Electro-Mechanical Systems Commons^™

Improving The Reliability And Performance Of A Supersonic Indraft Tube Wind Tunnel, Christian J. Kaml

Master's Theses

Access to supersonic testing is increasing in demand, and wind tunnels remain one of the safest and most cost-effective methods for gathering high-speed flow data. Despite being more economical than alternative options, supersonic wind tunnel facilities often require substantial investment to construct, operate, and maintain.

The novel indraft tube tunnel architecture was conceived as a high-speed flow testbed that incorporates features of both Ludwieg tubes and indraft wind tunnels to maintain costs low enough to be accessible even to small universities. This design was first developed and tested in 2018 at California Polytechnic State University, featuring a cost per test …

Evaluation Of Quantification Methods Applied To Overlapping Ftir Features, Benjamin P. Diehl

Reviews, Analyses, and Instructional Studies in Electrochemistry (RAISE)

Quantifying overlapping FTIR spectral features is critical for electrochemical analysis but often requires complex deconvolution. This work systematically evaluates several area ratio and proxy-based quantification methods using a controlled synthetic spectral model with varying signal-to-noise ratio, peak spacing, width, background, and data resolution. Constrained peak fitting and fixed-window integration consistently exhibit near-perfect monotonicity (Spearman ≈ 1.000) and linearity (Pearson ≈ 0.999–1.000) across all conditions. In contrast, derivative and moment-based metrics show sensitivity to peak overlap, width, and background. These results demonstrate that physically grounded area-based methods provide the most robust and reliable quantification of overlapping FTIR features.

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Control Of Ferroelectric And Dielectric Properties Of Undoped, Fe, And Nb-Doped Single-Crystalline (001) Oriented Pb (Zr0.5ti0.5) O3 Thin Films, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

While several factors that influence the properties of ferroelectric devices have been extensively studied in bulk ceramics and polycrystalline thin films, limited is known about the same on single crystalline thin films which have great potential in memory and energy applications. This knowledge gap is largely due to the limited availability of substrates with lattice parameters suitable for supporting high-quality epitaxial growth. In this study, undoped, Fe-doped, and Nb-doped (001)-oriented Pb(Zr₀.₅Ti₀.₅)O₃ thin films were deposited using pulsed laser deposition, each with a SrRuO₃ bottom electrode and a PrScO₃ substrate. The doping concentration used is 1% for both Fe and Nb. …

Comprehensive Review Of Sensible Thermal Storage Systems For Cooking Applications, Anna K. Shariishoy

Tanzania Journal of Engineering and Technology (TJET)

This paper reviewed the sensible thermal storage systems specifically designed for cooking applications. The review focuses on the characteristics of storage materials, their practical applications, and the overall performance of the systems. The review consolidated an array of experimental and numerical research published across various sources such as journals, conferences, books, online resources, and professional reports. A systematic review is used to reach the conclusion of this paper. Significant findings from this study include the wide range of storage capacities attained from small-scale systems that can store ~1–5 MJ of energy for a single meal to bigger systems that can …

Predicting The Influence Of Aggregate Size And Distribution On Cementitious Concrete Properties: A Review, Innocent J. Macha

Tanzania Journal of Engineering and Technology (TJET)

Cement concrete has been in use for centuries as one of the primary construction materials. Its demand in the construction industry is expected to continue for several centuries before the full development of alternative products. However, one of the main areas of research interest is understanding how its constituents can be tailored to make its properties predictable to reduce risks associated with structural failures, reconstruction and reduced durability. These hindrances associated with cementitious concrete result from several attributes, including constituent material characteristics, mixing ratios and workmanship. Understanding the predictability of cement concrete properties requires computer modelling tools to provide reliable …

Root Cause Analysis Of Performance Degradation For An Xyz Thermal Power Plant In Tanzania, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Thermal power plants in Tanzania have been experiencing performance degradation, typically arising from component and subsystem failures, which contribute to power system instability and unreliability. This paper presents a case study of the root causes of performance degradation of an XYZ thermal power plant. The study was conducted by reviewing plant documentations, including maintenance and operational data logbooks, and by standardising the approach through the adoption of ISO 14224:2016 for maintenance and reliability data exchange. Data evaluation was carried out using principal component analysis and scree plot analytical techniques to enhance the depth and accuracy of root cause identification. Additionally, …

Effects Of Cutting Conditions On Tool Temperature And Material Removal Rate In Turning Operations, Simon I. Marandu

Tanzania Journal of Engineering and Technology (TJET)

Cutting conditions in manufacturing processes have effects on tool temperature and material removal rate. The objective of this study was to investigate the effects of cutting conditions namely spindle speed, feed rate, depth of cut and tool nose radius on tool temperature and material removal rate in turning operations. A total of 81 experiments were conducted to measure tool temperature and material removal rate in order to determine the effects of cutting conditions on tool temperature and material removal rate using ANOVA and regression analysis. The results show that tool nose radius, depth of cut, and spindle speed are significant …

