Acoustics, Dynamics, and Controls Commons^™

Active Management Assistant System For Embry-Riddle Ecocar 3 Hybrid Supervisory Control System, Matthew Nelson, Blair Cutting, Michael J. Aleardi

Student Works

The Embry-Riddle EcoCAR 3 team is developing a prototype hybrid Chevrolet Camaro utilizing a customized vehicle powertrain controller. This controller is serving to ensure system safety, vehicle operation, and consumer drivability while also incorporating advanced driving aids to achieve both the desired performance levels one expects from a Camaro as well as vehicle efficiency. This vehicle must reach the team set vehicle technical specifications of a 4.9 second 0 to 60 time while maintaining a 53 miles per gallon gasoline equivalence rating.

In order to reach the efficiency goal, the team is developing an Active Management Assistance System utilizing computer …

3-Axis Automated Probe Traverse For Aerodynamic Testing, Tananant Boonya-Ananta, Ricky Wai, Zander Oostman, Teyvon Brooks

Mechanical Engineering

Our primary objective is to design, build, and test an automated traverse to hold measurement probes in Cal Poly’s low speed wind tunnel. The device should cause minimal flow disturbance. It’s movements must be able to cover eighty percent of the three-dimensional test section. The device should have a mounting point for interchangeable probes. The assembly is to be integrated with the current frame structure on the wind tunnel test section, and should allow very minimal deflection of the measurement probe. The user should be able to control the motion of the traverse via a computer interface which supports automatic …

Optimal Design Of Sound Absorbing Systems With Microperforated Panels, Nicholas Nakjoo Kim

Open Access Dissertations

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles.

This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Design Of A Flexible Control Platform And Miniature In Vivo Robots For Laparo-Endoscopic Single-Site Surgeries, Lou P. Cubrich

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Minimally-invasive laparoscopic procedures have proven efficacy for a wide range of surgical procedures as well as benefits such as reducing scarring, infection, recovery time, and post-operative pain. While the procedures have many advantages, there are significant shortcomings such as limited instrument motion and reduced dexterity. In recent years, robotic surgical technology has overcome some of these limitations and has become an effective tool for many types of surgeries. These robotic platforms typically have an increased workspace, greater dexterity, improved ergonomics, and finer control than traditional laparoscopic methods. This thesis presents the designs of both a four degree-of-freedom (DOF) and 5-DOF …

Dynamic Responses Of Wheel-Rail Systems With Block Dampers, Tzuyu Tseng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The wheel-rail interaction problem has been widely studied in the past few decades. In this problem, dynamic responses at the contact areas remain the central issue since they induce damage to the rail over time. In particular, the dynamic responses at the contact areas between the wheels and rails present difficulties in understanding and mathematical modeling. Even with the computer power one has today, its mathematical modeling employs the versatile numerical analysis method, the finite element method (FEM) remains a formidable challenge due to its extremely small contact areas and in turn the extremely high stress levels. In addition, friction …

Implementation And Performance Evaluation Of Acoustic Denoising Algorithms For Uav, Ahmed Sony Kamal Chowdhury

UNLV Theses, Dissertations, Professional Papers, and Capstones

Unmanned Aerial Vehicles (UAVs) have become popular alternative for wildlife monitoring and border surveillance applications. Elimination of the UAV’s background noise and classifying the target audio signal effectively are still a major challenge. The main goal of this thesis is to remove UAV’s background noise by means of acoustic denoising techniques. Existing denoising algorithms, such as Adaptive Least Mean Square (LMS), Wavelet Denoising, Time-Frequency Block Thresholding, and Wiener Filter, were implemented and their performance evaluated. The denoising algorithms were evaluated for average Signal to Noise Ratio (SNR), Segmental SNR (SSNR), Log Likelihood Ratio (LLR), and Log Spectral Distance (LSD) metrics. …

Extracting Vibration Characteristics Of A Guitar Using Finite Element, Modal Analysis, And Digital Image Correlation Techniques, Kiran Patil, Javad Baqersad, Daniel Ludwigsen, Yaomin Dong

Physics Publications

The sound quality generated by the guitar depends on the vibration characteristics (i.e. natural frequencies and mode shapes) of this instrument. Thus, it is of particular interest to the guitar manufacturers to be able to obtain global information about the characteristics of the guitar. Traditional sensors can only measure at discrete locations. However, digital image correlation (DIC) can measure full-field data on the surface of the structure. In the current paper, a finite element (FE) model of a guitar with free boundary configurations was developed using quadratic solid elements. An eigensolution was performed on the FE model to determine its …

A Bioinspired Modification For Uas Propeller/Rotor Noise Reduction, Mark N. Callender

ASA Multidisciplinary Research Symposium

This projects presents a bioinspired modification to UAS propellers/rotors for noise reduction. Sound pressure levels (SPL) and thrust for modified propellers were compared to a baseline propeller. The bioinspired modification yielded lower SPL with a requisite increase in rpm in order to maintain a chosen level of thrust.

