Mechanical Engineering Commons^™

A Numerical Investigation Realizing The Flow Structure And Heat Transfer Performance Of The Potential Impinging Jets, Mohammed Sami Uddin Khan

Theses

The demand for improvement in the performance of gas turbines has led to the consideration of flows at increasingly high temperatures, but this introduces challenges in terms of maintaining their structural integrity and preventing overheating. To respond to these challenges, gas turbine manufacturers have turned to internal cooling, and jet impingement provides an effective solution for cooling the leading edge of the blades of gas turbines. In this study, the author numerically simulated the cooling performance of the leading edge of the blades of a gas turbine under constant heat flux by using five configurations of jet impingement: a steady …

A Review Of Nano And Microscale Heat Transfer: An Experimental And Molecular Dynamics Perspective, Samyabrata Chatterjee, Paras, Han Hu, Monojit Chakraborty

Mechanical Engineering Faculty Publications and Presentations

Significant progress in the development of micro and nanoscale devices has been observed for the past three decades. The thermal transportation in these small-length scales varies significantly, and it is difficult to explain the underlying physics using the pre-existing theoretical formulations. When the bulk dimension of a system is comparable to or smaller than the mean free path (MFP) of the thermal carriers, classical theories, such as Fourier’s Law of heat conduction, are unable to accurately explain the system energy dynamics. The phenomena of energy transit and conversion at the micro to nanoscale is an interesting topic of research due …

Establishing Physical And Chemical Mechanisms Of Polymerization And Pyrolysis Of Phenolic Resins For Carbon-Carbon Composites, Ivan Gallegos, Josh Kemppainen, Jacob R. Gissinger, Malgorzata Kowalik, Adri Van Duin, Kristopher E. Wise, S. Gowtham, Gregory Odegard

Michigan Tech Publications

The complex structural and chemical changes that occur during polymerization and pyrolysis critically affect material properties but are difficult to characterize in situ. This work presents a novel, experimentally validated methodology for modeling the complete polymerization and pyrolysis processes for phenolic resin using reactive molecular dynamics. The polymerization simulations produced polymerized structures with mass densities of 1.24 ± 0.01 g/cm3 and Young's moduli of 3.50 ± 0.64 GPa, which are in good agreement with experimental values. The structural properties of the subsequently pyrolyzed structures were also found to be in good agreement with experimental X-ray data for the phenolic-derived carbon …

Quantifying Balance: Computational And Learning Frameworks For The Characterization Of Balance In Bipedal Systems, Kubra Akbas

Dissertations

In clinical practice and general healthcare settings, the lack of reliable and objective balance and stability assessment metrics hinders the tracking of patient performance progression during rehabilitation; the assessment of bipedal balance plays a crucial role in understanding stability and falls in humans and other bipeds, while providing clinicians important information regarding rehabilitation outcomes. Bipedal balance has often been examined through kinematic or kinetic quantities, such as the Zero Moment Point and Center of Pressure; however, analyzing balance specifically through the body's Center of Mass (COM) state offers a holistic and easily comprehensible view of balance and stability.

Building upon …

Challenges In Optimization For The Performance On Sustainability Dimensions In Reverse Logistics Social Responsibility, Sumarsono Sudarto, Katsuhiko Takahashi, Mochammad Dewo

Makara Journal of Technology

Reverse logistics social responsibility is preferred as the most acceptable solution for addressing the challenges in stakeholders’ debate regarding social responsibility in supply chains because it involves as many actors as possible in the supply chain to perform social responsibility to achieve sustainability. This paper explores the challenges in achieving optimal policies in sustainability dimensions for collection and recycling facilities in reverse logistics. Sustainability dimensions include economic, environmental, and social aspects. The reverse logistics is modeled on System Dynamics, and a simplified statistical analysis using a contour chart is employed in numerical experiments. Results show a narrow area of optimal …

Accomplishments Of Endwall Contouring On Heat Transfer In A Passage Of A Turbine Blade, Kozhikkatil Sunil Arjun, Tide Porathoor Sunny, Narayanan Biju

Makara Journal of Technology

The study explores axisymmetric endwall contouring with emphasis on the design of novel endwalls capable of heat load reduction. Optimizations with parameterization numerically determined by the endwall of flat shape led to the endwall of the contoured shape with substantial depletion of heat transfer in the passage of the vane. Heat transfer attributes for the generated contoured endwalls were analyzed for the exit Reynolds number of 2 × 106 . Endwall three-dimensional contouring resulted in remarkable changes in secondary flow vortices, jet-to-secondary flow interaction, and film cooling effectiveness on the flat endwall. The results pointed out that the axisymmetric convergent …

Improving Irrigant Flow Characteristics For Enhanced Root Canal Therapy: A Numerical Study, Bibek Banjaday

