals require substantial thermal energy for heating and drying, and typically rely on coal and natural gas.This study introduces a unique application of a parabolic trough solar thermal system with integrated thermal energy storage, specifically tailored to …

Optimization Of Bio-Briquettes Production From Cassava Stems Co-Blended With Sisal Bole Bagasse Using Response Surface Methodology, Agnes Nshoma Msobi, Neema O. Msuya, Kando Khalifa Janga

Tanzania Journal of Science

This research aimed at producing bio-briquettes from cassava stems and sisal bole bagasse as an alternative source of cooking energy. A Response Surface Methodology (RSM) with Face - Centered Central Composite Design (FCCCD) featured a multi-objective optimization of the effect of the production parameters, focusing on maximizing char yield and Higher Heating Value (HHV) of the produced briquette while minimizing carbonization temperature and residence time. The findings showed that bio-briquettes produced at the lowest temperature (250 ℃) and residence time (30 min) and the blending ratio of 75% by 25% had the highest char yield of 76.92% and HHV of …

Load Profile Analysis And Forecasting For Rural Mini Grids In Uganda, Prossy Mutesi, Santos L. Kihwele, Emmanuel S. Matee

Tanzania Journal of Science

Accurate load forecasting is essential for the reliable and cost-effective operation of rural mini grids, where constrained generation capacity and high penetration of renewable energy resources require well-informed operational decisions. This study examines electricity demand characteristics and forecasting performance for the Buzaami and Ssenyondo mini grids in Uganda, with particular focus on diurnal load profiles, peak demand behavior, and seasonal variability. 2022 operational data show extended peak demand from early morning to late evening, driven by socio-economic activities that strain resource scheduling and reliability management. To address these challenges, the study evaluates and compares Long Short-Term Memory (LSTM) networks, fuzzy …

Techno-Economic Analysis Of Hybrid Systems As A Solution For Electricity Supply During The Dry Season At The Bakaru Run-Of-River Hydropower Plant, Zamharir Aditya Febri, Mohammad Akita Indianto, Sheila Tobing

Journal of Materials Exploration and Findings

Within the South Sulawesi power system (Sulbagsel), the Bakaru Hydro Power Plant serves as a key facility expected to provide consistent and reliable electricity supply. However, since the Bakaru plant operates under a Run of River scheme, its energy output is highly dependent on river discharge rates. In 2024, a significant decrease in water flow was recorded between August and October, which led to a drastic reduction in power generation. To address this challenge, a hybrid energy system is proposed to ensure continuous load coverage, particularly during the dry season. The optimal configuration of this hybrid system was modeled and …

A Review Of Energy Storage Technologies With Hydro Energy System Design For Off-Grid Electricity, Daniel H. Ngoma, Banet L. Masenga

Tanzania Journal of Engineering and Technology (TJET)

Many renewable energy sources such hydropower—particularly small-scale run-of-river and micro-hydro—offers reliable, low-cost generation. However, their inherent intermittency (due to seasonal flow variations) and inability to instantly match demand necessitate integrated energy storage to ensure a stable, continuous power supply. This review synthesizes contemporary energy storage technologies in the context of their integration with off-grid hydro energy system design.

The study examine a spectrum of storage solutions, evaluating their technical characteristics, costs, and suitability for hybrid hydro applications. Pumped Hydro Storage (PHS), while highly efficient and large-scale, is often geographically constrained and capital-intensive for small off-grid projects. Battery Energy Storage Systems …

Preliminary Study Of Circular Lithium-Ion Battery Thermal Management System With Intermittent Cooling, Muhammad Luthfi, Leo Van Gunawan, Yudhy Kurniawan, Sabda Ikhwal Rahmatullah, Alfarikh Muhammad Daen

Journal of Mechanical Engineering Science and Technology (JMEST)

The active battery thermal management system is important to maintain the lithium-ion battery temperature within the optimum and safe range. However, current research has not considered the potential for excessive energy consumption due to the continuous operation of a fluid flow source, such as a fan. This research aims to investigate the effect of a novel approach called intermittent cooling on the cooling efficacy and energy consumption of the circular-configuration BTMS. Both transient computational fluid dynamic simulation and experiment were conducted in this work with 30 pieces of 18650 Lithium-Ion batteries positioned in a staggered circular configuration. From the result, …

Performance Analysis Of A Converted Electric Underbone Motorcycle: A Combined Dynamometer And Road Test Approach, Dhimas Oki Permata Aji, Sigit Suwarto, Yunus Ari Rokhim

Journal of Mechanical Engineering Science and Technology (JMEST)

In developing countries, converting traditional underbone motorcycles to electric vehicles transforms sustainable transportation from a theoretical concept to a practical implementation. This paper describes the design and operational performance evaluation of an electric underbone motorcycle conversion system that integrates a 2.0 kW, 72 V BLDC motor and a 72 V, 20 Ah lithium-ion battery pack. Compared to previous studies, this paper combines, for the first time, both dynamometer and road tests as the basis for a comprehensive performance assessment of low-cost motorcycle conversion. The dynamometer test was conducted under laboratory conditions to evaluate the test system for torque, power output, …

Experimental Study Of Dimpled Serpentine Reactors For Hydrogen Production Via Methanol Steam Reforming, Mohamed I. Zeid, Mahmoud A. Shouman, Osama Abdelrehim, Ahmed M. Hamed

Mansoura Engineering Journal

Hydrogen is widely regarded as a clean energy carrier, with methanol steam reforming (MSR) emerging as a promising route for portable and on-board applications due to its favorable operating conditions and high hydrogen yield. Reactor geometry plays a decisive role in hydrogen productivity, pressure drop, and energy efficiency, yet the balance among these factors remains insufficiently addressed. In this study, three serpentine aluminum microreactors: a plain serpentine reactor (PSR), a rhombusdimple reactor (RDR), and a hemispherical-dimple reactor (HDR) were fabricated and coated with a copper (II) oxide, zinc oxide, aluminum oxide (CuO/ZnO/Al₂O₃) catalyst to experimentally investigate the effect of dimple …

Effect Of Inter Electrode Distance On Electrochemical Mineralization Of Calcium Carbonate In Mildly Acidic Environments, Irene Walker, Ivy Wu, Steven Decaluwe, Robert Bell, Kerry Rippy

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

The effect of inter electrode distance (IED) on electrochemical mineralization in a parallel plate cell with a stainless-steel working electrode is presented. Three IEDs were tested, 6.5 mm, 15.5 mm, and 22.0 mm, for their water reduction effectiveness to create a region of local alkalinity that stimulates calcium carbonate precipitation in mildly acidic conditions. Chronoamperometry at -1.6 V for 30 minutes with ex-situ optical microscopy and scanning electron microscopy (SEM) were used. At the smallest IEDs, crystal clusters formed in growth-favored regimes as compared to the largest IED, where nucleation dominated, leading to encasement of the SS mesh. Rapid precipitation …

Control Of Ferroelectric And Dielectric Properties Of Undoped, Fe, And Nb-Doped Single-Crystalline (001) Oriented Pb (Zr0.5ti0.5) O3 Thin Films, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

While several factors that influence the properties of ferroelectric devices have been extensively studied in bulk ceramics and polycrystalline thin films, limited is known about the same on single crystalline thin films which have great potential in memory and energy applications. This knowledge gap is largely due to the limited availability of substrates with lattice parameters suitable for supporting high-quality epitaxial growth. In this study, undoped, Fe-doped, and Nb-doped (001)-oriented Pb(Zr₀.₅Ti₀.₅)O₃ thin films were deposited using pulsed laser deposition, each with a SrRuO₃ bottom electrode and a PrScO₃ substrate. The doping concentration used is 1% for both Fe and Nb. …

Techno-Economic Analysis Of Hybrid Pv-Wind-Diesel Generator Swarm Grid For Rural Electrification In Tanzania, Ibrahim Mwammenywa

Tanzania Journal of Engineering and Technology (TJET)

Remote, rural, and off-grid communities, particularly in Sub-Saharan Africa (SSA), face significant challenges in securing reliable and affordable electricity. While solutions such as solar home systems (SHSs) and diesel generators (DGs) have been adopted by some individuals, their deployment is often not optimized to meet the full load demand. This study addresses this challenge by proposing a hybrid swarm grid (HSG) design that integrates photovoltaic (PV), wind energy, and diesel generators (DGs). Utilizing MATLAB/Simulink and HOMER, the HSG is modeled and optimized for a typical SSA village, incorporating real-world variables such as load demand profiles, solar irradiance, and wind patterns. …

