Mechanical Engineering Commons^™

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Rc Baja 2023 Drivetrain And Chassis, Nathan Norby

All Undergraduate Projects

Students’ objective this quarter was to design a remote-controlled vehicle that utilizes a 4-link rear suspension, an I-beam front suspension, the ability to withstand a substantial front impact and several gearing options. The team also used several agreed upon design requirements to quantify the results of the objective.

To meet these objectives students followed a strict engineering method. Students split into a team’s divided the work into two sections. Max was responsible for the suspension and steering and Nathan was responsible for the chassis and drivetrain. Methods included engineering analysis which used mechanics of materials, static analysis, dynamic analysis, and …

Balsa Wood Bridge, Daniel R. Netro

All Undergraduate Projects

When building a bridge, there is a lot of criteria that need to be met so it can be functional. These criteria for this balsa bridge competition are what the bridge is made out of and can only weigh so much, the bridge must hold a certain amount of weight and not fail due to it, must allow a “vehicle” to go through the bridge and under it. For this bridge, the only material that can be used is balsa wood and any glue. With this, the strength of the material can be found and multiple calculations can be used …

Jcati Carbon Fiber Recycler: Oven Heating System, Kezyah Mantanona

All Undergraduate Projects

Central Washington University Mechanical Engineering Technology students are working with the Joint Center for Aerospace Technology Innovation (JCATI) to create a device that recycles carbon fiber wing trimmings produced by the wing manufacturing process for the Boeing 777 airplanes. The solution to this problem was to utilize crushing, shredding, and pyrolysis to remove the resin from the composite material and provide carbon fiber that can be repurposed. This project focuses on both the Oven Enclosure which will house the Oven Heating System as well as the heating elements and control circuit that are responsible for allowing the material to reach …

Advanced Microstructural Characterization Of Functionally Graded Dental Ceramic Material For Materials-Informed Finishing, Angani Vigneswaran

Theses and Dissertations--Manufacturing Systems Engineering

Yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) has gained popularity as the choice of material for dental prosthetics. Ivoclar Vivadent’s IPS e.max ZirCAD Prime dental ceramic incorporates a unique gradient technology that varies the yttria content over the thickness of the material. The top layer is composed of 5Y-TZP which is desired for its optical properties while the bottom layer is composed of a much stronger 3Y-TZP. In between the two layers, 5Y-TZP and 3Y-TZP are mixed to form a transition layer. Varying the amount of yttria allows for more esthetically pleasing translucency in the visible areas of the restoration without compromising …

Radio-Controlled Baja Car, Jaxx Brown

All Undergraduate Projects

The Central Washington University RC Baja competition tests students’ skills in engineering in a matter of ability to design, construct and test an RC car. The objective of this senior project is to manufacture efficient suspension and steering systems for an RC vehicle and compete at the end of the school year against other students’ vehicles. Two races will be conducted during the competition, the RC vehicle will compete in a slalom-and-sprint and a Baja. Using more than one manufacturing method and material was expected of students to create the steering and suspension systems. Through CAD software and 3D printers …

Rc Baja Project: Suspension And Steering, Chance Hills

All Undergraduate Projects

Students designed and manufactured an RC Baja car to compete in the ASME RC Baja competition. The goal of this section of the project was to create a steering system and suspension system that work together properly with a partner’s chassis/drive train systems during tests and competitions. The car needed to be able to complete in the three events, which are a drag race, a solemn course, and the Baja event. The RC will also be evaluated on the ability to climb inclines, top speed, and withstand the drop test. This proposal will explain all the details and effort that …

Balsa Wood Bridge, Minh Le

All Undergraduate Projects

This senior paper outlined the design and construction of an articulating balsa wood bridge. Meeting specific criteria to hold 20kg of weight hanging from the center of the bridge. Also allowing a 32 mm wide by 25 mm high object to traverse the road deck of the bridge. The construction criteria required the use of only balsa wood and glue for the structural support, with exceptions for articulation components. The total weight of the bridge must not exceed 85 grams.

To achieve these goals, the bridge was designed using static equilibrium and material strength equations to span a 470mm body …

Gamelan Gong Directivity Dataset, Samuel D. Bellows, Dallin T. Harwood, Kent L. Gee, Micah R. Shepherd

Directivity

No abstract provided.

Zno Varistors – The Ideal Microstructure And Characteristics, And Methods Investigated And Developed To Achieve These, Maura Kelleher

Books/Book Chapters

ZnO-Bi2O3-Sb2O3 varistors have been extensively studied since their discovery 5 decades ago. Their function in protecting increasingly sensitive electronic components by absorbing random surges of energy is even more important today. Also, the metal oxides from which they are made from are becoming even more precious. Their electrical characteristics are highly dependent on their microstructural characteristics which are highly dependent on their composition and methods used. The purpose of this article is to explain the ideal microstructure required to obtain the ideal electrical characteristics, the powder preparation methods investigated and developed to achieve it, and some future directions are outlined.

Jcati Carbon Fiber Recycler: Gearing And Shredding, Diana Faamausili

All Undergraduate Projects

The purpose of this project is to build and improve on the carbon-fiber recycler at Central Washington University. The carbon-fiber recycler consists of four components such as a crusher, shredder, conveyor, and oven. This report will focus on the shredding and gearing elements. The chain drive on the shredder and the gearing module were replaced with a synchronous belt drive.

The pitch diameters for the sprockets on the shredder and the center distance of the shafts was evaluated to find the belt length. The velocity ratio and the angular velocity was used to find the minimum torque on the shaft. …

Rc Baja - Drivetrain And Chassis, James C. Cando

All Undergraduate Projects

The annual RC Baja competition which is held at Central Washington University during the third week of April, showcases the different remote-control vehicles built by the student teams and put the vehicles in series of different challenges such as the sprint, slalom, and motocross. The objective of the senior project is to design, manufacture, and test mainly a drivetrain system as well as a chassis. The drivetrain system provides power for the driving force and the chassis provides housing for the different components of the vehicle. The process began with setting requirements for the vehicle that was used to determine …

Self-Diffusion In Misoriented Aluminum (111) Substrates After Jump-To-Contact, Noah Kane Manuel

Mechanical Engineering Master's Theses

Self-diffusion between misoriented aluminum (111) substrates after jump-to-contact (JC) is studied using molecular dynamics simulations. Diffusive behaviors of three twist misorientation angles, 2.45°, 4.40° and 6.00°, are studied at temperatures ranging from 75% to 95% of the melting temperature of aluminum. The existence of the post-JC interface is found to enhance diffusive behavior of atoms near the interface. The 4.40° misorientation angle has the highest pre-exponential factor of diffusion and the lowest activation energy, when compared to the other angles. For all misorientations the activation energies in the direction perpendicular to the JC interface was found to be the lowest. …

Nebraska Tractor Test: 2266 John Deere 9rx 640, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary #1273: Case Ih Optum 340 Cvx, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Evaluating The Sustainability Of Paper And Plastic Substitute Material Limex, E.-Lexus Thornton, Avery Hartley, Daniel Caudill, Martin Gamesu, Julius M. Schoop, Fazleena Badurdeen

Mechanical Engineering Faculty Publications

With the increasing decline in the environment and natural resources it is important to find new ways in which manufacturing can increase the sustainability of the world. This study seeks to compare LimeX, a state-of-the-art paper and plastic alternative primarily made of limestone, with conventional paper and plastic materials. For a better understanding of LimeX as a material, a brief investigation of the mechanical and chemical properties will be performed through experimentation and analysis. In addition, this paper aims to evaluate the sustainability of LimeX through the analysis of metrics relating to the triple bottom line (environmental impacts, economic impacts …

Incorporation Of Poly(Tfema) In Perovskite Thin Films Using A Supercritical Fluid, Kasey Handy, Gary C. Tepper

Mechanical and Nuclear Engineering Publications

A new process is reported for the incorporation of a fluoropolymer into a solid perovskite film. Poly(trifluoroethyl methacrylate) [CH₂C(CH₃)(CO₂CH₂CF₃)]_n was delivered to methylammonium lead iodide (CH₃NH₃PbI₃) perovskite films by crystallizing the film in supercritical carbon dioxide/ethanol containing the dissolved fluoropolymer. The surface was characterized before and after fluoropolymer exposure using scanning electron microscopy, Raman spectroscopy, and contact angle measurements. The results indicate that the fluoropolymer was incorporated into the perovskite film during the supercritical fluid crystallization process. The incorporation of a hydrophobic fluoropolymer …

Effects Of Exciting And Relaxing Music On Heart Rate Variability, Pratik S. Mahajan

