Computer-Aided Engineering and Design Commons^™

Analysis Of Tower Stringset Replacement From 33 Kv To 66 Kv Considering Sagging Clearance, Muhammad Lazuardi Azzura, Anne Zulfia Syahrial, Julius Purnama Eka Kartika

Journal of Materials Exploration and Findings

Efforts to increase the capacity of transmission networks are often undertaken by uprating the operating voltage of existing lines rather than building entirely new infrastructure. Such uprating typically involves the replacement of tower insulator stringsets to withstand higher voltages, while also ensuring that mechanical performance remains adequate. This paper presents an analysis of uprating the Parakan–Sunyaragi transmission line from 33 kV to 66 kV, with particular emphasis on conductor sagging and the resulting clearance from the ground. The methodology employed includes calculations based on catenary equations, analysis of conductor tensile forces, and a comparative evaluation of two widely used insulator …

Structural Design And Finite Element Analysis Of A 54 Ton Freight Wagon Bolster Test Rig Under Vertical Center Plate Load, Shandy Dwi Prayoga, I Dewa Gede Ary Subagia, I Ketut Adi Atmika, Abdul Rohman Farid, Yunior Lanang Satrio

Journal of Mechanical Engineering Science and Technology (JMEST)

Bolster is one of the bogie's components that receives direct loading from the car body and freight movement. One of the problems that occurs in the bolster is permanent deflection during vertical and transversal static loading. Therefore, a static loading test is required to evaluate the structural strength of the bolster. During the static loading test, a rig is required to hold the bolster so that the bolster is in a fixed position. The rig owned by PT. INKA (Persero) showed a plastic deformation at the vertical center plate load (VCP 5.22P). Therefore, a modified design of the rig is …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Formula Sae Planetary Gearbox Characterization Dynamometer, Trevor Marco Toma, Thomas Welden Pierce, Ethan Liu

Mechanical Engineering

This report outlines a custom hub motor dynamometer requested by the Cal Poly Racing FSAE team. The need for this testing platform is to characterize an existing Formula SAE planetary gearbox for a proposed 4WD powertrain. Hub motors, compact electric machines integrated directly into each outboard wheel, offer significant advantages in efficiency, traction, and chassis packaging compared to conventional RWD drivetrains. By mapping torque capacity, efficiency, lubrication method effectiveness, and fatigue life, the team can validate gearbox design and performance.

This senior project group designed and built a dynamometer according to these specifications which will allow for successful testing to …

Smart Sleeve, Evan Abalos, Bright Jung, Owen Bowling, Wyatt Eberhart

Mechanical Engineering

Quantifying human arm muscle activity is essential for understanding human movements and helping individuals who suffer from motor or neurological impairments such as stroke or traumatic brain injuries. Today, these individuals, as well as clinicians, researchers, and athletes, face many challenges when using the traditional surface electromyography (sEMG) systems to monitor muscle activities, including complex setup, restricted mobility, discomfort, inconsistent placement of electrodes, and lack of accuracy. Therefore, a comfortable EMG sleeve device that accurately measures arm movement without interfering with daily tasks is needed, which the team will be designing, manufacturing, and testing as their senior project. In addition, …

Process Improvement For Thermal Barrier Coating Masking Applications, Katherine Meezan, Aiden Senn, Saksham Giri, Katelyn Perez

Mechanical Engineering

Solar Turbines, a gas turbine manufacturer, needs a more efficient method to prevent the application of a thermal barrier coating (TBC) to select areas of their combustion liners during manufacturing. Currently, the process is labor, material, and time intensive: reusable masking tools should increase the efficiency of the TBC process.

This project is sponsored in full by Solar Turbines, and is under the guidance and administration of three Solar Turbines engineers: Chris Noone, Rick Rogers, and Carson Roff. The project is mentored by Cal Poly senior design Coach, Rick Lasko. This project will be completed by a team of four …

Cal Poly Fluid Powered Vehicle Challenge 2025/2026, Ethan Malachi Nejame Zeiset, Christian Anthony Cuamani, Daniel Chacon-Bizarro, Marcus Minera, Bradley Hansell

Mechanical Engineering

In this Final Design Report, the Cal Poly Fluid Power Vehicle Challenge Contending Team competed in Sun Hydraulics’ 2026 Fluid Powered Vehicle Challenge. The objective of the competition is to expose college students to the fluid power sector, the “hidden giant” of the engineering industry. Specifically, student teams are tasked with the development of a human-powered, fluid-driven vehicle for use in various competitive settings. The team prioritized the optimization of an existing prototype for simplicity, ease of maintenance, and reliability during the competition. The existing prototype exhibited issues related to the main frame’s deflection under load, a lack of gear …