Adoption Of Agrivoltaics In Developing Countries: A Review On Challenges, Opportunities And Future Prospects, Abdi J. Athumani, Pater Makolo

Tanzania Journal of Engineering and Technology (TJET)

This paper provides a review of agrivoltaics technology and how it has been applicable in developing countries, including African countries. Agrivoltaics, the integration of agricultural production with photovoltaic energy generation, offers promising solutions to water- energy-food nexus in developing countries. This technology offers the dual benefit of increasing agricultural productivity while generating clean energy, which is very important for regions facing frequent electricity shortages and declining agricultural yields due to climate change. However, despite its potential, the adoption of agrivoltaics in developing nations remains limited in comparison to developed countries due to financial, technical and policy constraints. This paper explores …

Optimal Location And Sizing Of Facts Devices To Improve Voltage Profiles On A 132 Kv Mwanza-Musoma-Nyamongo Transmission Line, Peter Makolo

Tanzania Journal of Engineering and Technology (TJET)

Recently, utility companies have desired to supply quality, stable and reliable power to customers, and ensure they meet the demand. Flexible AC Transmission Systems (FACTS) dynamic compensator devices such as Static Synchronous Compensator (STATCOM), Static VAr Compensator (SVC) and Unified Power Flow Controller (UPFC) are an impeccable choice, however, cost is one of the limiting factors following these technologies. In addition, using FACTS devices in the system requires a detailed steady state, dynamic and optimisation analysis to effectively meet the purpose and ensure reduced cost. This paper proposes using an optimised FACTS device to improve voltage profile, power transfer, system …

Investigating The Harmonic Content Of A Pwm Inverter With Varying Modulation Index, Peter Makolo

Tanzania Journal of Engineering and Technology (TJET)

Photovoltaic energy is a clean and endless vital renewable energy. In order to generate electricity from solar energy an inverter is required to transform the direct current into alternating current. Also, with the emerging of new ultra-high voltage direct current transmission technology, the rectification and inverters play a great role. Most three-phase two-level inverters draw harmonics that cause heat dissipation, waveform distortions hence affect the electrical loads. Knowing that Total Harmonic Distortion content of voltage source inverter is important and must be within the allowable range. Several schemes are suggested to mitigate the distortion in order to produce as much …

Design And Implementation Of A Smart Solar Tracking System Using Hydraulic Actuation, Bassem Nashaat Zakher, Mahmoud M. Ramzi, Kirolos A. Amin

Journal of Engineering Research

This research presents the design and implementation of a smart single-axis solar tracking system that introduces a novel integration of hydraulic actuation with minimalistic sensor control. Unlike traditional trackers that rely on multiple light sensors and complex mechanical setups, the proposed system uses a simplified control mechanism driven by a single-point light detection strategy to maintain panel alignment with the sun. The core innovation lies in replacing motor-driven tracking mechanisms with a hydraulic actuator, offering smoother, more durable movement with reduced maintenance. Additionally, the system integrates smart monitoring via Arduino, enabling real-time data processing and decision-making without relying on costly …

Design Of A 10-Ton Capacity Solar-Powered Cold Storage At The Cituis Fish Auction Site, Tangerang, Banten, Indonesia, Wardi Wardi, Muhammad Arif Budiyanto

Journal of Materials Exploration and Findings

This study presents the design of a 10-ton capacity solar-powered cold storage system for the Cituis Fish Auction Site (TPI) in Tangerang, Indonesia, as a sustainable solution to support the coastal fisheries sector. The system comprises two temperature zones: an anteroom at 5°C and a freezer room at -30°C, both integrated with a hybrid system utilizing solar panels and batteries. The total power consumption of the cooling system reaches 27.51 kW. The simulation results, obtained using HOMER Pro software, indicate that the hybrid PV system can reduce CO₂ emissions by up to 16,754 kg per year. From an economic …

Mitigation Of Voltage Disturbances In Industrial Power Distribution Networks Using Dynamic Voltage Restorers, Aviti T. Mushi

Tanzania Journal of Engineering and Technology (TJET)

Most electrical and electronic equipment in industries require high-quality power to function efficiently. Nonetheless, voltage sags and swells are pressing concerns and prone to directly impact the economy of industrial customers. One such customer embattled with these problems is Mbeya Cement Company Limited (MCC) located in Mbeya, Tanzania. These issues mainly are caused by upstream faults and switching operations. One way to address these is by utilizing the voltage injection method, which employs a power device known as a dynamic voltage restorer (DVR). In this paper, the voltage sags and swells of balanced three-phase, unbalanced double-line and single-line to ground …

Fuzzy Logic-Based Decision Support System For Adoption Of Industry 4.0 Predictive Maintenance By Manufacturing Industries, Fred E. Peter

Tanzania Journal of Engineering and Technology (TJET)

In the context of Industry 4.0, predictive maintenance enhances operational efficiency by optimizing processes, minimizing downtime, and improving cost-effectiveness. However, implementing predictive maintenance requires a systematic approach due to its complexity. This study collected expert input from 15 food and beverage manufacturing industries located in Dar es Salaam, Tanzania, using a purposive sampling technique. Six representatives were selected from each industry, and their opinions were analyzed using MATLAB 7.6 through a fuzzy logic inference system. The analysis focused on key factors influencing Industry 4.0 technology adoption for predictive maintenance, including adoption intention (strategic decision, equipment data, perceived benefit) and perceived …

Thermal Energy Storage System Using Silica Sand As Heat Storage Medium: Simulation Of Geita Gold Mine, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

Currently, Geita Gold Mine (GGM) relies on electrical energy from the national grid and diesel power generators to generate electricity for various industrial applications. The plant currently spends a large amount of money on generating power from diesel generators. The total annual cost of power generation from diesel generators including lubricants is USD 56,057,990. The total annual fuel cost is USD 53,531,805 for a total of 54,985,473 liters per year. Most of the power generated by the generators is consumed in the industrial thermal processes. Thermal energy applications at the plant are thermal drying of the extracted ores to remove …

Wet Gas Metering Performance Using Conventional Flow Measurement Devices, Vitali Mwinyi

Tanzania Journal of Engineering and Technology (TJET)

The demand for and production of natural wet gas from wells has significantly risen in recent years. Although natural gas liquids hold substantial value in the oil and gas market, their presence in wet gas adversely affects gas metering, leading to overreading during measurement. A comprehensive study has been undertaken to formulate and enhance correlations for rectifying overreading in wet gas metering. Nevertheless, most current correlations are designed for horizontal configurations of traditional meters. Mitigating this constraint is crucial to consider the impact of gravity on pressure loss in vertically oriented systems. This study seeks to evaluate the efficacy of …

Energy Optimal Coverage Motion Trajectory Generation Using A Fourth-Order Motion Profile, Mathias Halinga

Tanzania Journal of Engineering and Technology (TJET)

Industrial machines are widely used in manufacturing sector to manufacture several products to meet customer demands. Most of these industries runs all the time throughout a day leading to high operating cost. To cut costs and satisfy customer demand for precise products, industrial machines’ motion generation is important in improving machine motion precision while using less energy. This study presents a coverage motion energy optimization which is generated by linear interpolation of each segment described by the fourth-order motion profile. The phase changes in the profile are attained with continuity of machine kinematic limits jerk, acceleration, and velocity, which are …

The Impacts Of Renewable Energy Sources: A Review On Grid Inertia And Frequency Regulation, Sospeter Gabriel

Tanzania Journal of Engineering and Technology (TJET)

The power system is gradually transitioning into low inertia due to integrating substantial intermittency quantity of converter-based renewable energy sources, such as wind and photovoltaic power, into the current power grid network. This integration presents significant inertia and frequency control challenges to the network as a result of a decrease in the percentage of synchronous generators. Moreover, faster frequency deviations are posed by the mismatch between the supply and demand during contingencies, which creates difficulties in preserving the frequency stability of the power system. This research explores the impacts of renewable energy sources (RESs) on grid inertia and frequency management …

Analysis Of An Improved Reliability Dual-Buck Structured Three-Level Flying Capacitor Inverter, Almachius Kahwa Dr.

