Energy Systems Commons^™

Modelling Of Biomass Gasification Integrated With A Solid Oxide Fuel Cell System, Wayne Doherty

Doctoral

Biomass is of major interest as a renewable energy source in the context of climate change and energy security. Traditional biomass conversion technologies achieve low electrical efficiencies. Biomass gasification (BG) coupled with fuel cells offer higher efficiencies. Gasification is a process in which a carbonaceous fuel is converted to a combustible gas. It occurs when a controlled amount of oxidant is reacted at high temperatures with available carbon in a fuel within a gasifier. Two technologies (circulating fluidised bed air gasification and dual fluidised bed steam gasification) were modelled. Solid oxide fuel cells (SOFCs) are well suited to integration with …

Aspen Plus Simulation Of Biomass Gasification In A Steam Blown Dual Fluidised Bed, Wayne Doherty, Anthony Reynolds, David Kennedy

Book/Book Chapters

The efficient utilisation of biomass resources is of utmost importance. Biomass gasification offers much higher efficiencies than combustion. Gasification is a process in which a fuel is converted to a combustible gas (syngas). A dual fluidised bed gasifier known as the fast internally circulating fluidised bed (FICFB) was selected. It has been demonstrated at industrial scale and data is readily available for model validation. An Aspen Plus model was developed to simulate the FICFB gasifier. The model is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it. The model has been validated and …

Heating Effects Through Harmonic Distortion On Electric Cables In The Built Environment, Kevin O'Connell

Doctoral

Under ideal circumstances, electric power supply voltage and current waveforms should be sinusoidal. However, this is very seldom the case in the built environment, due to the proliferation of non-linear loads. Examples of non-linear loads are those containing switched mode power supplies, reactors and electronic rectifiers/inverters. Common devices such as personal computers, fluorescent lighting, electric motors, variable speed drives, transformers and reactors and virtually all other electronic equipment are examples of non-linear loads. Non-linear loads are the norm in the built environment rather than the exception. Such loads produce complex current and voltage waves and simple spectral analysis of these …

The Effects Of Physical Activity On Greenhouse Gas Emissions For Common Transport Modes In European Countries, Aidan Duffy, Robert Crawford

Articles

This paper applies a life cycle methodology to estimate activity-related contributions of transport modes to GHG emissions. The methodology uses national input-output tables, environmental accounts, household budget data and nutritional data to derive food-sector GHG coefficients of consumption for ten European countries. The food energy requirements for each mode of transport are estimated taking account of the modal activity level and energy requirements. Walking, cycling, driving and bus travel are considered. Typical national food energy-related emissions for walking, cycling, and driving ranged from 25.6 - 77.3 gCO2-eq/pass.km, 10.4 - 31.4 gCO2-eq/pass.km and 1.7 - 5.2 gCO2-eq/pass.km; passenger transport was found …

State Of The Irish Housing Stock - Modelling The Heat Losses Of Ireland’S Existing Detached Rural Housing Stock & Estimating The Benefit Of Thermal Retrofit Measures On This Stock, Ciara Ahern, Philip Griffiths, Micheal O'Flaherty

Articles

Ireland’s housing stock has been identified as being amongst the least energy efficient in Northern Europe. Consequently, atmospheric emissions are greater than necessary. Government funded schemes have been introduced to incentivise the uptake of thermal retrofit measures in the domestic Irish market. A study of Ireland’s housing highlights the dominance of detached houses (43%), 72% of which are rurally located and are predominantly heated with fuel oil. This paper investigates the economic and carbon case for thermal retrofit measures to the existing detached, oil centrally heated, rural housing stock. The study found the case for energy efficiency measures to be …

Transient And Quasi-Steady Thermal Behaviour Of A Building Envelope Due To Retrofitted Cavity Wall And Ceiling Insulation, Aimee Byrne, Gerard Byrne, Anna Davies, Anthony Robinson

