Computer-Aided Engineering and Design Commons^™

Aerodynamics And Heat Transfer In Polymer Blown Film Processing: Experimental And Numerical Investigation, Mohammad Luqman Zulbakri, Nur Atiqah Mat. Rautin, Raa Khimi Shuib, Ku Marsilla Ku Ishak, Auratus Zuratul Ain Abdul Hamid, Mohamad Danial Shafiq, Mohamad Yusof Idroas, Muhammad Khalil Abdullah

Makara Journal of Technology

The effects of airflow dynamics, heat transfer, and mechanical properties on the HDPE blown film extrusion process were examined using a single-lip air ring with a fixed compressed-air valve opening angle of 10°. Reynolds numbers ranging from 9175 to 25911 were analyzed to understand their impact on cooling efficiency, bubble morphology, and film properties. Numerical simulations employing the Standard k−ω turbulence model in ANSYS FLUENT v2023, with mesh refinement achieving y+ ≈ 1, captured detailed flow and heat transfer behavior. Results showed that higher Reynolds numbers significantly enhanced the heat transfer coefficient, with values increasing from 1096 W/m²·K at Reynold …

Exploration Of Physics-Informed Grid Generation Technique For Wall-Modeled Les Using Eagle3d, Dominic Schneider

Doctoral Dissertations and Master's Theses

Wall-Modeled Large Eddy Simulation (WMLES) is an area of interest due to its ability to lower computational costs of LES. Even with the application of wall models, LES still proves to have practicality issues when it comes to use in industry, due to the expertise, time, and computational resources required. A novel technique for generating a lean, physics based WMLES grid is described.

The technique utilizes a RANS solution to extract turbulence information, user-specified values related to resolution of turbulent energy levels, acoustics waves, and shock waves, to generate a point cloud for producing a lean WMLES grid with in-house …

Piston Crown Design, Kurt L. Lippmann, Liam T. Janssen, Alex Rangel, Larry J. Davis

Mechanical Engineering

This project investigates the effects of dimpling a piston crown, and its impact on engine combustion dynamics. Through computational methods, the effects of piston crown dimpling on flow characteristics were evaluated. Theoretical results were verified with experimental methods. Experimental methods included characterization of exhaust gas content, engine horsepower and torque, and exhaust opacity.

Optimization Of High-Bypass Turbofan High-Pressure Compressor Blade – A Case Study, Adeel Khalid, Vlad Mandzyuk

The Kennesaw Journal of Undergraduate Research

This research determines the relationship between the High-Pressure Compressor (HPC) rotor blade design variables and compressor pressure ratio of a high bypass turbofan engine. Alterations in the HPC blades span, chord, taper, twist, number, and angle of incidence are performed and their effect on the HPC pressure ratio is observed. The objective is to determine key parameters that could maximize the performance of a high-pressure compressor for a given mission. Physics-based modeling, Computational Fluid Dynamics (CFD), and wind-tunnel testing are performed to compare and validate findings. Physics-based modeling is performed to serve as the benchmark for data obtained through other …

Experimentatal And Numerical Investigation Of Turbojet Engine Performance, Emissions, And Noise/Vibrations Using Jet-A And F24 Fuel, John W. Mcafee Jr

College of Graduate Studies: Theses & Dissertations

Drastic improvement in cost effectiveness of high-power computing resources has generated a great interest numerical simulation to reduce the overhead cost of engine manufacturing, maintenance, and environmental concerns of engine testing. To accomplish this goal, this research presents the differences between military F24 fuel and commercial aviation fuel Jet-A from a thermochemical and engine performance perspective. This experimental data was used to create and validate a numerical model of the engine used in the experiments fueled with both Jet-A and F24 fuels. The experimental data was collected using a research based single stage turbojet engine outfitted with many sensors for …

Simulating Steam Jets Due To Rapid Plate Tectonics: A Computational Fluid Dynamics Analysis, Emilie Hatton

Senior Honors Theses

According to the Bible's account of earth's physical history, the majority of geological change from creation to the Ice Age is a consequence of the global Flood cataclysm described in Genesis 6-8. The changes included large-scale tectonic activity, recycling all pre-Flood ocean floor into the mantle, and generating all present-day igneous ocean floor by seafloor spreading at mid-ocean rift zones. Along the middle of these zones, strips of newly formed seafloor were present near the melting temperature of basaltic magma. Above these strips of extremely hot rock, intense jets of steam would almost certainly form. This research seeks to investigate …

A Computational Fluid Dynamic Analysis Of Oxyacetylene Combustion Flow For Use In Material Response Boundary Conditions, Craig Meade

Theses and Dissertations--Mechanical and Aerospace Engineering

Oxyacetylene torches are used in the aerospace industry and research to test thermal protection system materials (TPS) due to their high flame temperatures and high heat flux capabilities. The purpose of this work is to determine a combustion model to accurately simulate the high temperature flow of an oxyacetylene torch. The flow conditions around a sample material can then be used as boundary conditions when modeling TPS material response. Two separate combustion models with equilibrium chemistry were investigated using ANSYS Fluent™; the Eddy-Dissipation Model, and the Partially Premixed model.The results of this study are compared to existing experiments for validation.

