Computer-Aided Engineering and Design Commons^™

Areosense, Josephine Turney

Williams Honors College, Honors Research Projects

The AeroSense growing system is designed to make indoor aeroponic gardening easy and accessible for everyone. By combining sensors, automation, and AI, the system can monitor and adjust humidity, lighting, and nutrient levels to help plants thrive without requiring expert knowledge. The goal is to create a self-regulating garden that takes the guesswork out of growing fresh herbs and vegetables at home. The project involves building a working aeroponic prototype equipped with misters, pumps, and environmental sensors, all managed by a Raspberry Pi. Using computer vision and machine learning, AeroSense will be able to assess plant health and respond automatically …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Automatic Scoring Cornhole Board System, Eric Diffendal, Jonah Harsh, Connor Lengel, Brett Sukie

Williams Honors College, Honors Research Projects

The objective is to create a self-scoring cornhole board that can detect and calculate each team's score based on the bags thrown each round and to be created at a low cost/eventually being sold at the current cost of a normal board. When playing cornhole, the game is simple: throw a bag on the board; however, the scores are variable (deduct and add) across each round. The most common issue when playing cornhole is miscalculations of the scores and forgetting the correct scores. Thus, this invention will make gameplay easy for all to play.

Autonomous Bottling And Packaging System - Mechanical Bottling Portion, Kathryn Gray

Honors College Theses

This report details the complete mechanical design of an autonomous bottling automation system. This system is fully integrated with a bottling and packaging system. The scope of the full project is to successfully bottle and cap twelve small bottles (approximately 68 cm3) in under three minutes and thirty seconds. The bottles shall be filled with an “electrolyte” and water mixture, and the mixture should be fully mixed. To complete this task, two tanks will dispense liquid (one electrolyte, and one water) into the bottles. Each tank shall have a measuring chamber, that will fill with the correct amount of volume …

Pulse-Width Modulation Spray System Performance And Development Of A Novel System To Optimize Spray Use Efficacy, Prashanta Pokharel

Theses and Dissertations--Biosystems and Agricultural Engineering

The overarching objective of this research was to enhance our understanding of pulse width modulation (PWM) based nozzle control system and develop an intelligent nozzle control system for agricultural spray applications. This dissertation focused on measuring and analyzing the transient nozzle pressure characteristics and performance under PWM control. Additionally, it explored the development of an innovative multi-degree-of-freedom (DOF) nozzle control system for precise chemical applications in specialty crop systems.

The pressure dynamics of a PWM system were studied by developing an instrumentation system capable of operating a solenoid valve and recording pressure signals. A nozzle body and two manifolds of …

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

Rinse Tank Salinity Automation, George Pahoundis

Williams Honors College, Honors Research Projects

Manufacturing processes are often consisted of many different processes and sub-processes. Each of these carries its own level of importance and impact to the overall picture. In this particular sub-process, salt is rinsed from a product via a rinse tank: a tank whose salinity may not exceed a certain level and whose temperature must not fall below a certain level. This setting is a prime opportunity to implement an automated control system to allow these parameters to be met with upmost efficiency. With potential savings in excess of $20,000 per year and an estimated payback period of 8 weeks, the …

Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford

Graduate Theses and Dissertations

This thesis entails motor control system analysis, design, and optimization for the University of Arkansas NASA Robotic Mining Competition robot. The open-loop system is to be modeled and simulated in order to achieve a desired rapid, yet smooth response to a change in input. The initial goal of this work is to find a repeatable, generalized step-by-step process that can be used to tune the gains of a PID controller for multiple different operating points. Then, sensors are to be modeled onto the robot within a feedback loop to develop an error signal and to make the control system self-corrective …

Finding Balance In Generative Product Design, Alex Lobos

Presentations and other scholarship

Generative design develops complex forms and structures similar to those found in nature, taking advantage of automated tasks and high-scale computing power. This approach benefits designers in the creation systems that are efficient, resilient and visually engaging. These systems follow specific rules for form generation and meet clear design goals in terms of shape, strength, mass, and other physical attributes.

There is a large number of methods for creating generative systems, based on establishing desired outcomes and behaviors for how components relate to each other. Examples of methods include L-Systems, Shape Grammars, Swarm Intelligence, Form Optimization, Lattice Design, and many …

Forest Sign Maker, Victor Espinosa Iii, Kevin Ly, Lisa Yip

Mechanical Engineering

Executive Summary:

The Inyo National Forest is arguably one of the most beautiful locations in California, containing natural masterpieces such as Mount Whitney and the Ancient Bristlecone Pine Forest. Despite its magnificence, the Inyo National Forest can be a treacherous region. The Friends of the Inyo take pride in being able to facilitate the viewing experience for all outdoorsmen by maintaining the mountain trails, which includes providing adequate trail signage.

Unfortunately, there is a fundamental issue with the recent state of trail signage in the Inyo National Forest: the rate at which signs are being vandalized or naturally destroyed is …

Design Of An Automatic Wood Trimming Machine, Van Ho, Nicholas Maskal, Andrew Rutland

Mechanical Engineering

This final design report, prepared for Sunrise Arts by the Cal Poly design team Mahogany Automation, details the year-long process in which the team of three engineering students designed and built an automated wooden -plank edge trimming machine that incorporates anti-jamming and continuous loading features. The team has examined current woodworking machines and features available on the industrial and commercial market, and used these as guides along with device requirements set by the project sponsor, Bruce Palmer. The focus has been on designing the simplest and most cost effective device that allows operators to make production runs of wooden slats …

Automating The Fret Slotting Process Using A Plc Controlled 1.5 Axis Mill, James Stratton

Purdue Polytechnic Masters Theses

Stratton, James A. M.S., Purdue University, August 2011. Automating the Fret Slotting Process Using a PLC Controlled 1.5 Axis CNC Mill. Major Professor: Richard Mark French.

Can automation assist small job shops and hobbyists in the production of stringed instruments? This research set out to answer the question using a quantitative approach to determine if an economical CNC machine could be produced in such a fashion as to seamlessly join the workshop as an affordable, yet precise instrument to aid in the production of stringed instruments. The key was to incorporate common industrial automation equipment into the operation of the …