Mars Mini Rover Sample Retrieval Robotic Claw, Cami Chambers, Ani Lachikian, Alexa Ramirez, Alex Power

Mechanical Engineering

This project involves several key stakeholders, including the Poly1 Rover Club, Professor Rich Murray, and NASA’s Jet Propulsion Laboratory (JPL). The primary objective is to develop an improved robotic claw capable of retrieving sample tubes left by the Perseverance Rover on the Martian surface. In tackling this challenge, the design must account for the harsh Mars climate while integrating cameras and electrical components, durable structure, and a rotational component to the Mini-Rover claw without incorporating an additional motor, sample storage unit, structural aspects or unnecessary weight. The current Mini-Rover consists of a four-degree-of-freedom robotic arm with joints often referred to …

Sensory, Light, And Sound Box, Galilea Andrea Portillo, Hannah Elizabeth Henderson, Marcus Kiyoshi Kanenaga

Mechanical Engineering

The Sensory, Light, and Sound Box senior project outlined an adaptable, mobile sensory environment designed to improve cognitive and visual processing skills for students with Cerebral Visual Impairment (CVI) at the Oceano Education Center. Currently, the market lacks accessible solutions tailored to these non-verbal, low-mobility students, making traditional classrooms overwhelming. This project outlines the modification of an existing static layout into a functional, three-sided wooden over-bed frame that accommodates a standard hospital bed. Our team manufactured a structurally stable verification prototype under a $500 budget, integrating slow-closing outward-hinged walls for safety, dual Bluetooth speakers, and a synchronized LED projector that …

Manufacturing Of A Wooden Tortilla Press: Idea To Production, Glenn H. Walker

Honors Theses

The purpose of this thesis is to document the design, development, and manufacturing of a wooden tortilla press completed as a capstone project through the Center for Manufacturing Excellence (CME). The project follows a structured product development process that began with problem definition and concept development, progressed through design, prototyping, and jig fabrication, and culminated in a full production run on the CME shop floor. A multidisciplinary team, including engineers, a marketer, and an accountant, collaborated throughout the project to support both technical development and manufacturing execution. Project planning and scheduling were established early and maintained throughout the project to …

Lunar Manufacturing Systems And The Role Of Additive Recycling Technologies, Camille A. Newman

Honors Theses

Renewed international interest in sustained lunar exploration has created a growing demand for technologies to support long-duration space exploration. Part of the recent Artemis missions and the Moon to Mars initiative is to improve key mission capabilities and fill critical gaps necessary to sustain lunar habitation. Waste management, recycling systems, and manufacturing systems have been identified as critical technologies that need further development before a sustained mission is possible. This thesis explores the feasibility of an additive manufacturing and recycling system designed to process plastic waste generated during extended lunar habitation. Initial research focused on existing manufacturing and recycling technologies …

Introduction To Computer-Aided Design Using Solidworks® : A Structured Approach To Parametric Modeling And Design Intent, Swapnil Moon

Open and Affordable Textbooks

This textbook introduces computer-aided design (CAD) using SOLIDWORKS® through a structured, design-centered approach that emphasizes parametric modeling and engineering reasoning. Rather than focusing solely on software commands, the material develops foundational skills in design intent, constraint-based modeling, and feature relationships to create robust, adaptable models.

The content is organized progressively, beginning with basic sketching and feature creation and advancing to complex part modeling, assemblies, motion studies, and engineering drawings. Each chapter builds upon prior concepts, reinforcing systematic modeling practices and promoting the development of system-level thinking required in real-world engineering design workflows.

Designed for undergraduate students with little or no …

Niu Fsae Brake Rotor Design & Flywheel-Based Test Stand Development, Cody J. Marko, Austin Coyne, Alexander Boyden

Honors Capstones

This project addresses the need for a reliable and validated brake rotor for the Northern Illinois University Formula SAE vehicle following a prior catastrophic rotor failure within the team. Brake rotors in high-performance applications are subjected to significant thermal and mechanical loads, and inadequate design can lead to failure, posing serious safety risks and limiting vehicle performance. To solve this issue, a new brake rotor was designed alongside a dedicated test stand to both improve braking performance and enable experimental validation. The rotor was evaluated using finite element analysis (FEA), including transient thermal and structural simulations, to predict maximum temperature, …

Fsae Bespoke Brake Calipers For Hub Motor Architecture, Connor William Vaughan, Liam Upton Walsh, Bradley Brian Kern

