Acoustics, Dynamics, and Controls Commons^™

Design And Implementation Of An Embedded Control System For The Cal Poly Spacecraft Attitude Dynamics Simulator, Neil Mahesh Bedagkar

Master's Theses

This thesis presents the development of a cascaded reaction wheel control system for Cal Poly's Spacecraft Attitude Dynamics Simulator. This work considers system architecture, empirical modeling, high-fidelity simulation, embedded firmware, hardware integration, and experimental characterization. In discrete-time simulation, it is shown that nonlinear direct model reference adaptive control (NDMRAC) enables a nonlinear, partially known plant with realistic actuator dynamics to track the response of a canonical second-order transfer function, with settling time within 4.67% and percent overshoot within order of magnitude of the second-order response. In hardware, the feasibility of a cascaded reaction wheel control architecture is experimentally demonstrated, achieving …

Modeling, Simulation And Control Of Microrobots For The Microfactory., Zhong Yang

Electronic Theses and Dissertations

Future assembly technologies will involve higher levels of automation in order to satisfy increased microscale or nanoscale precision requirements. Traditionally, assembly using a top-down robotic approach has been well-studied and applied to the microelectronics and MEMS industries, but less so in nanotechnology. With the boom of nanotechnology since the 1990s, newly designed products with new materials, coatings, and nanoparticles are gradually entering everyone’s lives, while the industry has grown into a billion-dollar volume worldwide. Traditionally, nanotechnology products are assembled using bottom-up methods, such as self-assembly, rather than top-down robotic assembly. This is due to considerations of volume handling of large …

Dynamic Mode Decomposition Approach For Estimating The Shape Of A Cable, Yash Manik Chavan

Dissertations, Master's Theses and Master's Reports

This study investigates the dynamic behavior of a flexible cable with heterogeneous stiffness using a data-driven approach. The study aims to develop accurate models describing intricate structures with rigid or flexible components. To achieve this, reflective markers were attached to the cable at equal spacing, and the motion was manually excited and captured using an 8-camera setup and OptiTrack's Motive software.

The cable displacement data at the marker locations were used as initial conditions for various Dynamic Mode Decomposition (DMD) models. The performance of the data- driven cable model is compared against the performance of the DMD modeling approach, fitting …

Nonlinear Model Development And Validation For Ball And Plate Control System, Zachary Richter

Master's Theses

Ball and plate balancing control systems are commonly studied due to the complex dynamics associated with the instability of the system in open-loop. For simplicity, mathematical models describing the ball and plate dynamics are often linearized and the effects of complex motion are assumed to be negligible. These assumptions are rarely backed with evidence or explanations validating the simplified form of the dynamical equations of motion. This thesis focuses on developing a nonlinear model that more accurately defines the dynamics of the system, in order to quantify the error of linear and nonlinear models when compared to a Simscape physical …

Computational Study On Suppression Of Airfoil Flow Separation Using High-Frequency Translational Surface Actuation, Bibek Gupta

Honors Theses

Flow separation is a phenomenon that occurs when pressure increases in the streamwise direction of a flow, making a distinctive boundary layer or separation bubble. It causes aircraft to experience an increase in drag and noise and a decrease in a lift, hence degrading their aviation performance. This study uses numerical simulations to understand better the effects of high-frequency translational surface actuation (HFTSA) on flow separation control. The numerical simulations mimic the experimental parameters of an experiment performed by Okoye et al. on using the HFTSA system to control flow separation. A symmetrical airfoil structure of chord length of 0.3 …

Development Of A Method To Model An Enclosed, Coaxial Carbon Nanotube Speaker With Experimental Validation, Suraj Prabhu

Dissertations, Master's Theses and Master's Reports

Carbon nanotube (CNT) speakers operate on heat as compared to conventional loudspeakers that operate on vibration. CNT speakers are extremely lightweight, stretchable, flexible, and have high operating temperatures. Due to these advantages, CNT speakers are being considered as a viable replacement option for conventional loudspeakers. One such application is automotive exhaust noise control. The goal of this research is to design an enclosed, coaxial CNT speaker and to develop a modeling method to model this speaker using COMSOL Multiphysics.

As part of this research, an enclosed, coaxial CNT speaker was designed and manufactured for automotive exhaust noise control. The first …

A Transfer Matrix Model Of The Iec 60318-4 Ear Simulator: Application To The Simulation Of Earplug Insertion Loss, Yu Luan, Franck Sgard, Simon Benacchio, Hugues Nélisse, Olivier Doutres

Études primaires

The IEC 60318-4 ear simulator is used to measure the insertion loss (IL) of earplugs in the ear canal of an acoustical test fixture (ATF) and is designed to represent an average acoustic impedance (in a reference plane) of the human ear. The ear simulator is usually modeled using a lumped parameter model (LPM) which has frequency limitations and inadequately accounts for the thermo-viscous effects in the simulator. The simulator numerical models that can better deal with the thermo-viscous phenomena often lack essential geometric details. Most related studies also suffer from the lack of experimental validation of the models. Therefore, …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

The Simulation For Ultrasonic Testing Based On Frequency-Phase Coded Excitation, Jiaying Zhang, Wenlong Tian, Tie Gang, Sen Cong, Zhaoyang Sheng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

3d Infrastructure Condition Assessment For Rail Highway Applications, Teng Wang

Theses and Dissertations--Civil Engineering

Highway roughness is a concern for both the motoring public and highway authorities. Roughness may even increase the risk of crashes. Rail-highway grade crossings are particularly problematic. Roughness may be due to deterioration or simply due to the way the crossing was built to accommodate grade change, local utilities, or rail elevation. With over 216,000 crossings in the US, maintenance is a vast undertaking. While methods are available to quantify highway roughness, no method exists to quantitatively assess the condition of rail crossings. Conventional inspection relies on a labor-intensive process of qualitative judgment. A quantifiable, objective and extensible procedure for …

The Stability And Control Of The Single Track Vehicles, Shyngys Karimov, Martin Corless

The Summer Undergraduate Research Fellowship (SURF) Symposium

Bicycles, motorcycles and scooters are all examples of the single track vehicles. The dynamics of the single track vehicle involve many degrees of freedom and various modes which govern its performance, making a complicated and interesting research topic. Motorcycle in motion can roll, yaw, and steer about the steering axis. It has three main modes which determine the motion and stability of it, they are weave, capsize, and wobble. The motorcycle performance is limited by the behavior of its modes, and if even one of the modes becomes unstable, the vehicle will roll over, and crash. The goal of this …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …