Energy Systems Commons^™

Modeling Mass And Thermal Transport In Thin Porous Media Of Pem Fuel Cells, Vinaykumar Konduru

Dissertations, Master's Theses and Master's Reports

Water transport in the Porous Transport Layer (PTL) plays an important role in the efficient operation of polymer electrolyte membrane fuel cells (PEMFC). Excessive water content as well as dry operating conditions are unfavorable for efficient and reliable operation of the fuel cell. The effect of thermal conductivity and porosity on water management are investigated by simulating two-phase ow in the PTL of the fuel cell using a network model. In the model, the PTL consists of a pore-phase and a solid-phase. Different models of the PTLs are generated using independent Weibull distributions for the pore-phase and the solid-phase. The …

The Impact Of Water Injection On Spark Ignition Engine Performance Under High Load Operation, Jeremy Worm

Dissertations, Master's Theses and Master's Reports

An experimental effort has been completed in which water injection was investigated as a means of enabling increases in engine output and high load efficiency. Water was injected into the intake port of a direct fuel injected, 4-cylinder, boosted engine with dual independent variable valve timing. The water was shown to increase volumetric efficiency and decrease the onset of knock which in turn enable more optimal combustion phasing. Both of these affects resulted increases in load of up to 5.5% at the same manifold pressure as the baseline case. The advancement of combustion phasing, combined with elimination of fuel enrichment …

Heat Transfer Analysis In A Paddle Reactor For Biomass Fast Pyrolyis, Ankith Ullal

Dissertations, Master's Theses and Master's Reports

Heat transfer analysis was performed on a novel auger reactor for biomass fast pyrolysis. As part of this analysis, correlations for specific heat capacity and heat transfer coefficients for biomass (sawdust) and sand (used as heat transfer medium) were developed. For sand, the heat transfer coefficient followed a power law distribution with reactor fill level and temperature. For raw biomass, the heat transfer coefficient also showed similar dependence on fill level, but was independent of temperature up to 300°C. These correlations were used in a one dimensional heat transfer model developed to calculate the heating time and heating rate of …

Model-Based Control Of Hybrid Electric Powertrains Integrated With Low Temperature Combustion Engines, Ali Soloukmofrad

Dissertations, Master's Theses and Master's Reports

Powertrain electrification including hybridizing advanced combustion engines is a viable cost-effective solution to improve fuel economy of vehicles. This will provide opportunity for narrow-range high-efficiency combustion regimes to be able to operate and consequently improve vehicle’s fuel conversion efficiency, compared to conventional hybrid electric vehicles (HEV)s. Low temperature combustion (LTC) engines offer the highest peak brake thermal efficiency reported in literature, but these engines have narrow operating range. In addition, LTC engines have ultra-low soot and nitrogen oxides (NOx) emissions, compared to conventional compression ignition and spark ignition (SI) engines. This dissertation concentrates on integrating the LTC engines (i) in …

Impact Of Natural Gas Direct Injection On Thermal Efficinecy In A Spark Ignition Engine, James Sevik

Dissertations, Master's Theses and Master's Reports

Interest in natural gas as an internal combustion engine fuel has been renewed due to its increasing domestic availability and stable price relative to other petroleum fuel sources. Natural gas, comprised mainly of methane, allows for up to a 25% reduction in engine out CO2 emissions due to a more favorable hydrogen-to-carbon ratio, relative to traditional petroleum sources. Traditional methods of injecting natural gas can lead to poor part-load performance, as well as a power density loss at full load due to air displacement in the intake manifold. Natural gas direct injection, which allows the fuel to be injected directly …

Photovoltaic Cooking In The Developing World, Tyler Watkins, Christopher O'Day, Omar Arriaga

Mechanical Engineering

The challenge of clean cooking is faced by hundreds of millions of people worldwide. We present a cooking technology consisting of a solar panel directly connected to an electric heater in a well-insulated chamber. Assuming continued decrease in solar panel prices, we anticipate that in a few decades Solar Electric Cooking technologies will be the most common cooking technology for the poor. Appropriate use of insulation reduces the power demand making low-power Insulated Solar Electric Cooking systems already cost competitive.

