Energy Systems Commons^™

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Design Of A Portable Biogas Purification And Storage System, Anikumar Kosna, Bade Shrestha

Faculty Research and Creative Activities Award (FRACAA)

The objective of this study is to propose and design a commercial portable purification and storage system to commercialize biogas (which mainly consists of 45 - 75 % of methane and 15 - 16% of carbon dioxide), produced from household/non-commercial biogas plants. The selection of purification process is based on the portability of the purification system.

Fluorescence Of Cdse/Zns Quantum Dots In Toluene: Effect Of Cyclic Temperature, Ting Chen, Weiling Luan, Shaofu Zhang, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Quantum dots (QDs) are the potential material for the application in optical thermometry, and have been successfully applied to solar cells, LEDs, bio-labeling, structural health monitoring, etc. In this paper, we study the fluorescence properties of CdSe/ZnS QDs in toluene under the action of heating-cooling cycles. The experimental results show that, in a heating-cooling cycle, increasing temperature causes red-shift of the emission peak and the decrease of the PL intensity, and decreasing temperature causes blue-shift of the emission peak and the increase of the PL intensity. The surface structures of the QDs likely are dependent on the cycle numbers, which …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Performance Of C2H4 Reductant In Activated-Carbon-Supported Mnox-Based Scr Catalyst At Low Temperatures, Guangli Liu, Dongtai Han, Jie Cheng, Yongshi Feng, Wenbin Quan, Li Yang, Kozo Saito

Mechanical Engineering Faculty Publications

Hydrocarbons as reductants show promising results for replacing NH₃ in SCR technology. Therefore, considerable interest exists for developing low-temperature (< 200 °C) and environmentally friendly HC-SCR catalysts. Hence, C₂H₄ was examined as a reductant using activated-carbon-supported MnOx-based catalyst in low-temperature SCR operation. Its sensitivity to Mn concentration and operating temperature was parametrically studied, the results of which showed that the catalyst activity followed the order of 130 °C > 150 °C > 180 °C with an optimized Mn concentration near 3.0 wt.%. However, rapid deactivation of catalytic activity also occurred when using C₂H₄ as the reductant. The mechanism of deactivation was explored and is …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Electrochemical Hydrogenation Of Acetone To Produce Isopropanol Using A Polymer Electrolyte Membrane Reactor, Chen Li, Ashanti M. Sallee, Xiaoyu Zhang, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Electrochemical hydrogenation (ECH) of acetone is a relatively new method to produce isopropanol. It provides an alternative way of upgrading bio-fuels with less energy consumption and chemical waste as compared to conventional methods. In this paper, Polymer Electrolyte Membrane Fuel Cell (PEMFC) hardware was used as an electrochemical reactor to hydrogenate acetone to produce isopropanol and diisopropyl ether as a byproduct. High current efficiency (59.7%) and selectivity (>90%) were achieved, while ECH was carried out in mild conditions (65 degrees C and atmospheric pressure). Various operating parameters were evaluated to determine their effects on the yield of acetone and …

What Can I Do As A Student To Make A Positive Impact On The Environment?, Tammy Guthrie, Greg Herzig, Kathy Prophet, Cassie Kautzer

Middle School Lesson Plans

Students discover ways they can make a positive impact on the environment.

Effects Of Methyl-Blue Addition In Sewage Substrate On The Performance Of Microbial Fuel Cell, Joseph H. Kihedu Dr.

Tanzania Journal of Engineering and Technology (TJET)

Experimental study was undertaken to evaluate performance of microbial fuel cell. Without addition of methyl blue, the cell generated 1.265 V, 0.403 mA and 56.12 mW/m2 after three hours of operation. With 300 µM methyl blue in sewage anolyte, 6.7% increase in voltage, 20.5% increase in current and 28.6% increase in power density was observed. By using ash water catholyte, addition of methyl blue in anolyte led to increase of 9.0% in voltage, 38.5% in current and 50.9% for power density. Between three and twenty four hours of continuous operation of the cell with phosphate buffer catholyte, the average voltage …

Increased Energy Yield Through Fast Pyrolysis: Empowering Malawian Villages, Diehl Mutamba

Undergraduate Honors Theses

Biomass contributes to several renewable energy technologies. This project will explore the use of fast pyrolysis to produce fuels by designing an apparatus for fast pyrolysis. Malawian people harvest firewood from the forests, which is a major contributor to deforestation. Furthermore, they convert some of it to charcoal with about 10-15% efficiency to sell to city dwellers. The project will enable herbaceous fuels to replace wood, increase charcoal yields and create new products. Firewood and charcoal produce smoke and carbon monoxide (CO) that compromises the villagers’ health.