Honors Undergraduate Theses

Heart rate variability (HRV) and music have been demonstrated to have a relationship in previous literature. The primary objective of this study is to further investigate that relationship by observing HRV during periods of listening to relaxing and exciting music and comparing the results to a baseline as well as the other condition. The secondary objective of this study is to investigate the efficacy and potential usage of the Polar H10 chest strap monitor in measuring HRV parameters. The results of the Polar H10 will be compared to the iWorx TA-220 and iWorx-ECG12, the existing gold standard in HRV and …

Concentration Field Based Micropore Flow Rate Measurements, Matia P. Edwards, Samuel F. D. J. Gómez, Michael S. H. Boutilier

Chemical and Biochemical Engineering Publications

Demand is growing for a larger catalogue of experimental techniques to measure flow rates through micro-/nanoscale systems for both fundamental research and device development. Flow emerging from a hole in a plane wall is a common system of interest in such work for its relevance to membrane separation. In this paper, we consider the possibility of measuring volume flow rates through small scale orifice plates from images of dye dispersions downstream. Based on approximate analytical solutions to the advection–diffusion equation, we show that, at low Reynolds numbers, the concentration in the nearly hemispherical plume that forms increases linearly with inverse …

An Efficient And Low-Cost Method To Create High-Density Nitrogen-Vacancy Centers In Cvd Diamond For Sensing Applications., Prem Bahadur Karki, Rupak Timalsina, Mohammadjavad Dowran, Ayodimeji E. Aregbesola, Abdelghani Laraoui, Kapildeb Ambal

Department of Mechanical and Materials Engineering: Faculty Publications

The negatively charged Nitrogen-Vacancy (NV^-) center in diamond is one of the most versatile and robust quantum sensors suitable for quantum technologies, including magnetic field and temperature sensors. For precision sensing applications, densely packed NV^- centers within a small volume are preferable due to benefiting from 1/√𝑁 sensitivity enhancement (N is the number of sensing NV centers) and efficient excitation of NV centers. However, methods for quickly and efficiently forming high concentrations of NV^- centers are in development stage. We report an efficient, low-cost method for creating high-density NV^- centers production from a relatively …

Correction: Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2o3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Rupak Timalsina, Christian H. Binek, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Correction for ‘Nanoscale imaging of antiferromagnetic domains in epitaxial films of Cr2O3 via scanning diamond magnetic probe microscopy’ by Adam Erickson et al., RSC Adv., 2023, 13, 178–185, https:// doi.org/10.1039/D2RA06440E

Traversing With Quantitative Fidelity Through The Glass Transition Of Amorphous Polymers: Modeling The Thermodynamic Dilatational Flow Of Polycarbonate, Mehrdad Negahban, Wenlong Li, Jean-Marc Saiter, Laurent Delbreilh, Kyle Strabala, Zheng Li

Department of Mechanical and Materials Engineering: Faculty Publications

We follow the assumption that the dilatational response of glassy polymers can be characterized by a back-stress type analog that includes a thermal expansion for each elastic component, and with a viscosity that is dependent on the expansion of the elastic back stress component. To this, we add the assumption of an unloaded equilibrium temperature that correlates to the past processing through the viscous flow. After setting this in a thermodynamically consistent structure, the elastic, elastic backstress, thermal expansion, back-stress thermal expansion, heat capacity and viscous damping are evaluated using existing experiments for the response of polycarbonate over the glassy …

Evaluation And Optimization Of Thermal Solutions In Air And Liquid Cooling Systems For Datacenters, Vibin Shalom Simon

Mechanical and Aerospace Engineering Dissertations - Archive

A data center is a specifically constructed establishment designed to accommodate computing, storage, and transmission equipment, thereby facilitating essential business operations spanning diverse sectors of the economy. This facility serves as the designated physical infrastructure for housing servers, networking components, and data storage systems. In the context of traditional data centers, a substantial portion of energy, specifically around 45% to 55%, is directed towards supporting information technology (IT) operations. Additionally, a considerable allocation, varying from 30% to 40%, is attributed to the facilitation of cooling processes. The scope of this dissertation study comprises nine distinct chapters, each contributing to addressing …

Non-Intrusive Reduced Order Model Formulation For Inverse Shape Design Including Deforming Meshes And Multiphysics Problems., Kapil Aryal