Quantifying Shear Stresses In Tissue Engineered Aortic Heart Valves, Raj Nitin Dave

All Theses

Present heart valve prosthesis have limitations such as capability to grow, repair and remodel post implantation. Tissue engineering offers to be a promising alternative to overcome these limitations. Maturation of seeded human cells on the valve subjected to favorable growth conditions in the bioreactor is critical to the success of tissue engineered heart valves. Mechanical stress and strain which results from the pressure and flow conditions in the bioreactor plays a critical role on the developing valve tissue and are currently unknown. The goal of this research is to relate the magnitude of wall shear stress (WSS) within the heart …

Cfd And Heat Transfer Analysis Of Rocket Cooling Techniques On An Aerospike Nozzle, Geoffrey Sullivan

College of Graduate Studies: Theses & Dissertations

In recent years the development of rocket engines has been mainly focused on improving the engine cycle and creating new fuels. Rocket nozzle design has not been changed since the late 1960s. Recent needs for reliable and reusable rockets, as well as advancements in additive manufacturing, have brought new interest into the aerospike nozzle concept. This nozzle is a type of altitude adjusting nozzle that is up to 90% more efficient than bell nozzles at low altitudes and spends up to 30% less fuel. Since the nozzle body is submerged in the hot exhaust gasses it is difficult to keep …

A Parametric Computational Fluid Dynamics (Cfd) Study Of In-Line Horizontal Axis Wind Turbines (Hawts) With Yaw, North Alyster Yates

Masters Theses

Because of the constant use of non-renewable fossil fuels, and the enormous impact they have on global warming and pollution, there has been a push to use more eco-friendly and renewable sources for power. One such form is wind power via turbines. The most common form, Horizontal Axis Wind Turbines (HAWTs), can generate massive amounts of power. However, they also have a serious flaw in their design. As the wind passes through the swept area of the blades and past the tower, it creates massive disturbances in the airflow. These disturbances are called a ‘wake’. When trying to create a …

Design Of A 300cm2 Pemfc Stack With Force And Cfd Simulation To Optimize Flow Channels, Gasket Design, And Clamping Forces., Robert M. Ench

Electronic Theses and Dissertations

Proton exchange membrane fuel cells are important to the future of green energy as hydrogen can be made with green technologies and store energy for later use. Fuel cells can efficiently convert the hydrogen to electricity as needed. This study uses Solidworks simulation to make design improvements to the fuel cell before the prototype build stage of testing; this saves money and time by reducing the prototype builds needed.

In this study, a multi-channel serpentine design with two outlets versus a single outlet is evaluated using CFD to investigate pressure drop. Lower pressure drops are desirable as less energy input …

Flow Characterization In Mine Ventilation Fan Blade Design Using Cfd, Anwar Endris Hassen

Journal of Sustainable Mining

In axial ventilation fans, the generation of a uniform flow velocity is desirable for better efficiency. To that end, different fan blade types have been developed to achieve better flow uniformity. This article aimed to characterize the flow distribution and its uniformity in four blade designs, namely constant chord, tapered blade, skewed blade, and tapered skewed blade, using Computational Fluid Dynamics (CFD). The study employs an iterative study where key study decisions are made as the study progresses. The study began with the selection of a blade profile for the study. A comparative study between the NACA seven-digit and four-digit …

Analysis Of One Way Valve Mechanism For Wings Of A Flapping Drone, Xinchen Deng

Student Works (2020-2029)

The flapping drone is one type of MAVs which is defined as a miniature unmanned aerial vehicle that is inspired by flying birds and insects. Flapping wings can make a perfect combination of thrust and lift by flapping up and down with full usage of unsteady air. The flapping drone has the advantages of high maneuverability and a special lift generation mechanism. Compared with rotary-wing or fixed-wing MAV, it is smaller, lighter, and has higher flight performance. It can quickly change the flight direction and flight speed by control the flapping frequency and it is the only flight mode that …

Cp Check Valve Design, Alec B. Der Matoian, Jessica M. Dent, Skylar M. Tusting

Mechanical Engineering

This report is to serve as a final design review and update to the project sponsors at Zurn Wilkins for the Check Valve Design Senior Project. The senior project team was tasked with improving upon the design of Zurn Wilkins’ backflow prevention assembly for small diameter pipes by reducing the pressure loss created by the check valves within the double check backflow assembly. The information contained in this report builds off the information contained in the Critical Design Report (CDR), as well as feedback and further investigation suggested during an Intermediary Design Review. Based on conclusions from the CDR, our …

Heat Transfer Analysis Of A Data Centre, Arumainathan Kabildev

Student Works (2020-2029)

Data centres are an integral part of networking as it houses servers that facilitate incoming and outgoing data flow. A resolute cooling approach is needed to overcome the hot air dissipated by these servers. This research focused on the computational fluid dynamics (CFD) simulation of the heat transfer modelled upon Telekom Malaysia (TM) City’s data centre 3. The simulation was carried out to ascertain the heat distribution across the data centre by using ANSYS Fluent. The results indicated that the server racks’ inlet temperature reaches 29.79 oC, which is close to the maximum permissible limit according to recommendations provided by …