This project will address deforestation problems, improve sustainability, decrease health hazards and improve …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Investigation On The Potential Of A Co2 Capture System, Downstream Of The Aftertreatment System For A Heavy-Duty Engine Application, Murchana Pathak

Dissertations, Master's Theses and Master's Reports

The transportation sector accounts for the second largest source of CO₂ emissions after power generation. New Corporate Average Fuel Economy (CAFE) regulations are focusing on improving energy through reduced fuel consumption and greenhouse gas emissions. This work investigates the potential of a CO₂ capture system downstream of an aftertreatment system for a heavy-duty engine application. Amine absorption has been described as one of the most effective ways to capture CO₂ from the exhaust for point sources. Therefore, using thermal-swing absorption process with potassium carbonate (K₂CO₃) as the absorbent liquid, a process was analyzed …

Investigation Of Combustion Characteristics Of A Heavy-Duty Diesel Engine Retrofitted To Natural Gas Spark Ignition Operation, Jinlong Liu

Graduate Theses, Dissertations, and Problem Reports (ETD)

The conversion of existing diesel engines to natural-gas spark ignition operation by adding a gas injector in the intake manifold for fuel delivery and replacing the diesel fuel injector with a spark plug to initiate and control the combustion process can reduce U.S. dependence on petroleum imports and curtail engine-out emissions. As the conventional diesel combustion chamber (i.e., flat head and bowl-in-piston) creates high turbulence, the engine can operate leaner, which would increase its efficiency and reduce emissions. However, natural gas combustion in such retrofitted engines presents differences compared to that in conventional spark ignited engines. Subsequently, the main goal …

Pollution Prevention In The Great Lakes Basin: Working With Pulp & Paper Manufacturers, Eugene Park

Journal of Environmental Sustainability

In response to growing concerns over persistent toxic substances in the Great Lakes, new initiatives are in place to address and mitigate pollutant loadings to these large natural waterbodies. With support from the U.S. Environmental Protection Agency and New York Department of Environmental Conservation, the New York State Pollution Prevention Institute (NYSP2I) worked with pulp & paper companies in the Great Lakes Basin in an effort to find solutions to reduce environmental impacts from this industry sector. Based on currently available EPA toolkits, NYSP2I developed and utilized an assessment tool called Lean, Energy, and Environment (LE2). Five different paper manufacturers …

Energy From Chemical Reactions: Understanding The Combustion Engine, Tammy Guthrie, Kathy Prophet, Greg Herzig, Cassie Kautzer

Middle School Lesson Plans

Automobiles produce a large amount of heat generated by the burning of gasoline. Burning gasoline is a chemical reaction that causes a phase change. This is called combustible energy. During combustion fuel combines with oxygen to release energy (such as heat, light, sound) along with another product that is often considered waste. Most of the energy produced is not used to power the automobile, but is released as heat. 19.3 pounds of the greenhouse gas, carbon dioxide, is produced from the combustion of 1 gallon of U.S. gasoline according to the U.S. Energy Information Administration.

Method For Carbon Dioxide Splitting, James E. Miller, Richard B. Diver, Nathan P. Siegel

Other Faculty Research and Publications

A method for splitting carbon dioxide via a two-step metal oxide thermochemical cycle by heating a metal oxide compound selected from an iron oxide material of the general formula A_xFe_3-xO₄, where 0≦x≦1 and A is a metal selected from Mg, Cu, Zn, Ni, Co, and Mn, or a ceria oxide compound of the general formula M_aCe_bO_c, where 0

Heat Transfer Analysis In A Paddle Reactor For Biomass Fast Pyrolyis, Ankith Ullal

Dissertations, Master's Theses and Master's Reports

Heat transfer analysis was performed on a novel auger reactor for biomass fast pyrolysis. As part of this analysis, correlations for specific heat capacity and heat transfer coefficients for biomass (sawdust) and sand (used as heat transfer medium) were developed. For sand, the heat transfer coefficient followed a power law distribution with reactor fill level and temperature. For raw biomass, the heat transfer coefficient also showed similar dependence on fill level, but was independent of temperature up to 300°C. These correlations were used in a one dimensional heat transfer model developed to calculate the heating time and heating rate of …

Hybrid Metal Oxide Cycle Water Splitting, Richard B. Diver Jr., Robert D. Palumbo, Nathan P. Siegel, James E. Miller