The Simulation For Ultrasonic Testing Based On Frequency-Phase Coded Excitation, Jiaying Zhang, Wenlong Tian, Tie Gang, Sen Cong, Zhaoyang Sheng

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Frequency Based Noise Coherence-Function Extension And Application To Passive Bottom-Loss Estimation, Lanfranco Muzi, Martin Siderius, Peter L. Nielsen

Electrical and Computer Engineering Faculty Publications and Presentations

Accurate modeling of acoustic propagation in the ocean waveguide is important to SONAR-performance prediction. Particularly in shallow waters, a crucial contribution to the total transmission loss is the bottom refection loss, which can be estimated passively by beamforming the natural surface-noise acoustic field recorded by a vertical line array of hydrophones. However, the performance in this task of arrays below 2 m of length is problematic for frequencies below 10 kHz" role="presentation" style="display: inline; line-height: normal; word-spacing: normal; word-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; max-height: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px 2px 0px …

Sound Data Collection And Transmission Noise Reduction, Bradley Cockrel

Mahurin Honors College Capstone Experience/Thesis Projects

The WKU Engineering Department Senior Student Team, The Synchronizers, has been contracted to modify a MTD transmission’s sound characteristics. This project entails developing a sound data acquisition apparatus and method, developing a sound test stand which will fully load the transmission and load characteristics, and suggesting modes of sound modification. The Sound Data Acquisition method entails using a specialized microphone calibrated to operate on IOS devices to measure Sound Intensity. The sound intensity will be found over a collective area, in order to evaluate to the sound power generated. The sound test stand will consist of a system designed to …

The Effect Of Honeycomb Cavity: Acoustic Performance Of A Double-Leaf Micro Perforated Panel, Yuxian Huang, Kai Ming Li

The Summer Undergraduate Research Fellowship (SURF) Symposium

A micro perforated panel (MPP) is a device consisting of a thin plate and submillimeter perforations for reducing low frequency noise. MPPs have many advantages compared to traditional sound absorption materials, such as durability and designability, and they can be used in a variety of places such as room interior designs, passenger and crew compartments of aircrafts and combustion engines. The models in this study were designed and fabricated with the latest 3-D printing technology. The transmission loss and sound absorption coefficient of the 3-D printed double-leaf MPPs with honeycomb cavities were studied. According to the established theory, MPPs work …

Dynamic Behavior Of A Clamped-Clamped Bi-Stable Laminate For Energy Harvesting, Ajay V. Kumar, Andres F. Arrieta Ph.D., Myungwon Hwang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Multi-stable laminates have many applications in morphing structures, energy harvesting devices, and metamaterials due to the specific characteristics attributed to the exhibited stable states. Changes between stable states allow for large deflections, on-demand variation of the stiffness of compliant structures embedded within these elements, and control of effective dynamic properties in periodic lattices. These changes in state can be accessed via a snap-through instability triggered by introducing a well-defined activation energy. The resulting oscillations could enable broadband energy harvesting via piezoelectric transduction and resistive circuits. In this paper, a clamped-clamped bi-stable laminate is studied to understand the behavior of the …

Development Of Data Analytics Tools For Acoustic Measurement Of Positive Displacement Machines, Dan Ding, Monika Ivantysynova, Paul Kalbfleisch

The Summer Undergraduate Research Fellowship (SURF) Symposium

Noise control is an important factor in evaluating the design of positive displacement machines. This research project aims to develop new tools in MATLAB, with emphasis on visual approaches, to comprehensively characterize the noise generated by positive displacement machines in spatial, temporal and frequency domains. Sound pressure level (SPL), sound intensity level (SIL) and loudness were calculated and plotted on a measurement surface surrounding the pump, which illustrates the spatial distribution of the sound field. In order to highlight the phenomenon within specific frequency bands, Butterworth filters were used to isolate desired frequencies, such that specific harmonic content or 1/3 …