Articles

Accurate understanding of the thermal behaviour of building components is essential for predicting heat-ing or cooling needs and facilitates the implementation of more successful energy saving strategies and retrofits. This paper focuses on a specific measure commonly introduced through the residential energy efficiency retrofit programmes in Ireland–insulation. Traditionally, assessments of the performance of building envelopes have been based on assumed thermal resistances of the materials involved, labora-tory tests and computer modelling. The aim of the present work is to investigate the in situ thermal behaviour of a case study building and its components under transient and quasi-steady environmental conditions, comparing …

Development And Implementation Of A Simplified Residential Energy Asset Rating Model, Daire Reilly, Aidan Duffy, David Willis, Michael Conlon

Other resources

In accordance with national and European policies, the provision of financial assistance to residential energy consumers has led to a greater awareness of and interest in energy retrofit technologies. However, at present Irish energy consumers have no appropriate advice on the future performance of retrofit options available to them. This is a significant limitation to decision making and technology uptake, since this group need to know whether their investment is likely to be worthwhile.

The asset rating methodology developed for the certification of energy performance of buildings is the current industry standard of prediction of energy demand and post retrofit …

A Simulation Analysis Of Photovoltaic Ac Module Integrated Converters In Parallel, Under Controlled Edge Shading Conditions, Lynette O'Callaghan, Mick Mckeever, Brian Norton

Conference Papers

A DC and AC power simulation comparison of: a Photovoltaic (PV) array with a modular, parallel, AC converter configuration; and a series, string configuration with a central AC converter, is presented. The systems are simulated using a comprehensive range of edge shading scenarios and irradiance conditions. Power control and transformation circuitry must be designed for shade and module mismatch tolerance to prevent over-proportional power to shade losses, as average losses from Building Integrated PV (BIPV) systems are approximately 20 to 25%, due to shade, mismatch, differences in orientation and inclination, and temperature effects. 59.4% of the simulations showed gains in …

Technical Note: Friction Factor Diagrams For Pipe Flow, Jim Mcgovern

Articles

This technical note describes diagrams of friction factor for pipe flow that have been prepared using, mainly, the equations that Lewis Moody used to prepare his famous diagram in 1944. The preparation of the new diagrams was prompted by the need for vector graphics versions that could be used for teaching purposes and that could be distributed freely to students and others under a Creative Commons Attribution-Share-Alike license. Using a structure very similar to that of Moody's diagram, variants with the Darcy friction factor and the Fanning friction factor have been prepared. In addition, variants have been prepared that include …

Analyse Du Comportement Réel Et De L'Optimisation Structurelle Des Cycles De Turbines À Gaz, Alexandru Dobrovicescu, Michel Feidt, Lavinia Grosu, Jim Mcgovern, Georgiana Tirca-Dragomirescu

Conference Papers

L’article présente une étude comparative, basée sur l’analyse exégétique, de l’effet de non prise en considération du comportement réel de l’agent thermique et de l’utilisation des modèles simplifiés pour calculer les performances des cycles de turbines à gaz avec et sans récupération de chaleur. Un intérêt spécial a été réservé au processus de combustion et au transfert de chaleur dans le préchauffeur d’air. La variation des destructions et des pertes d’exergie par rapport à la variation des paramètres fonctionnels est présentée.

Some Experiences, Thoughts, Ideas And Open Questions Relating To Applied Thermodynamics, Jim Mcgovern

Articles

In this paper I present some of my thoughts and experiences relating to 'applied thermodynamics' over my career so far. I explain my interest in thermodynamics, describe some topics I have worked on, point out some questions that appear still to be open and outline some ideas for work that could be done. I describe how I was inspired to pursue the area of applied thermodynamics, with reference to a glass, opposed-piston internal combustion engine. I put my heat pump research in the late 1970s briefly into today's context. Some of my research has been in relation to compressors, which …

Computer Simulation Of A Biomass Gasification-Solid Oxide Fuel Cell Power System Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