Three-Phase Hydrodynamic Simulation And Experimental Validation Of An Upflow Anaerobic Sludge Blanket Reactor, Camila D' Bastiani, Jéferson Luis Alba, Gabriel Tomazzoni Mazzarotto, Severino Rodrigues De Farias Neto, Anthony Reynolds, David Kennedy, Lademir Luiz Beal

Articles

This research focuses on performing multiphase solid/liquid/gas CFD simulations of a UASB reactor in order to obtain a validated model that provides a clearer understanding of the hydrodynamic behaviour of the three phases in UASB reactors. Eulerian–Eulerian, laminar, three-dimensional, multiphase simulations are carried out using Fluent 16.2. The liquid phase velocity and flow profile are validated through PIV experiments. A liquid mean velocity difference of 8.45% is found between the experimental and numerical results, thus validating the CFD model. Shadowgraphy is applied successfully to validate the biogas phase velocity and bubble size. Based on the hydrodynamic analysis results, the reactor …

Cavitation Number As A Function Of Disk Cavitator Radius: A Numerical Analysis Of Natural Supercavitation, Reid Prichard

Senior Honors Theses

Due to the greater viscosity and density of water compared to air, the maximum speed of underwater travel is severely limited compared to other methods of transportation. However, a technology called supercavitation – which uses a disk-shaped cavitator to envelop a vehicle in a bubble of steam – promises to greatly decrease skin friction drag. While a large cavitator enables the occurrence of supercavitation at low velocities, it adds substantial unnecessary drag at higher speeds. Based on CFD results, a relationship between cavitator diameter and cavitation number is developed, and it is substituted into an existing equation relating drag coefficient …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Cfd/Fea Of A Steam Methane Reforming Tube, Matthew Wegener

Research Opportunities for Engineering Undergraduates (ROEU) Program 2017-18

Steam methane reforming is the primary method by which hydrogen is produced; increased efficiency in hydrogen production could enable hydrogen’s usage as an alternative fuel. The objectives of this project are to construct a robust CFD/FEA model of a steam methane reforming tube, and to perform CFD/FEA analysis in both steady and transient operational states, comparing thermal stresses/strains in the tube wall in the two states and relating tube stresses/strains to properties of the process controller.

Multiphase Flow Modeling For Design And Optimization Of A Novel Down-Flow Bubble Column, Mutharasu Lalitha Chockalingam

LSU Doctoral Dissertations

The application of the Euler-Euler framework based Computational Fluid Dynamics (CFD) models for simulating the two-phase gas-liquid bubbly flow in down-flow bubble columns is discussed in detail. Emphasis is given towards the modelling and design optimization of a novel down-flow bubble column. The design features of this novel down-flow bubble column and its advantages over a conventional Plunging Jet down-flow bubble column are discussed briefly. Then, some of the present challenges in simulating a conventional Plunging Jet down-flow bubble column in the Euler-Euler framework is highlighted, and a sigmoid function based drag modification function is implemented to overcome those challenges. …

Computational Fluid Dynamics Applied To The Analysis Of Blood Flow Through Central Aortic To Pulmonary Artery Shunts, Carey Celestin Jr

LSU New Orleans Theses and Dissertations

This research utilizes CFD to analyze blood flow through pathways representative of central shunts, commonly used as part of the Fontan procedure to treat cyanotic heart disease. In the first part of this research, a parametric study of steady, Newtonian blood flow through parabolic pathways was performed to demonstrate the effect that flow pathway curvature has on wall shear stress distribution and flow energy losses. In the second part, blood flow through two shunts obtained via biplane angiograms is simulated. Pressure boundary conditions were obtained via catheterization. Results showed that wall shear stresses were of sufficient magnitude to initiate platelet …

Computational And Experimental Study On Vertical Axis Wind Turbine In Search For An Efficient Design, Mohammad M. Bashar

College of Graduate Studies: Theses & Dissertations

Wind alone can fulfill most of the energy requirement of the world by its efficient conversion in to energy. Though Horizontal Axis Wind Turbine (HAWT) is more popular but needs high wind speed to generate energy. On the other hand Vertical Axis Wind Turbine (VAWT) needs low wind speed and can be installed anywhere which are some of the reasons for this research. The main objective of this research is to improve the design and performance of VAWT to make it more attractive, efficient, durable and sustainable. For a VAWT the blades perform the main role to extract energy from …

Feature-Based Neuro-Symbolic Networks For Global Diagnostics, Tracy Lynn Schantz

Electronic Theses and Dissertations

Engineered system diagnostics have been researched over the years with many successful results. From transportation systems to office technologies, many have been equipped with self-diagnostic capabilities and are called Smart Machines. In spite of these advances, current diagnostic systems are driven by direct sensory information without much concern for patterns of the system behavior or features associated with them. For large-scale systems with complex dynamics, global as well as local diagnostics become of great importance, where sensory information is used as input for the local diagnostics, and patterns of behavior or features are utilized for global diagnostics.

The main objective …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …