Electro-Mechanical Systems Commons^™

Development And Thermodynamic Analysis Of An Integrated Mild/Partial Gasification Combined Cycle (Impgc) Under Green And Brown Field Conditions With And Without Carbon Capture, Henry A. Long Iii

LSU New Orleans Theses and Dissertations

Coal is a very prominent energy source in the world, but it is environmentally unattractive due to its high sulfur and ash content as well as its alleged contribution towards climate change, but it is affordable, abundant, and has high energy content. Thus, utilizing coal in a cleaner and more efficient way has become necessary. One promising clean coal technology involves fully gasifying coal into synthesis gas, cleaning it, and feeding it into a high-efficiency combined cycle, such as an Integrated Gasification Combined Cycle (IGCC). Inspired by the recent success of warn gas cleanup (WGCU), mild and partial gasification are …

Interfacial Tailoring Of Lithium-Ion Batteries By Atomic/Molecular Layer Deposition, Qian Sun

Graduate Theses and Dissertations

Lithium-ion batteries (LIBs) are promising energy storage devices, which play significant roles in addressing problems related to fossil fuels depletion and environmental pollution. Since the 1990s, LIBs have attracted great attention for many applications. Nowadays, LIBs are dominating portable electronics, having several advantages over their forerunners, such as high voltage (3.3~4.2 V) [1,2], low self-discharge (< 5~10 %/month) [3,4], wide operation temperature (-20~60 °C) [5,6], and fast charge/discharge rate [7,8]. However, LIBs deliver an energy density of 100-220 Wh/kg in practice to date, which is far from their theoretical ones, thus hindering their further applications in electric vehicles. Additionally, LIBs have been plagued by other problems, such as intolerance to overcharge/overdischarge, low heat resistance, lithium dendrites growth, large volume change of the silicon anode, large polarization and even safety problems.

Atomic layer deposition (ALD) and molecular layer deposition (MLD) are two important techniques, both proceeding in self-limiting gas-solid reactions and exhibiting excellent capabilities for ultra-thin films, conformal coatings, and controllable growth. They can be employed to address the problems of LIBs mentioned above by …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Furnace System Improvements, Kenji K. Anzai, Ethan Fedor, Patrick Zailaa

Mechanical Engineering

This Final Design Review (FDR) documents the work done by the group to manufacture the system to deliver improvements to the furnace in the Cal Poly microfabrication laboratory (better known as the cleanroom). The document describes the material covered in the Scope of Work (SOW), including background research, customer needfinding, and the problem statement, material associated with concept development and selection for Preliminary Design Review (PDR), material detailing the design and manufacturing plan of the system for Critical Design Review (CDR), and new material detailing the manufacture of the system for FDR.

Research done for the SOW resulted in a …

Water Fun At Exploration Station Final Design Report, Brandon Dean Puccini, Sarah Rose Means, Natasha Tamlin O'Connell-Mackay

Mechanical Engineering

No abstract provided.

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

Wheelie King Trainer And Controller, Michael C. Uytingco, Paul E. Hubner, Dmitriy Petrovykh

Mechanical Engineering

The ``wheelie'' is a popular, classic bicycle trick which novice bicyclists often attempt as an introduction to advanced bike tricks. However, many are hesitant to try due to the risks and safety hazards associated with performing one. The purpose of this project is to create an on-board system which will assist a user in maintaining a wheelie after achieving the required position while incorporating safety mechanisms to prevent the user from injuring themselves or others. Additional requirements of the system are non-obstructive features and seamless transitioning between wheelie conditions.

Upon researching the state of wheelie technology, existing products, such as …

Comparative Study Of Power Semiconductor Devices In A Multilevel Cascaded H-Bridge Inverter, Kenneth Mordi

Graduate Theses and Dissertations

This thesis compares the performance of a nine-level transformerless cascaded H-bridge (CHB) inverter with integrated battery energy storage system (BESS) using SiC power MOSFETs and Si IGBTs. Two crucial performance drivers for inverter applications are power loss and efficiency. Both of these are investigated in this thesis. Power devices with similar voltage and current ratings are used in the same inverter topology, and the performance of each device is analyzed with respect to switching frequency and operating temperature. The loss measurements and characteristics within the inverter are discussed. The Saber® simulation software was used for the comparisons. The power MOSFET …

Creating A Computational Tool To Simulate Vibration Control For Piezoelectric Devices, Ahmet Ozkan Ozer, Emma J. Moore

