Energy Systems Commons^™

Desalination For Sustainable Water Production With An Emphasis On Low Pressure Distillation, Jessica Vivian Savage

Doctoral Dissertations and Master's Theses

Freshwater resources depletion is a growing concern. This freshwater scarcity motivates research into seawater desalination as a means for alleviating the stresses on water demands. The primary methods of desalination include filtration and distillation. This paper explores the potential energy savings of vacuum distillation for seawater desalination to reduce the amount of energy needed to achieve phase change.

Depending on the vacuum boiler design, the vaporization mechanism may be boiling, evaporation, or cavitation. There is very little literature on cavitation that involves mass transfer, so cavitation is not developed here. This thesis focuses on standard models for boiling and evaporation …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Improving Vertical Axis Wind Turbine (Vawt) Performance With Placement Strategies: Final Report, Patrick A. Tebbe, Nazli A. Yilmaz Wodzinski, Namyong Lee

Mechanical and Civil Engineering Department Publications

This project was focused on the use and placement of vertical axis wind turbines (VAWTs). Studies were focused on areas not typically addressed in previous work; small wind at very low elevations (i.e. within the boundary layer). Numerical studies were made of how VAWTs function as well as the potential wind environments they may be placed in. A simplified numerical code, based on two-dimensional potential flow functions, was developed to model flow around buildings and other structures. The code allows a rapid determination of regions where flow may experience speed-up and where turbulence may result.

Experimental facilities were designed and …

Renewable Energy Production By Solar Chimney: The Influence Of Curved Guide Vanes On The Performance Of A Solar Chimney Using Cfd Simulation, Haokun Xue

Theses, Dissertations and Capstones

The aim of this study is to investigate the effect of the guide vanes on the efficiency of the turbine of solar chimney power plant using Computational Fluid Dynamics (CFD). In this study, a 3-Dimentional CFD simulation of solar chimney power plant based on the Manzanares prototype is performed. The CFD simulation is validated by comparing the experimental data from the Manzanares prototype and simulation data with both 2D and 3D cases. To capture turbulent flow inside the chimney, the SST 𝑘 − 𝜔 turbulence model is used. The first object is to investigate the flow performance under the influence …

Econometric Frameworks For Energy Prediction, Naveen Chandra Iraganaboina

Electronic Theses and Dissertations, 2020-2023

Global warming and associated role of energy consumption across various sectors is a well-researched topic in recent years. Understanding current urban energy consumption patterns will allow us to understand how future energy consumption patterns will evolve. With electrification of vehicles and potentially altering culture of work from home, the energy usage at regional level would see a significant change in the future. The current PhD dissertation contributes to energy consumption analysis of a region by analyzing residential energy consumption, commercial energy consumption and transportation energy use by households. The aggregation of these energy consumption within a region contributes to the …

A Comprehensive Comparative Investigation On Solar Heating And Cooling Technologies From A Thermo-Economic Viewpoint—A Dynamic Simulation, Hassan Jafari Mosleh, Pooria Behnam, Maryam Abbasi Kamazani, Omid Mohammadi, Soheil Kavian, Pouria Ahmadi, Marc A. Rosen

Research outputs 2014 to 2021

© 2020 The Authors. Energy Science & Engineering published by the Society of Chemical Industry and John Wiley & Sons Ltd. The yearly thermo-economic performance is dynamically investigated for three solar heating and cooling systems: solar heating and absorption cooling (SHAC), solar heating and ejector cooling (SHEC), and heating and solar vapor compression cooling (HSVC). First, the effects of important design parameters on the thermo-economic performance of the systems to supply the heating and cooling loads of the building are evaluated. The systems are parametrically analyzed with the weather conditions of Tehran, Iran. The results show that the life cycle …

Feasibility Study On Concentrated Solar Power Plants In Malaysia, De Jen Choy

Student Works (2020-2029)

The rapidly growing economy and population in Southeast Asia has elevated the need for affordable, secured, sustainable and environmentally friendly energy sources. One such energy source is solar energy which is a suitable energy source for most Southeast Asian countries which are within the Sun Belt region. This study performs a performance and financial analysis on concentrated solar power (CSP) technologies, specifically the solar power tower (SPT) in the Malaysian environment through the use of simulation software. The significance of the study lies in the fact that limited research has been done on CSP technologies in Malaysia and the study …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Residential Thermal Storage And Cooling, Joao Marcelo Rocha Belmonte, Jacob Anderson, Andrew Clarke, Daphne Forester, Bianca Hardtke, Josh Hartman, Marc D. Compere

Sustainability Conference

No abstract provided.

Solar Powered Parking Lot Lights, Jordyn Taylor

Sustainability Conference

Solar energy is a renewable resource growing exponentially around the country over the past few decades. Solar energy works through the use of photo-voltaic cells, which work to convert energy from sunlight into electricity. This is done within solar panels, which are then connected to batteries for energy storage to use as needed. As production has increased over past decades, the cost for solar panel hardware and installment has thus fallen to meet consumer need. While most common implementations include solar panels attached to one’s home or solar panel ‘fields’ for charging entire towns, there has been a steady rise …

Electrification Of Domestic Hot Water To Aid The Integration Of Renewable Energy In The California Grid, Alejandro Cervantes

Cal Poly Humboldt theses and projects

Water heating in residential buildings, also known as domestic hot water (DHW), is the third largest use of energy after appliances and space conditioning. About 90% of the residential buildings in the state use natural gas fueled water heaters, 6% use electricity, and a small percent use liquefied petroleum gas (LPG) or solar water heaters. The current energy use associated with residential water heating is small relative to the total amount of energy consumption in the residential building sector, but it is still a contributor of greenhouse gas (GHG) emissions. Improving hot water systems can be beneficial for bill customer …

Adapting To Extreme Heat: Social, Atmospheric, And Infrastructure Impacts Of Air Conditioning In Megacities - The Case Of New York City, Harold Gamarro

Dissertations and Theses

Extreme heat events are becoming more frequent and intense in most large cities. Built-up surfaces also limit cooling mechanisms, leading to warmer conditions in cities, a phenomenon called the Urban Heat Island (UHI). This presents major challenges to reduce adverse health effects of hot weather, particularly in vulnerable populations like the elderly and low-income communities. Here we explore the overall impacts of increasing air conditioning (AC) system adoption in residences as an adaptive measure to reduce human health risks under heat waves, with New York City (NYC) as a case study. This study uses AC adoption data from the 2017 …

Carbon-Based Interlayers In Perovskite Solar Cells, Aleksandr P. Litvin, Xiaoyu Zhang, Kevin Berwick, Anatoly V. Fedorov, Weitao Zheng, Alexander V. Baranov

Articles

Perovskites are solution-processed, high-performance semiconductors of interest in low-cost photovoltaics. The interfaces between the perovskite photoactive layers and the top and bottom contacts are crucial for efficient charge transport and minimizing trapping. Control of the collection of charge carriers at these interfaces is decisive to device performance. Here, we review recent progress in the realization of efficient perovskite solar cells using cheap, easily processed, stable, carbon-based interlayers. Interface materials including graphene, carbon nanotubes, fullerenes, graphene quantum dots and carbon dots are introduced and their influence on device performance is discussed.

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Hvac System Energy Audit For Leverett Elementary School, Connor Smalling

Biological and Agricultural Engineering Undergraduate Honors Theses

Leverett Elementary School is located in Fayetteville, AR. The school needs significant upgrades to its infrastructure. The Fayetteville Public School District has voted to pursue an Energy Services Performance Contract (ESPC) in order to finance the desired upgrades to Leverett Elementary, among other schools in the district.

The scope of this thesis was to perform an energy audit on the existing heating, ventilation, and air conditioning (HVAC) system. By using an energy modeling software, eQuest, the building and the existing base system were modeled to determine utility consumption. Three different HVAC system alternatives were analyzed against the base system by …

Potential Use Of High Rate Algae Ponds For Resource Recovery In The Water-Food-Energy Nexus For Tanzania: A Review, Mary Kayombo

Tanzania Journal of Engineering and Technology (TJET)

The use of High Rate Algal Ponds (HRAPs) for the treatment of wastewater and resource recovery has raised interest in recent years. Treatment of wastewater through this technology has proved to have high efficiency in reducing the level of pollution, nutrients, dissolved solids as well as pathogens. HRAPs are more efficient than conventional Wastewater Stabilization Ponds (WSPs) due to their design approach that provides room for high rate bio-chemical processes, which increase the mechanisms of nutrients and pathogens removal as well as the rate of micro-algae production for purposes of resource recovery. This paper reviews the upgrading potential of existing …

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Proposed Delivery And Return Water Temperatures For Dartmouth College Hot Water Network, Storm Mata

ENGS 86 Independent Projects (AB Students)

This study aimed to verify the viability of the planned hot water heating network at Dartmouth, and determine the necessary hot water radiator areas needed to satisfy the empirically-determined heat demand for buildings on campus, using 5 year of steam con- sumption data. In order to verify viability, the pressure and temperature of the delivery steam and return condensate of the current heating network were used to find the amount of heat delivered per pound of steam to campus. The above-mentioned steam consump- tion data were then used to find the max heat demand for the past five years and …

A Novel Approach Towards Investigating The Performance Of Different Pvt Configurations Integrated On Test Cells: An Experimental Study, Vivek Tomar, Brian Norton, G. N. Tiwari