Optimizing The Processing Temperature For Synthesis Of Silver Nanoparticles Within Cellulose-Wool Keratin Supramolecular Matrix Using Butylmethylimmidazolium Chloride Ionic Liquid, Ngesa E. Mushi

Tanzania Journal of Engineering and Technology (TJET)

To date, the synthesis of silver nanoparticles on the surface of cellulose and wool keratin biopolymer, while dissolved in ionic liquid, is attractive because of its biomedical potential. However, the optimal processing temperature for the nanoparticle formation is unclear. The previously reported temperature of approximately 120°C gives unpredictable results. The current study employs a combination of 50% cellulose and 50% keratin, along with 69 mg of silver chloride, in Butylmethylimidazolium Chloride BMImCl ionic liquid, using a single-pot process to produce a supramolecular film via non-derivatized mechanochemical interactions. The primary objective is to experimentally establish the processing temperature to achieve stable …

Cellulose Recovery From Waste Denim Fabrics Through Indigo Vat Dye Reduction And Spandex Dissolution, Tito N. Venance

Tanzania Journal of Engineering and Technology (TJET)

This study addresses environmental conservation by tackling end-of-life management for post-consumer denim garments through the recycling of cotton fibres from waste denim. The purification process involved dithionite reduction of vat dyes in the presence of an alkali followed by selective dissolution of spandex using N,N-dimethylformamide (DMF). Optimal conditions for dye removal were determined at 90°C for 120 minutes with sodium hydroxide at 25 g/L, sodium dithionite at 6 g/L and PVP at 4.5 g/L, while spandex extraction was achieved using a 5% DMF solution at 70°C for 4 hours. Ultraviolet (UV)-vis spectrophotometric analysis indicated a significant increase in whiteness (DL*). …

Assessment Of Factors Contributing On Early Rotting Of Chromated Copper Arsenate Treated Utility Power Distribution Wood Poles In Tanzania, Innocent J. Macha

Tanzania Journal of Engineering and Technology (TJET)

The study aimed to assess the factors contributing to the premature decay of Chromated Copper Arsenate (CCA) treated utility power distribution wooden poles in Tanzania. Deteriorated poles samples from various regions in Tanzania were analyzed using handheld X-ray spectrometry to quantify the retention of CCA preservative chemicals. The ages of these poles were estimated based on annual growth rings. The findings indicated that premature failure of CCA treated wooden poles is attributed to an imbalance in the chemical composition of the preservative solution. The study found that CuO retention in most samples ranged between 10-18 kg/m3, significant lower that the …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Research On 3d Printing Resin Exposure Properties And Its Application On Centrifugal Microfluidic Platform Based On Fluorescence Detection, Zheng Qiao

LSU Doctoral Dissertations

This dissertation encapsulates significant advancements in the field of SLA 3D printing and centrifugal microfluidics. Central to the research is the development of a novel mathematical model for predicting trapped resin thickness in SLA 3D printing, a groundbreaking contribution that addresses a critical aspect of printing intricate structures. This model, the first to establish a mathematical relationship for resin thickness, is rooted in a comprehensive study of the resin curing process. The research leverages the concept of 'critical dosage' for resin curing, leading to a more refined and theoretically grounded approach for calculating curing thickness. Experimentation further validates the model, …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Nonmetallic Jet Impingement Thermal Management For Power Electronics Via Additive Manufacturing, Reece Whitt

Graduate Theses and Dissertations

The increase in energy demanded by transportation and energy sectors has necessitated highly efficient thermal management for reliable power electronics operations. Conventional cooling techniques are limited by their inability to target switching location hot spot temperatures, leading to non-uniform thermal gradients. These devices, such as cold plates and heat sinks, also utilize heavy metallic structures that can accentuate electromagnetic interferences generated by high voltage switching processes. This work proposes a non-metallic jet impingement cooler for more customized thermal management, while simultaneously reducing the harmful effects of electromagnetic interferences. Additive manufacturing is utilized to enable jet impingement zones to target individual …

Problem Solving Methods For Synthesis Of Physical Principles Of Mechatronic Module Operations In Intelligent Robotic Systems, Nazarov Khayriddin Nuritdinovich

Chemical Technology, Control and Management

The scientific paper investigates the methods for solving problems of synthesis of physical principles of operation of mechatronic modules of intelligent robotic systems are considered.

In addition, it deals with the specifics of the process of synthesis of the physical principles of the operation of mechatronic modules using predicate models, list models and information matrices of physical and technical effects.