The Influence Of Thermal Conditions On The Thermomechanics Of Particulate-Composite, Mock Explosive Samples Under Near-Resonant Excitation, Jaylon B. Tucker, Allison R. Range, Jeffrey F. Rhoads

The Summer Undergraduate Research Fellowship (SURF) Symposium

Vapor detection is one of the most effective ways to find hidden plastic-bonded explosives in the field today. In recent years, it has been demonstrated that providing near-resonant vibratory excitation to explosives dramatically increases their vapor pressure, allowing for easier detection. Unfortunately, there currently exists a limited understanding of the thermomechanics of energetic material. This study seeks to help fill this technical void by exploring the thermomechanics of mock plastic-bonded explosives using direct mechanical excitation with varying thermal conditions. Using two different ambient thermal boundary conditions (insulated geometric boundaries and boundaries with free convection), a 7" by 10" by 0.5" …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.

Efficient Modeling Of Sound Source Radiation In Free-Space And Room Environments, Yangfan Liu

Open Access Dissertations

Motivated by the need to develop efficient acoustics simulations for sources in different room environments, a modeling procedure has been proposed that consists of two steps in general: (1) the modeling of the free-space radiation of the source based on measurements in a anechoic environment, and (2) the prediction of the sound field in a room environment based on that free-space information.

To achieve a high modeling efficiency, i.e., to reduce the number of modeling parameters while still maintaining acceptable accuracy, a Multipole Equivalent Source Model (ESM) with undetermined source locations has been developed for the free-space sound field prediction. …

Implementing And Testing A Panel-Based Method For Modeling Acoustic Scattering From Cfd Input, S. Hales Swift

Open Access Dissertations

Exposure of sailors to high levels of noise in the aircraft carrier deck environment is a problem that has serious human and economic consequences. A variety of approaches to quieting exhausting jets from high-performance aircraft are undergoing development. However, testing of noise abatement solutions at full-scale may be prohibitively costly when many possible nozzle treatments are under consideration. A relatively efficient and accurate means of predicting the noise levels resulting from engine-quieting technologies at personnel locations is needed. This is complicated by the need to model both the direct and the scattered sound field in order to determine the resultant …

Development Of The Compact Jet Engine Simulator From Concept To Useful Test Rig, Henry H. Haskin

Mechanical & Aerospace Engineering Theses & Dissertations

Two Compact Jet Engine Simulator (CJES) units were designed for integrated wind tunnel acoustic experiments involving a Hybrid Wing Body (HWB) vehicle. To meet the 5.8% scale of the HWB model, Ultra Compact Combustor technology from the Air Force Research Laboratory was used. The CJES units were built and integrated with a control system in the NASA Langley Low Speed Aero acoustic Wind Tunnel. The combustor liners, plug—vane and flow conditioner components were built in-house at Langley Research Center. The operation of the CJES units was mapped and fixes found for combustor instability tones and rig flow noise. The original …

Magnetic Bearing For Bently Nevada Rk4 Rotor Kits, Sean Fowler, Garrett Olson

Mechanical Engineering

Active Magnetic Bearings (AMB) are contact free bearings that support loads by magnetic levitation. This is accomplished by generating magnetic forces with electric current through a series of electromagnets surrounding a suspended rotor mass. Along with a set of electromagnets, an AMB assembly also consists of power amplifiers for each electromagnet, a controller, and proximity sensors. The proximity sensors provide rotor position feedback to the control system, which modulates power to the amplifiers [4]. Magnetic bearings are used in several industrial applications today, including but not limited to compressors, turbines, pumps, motors, and generators. Advantages of their utility include very …

Low Cost Metal Chip Separator, Alek Linquist, Kale Mckinney, Ryan Jones

Mechanical Engineering

We were tasked by Micro-Vu to design, build, and test a small-scale low-cost metal chip separator to operate on one of their 24/7 mills. The goal of the project was to separate the steel and aluminum chips coming off of the mill’s chip conveyor to end up with a bin of 99% pure aluminum by mass. To accomplish this goal we first brainstormed various possible ideas and performed small scale tests the best ones. After further review we determined the best solution to this problem was a design that involved a cycling magnetic backing that would pull steel out of …

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Physical Testing Of Potential Football Helmet Design Enhancements, Michael Jeremy Schuster

Master's Theses

Football is a much loved sport in the United States. Unfortunately, it is also hard on the players and puts them at very high risk of concussion. To combat this an inventor in Santa Barbara brought a new design to Cal Poly to be tested.