Mechanical Engineering

Brakes are the most critical safety system on any performance vehicle, and as Cal Poly Racing transitions their Formula SAE car from a single rear motor to a four-in-wheel motor setup with regenerative braking, the team identified an opportunity to develop a bespoke brake caliper tailored to their specific needs. This document outlines the research, design, manufacturing, and validation of custom front brake calipers designed to improve upon commercial motorcycle calipers in key areas such as serviceability, mounting rigidity, thermal behavior, mass, and hub motor integration. The resulting design is a two-piece, four-piston, radially-mounted aluminum caliper featuring titanium pistons, toolless …

Cvj Torque Loss Dynamometer, Malaika Sriram, Coleman Brown, Zachary Norris, Logan Mast, Chris Mattis

Mechanical Engineering

This report details the design and results of a dynamometer testing rig built to measure torque losses in constant velocity joints (CVJs) for Cal Poly Racing's Baja SAE team. The rig spins a flywheel connected to articulable CVJs up to 800 RPM using a motor, then decouples it and measures the spin-down rate from 800 to 100 RPM to calculate angular acceleration and torque loss. The data collected from this dyno will be used to inform freewheel packaging for future Baja car development.

Design And Development Of A 12-Degree-Of-Freedom Quadruped Robot, Kai De La Cruz

Master's Theses

This thesis presents the design, analysis, and experimental validation of a 12-degree-of-freedom (DOF) quadruped robot developed as a research platform for legged locomotion and control. The system builds upon the Cal Poly Legged Robotics Group’s prior 8-DOF quadruped, addressing key limitations in manipulability, load distribution, and mechanical robustness by introducing a 3-DOF leg architecture.

The mechanical design emphasizes lightweight construction, structural integrity, and modularity to support future research extensions. Static and dynamic loading models were developed to inform component sizing and material selection. A carbon-fiber chassis and redesigned leg assemblies were fabricated and validated through finite element analysis and physical …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Parts, Logan Trimmer

Harrisburg University Other Works

Presentation covering the broad strokes of the project. The goal was to prove the viability of hybrid/additive manufacturing for high stress automotive applications. This project focused on recreating a piston from an old engine to examine if hybrid manufacturing could be used for such applications. On a small scale, hybrid manufacturing was able to be more cost effective if the costs of the equipment and electricity were ignored. The decision to ignore those costs came from the inability to find accurate prices for industrial casting.

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

Akron Soap Box Derby Super Kids Car, Alexis Schultz, Cooper Sites, Sean Stevenson

Williams Honors College, Honors Research Projects

This project aims to redesign the All-American Soap Box Derby Super Kids vehicle to enhance safety, accessibility, and performance while maintaining full compliance with official regulations. The Super Kids program enables children with physical and cognitive disabilities to race alongside a co-pilot, but the current vehicle design presents challenges in stability, entry/exit accessibility, and control—especially following recent regulation changes that increased vehicle speed. The redesigned car will focus on improved ergonomics, lightweight construction, and structural integrity within a $1,000 budget and a 165 lb weight limit.

An iterative engineering design process will guide the project through research, CAD modeling, FEA …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Virtual Process Modeling Of Metal Additive Manufacturing Basedon Direct Energy Deposition In-Situ Failure, Jachin J. Ramirez

2025 Fall Honors Capstones Projects - Archive

This study builds a mesoscale finite element simulation to examine how internal stresses form during additive metal manufacturing using directed energy deposition. The goal is to track how heat and stress develop layer by layer and determine where a failure criterion could appear during the print. The model uses temperature-dependent material properties for Inconel 718 and a moving heat source defined with custom G-code.

Thermal results are mapped into a mechanical simulation to watch stress accumulate as new layers are added. Different scan paths were tested to determine whether varying heat exposure could reduce the extent of a region exceeding …

Design And Development Of Evacuated Photovoltaic-Thermal Systems For Efficient Cogeneration Of Heat And Electricity, Behnam Roshanzadeh

Mechanical Engineering ETDs

In conventional PV systems, most of the solar energy is dissipated into the environment as heat. Accordingly, hybrid Photovoltaic-thermal systems have been developed to utilize the waste heat from PV cells for various thermal applications. However, most PVT systems suffer from low thermal performance compared to solar thermal collectors, as the absorber plate in PVT systems is partially or fully covered by PV cells. This dissertation focuses on improving the thermal performance of PVT systems by introducing the evacuated PVT systems.