Posters-at-the-Capitol

Piezoelectric materials have the unique ability to convert electrical energy to mechanical vibrations and vice versa. This project takes a stab to develop a reliable computational tool to simulate the vibration control of a novel “partial differential equation” model for a piezoelectric device, which is designed by integrating electric conducting piezoelectric layers constraining a viscoelastic layer to provide an active and lightweight intelligent structure. Controlling unwanted vibrations on piezoelectric devices (or harvesting energy from ambient vibrations) through piezoelectric layers has been the major focus in cutting-edge engineering applications such as ultrasonic welders and inchworms. The corresponding mathematical models for piezoelectric …

Hyperspectral Imaging For Characterizing Single Plasmonic Nanostructure And Single-Cell Analysis, Nishir Sanatkumar Mehta

LSU Master's Theses

Orientation of plasmonic nanostructures is an important feature in many nanoscale applications such as photovoltaics, catalyst, biosensors DNA interactions, protein detections, hotspot of surface-enhanced Raman spectroscopy (SERS), and fluorescence resonant energy transfer (FRET) experiments. Silver nanocubes with significant spectral signatures between 400-700 nm are observed in this experimental research. Whereas study of single cells will enable the analysis of cell-to-cell variations within a heterogeneous population. These variations are important for further analysis and understanding of disease propagation, drug development, stem cell differentiation, embryos development, and how cells respond to each other and their environment. Adipose-derived mesenchymal stem cells possess the …

Micro-Manipulation Using Learned Model, Matthew A. Lyng, Benjamin V. Johnson, David J. Cappelleri

The Summer Undergraduate Research Fellowship (SURF) Symposium

Microscale devices can be found in applications ranging from sensors to structural components. The dominance of surface forces at the microscale hinders the assembly processes through nonlinear interactions that are difficult to model for automation, limiting designs of microsystems to primarily monolithic structures. Methods for modeling surface forces must be presented for viable manufacturing of devices consisting of multiple microparts. This paper proposes the implementation of supervised machine learning models to aid in automated micromanipulation tasks for advanced manufacturing applications. The developed models use sets of training data to implicitly model surface interactions and predict end-effector placement and paths that …

Developing An Electromechanical Carbon Dioxide Sensor For Occupancy Monitoring, Joshua L. Jenkins, Allison K. Murray, Jeffrey F. Rhoads

The Summer Undergraduate Research Fellowship (SURF) Symposium

The Energy Information Administration reported in 2012 that heating and cooling processes consume nearly 35% of the total energy used by commercial buildings. In an effort to limit the amount of energy wasted in conditioning empty buildings and rooms, various occupancy detection techniques have been developed that can be paired with a smart heating, ventilation, and air conditioning (HVAC) control system. This work focused on the development of a novel carbon dioxide detector that is sensitive enough to accurately determine if, and when, a room is occupied. To test the new sensor design, a customized chamber with gas inlets was …

High-Throughput Nanoliter Dispensing Device For Biological Applications, Cole Reynolds, Euiwon Bae Dr., J Paul Robinson Dr.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Pathogen identification is a field that can contribute largely to the prevention of the spreading of illness and disease. In the past, pathogen identification has been a long and arduous process due to the time-consuming processes and steps that requires technician’s time and effort. With new technologies emerging however, screening of bacteria colonies can be done in a quick and high-throughput way. The problem is that using the current methods, bacteria cannot be transferred to petri dishes fast enough to keep up with the new screening methods. The current study focuses on exploring different methods to create an ergonomic device …

High Dynamic Range Optical Devices And Applications., Elijah Robert Jensen

Electronic Theses and Dissertations

Much of what we know about fundamental physical law and the universe derives from observations and measurements using optical methods. The passive use of the electromagnetic spectrum can be the best way of studying physical phenomenon in general with minimal disturbance of the system in the process. While for many applications ambient visible light is sufficient, light outside of the visible range may convey more information. The signals of interest are also often a small fraction of the background, and their changes occur on time scales so quickly that they are visually imperceptible. This thesis reports techniques and technologies developed …

Energy Conversion System For Travelers (Ecost), Thipok Bovornratanaraks

The International Student Science Fair 2018

We have innovated “The Energy Conversion System for Travelers” or the ECoST. With the fact that most travelers have wheeled cabin-bags, whilst walking, the wheels will rotate so why don’t we harvest electricity from this kinetic energy? We thus install our innovation, the ECoST, to the bag to generate electricity from the spinning wheels. The electricity is then kept in the storage unit and ready to charge your empty battery devices in an emergency case via a USB port. To make life easy, our ECoST was designed to replicate the power bank charging method; therefore, we can charge …

Effects Of Methyl-Blue Addition In Sewage Substrate On The Performance Of Microbial Fuel Cell, Joseph H. Kihedu Dr.

Tanzania Journal of Engineering and Technology (TJET)

Experimental study was undertaken to evaluate performance of microbial fuel cell. Without addition of methyl blue, the cell generated 1.265 V, 0.403 mA and 56.12 mW/m2 after three hours of operation. With 300 µM methyl blue in sewage anolyte, 6.7% increase in voltage, 20.5% increase in current and 28.6% increase in power density was observed. By using ash water catholyte, addition of methyl blue in anolyte led to increase of 9.0% in voltage, 38.5% in current and 50.9% for power density. Between three and twenty four hours of continuous operation of the cell with phosphate buffer catholyte, the average voltage …

Verification Of Brand Authentication Technology Using Infrared Light And Image Processing, Thomas Fenner, Kevin Whalen, Josh Oliver

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Laser Triangulation Sensor, Jake Finelt, Kian Gruszczynski, Greg Mclorg

Mechanical Engineering

Statement of Disclaimer: Since this project is a result of a class assignment, it has been graded and accepted as fulfillment of the course requirements. Acceptance does not imply technical accuracy or reliability. Any use of information in this report is done at the risk of the user. These risks may include catastrophic failure of the device or infringement of patent or copyright laws. California Polytechnic State University at San Luis Obispo and its staff cannot be held liable for any use or misuse of the project.

3-Dimensional Automated Heat Flux Calibration Device, Victor Raul Chacon, David Madison Morrisset, Alex Michael Schnorr, Kevin Scott

Mechanical Engineering

This document aims to describe the problems in current radiant heat source heat flux calibration techniques and the approach our team took to solve them through automation. The following sections outline the basic premise of the problem we addressed and who our end product benefited. The proceeding sections addresses the research that we have performed regarding heat flux measurements and automation. This research includes current solutions – mostly partial solutions for problems that are similar but not exactly like ours. Following the background research, we define objectives, with specific details that outline how we evaluated different possible solutions, and how …

Bicycle Power Meter, Andrew Mcguan

Computer Engineering

A power meter is a cycling training tool used to record the power a rider is outputting. This is very useful to athletes who regularly do bike workouts, because the power output is a consistent measure of the rider’s effort level, and is not affected by outside factors such as wind or road gradient. If a cyclist does a workout with the intent to carry a certain speed for a certain amount of time, a strong headwind will slow them down and make them work harder to maintain the same speed, defeating the goal of the workout. When a power …

Farmbot Trackless Redesign, Cole Thomas, Cailey Kamm, Clayton Alderson, Otto Akerstrom

Industrial and Manufacturing Engineering

For this project the team PLANT3D worked along with Rory Aronson and FarmBot to generate a cheaper more user-friendly design for the FarmBot Genesis 1.3. Working with Rory and FarmBot, we as a team generated a list of design requirements and engineering specifications for the project. These requirements centered around creating a more accessible FarmBot model for the average person to be able to purchase and set up with ease. Much of this required taking the existing system and eliminating the most common problem areas. These were the track system, built using 1.5 meter aluminum extrusions and the complex interchangeable …

Dynamics Simulation And Optimal Control Of A Multiple-Input And Multiple-Output Balancing Cube, Felix K. Haimerl

Master's Theses

This thesis document outlines the development of a multibody dynamics simulation of an actively stabilized multiple-input, multiple-output, coupled, balancing cube and the process of verifying the results by implementing the control algorithm in hardware. A non-linear simulation of the system was created in Simscape and used to develop a Linear Quadratic Gaussian control algorithm. To implement this algorithm in actual hardware, the system was first designed, manufactured, and assembled. The structure of the cube and the reaction wheels were milled from aluminum. DC brushless motors were installed into the mechanical system. In terms of electronics, a processor, orientation sensor, motor …

Chemotherapeutic Drug Cytotoxicity Measurement With A 3d Biomimetic Microfluidic Device And Computational Fluid Dynamics Model, Maryam Moarefian, Caroline Jones, Luke Achenie, Danesh Tafti

Biology and Medicine Through Mathematics Conference

No abstract provided.