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Significance Of Parameters Affecting The Performance Of A Passive Down-Draft Evaporative Cooling (Pdec) Tower With A Spray System, Daeho Kang, Richard K. Strand

Publications and Research

PDEC towers with spray systems are known to achieve substantial energy savings. Various parameters such as the wet-bulb depression, the tower height, and the wind speed have been known to be key factors affecting the performance of the system. To date, the significance of these parameters and other important factors have not been adequately treated in the literature. There also has been a lack of models that can successfully investigate potential benefits of the system under various conditions where this particular system could be applicable. To address these critical issues, this study performed a parametric analysis by using a FLUENT …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Me 350 Air Conditioning Experiment, Joshua Baida, Ellie Hallner, Tyler Eschenbach

Mechanical Engineering

In keeping with Cal Poly's focus on physically applying the concepts learned in the classroom, our team of engineering students has compiled a laboratory experiment displaying the basic thermodynamic cycle found in air conditioning systems. This vapor compression cycle is displayed on a visualization board that features all four major components of the system: the compressor, the evaporator, the condenser, and the throttling valve. Students will take measurements of temperature and pressure at each stage in the cycle and also gauge the power draw from the compressor to gain an understanding of how performance and electricity cost come into play …

Solar Thermal Collector, Hazel Tickner, Tyson Nakamura

All Undergraduate Projects

During the course of this project, a solar thermal collector and supporting stand were designed and manufactured to be used during Mechanical Engineering Technology labs. Students will be able to use the collector to heat water, with the sun being the only heat source. The collector was designed by calculating surface area limitations, estimated solar input, and desired efficiency, to find the required water flow rate. From there, the necessary pipe lengths and diameters were determined, and the solar thermal collector was constructed. Two pipe paths were manufactured: a curved path, and a manifold path. Students will be able to …

An Experimental Investigation Of Heat Transfer For Arrays Of Impingement Jets Onto The Featured Surfaces With Cylindrical And Elliptical Raised Surfaces, Marc A. Medina

Honors Undergraduate Theses

This study focuses on multi-jet impingement for gas turbine geometries in which the objective is to understand the influence of the roughness elements on a target surface to the heat transfer. Current work has proven that implementing roughness elements for multi-jet impingement target surfaces has increased heat transfer ranging anywhere from 10-30%. This study has chosen to investigate three different roughness elements, elliptical in cross-section, to compare to smooth surface geometries for multi-jet impingement. An experimental was taken for this study to extend the current knowledge of multi-jet impingement geometries and to further understand the heat transfer performance. A temperature …

Predictive Control Of Power Grid-Connected Energy Systems Based On Energy And Exergy Metrics, Meysam Razmara

Dissertations, Master's Theses and Master's Reports

Building and transportation sectors account for 41% and 27% of total energy consumption in the US, respectively. Designing smart controllers for Heating, Ventilation and Air-Conditioning (HVAC) systems and Internal Combustion Engines (ICEs) can play a key role in reducing energy consumption. Exergy or availability is based on the First and Second Laws of Thermodynamics and is a more precise metric to evaluate energy systems including HVAC and ICE systems. This dissertation centers on development of exergy models and design of model-based controllers based on exergy and energy metrics for grid-connected energy systems including HVAC and ICEs.

In this PhD dissertation, …

An Experimental Investigation Of The Effect Of Temperature And Space Velocity On The Performance Of A Cu-Zeolite Flow-Through Scr And A Scr Catalyst On A Dpf With And Without Pm Loading, Vaibhav Kadam

Dissertations, Master's Theses and Master's Reports

Abstract The heavy-duty diesel (HDD) engines use the diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and urea injection based selective catalytic reduction (SCR) systems in sequential combination, to meet the US EPA 2010 PM and NOₓ emission standards. The SCR along with a NH₃ slip control catalyst (AMOX) offer NOₓ reduction >90 % with NH₃ slipHowever, there is a strong desire to further improve the NOₓ reduction performance of such systems, to meet the California Optional Low NOₓ Standard implemented since 2015. Integrating SCR functionality into a diesel particulate filter (DPF), by coating the SCR catalyst on the DPF, …

High Temperature Hepa Filter Test Unit Upgrades, Alexander Krippner, Ian Corcorran, Michael Burlando

Mechanical Engineering

No abstract provided.

Evaluation Of Two-Phase Evaporation Pressure Drop Correlations For Low Refrigerant Mass Flux., Anna Fenko

Electronic Theses and Dissertations

This study was conducted to evaluate three currently popular two-phase pressure drop models for extremely low velocity refrigerant flow through smooth circular evaporators in household refrigeration systems. Experimental data was taken at mass fluxes under 70 kg/m²s for two refrigerants, R134A and R600A, internal diameters of aluminum evaporators ranging from 0.186 to 0.317 inches, U-bend internal radii ranging from 0.342 to 0.750 inches in horizontal and vertical orientations of evaporators. The geometry of the samples closely resembled a commonly used serpentine shape with multiple U-bends experiencing both, up- and down-flow of the refrigerant. Two empirical models, Müller-Steinhagen & …

Simulation Of An Air Cooled Single-Effect Solar Absorption Cooling System With Evacuated Tube Collectors, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Consistently increasing CO2 emission and ozone depletion from synthetic refrigerants are serious environmental issues challenging the scientific community. Absorption cooling systems give scope of utilizing low grade energy source for generating cooling effect. Solar energy is one of these low grade energy sources and with considering the fact that cooling demand increases with the intensity of solar radiation, solar refrigeration has been considered as a logical solution.

This thesis consists of two different simulation stages, in the first stage, a single effect lithium bromide absorption cooling system with constant cooling capacity is modeled and the effect of ambient and generator …

An Energy Cube Project For Teaching Engineering Design Process, Fionnuala Farrell, Shannon Chance, Micheal O'Flaherty

Conference papers

This year, the College of Engineering and the Built Environment at our institute inaugurated a new Common First Year design project module that helps inform students in the selection of a specific engineering discipline. Each student, prior to selecting their bachelor’s specialism, completes three group-based design projects: a bridge design project (to familiarise students with civil and structural engineering), a RoboSumo project (involving robotics, programming, electrical and electronics engineering), and an Energy Cube project (introducing fundamentals of mechanical, manufacturing and design, and building services engineering). This paper focuses on how the engineering design process was taught via the Energy Cube. …

Assessment Of Critical Technologies For Gas Turbine Engines Using Numerical Tools, Vinicius Pessoa Mapelli, Guillermo Paniagua, Jorge Sousa

The Summer Undergraduate Research Fellowship (SURF) Symposium

In 2014 gas turbine engine has reached a market value of 82.5 billion dollars, of which 59.5% are related to aircraft propulsion. The continuous market expansion attracts more and more the interest of researchers and industries towards the development of accurate numerical techniques to model thermodynamically the entire engine. This practice allows a performance and optimization analysis before the actual experimental testing, reducing the time and required investment in the design of a new engine. In this paper, a recently developed open source numerical tool named “Toolbox for the Modeling and Analysis of Thermodynamic Systems” (T-MATS) is used to assess …

Increasing Isentropic Efficiency With Hydrostatic Head And Venturi Ejection In A Rankine Power Cycle, Nathan Daniel Ruiz

Master's Theses

This thesis describes the modifications made to the Cal Poly Thermal Science Laboratory’s steam turbine experiment. While the use of superheating or reheating is commonly used to increase efficiency in a Rankine cycle the methods prove unfeasible in a small scale project. For this reason, a mathematical model and proof of concept design using hydrostatic head generated by elevation and venturi ejection for use by the condenser is developed along with the equations needed to predict the changes to the system. These equations were used to create software to predict efficiency as well as lay down the foundation for future …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Faculty Publications

