Acoustics, Dynamics, and Controls Commons^™

Reciprocity-Based Transfer Function Techniques For Acoustic Source Reconstruction, Spring Isolator Characterization And Structural Damping Assessment, David Pum Thian Lal Paite Neihguk

Theses and Dissertations--Mechanical and Aerospace Engineering

Reciprocity implies that a system responds identically when the source and receiver positions are interchanged. This dissertation applies this principle to address three practical challenges in noise and vibration characterization, where conventional approaches are limited by inaccessible interfaces, constrained excitation conditions, or metrics that do not fully capture vibroacoustic behavior.

The first study develops and validates an inverse method to characterize ducted acoustic sources using acoustic free velocity. Acoustic reciprocity is applied to simplify transfer function measurements. The method is extended to large cross-section ducts, where the source is reconstructed as a collection of point sources along a plane. Validation …

Process-Guided Learning Via Data-Driven Modeling And Controller Synthesis, Benton Clark

Theses and Dissertations--Mechanical and Aerospace Engineering

This work introduces process-guided learning, a framework in which process characteristics and learning algorithms are combined in the modeling process of engineering applications with the aim of uniting traditional and data-driven modeling and control techniques. Traditional engineering methods using simplified analytic models fail to capture the increasing complexities of engineering problems with sufficient accuracy to achieve modern requirements. More advanced modeling and control techniques using high-fidelity models often produce a computational burden that is infeasible for real-time solutions. Data-driven modeling offers a simple and flexible algorithm for producing real-time capable, high-fidelity models, but naive implementations lack the physical constraints of …

Extending Low-Frequency Traveling-Wave Propagation In A Water-Filled Cylindrical Waveguide Using Active Impedance Control, William Slater

Open Access Dissertations

This dissertation investigates extending the frequency range over which a one-dimensional, plane traveling wave can be generated in a water-filled, steel-walled waveguide under ocean temperature and hydrostatic pressure conditions. The wave guide considered is a thick-walled, steel cylinder filled with a water/glycol mixture with a transducer at each end and a hydrophone array along the length. One transducer excites a plane wave while the other cancels reflections, resulting in a traveling wave in the waveguide. The current (open-loop) measurement system is advertised to generate traveling waves for low frequencies where only 3.4% of a wavelength can be measured (kL …

Performance Comparison Of A Low Mass Vibratory Lunar Surface Compactor In Vacuum Versus Atmosphere, Robin D. Austerberry

Dissertations, Master's Theses and Master's Reports

As space agencies prepare to return to the moon, an emphasis is being placed on establishing a sustained human presence that requires permanent structures and supporting infrastructure, making site preparation a critical factor. Michigan Technological University’s Planetary Surface Technology Development Lab has developed a novel low-mass surface compaction tool for use on a site preparation vehicle in collaboration with Colorado School of Mines. Testing in vacuum is necessary to simulate a relevant environment, which is required to increase the technology readiness level of this tool to TRL 5. Testing concluded significant interactions between the presence of atmosphere and other factors. …

Nondestructive Evaluation Of Additively Manufactured Parts Using Resonant Inspection And Frequency Domain-Based Correlation Criteria, Gita Deonarain

Dissertations, Master's Theses and Master's Reports

Additive manufacturing (AM) enables the production of highly customized and geometrically complex components; however, these parts remain susceptible to a wide range of defect types and severities. The combination of complex geometries and distributed defects presents a significant challenge for post-process nondestructive evaluation (NDE). Conventional inspection techniques, such as computed tomography and ultrasonic testing, are often limited by geometry, material, accessibility, and cost, while in situ monitoring is not yet sufficiently mature to replace post-process inspection.

This dissertation establishes the Frequency Domain Assurance Criterion (FDAC) as a quantitative, vibration-based framework for defect detection in AM components. FDAC captures spatial–spectral correlations …

Lumacurve Control System Update, Jacob Kustra, Caleb Wengerd

Williams Honors College, Honors Research Projects

The existing track heater control system used by Lumacurve has become outdated and requires frequent maintenance due to inconsistent operation and component failures. This project aims to modernize the system through the implementation of a programmable logic controller (PLC), infrared non-contact temperature sensing, and an automated pneumatic ejection mechanism.

The redesigned system improves temperature monitoring accuracy and reduces operator intervention by automatically ejecting heated plastic tracks from the heater once the desired temperature is reached. An emergency ejection subsystem is also incorporated to safely clear tracks from the heater in the event of improper operation or system faults. Additional emphasis …

Breaking The Vapor Barrier And Scale: Revolutionizing Steel Quenching With Ultrasound Technology, Anthony O. Santos

Williams Honors College, Honors Research Projects

The quenching process is a fundamental heat treatment used to enhance material properties by heating steel to its austenitizing temperature and rapidly cooling it to form high-strength martensite. However, this process is often hindered by two surface barriers: the Leidenfrost effect (vapor blanket) and oxide scale. These cooling limitations restrict the use of steel in high-performance aerospace applications due to inconsistent material properties and unpredictable engineering properties. This research investigates the use of fully submersible, 50-watt 40 kHz ultrasound technology to improve cooling rates in a Jominy test [4]. Through numerical simulations and experimental validation, the study demonstrates that acoustic …

Optimized Returning Floating System (Orfs/Orfeus), Jordan A. Mcclelland, Adam J. Belluardo

Williams Honors College, Honors Research Projects

We are developing a proof-of-concept modified guitar tremolo system for an electric guitar that can automatically optimize tuning adjustments when a player transitions between tuning schemes using a cam system. Currently, changing tunings takes about 10–15 minutes because adjusting the tension on one string affects the tension of the others. Our design aims to compensate for these interactions and significantly reduce the time required to switch tunings.

Akron Soap Box Derby Super Kids Car, Alexis Schultz, Cooper Sites, Sean Stevenson

Williams Honors College, Honors Research Projects

This project aims to redesign the All-American Soap Box Derby Super Kids vehicle to enhance safety, accessibility, and performance while maintaining full compliance with official regulations. The Super Kids program enables children with physical and cognitive disabilities to race alongside a co-pilot, but the current vehicle design presents challenges in stability, entry/exit accessibility, and control—especially following recent regulation changes that increased vehicle speed. The redesigned car will focus on improved ergonomics, lightweight construction, and structural integrity within a $1,000 budget and a 165 lb weight limit.

An iterative engineering design process will guide the project through research, CAD modeling, FEA …

Automated Soil Resetting System For Extraterrestrial Regolith Simulation, Parker W. Brennan, Anthony C. Daniels

Williams Honors College, Honors Research Projects

This project focuses on designing an automated soil resetting system for extraterrestrial regolith simulation. The system will prepare a regolith simulant testbed to a desired, repeatable density, enabling reliable wheel–terrain testing for planetary rover research. Manual soil preparation currently exposes testers to hazardous particulates and produces inconsistent results.

The proposed system will integrate mechanical and control elements to reset the soil bed safely and efficiently. A combination of raking and vibrational methods will be explored, with feedback sensors and automation to achieve target density control. The research will proceed through literature review, benchtop experimentation, prototype design, and full-scale testing over …

Effect Of Kelvin Seamount On Acoustic Propagation, Lindsey Moss

Open Access Master's Theses

This thesis contains CUI. It cannot be distributed, exported, uploaded, or published until it has gone through the proper public release process.