Applied Mechanics Commons^™

Fully Electronic Method Of Measuring Post-Release Gap And Gradient/Residual Stress Of A Mems Cantilever, Andrew Stephen Kovacs

Open Access Dissertations

Smartphones and other wireless devices have become ubiquitous over the past decade, and the RF front-end inside of them has become more complex and disproportionately consumes more power compared to other components. Micro-electromechanical systems (MEMS) have a huge potential to reduce these problems while simultaneously offering superior performance compared to current leading-edge technology. However, MEMS technology has difficulty transitioning from the lab to large-scale manufacturing due to the unpredictability of device lifetime and manufacturability issues. This can be mitigated by investigating how critical material or physical parameters (gap, stress, Young's modulus, material thickness, etc.) vary from manufacturing uncertainties and how …

Asymptotic Modelling Of A Thermopiezoelastic Anisotropic Smart Plate, Yufei Long

Open Access Theses

Motivated by the requirement of modelling for space flexible reflectors as well as other applications of plate structures in engineering, a general anisotropic laminated thin plate model and a monoclinic Reissner-Mindlin plate model with thermal deformation, two-way coupled piezoelectric effect and pyroelectric effect is constructed using the variational asymptotic method, without any ad hoc assumptions. Total potential energy contains strain energy, electric potential energy and energy caused by temperature change. Three-dimensional strain field is built based on the concept of warping function and decomposition of the rotation tensor. The feature of small thickness and large in-plane dimension of plate structure …

Acoustic Manipulation And Alignment Of Particles For Applications In Separation, Micro-Templating, And Device Fabrication, Kamran Moradi

FIU Electronic Theses and Dissertations

This dissertation studies the manipulation of particles using acoustic stimulation for applications in microfluidics and templating of devices. The term particle is used here to denote any solid, liquid or gaseous material that has properties, which are distinct from the fluid in which it is suspended. Manipulation means to take over the movements of the particles and to position them in specified locations.

Using devices, microfabricated out of silicon, the behavior of particles under the acoustic stimulation was studied with the main purpose of aligning the particles at either low-pressure zones, known as the nodes or high-pressure zones, known as …

Synthesis And Formation Mechanism Of Cuins2 Nanocrystals With A Tunable Phase, Chao Yu, Linlin Zhang, Long Tian, Dan Liu, Fanglin Chen, Cheng Wang

Fanglin Chen

Chalcopyrite CuInS₂ (CIS) hierarchical structures composed of nanoflakes with a thickness of about 5 nm were synthesized by a facial solvothermal method. The thermodynamically metastable wurtzite phase CIS would be obtained by using InCl₃ instead of In(NO₃)₃ as In precursor. The effects of the In precursor and the volume of concentrated HCl aqueous solution on the phases and morphologies of CIS nanocrystals have been systematically investigated. Experimental results indicated that the obtained phases of CIS nanocrystals were predominantly determined by precursor-induced intermediate products. The photocatalytic properties of chalcopyrite and wurtzite CIS in visible-light-driven degradation of …

Characterization Of 3d Interconnected Microstructural Network In Mixed Ionic And Electronic Conducting Ceramic Composites, William M. Harris, Kyle S. Brinkman, Ye Lin, Dong Su, Alex P. Cocco, Arata Nakajo, Matthew B. Degostin, Yu-Chen Karen Chen-Wiegart, Jun Wang, Fanglin Chen, Yong S. Chu, Wilson K. S. Chiu

Fanglin Chen

The microstructure and connectivity of the ionic and electronic conductive phases in composite ceramic membranes are directly related to device performance. Transmission electron microscopy (TEM) including chemical mapping combined with X-ray nanotomography (XNT) have been used to characterize the composition and 3-D microstructure of a MIEC composite model system consisting of a Ce_0.8Gd_0.2O₂ (GDC) oxygen ion conductive phase and a CoFe₂O₄ (CFO) electronic conductive phase. The microstructural data is discussed, including the composition and distribution of an emergent phase which takes the form of isolated and distinct regions. Performance implications are considered …

Redox Stable Anodes For Solid Oxide Fuel Cells, Guoliang Xiao, Fanglin Chen

Fanglin Chen

Solid oxide fuel cells (SOFCs) can convert chemical energy from the fuel directly to electrical energy with high efficiency and fuel flexibility. Ni-based cermets have been the most widely adopted anode for SOFCs. However, the conventional Ni-based anode has low tolerance to sulfur-contamination, is vulnerable to deactivation by carbon build-up (coking) from direct oxidation of hydrocarbon fuels, and suffers volume instability upon redox cycling. Among these limitations, the redox instability of the anode is particularly important and has been intensively studied since the SOFC anode may experience redox cycling during fuel cell operations even with the ideal pure hydrogen as …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Fanglin Chen

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

A Sinteractive Ni-Bazr0.8Y0.2O3-Δ Composite Membrane For Hydrogen Separation, Shumin Fang, Siwei Wang, Kyle S. Brinkman, Fanglin Chen

Fanglin Chen

BaZr_0.8Y_0.2O_3−δ (BZY) is an excellent candidate material for hydrogen permeation membranes due to its high bulk proton conductivity, mechanical robustness, and chemical stability in H₂O- and CO₂-containing environments. Unfortunately, the use of BZY as a separation membrane has been greatly restrained by its highly refractory nature, poor grain boundary proton conductivity, high number of grain boundaries resulting from limited grain growth during sintering, as well as low electronic conductivity. These problems can be resolved by the fabrication of a Ni–BZY composite membrane with large BZY grains, which requires the development …

Direct Synthesis Of Methane From Co2-H2O Co-Electrolysis In Tubular Solid Oxide Electrolysis Cells, Long Chen, Fanglin Chen, Changrong Xia

Fanglin Chen

Directly converting CO₂ to hydrocarbons offers a potential route for carbon-neutral energy technologies. Here we report a novel design, integrating the high-temperature CO₂–H₂O co-electrolysis and low-temperature Fischer–Tropsch synthesis in a single tubular unit, for the direct synthesis of methane from CO₂ with a substantial yield of 11.84%.

Benchmarking, Characterization And Tuning Of Shell Ecomarathon Prototype Powertrain, Eric J. Griess

Master's Theses

With the automotive industry ever striving to push the limits of fuel efficiency, the Shell EcoMarathon offers a glimpse into this energy conserving mindset by challenging engineering students around the world to design and build ultra-efficient vehicles to compete regionally. This requires synchronization of engineering fields to ensure that the vehicle and powertrain system work in parallel to achieve similar goals.

The goal for Cal Poly – San Luis Obispo’s EcoMarathon vehicle for the 2015 competition is to analyze the unique operating mode that the powertrain undergoes during competition and improve their current package to increase fuel efficiency. In this …

A Contribution Toward Better Understanding Of Overbanking Tendency In Fixed-Wing Aircraft, Nihad E. Daidzic

Journal of Aviation Technology and Engineering

The phenomenon of overbanking tendency for a rigid-body, fixed-wing aircraft is investigated. Overbanking tendency is defined as a spontaneous, unbalanced rolling moment that keeps increasing an airplane’s bank angle in steep turns and must be arrested by opposite aileron action. As stated by the Federal Aviation Administration, the overbanking tendency may lead to a loss of control, especially in instrument meteorological conditions. It was found in this study that the speed differential over wing halves in horizontal turns indeed creates a rolling moment that achieves maximum values for bank angles between 45 and 55 degrees. However, this induced rolling moment …

Low Temperature, Organic-Free Synthesis Of Ba3B6O9(Oh)6 Nanorods And Ss-Bab2O4 Nanospindles, Rui Li, Xinyoung Tao, Xiaodong Li

