Computer-Aided Engineering and Design Commons^™

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Manufacturing Of A Wooden Tortilla Press: Idea To Production, Glenn H. Walker

Honors Theses

The purpose of this thesis is to document the design, development, and manufacturing of a wooden tortilla press completed as a capstone project through the Center for Manufacturing Excellence (CME). The project follows a structured product development process that began with problem definition and concept development, progressed through design, prototyping, and jig fabrication, and culminated in a full production run on the CME shop floor. A multidisciplinary team, including engineers, a marketer, and an accountant, collaborated throughout the project to support both technical development and manufacturing execution. Project planning and scheduling were established early and maintained throughout the project to …

Lunar Manufacturing Systems And The Role Of Additive Recycling Technologies, Camille A. Newman

Honors Theses

Renewed international interest in sustained lunar exploration has created a growing demand for technologies to support long-duration space exploration. Part of the recent Artemis missions and the Moon to Mars initiative is to improve key mission capabilities and fill critical gaps necessary to sustain lunar habitation. Waste management, recycling systems, and manufacturing systems have been identified as critical technologies that need further development before a sustained mission is possible. This thesis explores the feasibility of an additive manufacturing and recycling system designed to process plastic waste generated during extended lunar habitation. Initial research focused on existing manufacturing and recycling technologies …

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

High Voltage Junction Box For Demonstrator Vehicle, Benjamin Lubowicki, Ryan Dorste

Williams Honors College, Honors Research Projects

Schaeffler, our industry sponsor for this project, is designing a battery pack for a demonstration vehicle that requires a high voltage junction box to route power to the vehicle. The project type is a unique design of a mechanical component, mechanism, and process. Our objective for this project is to assemble provided electro-mechanical components into an enclosure following a provided electrical diagram. The expected deliverables are the following: 3D CAD assembly of final product, FEA analysis of designed components, 2D print of final product, fabrication and assembly of designed parts, technical report documenting design process and installation. The skills required …

Zips Racing Electric Brakes Design, Zachary Koneval, Andrew Thompson, Cory Baczkowski

Williams Honors College, Honors Research Projects

The Zips electric racing team is a collegiate team full of engineering students to make a formula electric car that competes against other universities and their cars. But before the cars make it to competition they go through a series of tests to make sure the car is able to perform in all of the actual competition stages. One of the tests for the cars is the brakes test. Where the car has to lock up all four wheels at once and stop in a square that is on the ground. So in this report we have detailed out our …

The Development Of A One-Shot Learning Machine Learning For Industrial Use With Predictive Maintenance, Conor O Brien

Theses

With the advent of Industry 4.0, Manufacturing operations have become more connected and automated. Modern industrial monitoring technology can monitor the performance of both the sensor utilised and the material under monitoring. This has led to a trend where legacy machines without this technology are being removed from production and/or not included in new reconfigurations of production lines, well before their productive lifespan had ended. A key driver for this is the difficulty in retrofitting Predictive Maintenance (PdM) systems to legacy machines, in part due to the machine-to-machine variation present in older machines. Accounting for this variation in PdM systems …

Crafting Comfort: The Design And Production Of A High-End Poolside Lounge Chair, John Hollis Tackett, Robert Griffis

Honors Theses

This report focuses on the development, design, and manufacturing of the Adjustable Lounge Chair, a high-end poolside lounge chair created to address un-met customer demand in the market. The investigation began with a market analysis to identify sought-after features not currently offered by competitors' products. This analysis drove the design of the chair, which was developed using CAD software, followed by the construction of a physical prototype to validate the concept.

The chair's innovative features include adjustable lumbar support and chair height, as well as a removable face-piece that enables users to comfortably lie prone without straining their necks. These …

Structural Design And Fabrication Of A Test Chamber To Test Ppes For Effective Particle Filtration, Matthew G. Adharsingh

Honors College Theses

This research project aims to design and fabricate a test chamber for testing Personal Protective Equipment (PPE) to ensure effective particle filtration. The chamber has a special purpose, which is to measure ultrafine and submicron particles concentration in the air and test the ergonomic design of PPE based on its effective filtration. The project also considers the environmental aspects of the chamber such as the level of noise and vibration. The chamber will be designed to measure upstream and downstream particle count. Initially, the chamber was going to be made from wood, but the research team encountered difficulties in the …

Rc Baja Project: Suspension And Steering, Chance Hills

All Undergraduate Projects

Students designed and manufactured an RC Baja car to compete in the ASME RC Baja competition. The goal of this section of the project was to create a steering system and suspension system that work together properly with a partner’s chassis/drive train systems during tests and competitions. The car needed to be able to complete in the three events, which are a drag race, a solemn course, and the Baja event. The RC will also be evaluated on the ability to climb inclines, top speed, and withstand the drop test. This proposal will explain all the details and effort that …

