Acoustics, Dynamics, and Controls Commons^™

Torque Vectoring To Maximize Straight-Line Efficiency In An All-Electric Vehicle With Independent Rear Motor Control, William Blake Brown

Theses and Dissertations

BEVs are a critical pathway towards achieving energy independence and meeting greenhouse and pollutant gas reduction goals in the current and future transportation sector [1]. Automotive manufacturers are increasingly investing in the refinement of electric vehicles as they are becoming an increasingly popular response to the global need for reduced transportation emissions. Therefore, there is a desire to extract the most fuel economy from a vehicle as possible. Some areas that manufacturers spend much effort on include minimizing the vehicle’s mass, body drag coefficient, and drag within the powertrain. When these values are defined or unchangeable, interest is driven to …

The Effect Of Noise-Reducing Acoustic Panels On The Noise Levels And Overall Safety Of Infant Sleep Machines, Pranav Poola

Journal of the South Carolina Academy of Science

Infant sleep machines (ISMs) are devices used to help infants fall asleep faster and stay asleep for longer amounts of time, yet they can often be too loud for infantile ears, which could potentially be dangerous. This research aimed to minimize the risks of infant sleep machines without reducing the effectiveness of the infant sleep machines themselves through the use of acoustic panels. Based on previous studies, it was hypothesized that the acoustic panels would reduce the noise levels of the ISM to less than recommended limits of 50 dB-A. A specific corner of a designated room was prepared with …

Nonlinear Model Development And Validation For Ball And Plate Control System, Zachary Richter

Master's Theses

Ball and plate balancing control systems are commonly studied due to the complex dynamics associated with the instability of the system in open-loop. For simplicity, mathematical models describing the ball and plate dynamics are often linearized and the effects of complex motion are assumed to be negligible. These assumptions are rarely backed with evidence or explanations validating the simplified form of the dynamical equations of motion. This thesis focuses on developing a nonlinear model that more accurately defines the dynamics of the system, in order to quantify the error of linear and nonlinear models when compared to a Simscape physical …

Development And Applications Of Adjoint-Based Aerodynamic And Aeroacoustic Multidisciplinary Optimization For Rotorcraft, Ramiz Omur Icke

Mechanical & Aerospace Engineering Theses & Dissertations

Urban Air Mobility (UAM) is one of the most popular proposed solutions for alleviating traffic problems in populated areas. In this context, the proposed types of vehicles mainly consist of rotors and propellers powered by electric motors. However, those rotary-wing components can contribute excessively to noise generation. Therefore, a significant noise concern emerges due to urban air vehicles in or around residential areas. Reducing noise emitted by air vehicles is critically important to improve public acceptance of such vehicles for operations in densely populated areas.

Two main objectives of the present dissertation are: (1) to expand the multidisciplinary optimization to …

Cnc Feed Drive Control, Ryan J. Funchess, Caleb P. O'Gorman, Nick J. Desimone, Juan M. Majano, Samuel K. Wong

Mechanical Engineering

This document serves as the Final Design Report (FDR) for a senior project developed by our team: four senior Mechanical Engineering students and one computer engineering student at California Polytechnic State University, San Luis Obispo (Cal Poly). While the project was completed for, and sponsored by, Professor Simon Xing of Cal Poly, the remainder of the university’s controls professors will be indirectly benefited from this project. Our goal was to design and implement a functional CNC Feed Drive to be used for educational demonstrations and data collection. This document discusses our early product research and benchmark goals, which established constraints …

Adjustable Height Pedestal Grinder Stand, Josef Zagorski, Zachary Wedel, Michael Sitar, Daniel Zevenbergen

Mechanical Engineering

Pedestal grinders are one of the most common machines found in machine shops today. The current industry standard for mounting a grinder is on a fixed single pillar, cast iron pedestal. A fixed pedestal allows for no vertical adjustment for shop users of different sizes and is a safety hazard. This report further defines this problem and proposes an iterative design process to meet the needs and wants of the customer. The adjustable-height pedestal grinder stand Senior Project team used this problem and design process to successfully complete the project within the allotted time. The first major deliverable and milestone …

Vibration Isolation For Scanning Tunneling Microscope, Seth Ewing, Ryan Mcmullen, Jason Behrens, Stephen Deherrera

Mechanical Engineering

Scanning Tunneling Microscopy (STM) works by scanning a fine metal wire over a conductive sample in order to image samples on the atomic level. The microscope uses a feedback loop with a PID controller to maintain a constant tunneling current between the sample and the tip. In order to obtain clear imaging at the atomic level, the microscope and the sample need to be isolated from external vibrations in a vacuum chamber. The scope for this project is to build and test a single-stage vibration isolation system that effectively attenuates the amplitude of external vibrations acting on the microscope. This …

