Acoustics, Dynamics, and Controls Commons^™

Pseudodifferential Absorbing Boundary Conditions For Waves, Lauren Taylor

Mechanical Engineering Theses

Absorbing boundary conditions (ABCs) are required to truncate the computational domain when performing Finite Element Analyses of exterior acoustic problems where physical domain is unbounded. ABC is applied on a fictitious boundary containing the scatterer and ideally allows outgoing waves to leave without non-physical reflections. Preventing artificial reflections is essential to benefit from the accuracy of the numerical method used. Otherwise, ABC acts as a reflective surface, and artificial reflections distort the solution in the entire domain which is not recoverable by any type of refinement. Pseudodifferential ABCs were used to describe the Dirichlet-to-Neumann map which maps known boundary values …

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Design And Implementation Of An Optimization Platform For Common Fixed Photovoltaic Systems, Amro Ahmad Zahrawi

Mechanical Engineering Theses

Most household photovoltaic (PV) panels are installed in a fixed arrangement (fixed-type) based on a rule of thumb that comes from experience. The azimuth angle is usually set facing south with a tilt angle equivalent to the location's latitude. However, research shows that this is not the best for all geographical locations and during all hours of the day. Consequently, this brings up the hypothesis that optimizing the PV system's azimuth and tilt angles would ensure that the PV panel produces the most possible output as it is adjusted to face the sun most effectively during peak sunlight hours. This …

Experimental And Theoretical Analysis Of Nonlinear Triboelectric Energy Harvester For Frequency Up-Conversion Applications, Hadeel A. Abumarar

Mechanical Engineering Theses

With the development of micro-sensors and wireless applications, energy harvesting has become an effective method for self-powering. However, ambient energy is only limited to below 100Hz, which restricts the energy harvester designs to this range resulting in
an impractical bulky and large-scale harvester. Therefore, in this thesis, we investigated
frequency Up and Down conversion energy harvesters to benefit from the high-frequency oscillations and transferred them to the ambient vibration ranges. Toward this, the triboelectric transduction mechanism has been utilized for a frequency-up conversion for energy harvesting applications, while the piezoelectric transduction mechanism is used for frequency-down
conversion for mass sensing …

Experimental And Theoretical Investigation Of Vibro-Impact Triboelectric Energy Harvesters, Mostafa Hassan

Mechanical Engineering Theses

Improving the efficiency of energy harvesting, by investigating different techniques to increase the harvester bandwidth, as well as by exploring the influencing factors and adjusting them to optimal setups. Towards this, multiple Vibro-impact energy harvesters were proposed in this study. First, a Two-Degree of Freedom (2DOF) Vibro-impact Triboelectric Energy Harvester with a single and a double impact configuration is proposed. Multi-modality and piecewise linearity were combined to improve the harvesting bandwidth of triboelectric energy harvesters utilizing two resonant frequencies. The harvester structure consists of a primary cantilever beam attached to a secondary cantilever beam through a tip mass in the …

Simultaneous Thermal Zoning And Demand Control Ventilation, Jose Rodriguez

Mechanical Engineering Theses

Heating Ventilation and Air Conditioning (HVAC) systems include the equipment used to control the conditions and distribution of indoor air in any closed environment that requires certain variables, such as temperature, humidity, carbon dioxide (CO₂) concentration, etc. to be controlled to levels of human comfort and safety, and to levels that keep machines and other devices in special conditions to protect them or guarantee their best performance. In developed countries, HVAC energy consumption is usually between 25% and 42% of the total energy consumption. Thermal zooning and demand control ventilation have shown improvements in comfort and energy consumption savings. The …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …