Computer-Aided Engineering and Design Commons^™

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

Pin Router Duplicator, Daniel Phan

All Undergraduate Projects

The purpose of this project is to develop a pin router duplicator to accurately produce guitar bodies, necks, and fret boards. The pin router duplicator is designed to speed up the production process for the class Lean Manufacturing (MET 345), offered at Central Washington University. In the class, students learn how to work as a team to improve the way a woodshop is ran. In Lean Manufacturing, guitar bodies, necks, and fret boards are produced by using a CNC router. For this project, the motivation is to increase production by reducing production time. Accuracy and repeatability is also taken into …

H.F. Hauff Outrigger: Vertical Arm, Juan Tovar

All Undergraduate Projects

H.F. Hauff is a company based out of Yakima which specializes in farming equipment. One of their products is a trailer which has a wind machine attached to it. In order to keep the fan’s thrust from tipping the trailer over, the trailer needs outriggers to extend out. The outriggers also serve as a way to level out the trailer in uneven surfaces. The outriggers are what needed to be designed. This portion of the project was the vertical arm which extends from the horizontal arm, and goes towards the ground to raise the trailer. The project consisted of three …

Orchard Bin Atv Trailer, Neil F. Leitz

All Undergraduate Projects

A local orchardist was experiencing a problem that was being caused by their lack of apple picking bin moving equipment. The orchardist needed a well-engineered solution to this lack of equipment. The solution arrived at was a five bin trailer. There were multiple design requirements for this trailer, including the device needing to be able to interface with an ATV, be able to be loaded by hand, be able to carry five bins, and not exceed a budget of $750. While perfecting the design of the trailer, a number of different disciplines were utilized, which included dynamics, kinematics, static loading …

Grant County Public Utilities District - Rotor Pole Lifting Device, Baylie Johnson

All Undergraduate Projects

Grant County Public Utilities District is planning a rehabilitation of all turbine and generator units at Priest Rapids Dam beginning in August 2016. After the generator rotor is removed from the unit, the rotor poles must be removed from the rotor. They are oriented vertically in the rotor and horizontally on the floor and in shipping containers. The objective of this project is to design, manufacture and test a lifting and a turning device for Priest Rapids Dam’s generator rotor poles. The lifting device was designed to attach a 3500 pound rotor pole to a crane and lift it. The …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …

The Pneumatic Leg Extension, David G. Sedano

All Undergraduate Projects

In recent years, reaching altitudes that are higher than your normal-height has evolved from pure amusement to an “in-demand” necessity out in the field. Means of achieving greater than normal height range from wooden poles to aluminum stilts. The era of ladders and other extension methods are slowly fading away. There are many designs in the market that focus on different factors to make a stilt. As other designs focus on one or two enhancements, the pneumatic leg extension’s objective is to improve all aspects of the stilt. This radical new design differs greatly from traditional stilt designs. The pneumatic …

Conversion Casting: Adapter Hub, Joseph M. Coup

All Undergraduate Projects

The concept of conversion casting makes manufacturing major components much more efficient with regards to time and cost. The conversion cast of the adapter hub used in the Victair Mistifier is a major component that requires 8 hours to machine. The existing hub starts from steel stock and then that block of steel is placed into a CNC machine and coded in to create the adapter hub. The manufacturing method changes to a casting for the adapter hub will create a replicated part that requires 1.5 hours of post machining. The intricate design makes a conversion to casting more effective …

Asme Mini Rc Baja: Drivetrain, Jason M. Moore

All Undergraduate Projects

Title and author: ASME mini RC Baja Drivetrain by Jason Moore; partner Mike Cox. (Engineering Technologies, Safety, and Construction)

Abstract/Artists Statement: The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take …

Shellfish Bag Maker, Trevor R. Reher

All Undergraduate Projects

When commercially harvesting shellfish specifically clams and oyster, plastic mesh bags are commonly used to place shellfish in after harvesting on beaches. The issues is taking the raw bag material used for harvest and cutting it to a specified length. The material comes on a 2000 ft. spool and needs to be cut to a length of 54 in. Using an existing but out dated machine, a bench mark was made that the new design must be 10% more efficient for the customer to invest money into building the machine. Using mechanical machine design and computer designing software the machine …

Flag Raising Device, Josh Quintero

All Undergraduate Projects

The motivation for this project stems from a lifetime of boating with father Richard Jones. One problem that many people encounter, including Richard, was when towing someone behind a boat, is the difficulty with handling the warning flag. This flag is used to show other surrounding boats that someone has fallen into the water behind their boat. This warns other boats to stay far away from that area to keep safe from running over the swimmer. Although, when holding the flag in the boat, it can be hard to see at times. The boat driver, or other people standing in …

Hydraulic Sprayer Boom Upgrade, Chad R. Omlin

All Undergraduate Projects

Title and Author: Agriculture sprayer hydraulic boom upgrade by Chad Omlin (engineering Technologies, Safety, and Construction)

Abstract: Today’s agriculture industry is all about being the most efficient with your time, land, employees, and machinery. One thing that has made farming more efficient has been the use of hydraulics. Having a sprayer unit with manual booms is not being efficient with your time and/or employees. To make the sprayer unit more efficient, hydraulic cylinders were added. Sketched solutions were analyzed using statics and mechanics of materials principles. Drawings were completed for the successful analysis solutions. Solid works software was used to …

Asme Mini-Baja Rc Car (Steering And Suspension Systems), Michael E. Cox

All Undergraduate Projects

The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take apart and repair quickly. These design problems were approached using basic mechanical design concepts such as gear kinematics, spur and bevel …