Inverted Fluorescence Microscope, Matthew B. Pfeiffer, Spencer George Hann, Thomas James Eggenberger, Trevor Lee Blythe

Mechanical Engineering

Team F13 is composed of Trevor Blythe, Spencer Hann, Matthew Pfeiffer, and Thomas Eggenberger. We are all majoring in mechanical engineering and in our final year of study here at Cal Poly San Luis Obispo. This project is a continuation of a 2019-2020 senior project. The previous team designed and built a functioning inverted fluorescence microscope (IFM) from scratch. This device was created as a lab tool for undergraduate students to be able to perform experiments on microfluidic devices constructed in Cal Poly’s Microfabrication Laboratory. Although substantially functional, several design constraints had not yet been met. Our team has improved …

3-D Positioning System For Trackable Adjustments Of Papillary Muscles, Ryan Michael Winters, Micaela Andrea Bataclan, Christine Do, Giselle Morales

Biomedical Engineering

Redacted.

Private Sound Environments In Public Space: Use Of Headphones In Public Parks And Public Transit, Chathurthi S. De Silva

Dissertations

The use of headphones is now so commonplace that it is almost second nature for many people to use them. Not only do these people use headphones all the time, but they use them nearly everywhere, including in urban public spaces. In using headphones, people create their own “private sound environments” in public space. This phenomenon merits attention from researchers since the creation of private sound environments may well alter people’s experiences of public space.

This study answers five research questions about the use of headphones in parks and on transit: why people use them, when they begin using headphones …

Classroom Room Acoustics And Effect On Speech With And Without Face Coverings In Direct And Reverberant Sound Fields, Danny Hernandez-Borjas

Symposium of Student Scholars

Prior to the COVID-19 pandemic, life consisted of seeing people in dense public areas such as malls, parks, and schools. But the life these people once knew has changed with face coverings becoming more prevalent in society along with social distancing which caused these public places to limit their capacity. However, a certain faction of society-this being students, have been affected immensely due to this transition of life at school which includes mandatory face coverings in the classroom and social distancing. This research focuses on the effects on speech with and without face coverings in a classroom setting in certain …

Real-Time Monitoring Of Fdm 3d Printer For Fault Detection Using Machine Learning: A Bibliometric Study, Vaibhav Kisan Kadam, Satish Kumar, Arunkumar Bongale

Library Philosophy and Practice (e-journal)

Additive Manufacturing has wide application range including healthcare, Fashion, Manufacturing, Prototypes, Tooling etc. AM techniques are subjected to various defects that may be printing defects or anomalies in machine. There is gap between current AM techniques and smart manufacturing since current AM lacks in build sensors necessary for process monitoring and fault detection. Both of these issues can be solved by incorporating real-time monitoring into AM. So the study is carried out to identify recent work done in AM to improve current system. For this bibliometric study Scopus database is used, study is kept limited to year 2010-2021 and English …

Magnetic Gradient-Based Magnetic Tweezer System For 3d And Swarm Control Of Microswimmer, Xiao Zhang

Mechanical Engineering Research Theses and Dissertations

Microscale manipulation has very promising potential in medical applications such as drug delivery, minimal and invasion surgery. Contactless control is preferable as remote manipulation is necessary for in vivo applications. Among different control methods, magnetic power source is more suitable and robust for the applications mentioned above. Presented here is a magnetic tweezer system, which manipulates microscale magnetic particles using magnetic forces created by magnetic field gradient. The proposed system has three advantages: First, force applied by the magnetic tweezer system does not contact with the target object and can be generated in different directions. Second, the magnetic tweezer system …

Actuation And Control Methods For Individual And Swarm Multiscale Mechanical Systems, Pouria Razzaghi

Mechanical Engineering Research Theses and Dissertations

Robotic mechanisms can be driven by different internally and externally applied inertial and magnetic actuations. These actuations are utilized to regulate the dynamics of robots and move them in different locomotion modes. The first part of this dissertation is about using an external magnetic actuation to move a simple-in-design, small-scale robot for biomedical applications. The robots can be steered in different locomotion modes such as pivot walking and tumbling. The control design of this system consists of a swarm algorithm under a global control input, and a vision-based closed-loop controller to navigate in 2D environments.