The operation and performance of a solid oxide fuel cell (SOFC) stack on biomass syn-gas from a biomass gasification combined heat and power (CHP) plant is investigated. The objective of this work is to develop a model of a biomass-SOFC system capable of predicting performance under diverse operating conditions. The tubular SOFC technology is selected. The SOFC stack model, equilibrium type based on Gibbs free energy minimisation, is developed using Aspen Plus. The model performs heat and mass balances and considers ohmic, activation and concentration losses for the voltage calculation. The model is validated against data available in the literature …

Thermodynamic Optimisation Of The Otto / Stirling Combined Cycle, Barry Cullen, Michel Feidt, Jim Mcgovern, Stoian Petrescu

Conference Papers

Combined cycle systems are an established method for increasing primary energy efficiency of power generation systems. Some ongoing research is concerned with investigating the novel combined cycle system involving the Otto and Stirling thermodynamic cycles. The Otto cycle is to act as the topping cycle, with the Stirling cycle acting to recover heat from the exhaust for the purpose of additional power generation. The present work investigates the thermodynamic optimisation of the combined cycle system for the case of the engines operating under two imposed parametric constraints: 1) imposed heat addition to the Otto cycle, and 2) imposed maximum cycle …

Investigation Into The Possible Benefits Of A Refrigeration Based Intercooling System, Ronan Kierans, Jim Mcgovern

Conference Papers

This paper describes findings from analysis and simulation in relation to the possible benefits of applying refrigeration based intercooling to the engine of a modern passenger car or haulage vehicle. Initial theoretical analysis showed that, depending on the engine specifications and the boost pressure level of the turbo/supercharger, the power improvement could range from 15–30% and there would be a similar improvement in torque. This meant a smaller engine could be used to do the work of a larger engine. The power required to run the refrigeration system, the space required and the charge air pressure drop due to its …

Simulation Of A Tubular Solid Oxide Fuel Cell Stack Operating On Biomass Syngas Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

A tubular solid oxide fuel cell (SOFC) stack was modelled and its operation on biomass syn-gas was investigated. The objective of this work was to develop a computer simulation model of a biomass gasification-SOFC (BG-SOFC) system capable of predicting performance under various operating conditions and using diverse fuels. The stack was modelled using Aspen Plus and considers ohmic, activation and concentration losses. It was validated against published data for operation on natural gas. Operating parameters such as fuel and air utilisation factor U_f and U_a, current density j and steam to carbon ratio STCR were varied and …

Validation Of A Simulation Model For A Combined Otto And Stirling Cycle Power Plant, Jim Mcgovern, Barry Cullen, Michel Feidt, Stoian Petrescu

Conference Papers

A project has been underway at the Technological University Dublin (DIT) to investigate the feasibility of a combined Otto and Stirling cycle power plant in which a Stirling cycle engine would serve as a bottoming cycle for a stationary Otto cycle engine. This type of combined cycle plant is considered to have good potential for industrial use. This paper describes work by DIT and collaborators to validate a computer simulation model of the combined cycle plant. In investigating the feasibility of the type of combined cycle that is proposed there are a range of practical realities to be faced and …

Gate 3 Grid Connection Group Processing Approach:An Analysis, John Leahy

Msc. in Energy Management

The aim of this project is to analyse the Group Processing Approach (the “GPA”) to renewable generator grid connections, and in particular the Gate 3 process which is the latest round of the GPA that is currently being implemented in the Republic of Ireland, to determine if it is the most effective approach for connecting new renewable generation. Gate 3 is the third series of the GPA for connecting renewable generation to the Irish Electricity grid where applications are processed in groups or batches. The size of the Gate 3 has bee capped at 3,900MW with applicants being selected based …

Marine Current Energy Devices: Current Status And Possible Future Applications In Ireland, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

There is a growing demand for the use of renewable energy technologies to generate electricity due to concerns over climate change. The oceans provide a huge potential resource of energy. Energy extraction using marine current energy devices (MCEDs) offers a sustainable alternative to conventional sources and a predictable alternative to other renewable energy technologies. A MCED utilises the kinetic energy of the tides as opposed to the potential energy which is utilised by a tidal barrage. Over the past decade MCEDs have become an increasingly popular method of energy extraction. However, marine current energy technology is still not economically viable …

Tidal Energy Update 2009, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

Tidal energy has the potential to play a valuable part in a sustainable energy future. It is an extremely predictable energy source, depending only on the gravitational pull of the moon and the sun and the centrifugal forces created by the rotation of the earth-moon system. Tidal energy has been exploited on a significant scale since the construction of the La Rance tidal barrage in France in 1967. A tidal barrage utilises the potential energy of the tide and has proven to be very successful, despite opposition from environmental groups. Kinetic energy can also be harnessed from tidal currents to …

Preliminary Modelling Results For An Otto Cycle/Stirling Cycle Hybrid-Engine-Based Power Generation System, Barry Cullen, Jim Mcgovern, Michel Feidt, Stoian Petrescu

Conference Papers

This paper presents preliminary data and results for a system mathematical model for a proposed Otto Cycle / Stirling Cycle hybrid-engine-based power generation system. The system is a combined cycle system with the Stirling cycle machine operating as a bottoming cycle on the Otto cycle exhaust. The application considered is that of a stationary power generation scenario wherein the Stirling cycle engine operates as a waste heat recovery device on the exhaust stream of the Otto cycle engine. This paper is primarily concerned with the development of a model for a suitable Stirling cycle engine capable of running on the …

Development Of A Theoretical Decoupled Stirling Cycle Engine, Barry Cullen, Jim Mcgovern

Conference Papers

The Stirling cycle engine is gaining increasing attention in the current energy market as a clean, quiet and versatile prime mover for use in such situations as solar thermal generation, micro cogeneration and other micro distributed generation situations. A theoretical Stirling cycle engine model is developed. Using a theoretical decoupled engine configuration in which working space swept volume, volume variation, phase angle and dead space ratio are controlled via a black-box electronic controller, a model is developed that is to be used as a tool for analysis of the ideal Stirling cycle engine and the limits on its real world …

The Very Basics Of Sustainability - An Alternative Viewpoint, Jim Mcgovern

Other resources

This paper examines the context and meaning of the term ‘sustainability’, the factors that determine and govern climate on Earth, the population of the Earth and its trends and influencers, the requirements for sustaining life and the options that are available to humankind. Some viewpoints are presented that are alternative to ‘conventional alternative’ thinking. The author advocates keeping an open mind on all available options, including the use of oil, gas, coal, tar sands, carbon capture and sequestration, nuclear power etc., as well as the technologies that are more widely considered ‘green’ and also argues that humankind needs to face …

The Very Basics Of Sustainability - An Alternative Viewpoint (Slides With Audio) (Large File! To Speed Up Download, Right-Click On "Download" Link To Save To Own Pc.), Jim Mcgovern

Other resources

This presentation sets out the very basics of ‘sustainability’, although a definition of sustainability is not attempted. Some of the very basics are the context in which the Earth and humankind exist in space and time, the Earth’s climate, the Earth’s population and humankind’s options and choices. The author advocates keeping an open mind on all available options, including the use of oil, gas, coal, tar sands, carbon capture and sequestration, nuclear power etc., as well as the technologies that are more widely considered ‘green’. The author also argues that, in addressing the challenges that humankind faces, globally concerted effort …

Economic And Environmental Performance Analysis Of Pv Systems For Domestic Applications In Ireland, Lacour Ayompe, Aidan Duffy, Sarah Mccormack, Michael Conlon

Conference Papers

Long-term monthly average daily solar radiation values on horizontal surfaces at 20 locations in Ireland were used to model the performance of a 1.72 kWp grid-connected PV system. Global solar radiation on horizontal surfaces varied between 865.1 and 1,127.9 kWh/m2/yr with a mean of 947.9 kWh/m2/yr. Annual energy yields varied between 869 and 1,156 960 kWh/kWp with a mean of 960 kWh/kWp. The capacity factor for the PV system varied between 9.9 and 13.2% while the mean was 11.0%. System cost parameters, long-term annual average electricity domestic rate cost escalation were used to calculate the Net Present Value (NPV), cost …

Heat Transfer Correlations For Low Approach Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

The experimental performance of an open industrial scale cooling tower, utilising small approach temperature differences (1–3 K), for rejection of heat at the low water temperatures (11–20 °C) typical of chilled ceilings and other sensible air–water heat dissipation systems in buildings, is examined. The study was carried out under temperate maritime climatic conditions (3–18 °C wet-bulb temperature range). Initially a theoretical analysis of the process at typical conditions for this climate was conducted, which indicated that a water to air (L/G) mass flow rate ratio of less than 1.0 was required for effective operation. Consequently for these low L/G ratios, …

Renewable Energy Resources And Technologies Applicable To Ireland, Fergal O'Rourke, Fergal Boyle, Anthony Reynolds

Articles

The energy consumed in Ireland is primarily achieved by the combustion of fossil fuels. Ireland’s only indigenous fossil fuel is peat; all other fossil fuels are imported. As well as fossil fuels continually becoming more expensive, their use as an energy source also has a negative impact on the environment. Ireland’s energy consumption can be separated into 3 divisions; transportation, electricity generation and heat energy. Ireland however has a vast range of high quality renewable energy resources. Ireland has set a target of 33% of its electricity will be generated from renewable sources by 2020[1]. The use of biomass, wind …

Simulation Of A Tubular Solid Oxide Fuel Cell Stack Operating On Biomass Syn-Gas Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

A tubular solid oxide fuel cell (SOFC) stack is modelled and its operation on biomass syn-gas is investigated. The objective of this work is to develop a computer simulation model of a biomass gasification-SOFC (BG-SOFC) system capable of predicting performance under various operating conditions and using diverse fuels. The stack is modelled using Aspen Plus and considers ohmic, activation and concentration losses. It is validated against published data for operation on natural gas. Operating parameters such as fuel and air utilisation factor (U_f and U_a), current density (j) and steam to carbon ratio ( …

Providing Academic Leadership Through The Role Of Senior Lecturer 1 (Teaching) Using The Theme Of 'Sustainable Energy' As An Example, Jim Mcgovern

Articles

An academic leader should lead in their particular area and should love what they are doing. An example of leadership in the area of 'sustainable energy use' is presented that involves leading through identifying and participating in the development of emerging technologies. Excellent academic leadership can be provided by a Senior Lecturer through active research, incorporating the latest developments in student-centred learning in their work and providing example and encouragement for colleagues and learners.

Modelling And Simulation Of A Biomass Gasification-Solid Oxide Fuel Cell Combined Heat And Power Plant Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Conference Papers

In this paper the operation and performance of a high temperature solid oxide fuel cell (SOFC) stack on biomass syn-gas from a demonstration biomass gasification combined heat and power (CHP) plant is investigated. The objective of this work is to develop a computer simulation model of a biomass-SOFC CHP system, flexible enough for use in industry, capable of predicting system performance under various operating conditions and using diverse fuels. The biomass gasifier is of the dual fluidised bed (DFB) type with steam as the gasifying agent and is operated at atmospheric pressure. The tubular SOFC configuration, developed by Siemens Power …

Simulation Of A Circulating Fluidised Bed Biomass Gasifier Using Aspen Plus: A Performance Analysis, Wayne Doherty, Anthony Reynolds, David Kennedy

Conference Papers

In the near future biomass gasification is likely to play an important role in energy production and conversion. Its application has great potential in the context of climate change mitigation, increasing efficiency and energy security. Atmospheric circulating fluidised bed (CFB) technology was selected for the current study. An original computer simulation model of a CFB biomass gasifier was developed using ASPEN Plus (Advanced System for Process ENgineering Plus). It is based on Gibbs free energy minimisation and the restricted equilibrium method was used to calibrate it against experimental data. This was achieved by specifying the temperature approach for the gasification …