An evacuated-tube PVT system was designed and simulated for domestic hot water supply. The evacuated-tube PVT system demonstrated 40% …

Experimental And Numerical Study On The Influence Of Carbon Fiber Reinforcement On The In-Plane Compressive Properties Of 3d Printed Hexagonal Honeycomb Core Structures, Deon Wallace

All Theses

There is difficulty with numerically replicating the behavior of composite honeycomb core structures numerically due to the trouble of gathering material properties from a hollow structure. Also, complex part geometries and carbon fiber reinforcement strategies can lead to unwanted structural weaknesses and variance in material properties that may not be reflected in numerical analysis when the part is additively manufactured. In this study, edgewise compressive testing is used to characterize the mechanical behavior and performance characteristics of these structures. The experimental results indicate an increase in the Young’s moduli of the honeycomb core structures as carbon fiber concentration increases. However, …

Origami-Inspired Pneumatic Soft Robotic Gripper, Conor J. Schott

Master's Theses

This thesis presents the design and evaluation of a vacuum-actuated, origami-based soft robotic gripper. A custom Sea Urchin crease pattern forms a lightweight folding skeleton that collapses radially under vacuum. The system emphasizes low cost and accessibility through laser cutting, 3D printing, and silicone molding. The Sea Urchin geometry was selected after digital and physical screening of candidate crease patterns for smooth folding, low strain concentration, and uniform inward motion. The folding skeleton is laser cut from 4 mil drafting film and folded into a compliant core. Four membrane configurations were developed: an origami gripper with a 36-inch balloon (Design …

Aerospace Fastener Installation Tool, Anthony I. Berghout, Matthew K. Eggers, Liam Dunsmore, Jose Pardo

Mechanical Engineering

Contamination, particularly in aerospace manufacturing environments, is a significant concern, especially with fastener designs that incorporate torque-rated breakaway pieces for easier installation. These breakaway pieces are also known as pintails. Howmet has tooling that can collect loose pintails during installation, but they have small capacities and are not ergonomic for aerospace technicians. Their current need is for a light and ergonomic tool capable of installing a wide variety of Ergo-Tech® fasteners while having a large capacity to collect pintails and improve aerospace manufacturing methods. For this Critical Design Stage, we have finalized a design that allows Pintails to pass through …

Aluminum Boat Rotation Fixture, Kevin W. Heiskell, Nathaniel M. Conway, James S. Knowles, Austin J. Kehl

Mechanical Engineering

Aluminum fishing boats are widely used for various water-based activities, including fishing, transportation, and recreation. Their lightweight construction makes them ideal for maneuverability, particularly in regions like Australia. However, the manufacturing process presents challenges, specifically the need to weld both the interior and exterior seams of the hull. As the boat’s weight increases during assembly, flipping it becomes difficult and potentially hazardous. Traditional methods such as cranes or forklifts are inefficient and pose safety risks. To address this, our team developed a rotating fixture that secures the boat at two connection points, one at the bow and one at the …

Llnl Raft Flash Pole Redesign, Jack Stangel, Evan Wolfson, Jake Borden, Alexander Meeter

Mechanical Engineering

During research exercises in the ocean, Lawrence Livermore deploys a fleet of rafts outfitted with flash modules affixed to tall poles (in tandem called flash poles) that flash while a photo is taken to act as datums for data collection. The current flash pole design that the LIDSS (Lawrence Livermore Independent Diagnostic Scoring System) team uses is too short to be visible in high seas, not mechanically suited to be made taller, too susceptible to the elements and blunt impact and too difficult to service. We aim to solve these issues.

Micro Mobile Home R3, Roha Y. Ali, Yuka M. Iwashita, Luke C. Douglas, Joshua Q. Le

Mechanical Engineering

Homelessness is an ever-growing issue all around the world. In 2023, over 250,000 or ~40% of all people experiencing homelessness did not have access to shelter spaces in the U.S. [1]. All people have the right to a place where they are safe from violence, crime, and the constant fear that they will be forced out.

Both homeless people and outdoor enthusiasts need a new way to keep themselves and their belongings safe when living outdoors, since existing products do not offer adequate security, portability, or versatility.

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Lidss Raft Battery Pack Integration, Jack Maxwell, Vincent Stevens, Matthew Hoodmaker, Colin Flanders

Mechanical Engineering

Lawrence Livermore National Laboratory is a critical member of the United States Department of Defense. Their Independent Diagnostics Scoring System (LIDSS) uses rafts that operate in the ocean to collect missile test data. Several times a year, the United States will test their Inter-Continental Ballistic Missiles by launching them into the ocean near the Marshall Islands. This is where the LIDSS rafts collect their test data. Our project was centered around re-designing the battery pack used by the rafts. The current battery pack design experiences water ingress problems and is difficult to access. Our re-designed battery pack is waterproof to …