Acoustics, Dynamics, and Controls Commons^™

Brush Seal Cycling Test Rig, Angelo J. Reis, Neil M. Bedagkar, Max A. Soury, Eoin K. Lenham

Mechanical Engineering

To prevent backflow from the high pressure compressor stages of their gas turbines to lower pressure regions, Solar Turbines utilizes brush seals along their driveshafts. Due to manufacturing limitations, no shaft is perfectly symmetric about its rotating axis, leading to orbiting that creates asymmetric friction on the shaft through rubbing. With this biased application of friction comes a hotspot on one side of the shaft, causing bowing of the shaft and cascading into an amplified vibrational response. Our goal is to gather data on this phenomenon and offer a potential solution.

Pendulum Wave Generator, Abigail Jocelyn Romero, Paul Staley, Wendy Dong, Kyle Schumacher

Mechanical Engineering

The Cal Poly Mechanical Vibrations Laboratory (Vibes Lab) serves to educate and excite students about mechanical vibrations through hands-on experiments. While the lab contains several relatively complicated technical experiments, it lacks simple demonstrations with immediate visual interest to appeal to audiences with less technical backgrounds. Because of this, faculty desired a fun and interactive demonstration project that could be operated with no prior training. The project chosen for this is a Pendulum Wave Generator which is a set of multiple pendulums with differing lengths that combine to create complex and observable patterns over time. This project was completed by a …

Determination And Limitations Of Blocked Forces In Industrial Settings, Matthew Smither

Theses and Dissertations--Mechanical and Aerospace Engineering

Transfer path analysis methods have been used for decades to determine noise and vibration paths emanating from machinery. In its advent, the machinery source had to be disconnected from the receiver it was attached to in order to gain useful information about each. Further advances in methodology allowed for determining machinery input forces without decoupling them from the structures they were attached to. However, these methods were limited in that the machinery and structures were required to be treated as a system. Thus, any force data obtain was only useful in the configuration it was measured in. Finally, a method …

Quarter Car Suspension Model, Jack Miller, Alexander Eckhardt, Jonathan Lam, Max Gardenswartz

Mechanical Engineering

Dr. Porumamilla, Professor of Mechanical Engineering at Cal Poly, needs a way to demonstrate the concept of base excitation to the mechanical engineering students in the Mechanical Vibrations (ME 318) Lab. A mass-spring-damper model represented by a quarter-car suspension has been selected to represent this concept. A team of four students was assigned to design such a model as a senior design project. This document will explain the testing procedures, how were the results, and if they achieved our requirements. Furthermore, the document will explain how we assemble our product and manufacturing steps. Additionally, Critical Design Report (CDR) design changes …

Modeling The Acoustic Transmission Line With Applied Damping, Connor C. Getz

Master's Theses

The transmission line is an underappreciated style of loudspeaker enclosure characterized by an acoustic labyrinth stemming from the rear of the speaker driver. In practice, the transmission line enclosure produces airy sound uncharacteristic of other styles, at the cost of more pronounced resonant peaks. The most important practical drawback of this loudspeaker enclosure design is the difficulty of properly applying damping to these enclosures. Ideally, this difficulty can be mitigated using an analytical model that accurately predicts the SPL frequency response of a transmission line loudspeaker system for a given geometry and mass of damping material.

This research takes the …

Locking Solar Tracking Bushing, Benjamin James Reed, Andrew Donald Maas, Angel Navarro-Iniguez, John Vincent Bruner

Mechanical Engineering

The contents of this final design review (FDR) outline the progress made by a team of four mechanical engineering students at California Polytechnic State University, San Luis Obispo to solve the problem of torsional galloping in solar tracker panels since the preliminary design review. The project proposed by the sponsor, Christian Friedrich, on behalf of ARaymond is a design for a friction based braking system integrated into a redesigned bushing.

The CDR contains details about the system design, the design justification, the manufacturing plan, and design verification plan. In the system design section, the four manufacturing subsystems (bushing mount, actuation, …

Jet Engine Emissions And Vapor Contrail Reduction Through Increased Combustion Efficiency With The Aim To Mitigate Greenhouse Gases Emissions, Austin J. Brant

Honors College Theses

As society continues to globalize and advance in complexity, the increased demand for business aviation has caused the global travel rate of airlines to increase with each year. With this continual increase in aviation travel, the Federal Aviation Administration (FAA) predicts that the fuel consumption rate is to increase by 1.6 percent as of the year 2025. While this increase in fuel consumption is a positive trait of a thriving aviation community, concerns also arise regarding increased greenhouse gas emissions and enlarged contributions to the greenhouse effect. The most prevalent greenhouse gases associated with jet engine emissions are water vapor, …

A Single-Stage Passive Vibration Isolation System For Scanning Tunneling Microscopy, Toan T. Le