Xiaodong Li

Using a low temperature, organic-free hydrothermal technique, single-crystalline barium polyborate Ba₃B₆O₉(OH)₆ (BBOH) nanorods were synthesized. It was found that β-BaB₂O₄(BBO) nanospindles can be achieved by annealing the BBOH nanorods at a relatively low temperature of 810 °C. Transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques were used to characterize these nanomaterials. The formation mechanisms are discussed in conjunction with the crystallographic characteristics and surface energy of the BBOH nanorods and BBO nanospindles. UV-vis absorption spectra demonstrated that both BBOH nanorods and BBO nanospindles are …

Enhance Diamond Coating Adhesion By Oriented Interlayer Microcracking, Habio Guo, Xingcheng Xiao, Yue Qi, Zhi-Hui Xu, Xiaodong Li

Xiaodong Li

In this paper, we report a microcrack toughening mechanism for enhancing the adhesion of diamondcoating. The oriented microcracks were formed within the TiC interlayer to dissipate strain energy and accommodate deformation via the crack opening-closing mechanism, thus enhancing the coating/substrate interfacial toughness. The delamination of diamondcoating was effectively prevented when the parallel microcracks were confined within the interlayer and arrested at interfaces of coating/interlayer/substrate. Density functional theory calculations revealed that the highly anisotropicfracture strength of the TiC phase energetically favors crack initiation and propagation along (100) planes only, which are 54.7° away from the interface. These microcracks are constrained inside …

In Situ Synthesis Of Ultrafine Ss-Mno2/Polypyrrole Nanorod Composites For High-Performance Supercapacitors, Jianfeng Zang, Xiaodong Li

Xiaodong Li

We report a remarkable observation that is at odds with the established notion that β-MnO2 was regarded as an undesirable candidate for supercapacitor applications. The specific capacitance of β-MnO2 can reach as high as 294 F g−1, which is comparable to the best crystallographic structure, like α-MnO2. The key is to substantially decrease the size of β-MnO2 powders to ultra small regime. We demonstrate a facile, simple, and effective approach to synthesizing ultrafine (<10 nm in diameter) β-MnO2/polypyrrole nanorod composite powders for high-performance supercapacitor electrodes. Our observation may encourage a revisit of the other good or even bad candidate …

Structure-Thermal Coupling In Viscoelastic Material In Rubber Bushing Of Vehicle System, Zhengui Zhang

Open Access Dissertations

The objective of this research is to utilize the frequency-dependent viscoelastic material model and characterize the dynamic response of rubber bushing under external excitation. Furthermore, with appropriate modeling, two heat generation mechanisms of rubber bushing are explored and their thermal fields are investigated. Due to the nonlinear force-deflection relationship of the viscoelastic material, finding satisfactory mechanical properties of rubber components still poses a great challenge. However, industry nowadays is in urgent demand for precise finite element analysis (FEA) modeling of rubber components. For example, a proper constitutive relationship of rubber components is critical to providing a reliable and trustable simulation …

2015 Zips Sae Baja Brakes And Throttle System, Philip A. Bennett

Williams Honors College, Honors Research Projects

The SAE Baja student design team at The University of Akron is one of the longest-standing design teams at the university. The purpose of this team is to design, manufacture, test, and race an off-road vehicle within the guidelines of competition established by the Society of Automotive Engineers. The vehicle is made up of a small number of subsystems including frame, drivetrain, suspension, steering, and braking. The following will discuss all aspects of the design process of the braking and throttle system of the 2015 Zips Baja car. This process includes several steps and considerations such as design goals, system …

Mechanistic Modeling Of Cutting Forces In Wavy-Edge Bull-Nose Helical End-Milling Of Inconel 718 Under Different Cooling-Lubrication Strategies, Abdulhakim Ali Sultan