Tanzania Journal of Engineering and Technology (TJET)

With the increased demand for high-reliability power converters in the electric drive-train and propulsion systems, the efforts to design and analyze converters with high fault tolerance have become apparent. Among the emerging trends to improve the reliability of power converters is the incorporation of dual-buck (DB) structures in traditional converter topologies. Thus, this paper studies a single-phase dual-buck structured three-level flying capacitor (FC) inverter. The dual-buck flying capacitor (DBFC) inverter was constructed in such a way as to suppress the shoot-through problems that may occur because of the switching mismatch and gate driver delay, as exhibited in the traditional FC …

Calibration Of Measurement Tools In The Experimental Test Rig For Hydropower Performance Evaluation, Ombeni J. Mdee

Tanzania Journal of Engineering and Technology (TJET)

The demonstration of a typical hydropower plant requires the development of a test rig with the installation of tools to measure the performance parameters. The measurement tools require a calibration process to improve the quality of recorded data. This study involved the calibration of traditional and automated measurement tools connected to the hydropower test rig through an Arduino microprocessor. The automated measurement tools included a pressure transducer, flow meter, digital tachometer, and torque transducer, while traditional measurement tools, including a pressure gauge, concrete water tank, contact tachometer, and force lever arm balance, were connected in the same test rig during …

Review On Gas-To-Liquids Conversion Technology: Lessons From Case Studies And Potential Strategies For Implementation In Tanzania, Joseph H. Kihedu

Tanzania Journal of Engineering and Technology (TJET)

This review paper explores the transformative potential of Gas-to- Liquids (GTL) technology for harnessing Tanzania's vast natural gas resources. With significant discoveries of natural gas reserves totalling up to 57 Tcf in fields such as Songosongo, Mnazi Bay, Block 1, 2, 3 and 4. Tanzania is positioned to leverage GTL technology to convert these resources into high-value liquid fuels like gasoline, diesel and naphtha. Review of GTL process, its products and applications has been done. By analysing successful GTL projects globally and drawing lessons applicable to Tanzania, this paper provides strategic recommendations for policymakers and stakeholders to foster GTL development. …

A Review Of Lithium-Ion Battery Capacity Fade Deceleration At Power Fluctuations In Renewable Energy Systems, Isaac Gwayi

Tanzania Journal of Engineering and Technology (TJET)

Application of lithium-ion (Li-ion) batteries to store energy in renewable energy systems (RESs) is increasing due to their promising properties. Therefore, it is crucial to understand aging behaviours of Li-ion battery during RES life time as this directly affects cost of energy. Li-ion battery aging can be categorised into calendar aging and cycle aging. Calendar aging depends mainly on temperature and state of charge (SoC). In addition to temperature and SoC, cycle aging depends also on charge and discharge current rates and cut-off voltages. Higher current rates lead to faster Li-ion battery aging. It is necessary to identify appropriate battery …

Assessment Of Maintenance Performance Level Of Selected Hydropower Plants In Tanzania, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

Despite significant progress in increasing electricity access to over 78%, electricity reliability in Tanzania remains a concern, with frequent power outages reported. Maintenance issues in hydropower plants have been identified as a critical factor contributing to this problem. However, the specific maintenance performance levels have not been fully assessed. This study conducts a comprehensive evaluation of the maintenance performance of four key hydropower plants: Kidatu (204 MW), Kihansi (180 MW), Mtera (80 MW), and New Pangani Falls (68 MW). Data collected from staff surveys and maintenance records between 2018 and 2022 were used in the study. Although staff demonstrated a …

Root Cause Analysis Of Performance Degradation For An Xyz Thermal Power Plant In Tanzania, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Thermal power plants in Tanzania have been experiencing performance degradation, typically arising from component and subsystem failures, which contribute to power system instability and unreliability. This paper presents a case study of the root causes of performance degradation of an XYZ thermal power plant. The study was conducted by reviewing plant documentations, including maintenance and operational data logbooks, and by standardising the approach through the adoption of ISO 14224:2016 for maintenance and reliability data exchange. Data evaluation was carried out using principal component analysis and scree plot analytical techniques to enhance the depth and accuracy of root cause identification. Additionally, …