Master's Theses

Scanning Tunneling Microscopy (STM) uses quantum tunneling effect to study the surfaces of materials on an atomic scale. Since the probe of the microscope is on the order of nanometers away from the surface, the device is prone to noises due to vibrations from the surroundings. To minimize the random noises and floor vibrations, passive vibration isolation is a commonly used technique due to its low cost and simpler design compared to active vibration isolation, especially when the entire vibration isolation system (VIS) stays inside an Ultra High Vacuum (UHV) environment. This research aims to analyze and build a single-stage …

Data Acquisition, Analysis, And Modeling Of Rotordynamic Systems, Michael P. Mullen

Master's Theses

Data acquisition systems for rotordynamic analysis and machine vibration were explored for the purpose of replacing the obsolete Bently Nevada ADRE 208 and ADRE for Windows system. These included the development of Matlab based custom data acquisition systems and a user interface. A model of an anisotropic rotor response undergoing transient speed was developed for the rapid prototyping and testing of data acquisition systems. Several methods for the measurement of amplitudes and phase in both the time domain and frequency domain were developed and compared. An alternate data acquisition method which is more inline with industry practices was created for …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Using Transfer Path Analysis And Frequency Based Substructuring To Develop A Robust Vibration Laboratory Dynamic Test Fixture Design Process, Cora Taylor

Dissertations, Master's Theses and Master's Reports

The objective of this research is to determine a robust method for designing shock and vibration laboratory test fixtures that accurately reproduce the field environment for the component of interest. The methods presented in this research examine the boundary conditions presented unto the component of interest through transfer path analysis with the intent of reproducing the next-structure attachment impedance with a laboratory test fixture of one and two attachments. The first method includes only using the next-structure relative motion and stiffness to design a test fixture, while the second method uses an optimization algorithm to develop a lumped parameter model …

Bibliometric Analysis Of Bearing Fault Detection Using Artificial Intelligence, Pooja Kamat, Rekha Sugandhi Dr.

Library Philosophy and Practice (e-journal)

The new industrial revolution called Industry 4.0 is proliferating at its peak. The time is no longer away when the human race is going to witness a huge paradigm shift. Intelligent machines empowered by Artificial Intelligence (AI)will take over the presence of human workers in the industrial manufacturing sector with the target of achieving 100% automation. With the emergence of cut-throat price competition in the product market, it has become equally important to manufacture goods at minimal costs and with the highest quality. Predicting the decrease in machinery efficiency at an earlier stage to accomplish this objective helps to reduce …

Theoretical Study Of Fano Resonance In A Mechanical System, Alex Alberts

Williams Honors College, Honors Research Projects

Resonance conditions are a major area of study in theoretical and experimental investigation. Normally, a resonance condition is characterized by a symmetric shape on either side of the resonance. In some cases, we can observe an asymmetric resonance shape, which is called a Fano resonance. We will study the appearance of Fano resonance in a purely mechanical system. The frequency response of the primary system is approximated using the method of multiple scales focusing on the location of the resonance condition. Then, curve fitting is used to approximate the Fano parameter associated with the system, which provides a measurement of …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Optimization Of Acoustic Soundboard Through Modal Analysis And Material Selection, Noah C. Nicholas, Cody Gruber, Nicholas Hartman

Williams Honors College, Honors Research Projects

The purpose of this design project was to determine if it is plausible to design an acoustic top plate assembly made of a non-traditional material which is equivalent in sound quality to that of a standard wooden guitar. Since wood must be crafted by skilled luthiers, the overall cost of producing the completed product is fairly high. To reduce the cost of a finished acoustic guitar, we proposed to alter the material to that of one that is easier to manufacture, such as plastics and composites.

Based on our research, our team chose to test both ABS plastic and carbon …

Dynamic Behavior Of A Clamped-Clamped Bi-Stable Laminate For Energy Harvesting, Ajay V. Kumar, Andres F. Arrieta Ph.D., Myungwon Hwang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Multi-stable laminates have many applications in morphing structures, energy harvesting devices, and metamaterials due to the specific characteristics attributed to the exhibited stable states. Changes between stable states allow for large deflections, on-demand variation of the stiffness of compliant structures embedded within these elements, and control of effective dynamic properties in periodic lattices. These changes in state can be accessed via a snap-through instability triggered by introducing a well-defined activation energy. The resulting oscillations could enable broadband energy harvesting via piezoelectric transduction and resistive circuits. In this paper, a clamped-clamped bi-stable laminate is studied to understand the behavior of the …

Nonlinear Response And Fatigue Estimation Of Aerospace Curved Surface Panels To Acoustic And Thermal Loads, Adam Przekop

Mechanical & Aerospace Engineering Theses & Dissertations

This work presents a finite element modal formulation for large amplitude free vibration of arbitrary laminated composite shallow shells. The system equations of motion are formulated first in the physical structural-node degrees of freedom (DOF). Then, the system is transformed into general Duffing-type modal equations with modal amplitudes of coupled linear bending-inplane modes. The linear bending-inplane coupling is due to the shell curvature as well as unsymmetric lamination stacking. Multiple modes, inplane inertia, and the first-order transverse shear deformation for composites are considered in the formulation. A triangular shallow shell finite element is developed from an extension of the triangular …