The design was tested in small scale first in order to make some preliminary conclusions about the design. In order to fully test the helmet design; however, full scale testing was required. In order to carry out this testing a drop tower was built based on National Operating Committee on Standards for Athletic Equipment, NOCSAE, …

Time-Of-Flight Based Sonic Speed Measurements For Cold Gas Thruster Development, Brandon W. Kempf

Mechanical Engineering Undergraduate Honors Theses

The purpose of this thesis is to explore an experiment developed for validating the usage of a gaseous solution of water and propylene glycol for cold gas propulsion. The experiment involves a “Time of Flight” method of calculating the speed of sound in the gas and the corresponding specific heat ratio using a copper tube, two MEMS microphones, a piezoelectric speaker, and data-acquisition hardware. The experiment was calibrated using the known thermodynamic properties of air. The accuracy of the experiment was found to be within 0.6% for calculations of the speed of sound in air and within 1.0% of the …

Effects Of Noise, Reverberation And Foreign Accent On Native And Non-Native Listeners’ Performance Of English Speech Comprehension, Zhao Ellen Peng, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

A large number of non-native English speakers may be found in American classrooms, both as listeners and talkers. Little is known about how this population comprehends speech in realistic adverse acoustical conditions. A study was conducted to investigate the effects of background noise level (BNL), reverberation time (RT), and talker foreign accent on native and non-native listeners' speech comprehension, while controlling for English language abilities. A total of 115 adult listeners completed comprehension tasks under 15 acoustic conditions: three BNLs (RC-30, RC-40, and RC-50) and five RTs (from 0.4 to 1.2 s). Fifty-six listeners were tested with speech from native …

Design And Optimization Of Membrane-Type Acoustic Metamaterials, Matthew G. Blevins

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

One of the most common problems in noise control is the attenuation of low frequency noise. Typical solutions require barriers with high density and/or thickness. Membrane-type acoustic metamaterials are a novel type of engineered material capable of high low-frequency transmission loss despite their small thickness and light weight. These materials are ideally suited to applications with strict size and weight limitations such as aircraft, automobiles, and buildings. The transmission loss profile can be manipulated by changing the micro-level substructure, stacking multiple unit cells, or by creating multi-celled arrays. To date, analysis has focused primarily on experimental studies in plane-wave tubes …

On The Scattering Of An Acoustic Plane Wave By A Soft Prolate Spheroid, Joseph Michael Borromeo

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis solves the scattering problem in which an acoustic plane wave of propagation number K1 is scattered by a soft prolate spheroid. The interior field of the scatterer is characterized by a propagation number K2, while the field radiated by the scatterer is characterized by the propagation number K3. The three fields and their normal derivatives satisfy boundary conditions at the surface of the scatterer. These boundary conditions involve six complex parameters depending on the propagation numbers. The scattered wave also satisfies the Sommerfeld radiation condition at infinity. Through analytical methods, series representations are constructed for the interior field …

The Effects Of Ball Interactions On The Dynamic Behavior Of A Ball Balancer Rotating At Speeds Above The Translational Resonant Frequency Of The System., Gregory A. Dedow

Electronic Theses and Dissertations

Many applications are inherently rotational in nature. These applications range from industrial products to consumer products. As seen in a traditional frequency response plot, the motion of a rotating imbalance does not approach zero as the forcing frequency is increased. Unlike a traditional forced mass spring oscillator, the motion of the rotating imbalance approaches some non-zero value. To account for this residual motion, some systems utilize a balancing device to reduce this motion. These balancing devices can be passive or active, depending on the design considerations. This paper will focus on the traditional, passive ball-type balancer due to its simplicity …

Preliminary Design Tools In Turbomachinery: Non-Uniformly Spaced Blade Rows, Multistage Interaction, Unsteady Radial Waves, And Propeller Horizontal-Axis Turbine Optimization, Yujun Leng

Open Access Dissertations

Turbomachinery flow fields are inherently unsteady and complex which makes the related CFD analyses computationally intensive. Physically based preliminary design tools are desirable for parametric studies early in the design stage, and to provide deep physical insight and a good starting point for the later CFD analyses. Four analytical/semi-analytical models are developed in this study: 1) a generalized flat plate cascade model for investigating the unsteady aerodynamics of a blade row with non-uniformly spaced blades; 2) a multistage interaction model for investigating rotor-stator interactions; 3) an analytical solution for quantifying the impeller wake convection and pressure wave propagating between a …