Doctoral Dissertations

“This research presents the results of the development of a mechanistic cutting force prediction model for the wavy-edge bull-nose helical endmill (WEBNHE). The mechanistic model was developed to predict cutting force components and the resultant cutting force in high-speed end-milling of Inconel 718 under two cooling strategies: emulsion and Minimum Quantity Lubrication (MQL). The effects of the cooling strategies are incorporated into the mechanistic model through six cutting force coefficients (K_tc, K_rc, K_ac), and edge force coefficients (K_te, K_re, K_ae), which have been experimentally identified in a separate …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Effects Of Magnetic Field On The Shape Memory Behavior Of Single And Polycrystalline Magnetic Shape Memory Alloys, Ali S. Turabi

Theses and Dissertations--Mechanical Engineering

Magnetic Shape Memory Alloys (MSMAs) have the unique ability to change their shape within a magnetic field, or in the presence of stress and a change in temperature. MSMAs have been widely investigated in the past decade due to their ability to demonstrate large magnetic field induced strain and higher frequency response than conventional shape memory alloys (SMAs). NiMn-based alloys are the workhorse of metamagnetic shape memory alloys since they are able to exhibit magnetic field induced phase transformation. In these alloys, martensite and austenite phases have different magnetization behavior, such as the parent phase can be ferromagnetic and martensite …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

La0.6Sr1.4Mno4+Δ Layered Perovskite Oxide: Enhanced Catalytic Activity For The Oxygen Reduction Reaction, Yarong Wang, Zhibin Yang, Fanliang Liu, Chao Jin, Jiao Wu, Ming Shen, Ruizhi Yang, Fanglin Chen

Faculty Publications

Efficient electrocatalysts for the oxygen reduction reaction (ORR) is a critical factor to influence the performance of lithium–oxygen batteries. In this study, La_0.6Sr_1.4MnO_4+δ layered perovskite oxide as a highly active electrocatalyst for the ORR has been prepared, and a carbon-coating layer with thickness <5 nm has been successfully introduced to enhance the electronic conductivity of the as-prepared oxide. XRD, XPS, Raman, SEM and TEM measurements were carried out to characterize the crystalline structure and morphology of these samples. Rotating ring-disk electrode (RRDE) technique has been used to study catalytic activities of the as-prepared catalysts for the ORR in 0.1 M KOH media. RRDE results reveal that carbon-coated La_0.6Sr_1.4MnO_4+δ exhibits better catalytic activity for the ORR. For the carbon-coated La_0.6Sr_1.4MnO_4+δ, the ORR proceeds predominately via a direct four electron process, and a maximum cathodic current density of 6.70 mA cm⁻² at 2500 rpm has been obtained, …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Faculty Publications

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Stabilizing Electrochemical Carbon Capture Membrane With Al2O3 Thin-Film Overcoating Synthesized By Chemical Vapor Deposition, Jingjing Tong, Fengzhan Si, Lingling Zhang, Jie Fang, Minfang Han, Kevin Huang

Faculty Publications

Development of high-efficiency and cost-effective carbon capture technology is a central element of our effort to battle the global warming and climate change. Here we report that the unique high-flux and high-selectivity of electrochemical silver-carbonate dual-phase membranes can be retained for an extended period of operation by overcoating the surfaces of porous silver matrix with a uniform layer of Al₂O₃ thin-film derived from chemical vapor deposition.

Design Of An Sae Baja Racing Off-Road Vehicle Powertrain, Eric T. Payne

Williams Honors College, Honors Research Projects

No abstract provided.

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Vibration Of Steel-Framed Floors Supporting Sensitive Equipment In Hospitals, Research Facilities, And Manufacturing Facilities, Di Liu

Theses and Dissertations--Civil Engineering

Floors have traditionally been designed only for strength and deflection serviceability. As technological advances have been made in medical, scientific and micro-electronics manufacturing, many types of equipment have become sensitive to vibration of the supporting floor. Thus, vibration serviceability has become a routinely evaluated limit state for floors supporting sensitive equipment. Equipment vibration tolerance limits are sometimes expressed as waveform peak acceleration, and are more often expressed as narrowband spectral acceleration, or one-third octave spectral velocity.

Current floor vibration prediction methods, such as those found in the American Institute of Steel Construction Design Guide 11, Floor Vibrations Due to Human …