Mechanical Engineering Commons^™

Impact Of Extended Sintering Times On Mechanical Properties In Pa-12 Parts Produced By Powderbed Fusion Processes, Garrett Craft, Justin Nussbaum, Nathan B. Crane, J. P. Harmon

Faculty Publications

Additive Manufacturing provides many advantages in reduced lead times and increased geometric freedom compared to traditional manufacturing methods, but material properties are often reduced. This paper considers powder bed fusion of polyamide 12 (PA12, Nylon 12) produced by three different processes: laser sintering (LS), multijet fusion (MJF)/high speed sintering (HSS), and large area projection sintering (LAPS). While all utilize similar PA12 materials, they are found to differ significantly in mechanical properties especially in elongation to break. The slower heating methods (MJF/HSS and LAPS) produce large elongation at break with the LAPS process showing 10x elongation and MJF/HSS exhibiting 2.5x the …

Tooling For Injection Molding Using Laser-Powder Bed Fusion., Mohith Ram Buxani

Electronic Theses and Dissertations

Laser-Powder Bed Fusion (L-PBF) has been considered for some time by the injection molding industry for the fabrication of tooling for injection molding in order to address large lead times and costs for tool-making. Computer-aided simulations are also routinely used to evaluate new part and mold designs as well as understanding the effects of material compositions and processing conditions on part quality and overall productivity. However, there remains a significant need to integrate the perspectives from injection molding, 3D printing, metal powders, and component design and process simulation to better utilize LPBF for fabricating tooling required for injection molding. The …

Solid Oxide Electrochemical Cells For High Temperature Hydrogen Production: Theory, Fabrication And Characterization, Can Zhou

Mechanical & Aerospace Engineering Theses & Dissertations

In this dissertation, the concept of water splitting using solid oxide photoelectrochemical cells (SOPCs) at high temperature was introduced and experimentally investigated. High temperature photoelectrochemical water splitting physically broadens the selection of potential applicable semiconductor materials and enables more visible sunlight absorption. This newly conceived concept provides a unique pathway for solar hydrogen production, as compared to conventional photoelectrochemical cells (PECs) that use wide band gap semiconductors in aqueous environments. The theoretical framework of SOPC was elaborated, followed by the experimental investigation to search for appropriate high temperature materials. Selected high temperature Schottky and p-n junction diodes, which were expected …

Evaluation Of Processing Variables In Polymer Projection Sintering, Justin Nussbaum, Nathan B. Crane

Faculty Publications

Purpose – Projection sintering, a system for selectively sintering large areas of polymer powder simultaneously with a high power projector is introduced. The paper evaluates the suitability of laser sintering process parameters for projection sintering as it uses substantially lower intensities, longer exposure times, and larger areas than conventional laser sintering (LS).

Design/methodology/approach – The tradeoffs in sintering outcomes are evaluated by creating single layer components with varied exposure times and optical intensities. Some of these components were cross-sectioned and evaluated for degree of densification while the single layer thickness and the maximum tensile force was measured for the rest. …

Investigation Of Thermal History In Large Area Projection Sintering, An Additive Manufacturing Technology, Justin Nussbaum

USF Tampa Graduate Theses and Dissertations

The goal of this work is to explore the benefits of using long exposure times with polymer powder bed fusion additive manufacturing processes and examine the feasibly of this new application as a manufacturing process. It is well known that the sintering which occurs in these systems are a time and temperature dependent process. However, the most common powder bed fusion systems use a laser which scans and heats the powdered feedstock for microseconds at a time, leaving insufficient time for the polymer to fully melt and/or fuse, leading to reduced mechanical properties. Little has been published on the effects …

On The Development And Integration Of Pneumatic Extrusion Module And A Methodology To Identify Process Parameters For Additive Manufacturing Using Machine Learning, Kashish Dhal

Mechanical and Aerospace Engineering Theses - Archive

Commonly used additive manufacturing platforms have a single extrusion module based on Fused Filament Fabrication (FFF) and their processing software generates G-Codes for this FFF module using defined process parameters. These platforms and software do not accommodate different processing modules such as viscous extruders or Direct Ink Writing (DIW). This research is focused on the development of a Pneumatic Extrusion Module (PEM) capable of dispensing viscous materials such as gels or slurries controlled through a digital pneumatic valve. A PEM is developed, integrated and its performance is evaluated on a multi-modality additive manufacturing platform in the MARS Lab. The operation …

Predicting Mechanical Behavior Of 3d Printed Structures Using Mechanics Of Composites And Fracture, Megha Tangri

Mechanical and Aerospace Engineering Theses - Archive

Recently, additive manufacturing, or 3D printing as it is more commonly called, has taken a big leap in the manufacturing industry. This technology is rapidly moving from prototyping to manufacturing using metals, polymers, concrete and even composites. Unlike subtractive methods of manufacturing, additive manufacturing can be used to manufacture parts with highly directional mechanical properties. This research focuses on predicting tensile failure of 3D printed polymer structures in different raster orientations using composites lamination theory. Previously it was found experimentally that tensile strengths of 3D printed specimens decrease when raster orientations changes from 0° to 90°. The proposed model developed …

Peridynamic Modeling Of Dynamic Fracture In Bio-Inspired Structures For High Velocity Impacts, Sneha Akula

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Bio-inspired damage resistant models have distinct patterns like brick-mortar, Voronoi, helicoidal etc., which show exceptional damage mitigation against high-velocity impacts. These unique patterns increase damage resistance (in some cases up to 3000 times more than the constituent materials) by effectively dispersing the stress waves produced by the impact. Ability to mimic these structures on a larger scale can be ground-breaking and could be used in numerous applications. Advancements in 3D printing have now made possible fabrication of these patterns with ease and at a low cost. Research on dynamic fracture in bio-inspired structures is very limited but it is …

Understanding The Thermal Properties Of Precursor-Ionomers To Optimize Fabrication Processes For Ionic Polymer-Metal Composites (Ipmcs), Sarah Trabia, Kisuk Choi, Zakai Olsen, Taeseon Hwang, Jae-Do Nam, Kwang J. Kim

Mechanical Engineering Faculty Research

Ionic polymer-metal composites (IPMCs) are one of many smart materials and have ionomer bases with a noble metal plated on the surface. The ionomer is usually Nafion, but recently Aquivion has been shown to be a promising alternative. Ionomers are available in the form of precursor pellets. This is an un-activated form that is able to melt, unlike the activated form. However, there is little study on the thermal characteristics of these precursor ionomers. This lack of knowledge causes issues when trying to fabricate ionomer shapes using methods such as extrusion, hot-pressing, and more recently, injection molding and 3D printing. …

Modeling Residual Stress Development In Hybrid Processing By Additive Manufacturing And Laser Shock Peening, Guru Charan Reddy Madireddy

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The term “hybrid” has been widely applied to many areas of manufacturing. Naturally, that term has found a home in additive manufacturing as well. Hybrid additive manufacturing or hybrid-AM has been used to describe multi-material printing, combined machines (e.g., deposition printing and milling machine center), and combined processes (e.g., printing and interlayer laser re-melting). The capabilities afforded by hybrid-AM are rewriting the design rules for materials and adding a new dimension in the design for additive manufacturing paradigm. This work focuses on hybrid-AM processes, which are defined as the use of additive manufacturing (AM) with one …

Consuming Digital Debris In The Plasticene, Stephen R. Parks

Theses and Dissertations

Claims of customization and control by socio-technical industries are altering the role of consumer and producer. These narratives are often misleading attempts to engage consumers with new forms of technology. By addressing capitalist intent, material, and the reproduction limits of 3-D printed objects’, I observe the aspirational promise of becoming a producer of my own belongings through new networks of production. I am interested in gaining a better understanding of the data consumed that perpetuates hyper-consumptive tendencies for new technological apparatuses. My role as a designer focuses on the resolution of not only the surface of the object through 3-D …

3d Printed Pcu/Uhmwpe Polymeric Blends For Artificial Knee Meniscus, Raissa Araujo Borges

Graduate Theses and Dissertations

3D printing was used to fabricate porous artificial knee meniscus material from biocompatible polymeric blends of polycarbonate-urethane (PCU) and ultra-high-molecular-weight polyethylene (UHMWPE) to enable “weep” lubrication that mimics the native meniscus. 3D printed and molded pure PCU, as well as molded PCU and UHMWPE, were used for comparison. Preliminary printing was done to evaluate the impact of process parameters on the results. The samples were subject to a variety of rotational oscillating friction and wear tests under simulated body fluid and loading conditions to replicate the natural motion of the knee. Results show that 3D printed PCU samples yielded a …

Fused Filament Fabrication 3d Printing Using Low-Melting Alloys., Nirupama Warrier

Electronic Theses and Dissertations

Fused Filament Fabrication (FFF) 3D printing technology has been a popular method of creating prototypes using plastics in the timeliest and most affordable manner for electronic, automotive, and biomedical applications. 3D printing of metals and alloys using FFF technology could provide low-cost alternatives and solutions to the Laser-Powder Bed Fusion Process (L-PBF) and Binder Jetting processes (BJ). In current work, low melting alloys have been used as a starting material and evaluated for FFF 3D printing using two methodologies. In the first methodology, Sn60Bi40 alloy in the form of wire was used as the feedstock for FFF extrusion and process …