Quickcut Waterjet Cutter, Kennedy Dunn, Jacob Storrow, Benjamin Laughrey

Williams Honors College, Honors Research Projects

The QuickCut Waterjet Cutter was created in 2019 as a senior design project. This is the third iteration of the waterjet cutter. The goal of this project was to create an operable CNC waterjet cutter that is able to cut 1/16” tensile specimens consisting of nonferrous metal or plastic. This machine will be utilized in the Manufacturing Laboratory at the University of Akron to provide education to interested students on the waterjet cutting process, how it operates, and industrial application of the technology. Waterjet cutting is a subtractive manufacturing process which is recognized for its specialized applications such as cutting …

Adjustable Height Pedestal Grinder Stand, Josef Zagorski, Zachary Wedel, Michael Sitar, Daniel Zevenbergen

Mechanical Engineering

Pedestal grinders are one of the most common machines found in machine shops today. The current industry standard for mounting a grinder is on a fixed single pillar, cast iron pedestal. A fixed pedestal allows for no vertical adjustment for shop users of different sizes and is a safety hazard. This report further defines this problem and proposes an iterative design process to meet the needs and wants of the customer. The adjustable-height pedestal grinder stand Senior Project team used this problem and design process to successfully complete the project within the allotted time. The first major deliverable and milestone …

Configurable Seat Track Latching Mechanism, Emily Sun, Kai Quizon, Rick Hall, Daniel Turn, Nicholas Holman, Alexander Kuznik, Jacob Winkler, Audrey Trejo, Phoebe Zeiss, Steven Kam

Mechanical Engineering

The reconfigurable seating system is a flexible seating solution for transit vehicles that allows operators to change the configuration of the floor plan in a timely manner in order to accommodate change in needs. This project consists of three senior project teams each working on a component of the design: system, track & latch, and articulation. Descriptions of the responsibilities of each team will be discussed below.

Asme Rc Baja Racer, Chesna Kern

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) holds a competition at their annual conference for college students to design an RC car that will compete in sprint, slalom, and obstacle course races. The RC Baja car was designed to complete every event in the competition with a focus on the obstacle course due to the anticipated impacts inflicted on the project car by jumps and other obstacles. The project was a collaborative effort. This presentation focuses on the chassis and suspension while Gizan Gando will present about the drivetrain. The drop and frontal impact test requirements guided the design process …

Development Of A Heavy-Duty Aluminum Rail Hole Punch Manufacturing Fixture, Reese Hawthorne

Williams Honors College, Honors Research Projects

This report details the development and testing of an improved replacement for a worn manufacturing fixture which was used to position the location of four drilled holes on the outside of a heavy-duty aluminum rail. Commissioned by JohnDow Industries, the new process improves upon the old one by implementing an electro-hydraulic punch and new locating fixture. The new design produced higher quality slots, decreased cycle time by 15%, and aimed to improve the ergonomics of the process for the employees. All these factors contributed to making the aluminum rails a high-quality end product for JohnDow’s customers. Further iteration of the …

Data Analysis To Evaluate The Performance Of Breathing Masks Used For Filtering Nano-Level Particles At Manufacturing Sites, Gracia M. Dardano

Honors College Theses

The work performed in this research aims to evaluate the performance of commercially available breathing masks in filtering airborne nanoparticles at manufacturing sites. Nanoparticles are found virtually anywhere, from dust in a worksite to a simple sneeze. Therefore, they pose a substantial threat to human health as their velocity and volatility are high. This research analyzes if current efforts of breathing masks to hinder nanoparticles are effective, especially at manufacturing sites. Data has been collected in order to analyze the behavior of nanoparticles and to measure nanoparticle levels at manufacturing sites and its working environment. Data is statistical in nature …

2 Degree Of Freedom Robotic Leg, Oded Tzori, Henry Terrell, Adan Martinez

Mechanical Engineering

Professor Xing, an assistant professor at Cal Poly, proposed the 2 DOF Robotic Leg project for this quarter’s senior project class. The project is to build a robotic leg attached at the hip to a stand, which will be used as a teaching tool and eventually help develop Cal Poly’s very own robotic quadruped. Since this project has multiple uses after its completion, there are multiple customers that it must perform well for: the Cal Poly Mechanical Engineering (ME) Department, the ME Lab instructors, and the students. The Scope of Work (Sections 2 & 3) is composed of 2 main …

An Affordable And Portable Palpable System For Sensing Breast Tissue Abnormalities, Cody J. Clarke

Montview Journal of Research & Scholarship

Due to the high cost of equipment and lack of trained personnel, manual palpation is a preferred alternative breast examination technique over mammography. The process involves a thorough search pattern using trained fingers and applying adequate pressure, with the objective of identifying solid masses from the surrounding breast tissue. However, palpation requires skills that must be obtained through adequate training in order to ensure proper diagnosis. Consequently, palpation performance and reporting techniques have been inconsistent. Automating the palpation technique would optimize the performance of self-breast examination, optimize clinical breast examinations (CBE), and enable the visualization of breast abnormalities as well …

Fluid Power Vehicle Challenge - The Incompressibles - Final Design Report, Nicholas Gholdoian, Russell Posin, David Vitt, Alex Knickerbocker, Kyle Franck, Julian Rodkiewicz

Mechanical Engineering

This report provides a comprehensive description of the research, analysis and design work that The Incompressibles have completed thus far in the senior project process. This document includes all the work that The Incompressibles have completed for the team’s Preliminary Design Review (PDR), Critical Design Review (CDR), the work leading up to the 2019 FPVC competiton and the competition results. This report includes the initial research that the team completed for the fluid power competition, first iterations of designs, final iterations of designs, manufacturing results and processes, and finally testing and results from competition. With a new design for the …

High Strollers, Braeden Hammond, Morley Perrin, Reid Bartels, Juan Rodriguez

Mechanical Engineering

This report documents the final product of Jonathon’s new lightweight stroller. The Mechanical Engineering team from Cal Poly, High Strollers, began the project to create a lightweight stroller for the project sponsor, Nina Aguayo, and her son, Jonathon Aguayo, in Fall of 2018. Jonathon is diagnosed with Delayed Brain Development and Hypotonia with some characteristics of Cerebral Palsy. He has a 50lb high intensity stroller to go to and from school. Mrs. Aguayo needed a stroller that is easier to transport while still meeting all of Jonathon’s needs. The re-designed stroller will make leisurely outings for Mrs. Aguayo and Jonathon …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Annuloplasty Mti: Improved Tooling For Annuloplasty Ring Manufacturing, Justin David Smith, Spencer Lee Combs, Luke Edward Maly

Mechanical Engineering

The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Asme R/C Baja Car, Torrie Large

All Undergraduate Projects

How does one build a car? Do they start with the tires and build inward or do they develop separate aspects at the same time? This remote-controlled car was designed and built with the intention of competing in the annual Baja Competition. There are three competitions: sprinting, slalom, and an obstacle course. The suspension system of this car must be designed to support the car for both the physical build and the competitiveness. It must do this without interfering with the drive train and steering mechanism designed by Doug Erickson. The suspension system employs suspension arms attached to the chassis …

Additive Manufacturing For Post-Processing, Nathan D. Goodwin, Andrew Furmidge

Mechanical Engineering

Additive Manufacturing for Post Processing (AMPP) is a team comprised of two Cal Poly Mechanical Engineering students: Nathan Goodwin and Andrew Furmidge. The project is focused in the area of metal additive manufacturing (AM) machines, which are still a developing technology. Improvements have been made to the quality of the machines in the past years, but many limitations still exist. One of these is the inability to print parts that are larger than the build volume. In an effort to solve this problem, whole parts are divided into pieces that are printed individually. This team’s senior project is to create …

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

Formula Sae Hybrid Carbon Fiber Monocoque / Steel Tube Frame Chassis, Matthew Hagan, John Rappolt, John Waldrop

Mechanical Engineering

The Cal Poly Formula SAE Team created this project in order to design and fabricate a high-performance chassis which would be competitive at 2013 FSAE Lincoln, and to document the process so that future teams could more easily create a chassis. One of the main goals was to reduce weight from the 143- lb 2012 chassis subsystem. A weight of 95 lb was achieved, with 82 lb in the chassis structure itself and a predicted torsional stiffness of 1700 lb*ft/deg. Composite materials design and manufacturing techniques were developed during the project. Design, testing, and manufacturing processes are detailed, and results …

Process Capability In A Computer Integrated Manufacturing Cell, Andrew Austin

Masters Theses & Specialist Projects

With the rise of automation in traditional manufacturing processes, more companies are beginning to integrate computer integrated manufacturing (CIM) cells on their production floors. Through CIM cell integration, companies have the ability to reduce process time and increase production. One of the problems created with CIM cell automation is caused by the dependency the sequential steps have on one another. Dependency created by the previous step increases the probability that a process error could occur due to previous variation. One way to eliminate this dependency is through the use of an in-process measuring device such as a Renishaw spindle probe …