Articles

This study elaborates the theoretical and experimental analysis for the effectiveness of different photovoltaic thermal (PVT) configurations along with their building implications. An experiment was performed on especially designed four identical prototype test cells emphasise the building integration photovoltaic thermal (BiPVT) systems. A comparative analysis of four different possible PVT configurations integrated on identical test cells namely; Case 1: Glass-to-glass PV with duct integrated on a test cell, Case 2: Glass-to -glass PV without duct integrated on a test cell, Case 3: Glass to tedlar PV with duct integrated on a test cell and Case 4: Glass to tedlar PV …

Calculation Methods Of Radon-222 Radiological Activity For Norm Plant With Ventilation, Pedro M. Dieguez-Elizondo, Paul G. O'Donohoe, Tomas Gil-Lopez, Juan Castejon-Navas, Miguel A. Gálvez-Huerta

Articles

A procedure is proposed to determine the radiological activity of air present in the working area of a NORM (Naturally-Occurring Radioactive Materials) plant. This NORM plant is located in the United Arab Emirates and is dedicated to the recycling of material and equipment used in oil extraction facilities. Substantial quantities of NORM waste will be present inside the enclosed plant facilities and will exhale significant amounts of Radon-222 into the working environment. The continued inhalation of this gas and its progeny has been shown to cause lung cancer. In order to reduce the concentration level of the aforementioned gas to …

Economic Appraisal Of Hybrid Solar-Biomass Thermophotovoltaic Power Generation, C. M. Iftekhar Hussain Cmih, Aidan Duffy, Brian Norton

Conference Papers

The techno-economic parameters that influence the commercial deployment of hybrid thermophotovoltaic (TPV) solar power generation are determined using annual system simulations. It has been found that a TPV cell price of E5/cm2 or less together with a TPV operating temperature under 800°C is required for a hybrid solar–biomass TPV power plant to be economically competitive with the state-of-the-art hybrid solar–biomass Rankine cycle power plants.

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Towards Environmentally Sustainable And Cost-Effective Food Distribution In The U.S., Jasmina Burek

Graduate Theses and Dissertations

Distribution centers (DCs) and supermarkets have an important role in food sustainability, but no previous research has accounted for their environmental impact. The purpose of this research was to assess environmental sustainability of grocery, perishables, and general merchandise DCs; to estimate food storing and retailing impact; and to provide cost-effective strategies to reduce DCs’ environmental impacts. The importance and relevance of the research is threefold: improving sustainability of DCs, food storing, and food retailing. The main method used in this research was the life cycle assessment (LCA) method. An initial study calculated environmental impacts of the Wal-Mart Stores, Inc. DCs, …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Factors Influencing Household Solar Adoption In Santiago, Chile, Jeffrey P. Walters, Jessica Kaminsky, Claudio Huepe

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

In Santiago, Chile, the market conditions are seemingly excellent for the household adoption of photovoltaic (PV) technology, yet the uptake is negligible. To explore this paradox, the authors conducted a Delphi study to solicit the knowledge of a panel of Chilean PV experts. These efforts yielded 26 factors—both motivations and barriers—impacting the diffusion of PV in Santiago. Of the 26, experts were in consensus on the relative importance of 21. The literature suggests that diffusion of PV technologies is influenced by complex technical, economic, and social factors. Similarly, the experts saw influence from financial, environmental, and energy supply (e.g., electrical …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

An Integrated Closed Convergent System For Optimal Extraction Of Head-Driven Tidal Energy, Michelle Ann Vieira

UNF Graduate Theses and Dissertations

As the demands for energy increased with the global increase in population, there is a need to create and invest in more clean and renewable energy sources. Energy derived from the movement of the tides is an ancient concept that is currently being harnessed in a handful of large tidal range locations. However, the need to move from fossil fuel driven energy sources to those that are clean and non-polluting is a priority for a sustainable future. Globally, hydropower potential is estimated to be more than 16,400-Terawatt hours annually. Given that the electricity consumption worldwide was at 15,068-Terawatt hours in …

Pollution Prevention In The Great Lakes Basin: Working With Pulp & Paper Manufacturers, Eugene Park

Journal of Environmental Sustainability

In response to growing concerns over persistent toxic substances in the Great Lakes, new initiatives are in place to address and mitigate pollutant loadings to these large natural waterbodies. With support from the U.S. Environmental Protection Agency and New York Department of Environmental Conservation, the New York State Pollution Prevention Institute (NYSP2I) worked with pulp & paper companies in the Great Lakes Basin in an effort to find solutions to reduce environmental impacts from this industry sector. Based on currently available EPA toolkits, NYSP2I developed and utilized an assessment tool called Lean, Energy, and Environment (LE2). Five different paper manufacturers …