Masters Theses

This numerical study investigates the flow characteristics within a root canal during a manual endodontic treatment. To underscore the difference in root canal geometry, a simplified root canal (frustum of a cone) and a more complex (realistic) root canal geometry were considered. The needle utilized in all simulations is a side-vented 30G KerrHaweIrrigation Probe, KerrHawe SA, Bioggio, Switzerland. For both root canal geometries, the effect of variation of fluid inlet velocity, needle insertion depth, and needle tilt angle on flow characteristics was examined via velocity contours, turbulent intensity, wall shear stress, and streamline and vector plots. The fluid was Sodium …

Calculating The Difference In Stiffness Of Living T Cells Through Micropipette Aspiration, Minju Lee

McKelvey School of Engineering Graduate Student Theses & Dissertations

Cardiovascular disease (CVD) accounted for 17.9 million deaths in 2019, with fibrosis contributing to nearly a quarter of these fatalities [1,2]. Fibrosis, characterized by excessive connective tissue formation, has been strongly linked to T cells, essential components of the immune system. This study explores the mechanisms of T cell activation and the subsequent changes in biophysical properties like diameter, stiffness, and elasticity, aiming to develop therapeutic strategies for fibrosis-related diseases, including CVD. Utilizing the micropipette aspiration technique, we accurately assessed T cell stiffness and observed a change in bulk cell stiffness upon activation. The results demonstrated increased fluid-like behavior in …

Design And Implementation Of An Instrument Package For Measuring Process Conditions In An Expeller, Md Masud Rana

LSU Master's Theses

The expeller process variable has gained increasing attention in research to validate process flow models. The expeller process is a mechanical method used to extract oil and water from seeds, nuts and polymers. Various factors, such as the speed of the press, size, and shape of the expeller, temperature, pressure, and moisture content, impact the efficiency and quality of the oil and water extraction process. By understanding these variables, researchers can develop accurate process flow models to predict the efficiency and quality of the oil and water extraction process. In this research, A custom instrumentation package have designed and implemented …

Real-Time Length Sensing Of Braided Pneumatic Actuator Using Ir Time-Of-Flight Sensor, Luon B. Chung

Dissertations and Theses

Braided Pneumatic Actuators (BPAs) are used widely in robotics as artificial muscles because of their similar characteristics to biological muscles. When a BPA is pressurized, it expands in the radial direction and contracts in the longitudinal direction. The contraction generates a pulling force that is dependent on the input pressure and BPA length. Biological muscle also behaves in the same way where a pulling force is generated on a contraction. To control BPAs on a robot, the real-time pressure and length measurements are necessary. In this dissertation, I present a new method to measure length of BPAs in real-time using …

Structural Configuration Of Amorphous Silica Surface With Different Terminating Groups Using Classical And Ab Initio Molecular Dynamics, Md Azharul Islam

Student Theses and Dissertations

Silica has numerous applications across various sectors of technology, including concrete production, glass production, food additives, and semiconductor technology. The surface interaction properties of amorphous silica are crucial, yet many aspects of these interactions, particularly with passivating groups, are still not fully understood because amorphous silica’s nature is non-periodic. In this study, computational simulations are used to understand the bonding mechanism and atomic structure of the amorphous silica surfaces with different passivating groups. Amorphous silica surfaces are generated by melt-quench dynamics using classical molecular dynamics (MD). Then, subdomains of these surfaces containing an undercoordinated surface atom are selected for ab …

Enhancing Human Key Point Identification: A Comparative Study Of High-Resolution Vicon Dataset And Coco Dataset Using Bpnet, Bibash Lama

Masters Theses

Accurately identifying human key points is crucial for various applications, including activity recognition, pose estimation, and gait analysis. This study presents a high-resolution dataset created using the VICON motion capture system and three differently oriented 2D cameras, that can be used to train different neural networks for estimating the 2D key joint positions of the person from the 2D images or videos. The participants in the study included 25 healthy adults (17 males and 8 females) performing normal gait movements for about 2 to 3 seconds. The VICON system captured 3D ground truth data, while the three 2D cameras collected …

Hierarchical Based Classifcation Method Based On Fusion Ofgaussian Map Descriptors Foralzheimer Diagnosis Using T1‑Weighted Magnetic Resonance Imaging, Nourhan Zayed, Shereen E. Morsy, Inas A. Yassine

Mechanical Engineering

Alzheimer’s disease (AD) is considered one of the most spouting elderly diseases. In 2015, AD is reported the US’s sixth cause of death. Substantially, non-invasive imaging is widely employed to provide biomarkers supporting AD screening, diagnosis, and progression. In this study, Gaussian descriptors-based features are proposed to be efcient new biomarkers using Magnetic Resonance Imaging (MRI) T1-weighted images to diferentiate between Alzheimer’s disease (AD), Mild Cognitive Impairment (MCI), and Normal controls (NC). Several Gaussian map-based features are extracted such as Gaussian shape operator, Gaussian curvature, and mean curvature. The aforementioned features are then introduced to the Support Vector Machine (SVM). …