Secondly, I propose a new …

A Practical Methodology To Detect, Quantify And Characterize Experimental Uncertainties In The Dynamic Testing Of Structures, James L. Woodall

Civil Engineering ETDs

This thesis investigates the uncertainty in the experimental context of structural dynamics. This thesis proposes a method to estimate both the effect of boundary conditions, as well as two different methods to detect the location of sensors on a specimen. Firstly, this thesis proposes a technique to predict the dynamic behavior of any point along a cantilever beam with an uncertain transverse elastic restraint. Secondly, this thesis investigates the estimation of the location of a sensor given the output data of a physical experiment with two different methods. Small errors in the sensor location may go unnoticed in the frequency …

Simultaneous Thermal Zoning And Demand Control Ventilation, Jose Rodriguez

Mechanical Engineering Theses

Heating Ventilation and Air Conditioning (HVAC) systems include the equipment used to control the conditions and distribution of indoor air in any closed environment that requires certain variables, such as temperature, humidity, carbon dioxide (CO₂) concentration, etc. to be controlled to levels of human comfort and safety, and to levels that keep machines and other devices in special conditions to protect them or guarantee their best performance. In developed countries, HVAC energy consumption is usually between 25% and 42% of the total energy consumption. Thermal zooning and demand control ventilation have shown improvements in comfort and energy consumption savings. The …

Mathematical Modeling Of A Two Wheeled Robotic Base, Kathryn Remell

Mechanical Engineering Undergraduate Honors Theses

This thesis presents the concept of using a two wheeled robot on the moon and briefly explores the requirements for successful long term operation in a lunar environment. The mathematical model for the motion of a robot with two fixed wheels on a differential drive with in a global reference frame. The robot is assumed to be balancing a platform so the mathematical model to balance the platform with wheel motors is also developed and briefly evaluated.

Noise Control In Sorting Conveyors, Eyra Herrera

Mechanical Engineering Undergraduate Honors Theses

E-commerce has increased the necessity of effective material handling equipment in warehouses and distribution centers. Sorter conveyors systems facilitate material handling by providing a reliable and automated system to classify and distribute products in a gentle and rapid manner. With the steady increase of speed in sorter conveyors to satisfy today’s industry demand, some systems have started to produce high noise levels that could potentially affect workers’ health. Since decreasing the speed of these conveyors is not a viable option to decrease noise in sorter equipment, industries have opted to find other ways to apply noise control to their equipment. …

Computational Study On Suppression Of Airfoil Flow Separation Using High-Frequency Translational Surface Actuation, Bibek Gupta

Honors Theses

Flow separation is a phenomenon that occurs when pressure increases in the streamwise direction of a flow, making a distinctive boundary layer or separation bubble. It causes aircraft to experience an increase in drag and noise and a decrease in a lift, hence degrading their aviation performance. This study uses numerical simulations to understand better the effects of high-frequency translational surface actuation (HFTSA) on flow separation control. The numerical simulations mimic the experimental parameters of an experiment performed by Okoye et al. on using the HFTSA system to control flow separation. A symmetrical airfoil structure of chord length of 0.3 …

Développement D'Une Méthode De Mesure De L'Exposition Sonore Effective Intraauriculaire Pour Une Utilisation En Milieu De Travail, Hugues Nélisse, Fabien Bonnet, Marcos Nogarolli, Jérémie Voix

Rapports de recherche scientifique

De nombreux travailleurs sont exposés quotidiennement à des niveaux de bruit susceptibles d'endommager leur audition. De ce fait, la mesure de l'exposition sonore est essentielle afin d'identifier et d’évaluer des solutions correctives pour protéger adéquatement les travailleurs. Cependant, les méthodes et les technologies de mesure actuelles ne permettent généralement pas de déterminer avec précision l'exposition au bruit subie par un individu sur son lieu de travail. La dosimétrie intraauriculaire est une solution prometteuse pour pallier un certain nombre de problèmes liés aux méthodes de mesure conventionnelles, mais cette méthodologie est fragilisée de trois façons : 1) l'exposition sonore mesurée dans …

A Comparative Study Between 6 Degree-Of-Freedom Trajectory Model And Modified Point Mass Trajectory Model Of Spinning Projectiles, Ange Du

Doctoral Dissertations and Master's Theses

For spinning projectiles, the 6 Degree-of-Freedom model can closely capture their trajectories with high accuracy and details. However, it comes with the drawbacks of long computation time and needing many aerodynamic coefficients which can be hard to obtain. The Modified Point Mass Trajectory Model was introduced as a simplified solution. This work compares them with each other, and with some more conventional methods. A program is developed to simulate and visualize trajectories. With some augmentations, the Modified Point Mass model is able to generate comparable results in most cases, but not including special cases such as when the projectile is …

Étude De L’Applicabilité De Haut-Parleurs Paramétriques Au Développement De Nouveaux Concepts D’Alarmes De Recul, Olivier Robin, Alain Berry, Hugues Nélisse

Rapports de recherche scientifique

L’utilisation d’alarmes de recul est obligatoire sur une majorité de véhicules lourds et reste un moyen largement utilisé pour prévenir et alerter les personnes œuvrant à proximité de ces véhicules. Des études antérieures, réalisées par l’IRSST, ont montré les limites d’efficacité des alarmes utilisées en milieu de travail pour minimiser le risque à la sécurité des travailleurs. De plus, les alarmes de recul, par le son de niveau élevé et très typé qu’elles produisent, sont régulièrement une source de nuisance importante pour les travailleurs, et aussi pour les riverains. Ces problèmes de gêne et de perception sonore pour les travailleurs …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Project G.H.O.S.T., Matthew Morell, Austin Conrad, Zackeris Gordon, Conan Estes