A Microresonator-Based Laser Doppler Velocity Sensor For Interplanetary Atmospheric Re-Entry, Benjamin Wise

Mechanical Engineering Research Theses and Dissertations

In this thesis, a laser velocity sensor concept based on optical microresonators is presented and the application to spacecraft atmospheric entry is explored. The concept is based on the measurement of Doppler shift of back-scattered laser light. Specifically, the Doppler shift is detected by observing the whispering gallery optical modes (WGM) of a dielectric microresonator excited by the back scattered light from particulates and gas molecules. The microresonator replaces the typical Fabry-Perot interferometer and CCD camera system, thereby significantly reducing the size and weight of the overall detection system. This thesis presents proof-of-concept results for this measurement approach. The Doppler …

Modeling Of Swimming Cells From Nano-Scale To Micro-Scale, Yicheng Zhao

McKelvey School of Engineering Graduate Student Theses & Dissertations

Certain human genetic diseases -- primary ciliary dyskinesia, infertility, and hydrocephalus -- are characterized by changes in beat frequency and waveform of cilia and flagella. Chlamydomonas reinhardtii, which is a single-cell green alga about ten micrometers in diameter that swims with two flagella, serves as an excellent biological model because its flagella share the same structure and genetic background as mammalian cilia and flagella. This study uses the finite element method to investigate the behavior of C. reinhardtii swimming from nano-scale to micro-scale. At the device-level, micro-scale modeling indicates that well-designed acoustic microfluidic devices can be used to trap groups …

Digital Enhancement Of Analog Measurement Systems For Temperature Compensation Of Strain Gages, Islombek Karimov

Electrical Engineering Theses

Generally known temperature compensation techniques for strain gages (like the use of a dummy gage or the implementation of half- and full-bridge configurations) are not applicable to all strain-measurement situations and cannot fully compensate for all sources of error. Digital Enhancement of Analog Measurement Systems presents a universal method of corrections for these effects in which temperature is measured independently of other variables and ex post facto corrections are computed and applied to digitized readings of the analog measurement system.

A single, linear-pattern strain gage, self-temperature-compensated for steel 1018, has been utilized in a quarter-bridge to measure tensile strain in …

Microheater Array Powder Sintering (Maps) For Printing Flexible Electronics, Nicholas Holt

Graduate Theses and Dissertations

Microheater array powder sintering (MAPS) is a novel additive manufacturing process that uses an array of microheaters to selectively sinter powder particles. MAPS shows great promise as a new method of printing flexible electronics by enabling digital curing of conductive inks on a variety of substrates. MAPS operation relies on establishing a precision air gap of a few microns between an array of microheaters, which can reach temperatures of 600°C, and a layer of conductive ink which can be deposited onto a flexible substrate. This system presents challenges, being: the fabrication of a microheater that can reach suitable temperatures in …

Fluid Phase Separation Via Nanochannel Array, John Lee

Graduate Theses and Dissertations

Microelectromechanical systems (MEMS) and nanoelectromechanical systems (NEMS) generate ideas and techniques for creating new devices at the micro/nano scale. This dissertation study designed a gas generator system utilizing nanochannels for phase separation that is useful for micro-pneumatic actuators, micro-valves, and micro-pumps. The new gas generator has the potential to be an integral part of a propulsion system for small-scale satellites. Nano/picosatellites have limited orientation capability partly due to the current limitations of microthruster devices. Development of a self-contained micro propulsion system enables dynamic orbital maneuvering of pico- and nano-class satellites.

Additionally, the new gas generator utilizes a high efficiency, green …

Baseline Data From Servo Motors In A Robotic Arm For Autonomous Machine Fault Diagnosis, Jacob Brown

Mechanical Engineering Undergraduate Honors Theses

Fault diagnosis can prolong the life of machines if potential sources of failure are discovered and corrected before they occur. Supervised machine learning, or the use of training data to enable machines to discover these faults on their own, makes failure prevention much easier. The focus of this thesis is to investigate the feasibility of creating datasets of various faults at both the component and system level for a servomotor and a compatible robotic arm, such that this data can be used in machine learning algorithms for fault diagnosis. The faults induced at the component level in different servomotors include: …

Numerical Simulation Of A High Strain Rate Biaxial Compression Apparatus, Michael Lagieski

McKelvey School of Engineering Graduate Student Theses & Dissertations

Few experimental methods today are capable of exploring the strength of materials at high strain rates (10⁵ s^-1). Those that are capable, such as the Split Hopkinson Bar, Taylor Anvil and Plate Impact suffer from instability and are generally limited to one dimensional wave propagation. Of particular interest is material response under biaxial compression, similar to that seen in inertial confinement fusion. Laser fusion fuel pellets typically undergo large strain rates as well as plastic deformation and non-linear behavior. This work briefly outlines an experimental procedure designed to replicate these large strain rates under biaxial compression using …