Mechanical and Aerospace Engineering Dissertations - Archive

Despite significant advancements in computer capabilities for numerical simulations, engineers continue to face limitations when dealing with large-scale full-order model(FOM) simulations. These simulations often necessitate repeated solves, such as those encountered in inverse design, real-time solution prediction, error quantification, and solver convergence, among others. To address these challenges, reduced order modeling (ROM) has emerged as a valuable approach. This thesis focuses on the development of an ROM framework that combines Proper Orthogonal Decomposition (POD) with machine learning techniques. This integrated approach is applied to a diverse range of heat transfer and fluid flow inverse design problems. POD constructs optimal sets …

Cooperative Manipulation And Formation Control Using Multiple Aerial Vehicles, Uluhan Cem Kaya

Mechanical and Aerospace Engineering Dissertations - Archive

Recent advancements in autonomous systems have significantly impacted both academia and industry, opening new research avenues. One of them is the collaboration of multiple systems to achieve a common goal, which is known as a cooperative system. In the lack of human intelligence, decision making and perception capabilities, uncrewed autonomous systems could mutually benefit from each other’s capabilities when they are deployed and utilized together. This research tackles the collaboration of group of uncrewed aerial systems (UASs) where the constraint on individual vehicles requires a varying level of coordination and cooperation. Such cooperation can be in the form of a …

Turbulent Shockwave/Boundary-Layer Interactions Generated By Sharp Swept Fins, Dustin Levi Otten

Mechanical and Aerospace Engineering Dissertations - Archive

The shock/turbulent boundary layer interaction (STBLI) generated by a sharp fin with a 60 deg leading edge sweep mounted above a flat plate at Mach 2.5 was studied numerically. Incipient separation due to this highly swept fin was determined by varying the fin angle to the incoming freestream. The effect of a small fin/plate gap on STBLI incipient separation was established. Sweeping the fin increases the deflection required for incipient separation as the sweep reduces the interaction strength. A gap causes flow leakage under the fin, further reducing the interaction strength on the windward side. The incipient angle of attack …

Experimental Study On Thermal Performance Of Metal Foam Heat Sinks In Single Phase Liquid Immersion Cooling, Manish Kumawat

Mechanical and Aerospace Engineering Theses - Archive

In 1965, Intel co-founder Gordon Moore made the observation that the transistor counts on a chip double with a frequency of approximately every two years. This development resulted in more compact and potent ICs. However, the amount of heat produced on a chip increased proportionally with the number of transistors. Later, in the early 2000s, Dennard Scaling broke down. Transistors became so small that leakage currents (unwanted currents that flow within the transistor) emerged as a significant issue, and they contributed substantially to power consumption and heat generation. These tightly packed transistors produced heat, which decreased their performance and shortened …

Rc Baja - Drivetrain And Chassis, Sean Drake

All Undergraduate Projects

The ASME RC Baja competition is an event held every year where mechanical engineering technology students get a chance to use their accumulated knowledge of engineering and the engineering process to design and build an RC car to compete against one another at the event. The students of Central Washington University participating in the event were paired up into teams of two to work on a car. This report will discuss the drivetrain and chassis of the car, the suspension and steering were the responsibility of the project engineer Tanner Howington.

The project included the design and analysis of the …

Rc Baja Drivetrain & Chassis, John Lange

All Undergraduate Projects

This project is centered around the development of the drivetrain and chassis for a 1/10th scale RC Baja vehicle capable of withstanding loads over the course of an RC Baja competition consisting of a solemn, drag race, and challenge course while maintaining high speeds and short acceleration times.

This project utilized 3D printing and CNC manufacturing techniques to produce a lightweight frame and efficient drivetrain. A 3800 KV brushless motor drives a two stage gearbox, which transfers force to a 90 degree locked differential to produce high torque and even application of force at low motor RPM. To support the …

R/C Baja, Tanner Howington

All Undergraduate Projects

The ASME RC Baja competition derives a need for an RC car capable of performing at a competitive level in Slalom, Sprint, and Offroad racing. To accomplish this task a suspension and steering system was designed to limit the weight of the components without compromising the structural strength, which resulted in optimizing the overall speed and stability of the vehicle. The responsibilities for optimizing the drivetrain and chassis were handled by co-engineer Sean Drake.

To ensure that each component of the suspension and steering system would hold when subjected to the expected forces, various stress analyses were performed to the …