Other Faculty Research and Publications

Hybrid thermochemical water splitting systems are disclosed that thermally reduces metal oxides particles to displace some but not all of the electrical requirements in a water splitting electrolytic cell. In these hybrid systems, the thermal reduction temperature is significantly reduced compared to two-step metal-oxide thermochemical cycles in which only thermal energy is required to produce hydrogen from water. Also, unlike conventional higher temperature systems where the reduction step must be carried out under reduced oxygen pressure, the reduction step in the proposed hybrid systems can be carried out in air, allowing for thermal input by a solar power tower with …

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Hybrid Metal Oxide Cycle Water Splitting, Richard B. Diver Jr, Robert D. Palumbo, Nathan P. Siegel, James E. Miller

Other Faculty Research and Publications

Hybrid thermochemical water splitting cycles are provided in which thermally reduced metal oxides particles are used to displace some but not all of the electrical requirements in a water splitting electrolytic cell. In these hybrid cycles, the thermal reduction temperature is significantly reduced compared to two-step metal-oxide thermochemical cycles in which only thermal energy is required to produce hydrogen from water. Also, unlike the conventional higher temperature cycles where the reduction step must be carried out under reduced oxygen pressure, the reduction step in the proposed hybrid cycles can be carried out in air, allowing for thermal input by a …

Design And Commissioning Of A Community Scale Solar Powered Membrane-Based Water Purification System In Haiti, Shavin Pinto, Yung Wong, Kyle Fennesy, Yan Tang, Marc Compere

Publications

This paper presents the design and commissioning of a solar powered water purification system at the Ryan Epps Home for Children (REHC) in Michaud, Haiti. This system supplies clean drinking water to the 200 children who live and go to school at REHC and also to the community in the form of a micro-business. This micro-business is the mechanism for income generation for sustainable system operation. The purifier uses a three stage filtration system with a disc-type sediment filter, a 0.1 micron ultrafiltration membrane, and an ultraviolet light for disinfection. The backwash cycle extends the life of the ultrafiltration membrane …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

Modeling Of Biomass Torrefaction And Pyrolysis And Its Applications, Jordan L. Klinger

Dissertations, Master's Theses and Master's Reports - Open

Utilizing biomass provides a possible near-term alternative solution for fossil energy dependence in both electricity generation and transportation. Though thermochemical conversion can produce solid/liquid fuels that are compatible in existing infrastructure, detailed scientific chemical and mechanistic understanding are still being developed. In contribution to these efforts, this work is focused on development of a semiempirical, lumped parameter, chemical kinetic model to describe the degradation of woody biomass.

The initial kinetic model was developed in the torrefaction region to describe the gas-phase evolution of products (water, organic acids, permanent gases, and furfural) through a three consecutive reaction model. In this model, …

Process Simulation Of Biomass Gasification Integrated With A Solid Oxide Fuel Cell Stack, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

Biomass gasification-solid oxide fuel cell (BG-SOFC) combined heat and power (CHP) systems are of major interest in the context of climate change mitigation, energy security and increasing energy efficiency. Aspen Plus is employed to simulate various BG-SOFC CHP systems. The aim of the research work is to investigate the technical feasibility of these systems and to study the influence of important operating parameters and examine integration options. Systems based on dual fluidised bed steam gasification and tubular SOFC technologies are modelled. The cathode recycle and electric heater integration options are not attractive in comparison to the base case anode recycle …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Modelling Of Biomass Gasification Integrated With A Solid Oxide Fuel Cell System, Wayne Doherty

Doctoral

Biomass is of major interest as a renewable energy source in the context of climate change and energy security. Traditional biomass conversion technologies achieve low electrical efficiencies. Biomass gasification (BG) coupled with fuel cells offer higher efficiencies. Gasification is a process in which a carbonaceous fuel is converted to a combustible gas. It occurs when a controlled amount of oxidant is reacted at high temperatures with available carbon in a fuel within a gasifier. Two technologies (circulating fluidised bed air gasification and dual fluidised bed steam gasification) were modelled. Solid oxide fuel cells (SOFCs) are well suited to integration with …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Experimental Study Of Co2 Recycling Using Metal-Oxide Enhanced Coconut Char Gasification: Catalytic Effect Of Potassium Carbonate On Gasification, Mengqi Gao, Indraneel Sircar, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Biomass gasification is an important process in the production of bio-derived fuels and renewable energy. Biomass gasification with CO₂ is an endothermic process requiring high temperatures, resulting in low process-efficiency. Metals found in the ash in biomass feedstock have shown rate-promoting effects on the C-CO₂ reaction and have motivated the study of low-temperature catalytic gasification. The present study investigates the catalytic effects of potassium (K) on the biomass gasification reactivity of a coconut-derived char (>99.9% carbon) within the temperature range of 600 – 1000 ^oC. A wet-impregnation technique is used to prepare K-treated chars. Gasification of …