Mechanical Engineering

Project G.H.O.S.T aimed to produce a model transmission with a control system for high performance/racing electric vehicles to utilize the full capability of the electric motor at higher speed applications. Current electric vehicles have a large amount of torque and use a fixed gear ratio that compromises between both high and low speeds with performance peaking around 65 miles per hour. A typical electric motor used in this application has approximately 1800 ft-lbs of torque up to 5,000 rpm. Past approximately 5,000 rpm, the torque rapidly drops off and so does the overall vehicle performance. Though transmissions exist that could …

A Feedback-Based Pneumatic Compression System For Effective Lymphedema Management, Mohammad Imrul Kayes

LSU Master's Theses

Bioimpedance analysis (BIA) is a method of detecting lymphedema- a debilitating medical condition involving swelling of the extremities. Pneumatic compression devices are frequently used in the compression treatment of lymphedema. Although existing compression technology provides relief of symptoms, it has limitations in terms of ease-of-use, portability, and monitoring of treatment progress. Currently, there are no BIA analyzers in the market that run on a low-power microcontroller and a rechargeable battery. Moreover, no such device currently exists that integrate the BIA analysis with pneumatic compression system to offer a feedback-based solution for lymphedema treatment. This work represents the first steps towards …

A Single-Stage Passive Vibration Isolation System For Scanning Tunneling Microscopy, Toan T. Le

Master's Theses

Scanning Tunneling Microscopy (STM) uses quantum tunneling effect to study the surfaces of materials on an atomic scale. Since the probe of the microscope is on the order of nanometers away from the surface, the device is prone to noises due to vibrations from the surroundings. To minimize the random noises and floor vibrations, passive vibration isolation is a commonly used technique due to its low cost and simpler design compared to active vibration isolation, especially when the entire vibration isolation system (VIS) stays inside an Ultra High Vacuum (UHV) environment. This research aims to analyze and build a single-stage …

Renewable Energy Production By Solar Chimney: The Influence Of Curved Guide Vanes On The Performance Of A Solar Chimney Using Cfd Simulation, Haokun Xue

Theses, Dissertations and Capstones

The aim of this study is to investigate the effect of the guide vanes on the efficiency of the turbine of solar chimney power plant using Computational Fluid Dynamics (CFD). In this study, a 3-Dimentional CFD simulation of solar chimney power plant based on the Manzanares prototype is performed. The CFD simulation is validated by comparing the experimental data from the Manzanares prototype and simulation data with both 2D and 3D cases. To capture turbulent flow inside the chimney, the SST 𝑘 − 𝜔 turbulence model is used. The first object is to investigate the flow performance under the influence …

Judo Wearable, Alison Waugh, Natalie Masters

Williams Honors College, Honors Research Projects

Design a wearable sensor array to determine if a judo throw fulfills the requirements to win a match

Automated Control System For The Remote-Controlled Torch Positioner, Christopher Ferguson, Anna Abate, Kyle Cramer, Alex Sabitsch, Jacob Stefanko

Williams Honors College, Honors Research Projects

The goal of this project is to design and implement a controls system for Dr. Morscher’s burner rig. The rig serves to simulate jet turbine conditions and test how materials, specifically ceramic matrix composites, react under high temperatures and stresses. Currently, the location of the torch relies solely on manual adjustments and has no automated control system. The improved design will automatically adjust the torch position based on the desired temperature of the sample being tested, therefore maintaining a steady environment for the sample. The current method of manual adjustments for regulating temperature is a crude solution that does not …

Mise Au Point D’Une Méthode De Mesure Objective De L’Effet D’Occlusion Basée Sur La Voix, Hugues Nélisse, Hugo Saint-Gaudens, Franck Sgard, Olivier Doutres

Rapports de recherche scientifique

Lors de l’utilisation de protecteurs auditifs ou de prothèses auditives, le fait d’obstruer le canal auditif peut engendrer un effet indésirable et désagréable, appelé « effet d’occlusion », qui se manifeste notamment par la sensation que notre propre voix sonne différemment, avec de basses fréquences amplifiées, qu’elle est distordue. L’effet d’occlusion est souvent considéré comme une source d’inconfort qui entraîne parfois les utilisateurs de protecteurs ou de prothèses à mal les utiliser ou encore à simplement les retirer. Dans le cas des travailleurs, par exemple, le retrait des protecteurs auditifs peut les exposer à des niveaux de bruits potentiellement dangereux, …