It shows the interpretation of the components of the model of the system for the synthesis of the physical principles of operation of mechatronic modules of intelligent robotic systems and automatic control and the features of the synthesis algorithm for …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Detection Of Nucleotides In Hydrated Ssdna Via 2-D H-Bn Nanopore With Ionic-Liquid/Salt-Water Interface, Jungsoo Lee

Multidisciplinary Studies Theses and Dissertations

Accomplishing slow translocation speed with high sensitivity has been the greatest mission for solid-state nanopore (SSN) to electrically detect nucleobases in single-stranded DNA (ssDNA). In this study, a method to detect nucleobases in ssDNA using a SSN is introduced by considerably slowing down the translocation speed and effectively increasing its sensitivity. The ultra-thin titanium dioxide (TiO₂) coated hexagonal boron nitride (h-BN) nanopore was fabricated, along with an ionic-liquid [bmim][PF₆]/2.0 M KCl aqueous (cis/trans) interfacial system, to increase both the spatial and the temporal resolutions. As the ssDNA molecules entered the nanopore, a …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Investigation Of The Electrode Polarization Effect For Biosensor Applications, Anil Koklu

Mechanical Engineering Research Theses and Dissertations

My research focuses on electrokinetic transport. Particularly, in this dissertation, we focus on fabrication and testing of micro electrodes with nanostructured surfaces to minimize the electrode polarization (EP) effects for biosensor applications. In the first study, electrochemical deposition of gold nanoparticles on to planar gold electrodes was used to generate rough surfaces. Dendritic nanostructures that reduced EP up to two orders of magnitude was obtained by optimizing the deposition conditions. These structures also enhanced dielectrophoresis (DEP) response of our bio-chips, making them usable in physiological buffers. In further studies we discovered a universal scaling of EP in the frequency domain, …

A Numerical Simulation Optimizing Droplet Motion Driven By Electrowetting, Jake M. Lesinski

Master's Theses

A numerical simulation of electrowetting on a dielectric was performed in COMSOL to grant insight on various parameters that play a critical role in system performance. The specific system being simulated was the Open Drop experiment and the parameters being investigated were the applied voltage, contact angle at the advancing triple point, and droplet overlap onto neighboring actuated electrodes. These parameters were investigated with respect to their effect on droplet locomotion performance. This performance was quantified by the droplets velocity and the dielectrophortic (DEP) force’s magnitude; the DEP force was calculated from integration of the Maxwell Stress Tensor, however, the …

Effects Of Methyl-Blue Addition In Sewage Substrate On The Performance Of Microbial Fuel Cell, Joseph H. Kihedu Dr.

Tanzania Journal of Engineering and Technology (TJET)

Experimental study was undertaken to evaluate performance of microbial fuel cell. Without addition of methyl blue, the cell generated 1.265 V, 0.403 mA and 56.12 mW/m2 after three hours of operation. With 300 µM methyl blue in sewage anolyte, 6.7% increase in voltage, 20.5% increase in current and 28.6% increase in power density was observed. By using ash water catholyte, addition of methyl blue in anolyte led to increase of 9.0% in voltage, 38.5% in current and 50.9% for power density. Between three and twenty four hours of continuous operation of the cell with phosphate buffer catholyte, the average voltage …

Chemotherapeutic Drug Cytotoxicity Measurement With A 3d Biomimetic Microfluidic Device And Computational Fluid Dynamics Model, Maryam Moarefian, Caroline Jones, Luke Achenie, Danesh Tafti

Biology and Medicine Through Mathematics Conference

No abstract provided.

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Drawing And Twisting Of Graphene Fibers, Gregory T. Lane, Robert J. Sekerak, Isaias Diaz

Mechanical Engineering

The aim of this project was to develop a more automated process for drawing and twisting of graphene fibers than was currently in place. This was implemented by having two chemical baths with variable speed rollers at either end, and intermediate roller to spool fiber between stages, and a twisting cylinder with integral spool to twist the fiber as it is collected. The goal was to have this first iteration deliver a working prototype, however due to manufacturing delays and timing constraints, that will be missed. A second follow-on project would be able to continue the work presented here and …

Swelling-Etching Characterization Of Copper (I) Oxide - Pdms For The Development Of Micro/Nano - Particles Composite Mems Corrosion Sensor, Abdoul Kader Maiga

Graduate Theses and Dissertations

The primary objective for this thesis is to contribute to the understanding of the oxide removal process for a corrosion sensing device. The goal for designing such a device is for monitoring corrosion on metallic structures. The sensing material (6.35mm x 1mm discs) of the device is composed of copper (I) oxide particles mixed in some polydimethylsiloxane (PDMS). The PDMS, “housing,” is meant for controlling the oxidation rate through the sensing material. A solvent was used to facilitate the etchant diffusion through the PDMS matrix. Toluene and acetic acid were the ideal solvent and etchant, respectively, for carrying out the …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Accelerated Testing Method For Pem Fuel Cell Based Uninterrupted Power Supply Systems, Xinyu Huang, Xiaofeng Wang

Faculty Publications

Proton exchange membrane fuel cell based power systems are on the verge of commercialization for a number of niche applications where batteries are traditionally used. Uninterrupted power supply (UPS) for wireless communication towers and broadband network relay utilities is one of the targeted application of fuel cell power systems with capacity ranging from one to serveral kilowatts. It is believed that fuel cell based UPS systems can offer considerable advantage when extended backup time is desirable. In order to replace the well-known battery based UPS systems, the reliability and perofrmance of fuel cell based UPS system need to be thoroughly …