Note On The Rate And Energy Efficiency Limits For Additive Manufacturing, Timothy Gutowski, Sheng Jiang, Daniel Cooper, Gero Corman, Michael Hausmann, Jan-Anders Manson, Timo Schudeleit, Konrad Wegener, Matias Sabelle, Jorge Ramos-Grez, Dusan P. Sekulic

Mechanical Engineering Faculty Publications

We review the process rates and energy intensities of various additive processing technologies and focus on recent progress in improving these metrics for laser powder bed fusion processing of metals, and filament and pellet extrusion processing of polymers and composites. Over the last decade, observed progress in raw build rates has been quite substantial, with laser metal processes improving by about 1 order of magnitude, and polymer extrusion processes by more than 2 orders of magnitude. We develop simple heat transfer models that explain these improvements, point to other possible strategies for improvement, and highlight rate limits. We observe a …

Impact Of Diy Home Manufacturing With 3d Printing On The Toy And Game Market, Emily Peterson, Joshua M. Pearce

Department of Materials Science and Engineering Publications

The 2020 toy and game market is projected to be US$135 billion. To determine if 3D printing could affect these markets if consumers offset purchases by 3D printing free designs, this study investigates the 100 most popular downloaded designs at MyMiniFactory in a month. Savings are quantified for using a Lulzbot Mini 3D printer and three filament types: commercial filament, pellet-extruded filament, and post-consumer waste converted to filament with a recyclebot. Case studies probed the quality of: (1) six common complex toys; (2) Lego blocks; and (3) the customizability of open source board games. All filaments analyzed saved the user …

Open Source Multi-Head 3d Printer For Polymer-Metal Composite Component Manufacturing, J. Laureto, Joshua M. Pearce

Department of Materials Science and Engineering Publications

As low-cost desktop 3D printing is now dominated by free and open source self-replicating rapid prototype (RepRap) derivatives, there is an intense interest in extending the scope of potential applications to manufacturing. This study describes a manufacturing technology that enables a constrained set of polymer-metal composite components. This paper provides (1) free and open source hardware and (2) software for printing systems that achieves metal wire embedment into a polymer matrix 3D-printed part via a novel weaving and wrapping method using (3) OpenSCAD and parametric coding for customized g-code commands. Composite parts are evaluated from the technical viability of manufacturing …

The Intersection Of Manufacturing Technologies And School Music Programs, Leslie Prunier

University Scholar Projects

The objective of this project is to design and manufacture a musical instrument, a marching baritone horn, out of plastic. It is constructed out of both PVC pipe and 3D-printed components. Utilizing this project’s documentation, a high school student could use a 3D printer and other basic tools to make their own musical instrument for a fraction of the cost of purchasing one. This documentation will produce a horn tuned in the key of B flat with one functioning valve, and suggestions for future work to make the other two valves functional as well.

Manufacturing And Characterization Of A 3d-Printable, Antibacterial, Magnesium Oxide Nanoparticles Reinforced Abs Filament, Saket Thapliyal

Mechanical and Aerospace Engineering Theses - Archive

This research work consists of two phases. In phase one it is intended to manufacture an antibacterial 3D printable filament by extruding a solid state mixture of (MgO) nanoparticles (NPs) and Acrylonitrile Butadiene Styrene (ABS) pellets. A single screw extruder was used to extrude ABS pellets containing 0, 0.5, 1, 2 and 4 wt. % MgO NP. This phase deals with manufacturing and testing the filament for mechanical properties, antibacterial properties and 3D printability. On one hand tensile strength, ductility and 3D-printabiliy were observed to decrease with increasing concentrations of MgO NP in ABS matrix, on the other hand the …

Bio Inspired Lightweight Composite Material Design For 3d Printing, Kaushik Thiyagarajan

Electronic Theses and Dissertations

Lightweight material design is an indispensable subject in product design. The lightweight material design has high strength to weight ratio which becomes a huge attraction and an area of exploration for the researchers as its application is wide and increasing even in every day-to-day product. Lightweight composite material design is achieved by selection of the cellular structure and its optimization. Cellular structure is used as it has wide multifunctional properties in addition to the lightweight characteristics. Applications of light weight cellular structures are wide and is witnessed in all industries from aerospace to automotive, construction to product design. In this …

Design And Implementation Of An Air Multiplier Fan For Pc, George Demian

Williams Honors College, Honors Research Projects

Mechanical engineering student (B.S.) senior design project. Conception, design (SolidWorks), 3D printing & processing, testing of a scaled down air multiplier "bladeless" fan within a computer chassis as a cooling solution.

Effect Of Manufacturing-Induced Defects And Orientation On The Failure And Fracture Mechanism Of 3d Printed Structures, Amit Khatri

Mechanical and Aerospace Engineering Theses - Archive

Additive manufacturing is a rapidly growing cutting edge technology. Number of experimental studies have shown that strength of product manufactured by additive Fused Deposition Method (FDM) is influenced by different processing parameters involved during manufacturing. This thesis work presents experimental and theoretical investigation of mechanical behavior of ABS material fabricated with variation in some of process parameters such as Axis Orientations, Raster Orientation, Infill Percentage, Layer Height and Number of Shells. Different experiments were designed to understand the basics of 3D printing manufacturing and to characterize the mechanical behavior of 3D printed structures. This study helps to understand, how different …

Size Scaling Of Strength And Toughness For 3d Printed Polymer Specimens, Darren Thomas Bell

Open Access Theses

To find material systems that offer low density and high strength, stiffness or toughness, hierarchically designed material systems have provided a promising research area. This thesis lays the groundwork for designing efficient micro-architectured material systems by characterizing size effects for 3d printed polymer parts. Two methods were used to analyze data from 3-point bend tests for specimens of varying size: the load-separation method was used for finding the point of crack growth initiation and Bazant’s method was used to find shape independent strength at failure. The strength values were used as inputs for finding size independent material constants within a …

Bioink Properties Before, During And After 3d Bioprinting, Katja Hölzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov

Department of Mechanical and Materials Engineering: Faculty Publications

Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Stiffness Reduction Strategies For Additively Manufactured Compliant Mechanisms, Ezekiel G. Merriam

Theses and Dissertations

This work develops and examines design strategies for reducing the stiffness of 3D-printed compliant mechanisms. The three aspects of a flexure that determine its stiffness are well known: material, boundary conditions, and geometry. In a highly constrained design space however, flexure stiffness may remain unacceptably high even while arriving at the limits of design constraints. In this work, changes to geometry and boundary conditions are examined that lead to drastically reduced stiffness behavior without changing flexure thickness, width, or length. Changes to geometry can result in very complex mechanisms. However, 3D printing enables almost arbitrarily complex geometries. This dissertation presents …

3d Heart Model For Mapping Rf Ablation Sites, Danielle Corsino, Ashleigh Mims, Andrew Potter, Alejandro Rivera

Capstone Design Expo Posters

Electro-Cardiologists routinely insert radiofrequency probes into the heart and conduct targeted ablation procedures to correct irregular heartbeats. Current techniques are very experience and “touch” based, and require the novice cardiologist about 50 procedures to become proficient. There is a need for a functional heart model device that can be used to reduce the amount of procedures on human patients before cardiologist become proficient. Project constraints included limited software availability for segmenting accuracy, available 3D printing technology and materials, and cost to 3D print heart models due to the complex geometry. The team began with a CT scan, ITK SNAP and …

3d Printed Teeth: Anatomically Correct Primary Replicas, Anh Nguyen, Stefan Harris

Capstone Design Expo Posters

The current method of molding teeth, especially primary teeth, cannot accurately reproduce internal tooth structures. Therefore, there is a need for primary teeth to be made anatomically accurate on-demand with the ability to customize a model for specific patients. This project aims that any tooth extracted digitally from a Dental Cone Beam computed tomography (CBCT) scan of a child's mouth can be 3D printed into an accurate replicate with which dental students can practice. Constraints include viable materials that can be printed by a 3D printer, represent tooth anatomy and provide desirable mechanical properties compatible with the dental drilling operation. …

A Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Asme Mini-Baja Rc Car (Steering And Suspension Systems), Michael E. Cox

All Undergraduate Projects

The issue that this project is concerned with is how to design and build a drivetrain, steering and suspension systems for an RC car. The systems must be simple and functional. Furthermore, these systems will be designed to fit on a small chassis and not interfere with each other. They also need to be strong and durable enough to propel the car forward and maneuver through various obstacles and be built in a way that is easy to take apart and repair quickly. These design problems were approached using basic mechanical design concepts such as gear kinematics, spur and bevel …

Bioink Properties Before, During And After 3d Bioprinting, Katja Holzl, Shengmao Lin, Liesbeth Tytgat, Sandra Van Vlierberghe, Linxia Gu, Aleksandr Ovsianikov

Department of Mechanical and Materials Engineering: Faculty Publications

Bioprinting is a process based on additive manufacturing from materials containing living cells. These materials, often referred to as bioink, are based on cytocompatible hydrogel precursor formulations, which gel in a manner compatible with different bioprinting approaches. The bioink properties before, during and after gelation are essential for its printability, comprising such features as achievable structural resolution, shape fidelity and cell survival. However, it is the final properties of the matured bioprinted tissue construct that are crucial for the end application. During tissue formation these properties are influenced by the amount of cells present in the construct, their proliferation, migration …