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Transient Thermoelectric Supercooling: Isosceles Current Pulses From A Response Surface Perspective And The Performance Effects Of Pulse Cooling A Heat Generating Mass, Alfred Piggott

Dissertations, Master's Theses and Master's Reports

With increased public interest in protecting the environment, scientists and engineers aim to improve energy conversion efficiency. Thermoelectrics offer many advantages as thermal management technology. When compared to vapor compression refrigeration, above approximately 200 to 600 watts, cost in dollars per watt as well as COP are not advantageous for thermoelectrics. The goal of this work was to determine if optimized pulse supercooling operation could improve cooling capacity or efficiency of a thermoelectric device. The basis of this research is a thermal-electrical analogy based modeling study using SPICE. Two models were developed. The first model, a standalone thermocouple with no …

Heat Transfer Enhancement And Applications Of Femtosecond Laser Processed Metallic Surfaces, Corey M. Kruse

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, functionalized 304 stainless steel metallic surfaces were created with the use of a Femtosecond Laser Surface Processing (FLSP) technique. The laser processing technique produces self-organized micro/nanostructures on the surface. The heat transfer performance of various FLSP functionalized surfaces were characterized through pool boiling and Leidenfrost experiments. Enhancement in both the nucleate and film boiling heat transfer were observed through an increase of the critical heat flux and heat transfer coefficient as well as shifts in the Leidenfrost temperature respectively. For both experiments, a polished reference sample was used as a baseline line to compare against the …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Economic, Energy And Ghg Emissions Performance Evaluation Of A Whispergen Mk Iv Stirling Engine Μ-Chp Unit In A Domestic Dwelling, Gerry Conroy, Aidan Duffy, Lacour Ayompe

Articles

This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004 - July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the µ-CHP unit and a condensing gas boiler revealed that the µ-CHP unit resulted in an annual cost saving of …

Investigation Of Boiling Performance Of Graphene-Coated Surfaces, Daniel C. Stack

Renée Crown University Honors Thesis Projects - All

In this Capstone Project, I sought to investigate the boiling performance of graphene-coated surfaces. Boiling was accomplished in a pool boiling chamber, with samples of graphene-coating SiO₂ wafers. I developed a procedure for graphene transfer for sample fabrication. Samples were prepared with graphene grown on copper substrates by chemical vapor deposition (CVD). Graphene was transferred from copper substrates to SiO­₂ wafers by a thermal release transfer tape. Copper was etched away from the tape-graphene combination by ferric chloride, and the tape was peeled away after heating, leaving graphene on the SiO₂ substrate. Contact angles were measured to …

Simulation Of An Intake Manifold Pre-Heater For Cold Diesel Engine Startup, Patrick K. Kreun

Masters Theses

Ensuring consistent, reliable diesel engine startups in cold temperatures is of utmost importance in a number of applications. Under extreme temperatures, the use of glow plugs is complemented by intake manifold heaters. In these, the energy released from combustion increases the intake air temperature before the air enters the main combustion chamber. Since the process also alters the stoichiometry of the fuel-air mixture at the intake ports, the preheater operation must be optimized in order to guarantee successful and reliable in-cylinder combustion during engine startups. This paper describes the development of an intake manifold model incorporating an air pre-heater for …

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

LSU New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Study On The Integration Of A Novel Absorption Chiller Into A Microscale Combined Cooling, Heating, And Power (Micro-Cchp) System, Scott J. Richard

LSU New Orleans Theses and Dissertations

This study explores the application of micro-CCHP systems that utilize a 30 kW gas microturbine and an absorption chiller. Engineering Equation Solver (EES) is used to model a novel single-effect and double-effect water-lithium bromide absorption chiller that integrates the heat recovery unit and cooling tower of a conventional CCHP system into the chiller’s design, reducing the cost and footprint of the system. The results of the EES model are used to perform heat and material balances for the micro-CCHP systems employing the novel integrated chillers, and energy budgets for these systems are developed. While the thermal performance of existing CCHP …