A Multi-Aerial Vehicle Platform For Testing Collaborative Mobility Formation Controllers, Matthew Snellgrove

LSU Master's Theses

Multi-agent systems have potential applications in a multitude of fields due to their ability to perform complex tasks with a high degree of robustness. Decentralized systems are multi-agent systems where sensing, control, and communication responsibilities are distributed amongst the agents giving this scheme a particularly high potential for robustness, adaptability, and complexity; however, this comes with its own list of challenges. Formation control is a topic in multi-agent systems that aims to have the agents moving as a virtual rigid body through space. In the literature, there have been successful implementation of formation control algorithms on robot agents in both …

Extreme Cooling Via Sweeping Gas Membrane Distillation, David M. Warsinger

School of Mechanical Engineering Faculty Publications

Thermal desalination processes like membrane distillation (MD) aim to have rapid evaporation rates to provide large quantities of fresh water. These processes, which resemble counterflow-heat exchangers with membranes in the middle, conventionally seek to maximize vapor mass transfer while minimizing all other modes of heat transfer as “thermal losses.” However, we can reverse this fundamental design need to make an exceptionally high throughput heat dissipation device. By using thin thermally conductive membranes and extremely rapid air flow rates, membrane heat exchangers inspired by MD can dissipate heat several times faster than conventional air-cooled heat exchangers. We demonstrate this new approach …

Modeling Of Heat And Mass Transfer In Flat Heat Pipes, Salar Saadatian

LSU Doctoral Dissertations

Phase-change phenomenon is ubiquitous in nature and widely utilized in thermal management of computer chips. Flat heat pipes have been extensively used in thermal management of microelectronic devices. However, existing research mainly concentrates on developing numerical models and lacks a systematic analytical approach to elucidate the working mechanism of flat heat pipes. We consider a horizontal flat heat pipe with an idealized porous wick. The pores in the wick are straight circular capillaries running along and across the wick and are filled with a liquid. The rest of the pipe is filled with its vapor. The mass evaporative rate at …

On The Design And Power Output Response Of Hydraulic Wind Turbines, Helber Antonio Esquivel-Puentes, Andrea Vacca, Venkatesh Pulletikurthi, Ali Doosttalab, Jose Garcia-Bravo, David M. Warsinger, Leonardo P. Chamorro, Luciano Castillo

School of Mechanical Engineering Faculty Publications

Standard horizontal axis wind turbines typically use gearboxes for large-scale applications and direct coupling for small-scale designs to connect the rotor to the generator. However, gearboxes pose challenges due to their weight, cost, and exposure to dynamic loads and vibrations within the nacelle. A promising alternative is replacing mechanical transmission with a hydrostatic counterpart, offering advantages such as reduced nacelle mass, generator placement at the tower base, and elimination of the gearbox. It can potentially lead to cost savings of up to 20% in the levelized cost of electricity for offshore wind turbines. This study compares regulated hydrostatic transmission with …

Explainable Ai For Tool Wear Prediction In Turning, Saleh Valizadeh Sotubadi, Rui Liu, Vinh Nguyen

Michigan Tech Publications

This research aims develop an Explainable Artificial Intelligence (XAI) framework to facilitate human-understandable solutions for tool wear prediction during turning. A random forest algorithm was used as the supervised Machine Learning (ML) classifier for training and binary classification using acceleration, acoustics, temperature, and spindle speed during the orthogonal tube turning process as input features. The ML classifier was used to predict the condition of the tool after the cutting process, which was determined in a binary class form indicating if the cutting tool was available or failed. After the training process, the Shapley criterion was used to explain the predictions …

Experimental Analysis On Effects Of Inclination And Direction On Supercritical Carbon Dioxide Heat Transfer For Internal Pipe Flow, Emmanuel Gabriel-Ohanu

Electronic Theses and Dissertations, 2020-2023

Supercritical carbon dioxide (sCO2) can be utilized as a working or heat transfer fluid in various thermal systems with applications in large-scale power cycles; portable power production units, coolant systems and devices. However, there are no sufficient methods and equations of heat transfer coefficient correlations, and in addition insufficient research studies about the mechanisms controlling heat transfer processes for sCO2. This study is motivated by the need to understand the intricate properties of sCO2 heat transfer and fluid dynamics with an emphasis on flow direction and inclination effects. This paper presents the study on effects of gravity, buoyancy on sCO2 …

Stochastic Modeling Of Physical Drag Coefficient – Its Impact On Orbit Prediction And Space Traffic Management, Smriti Nandan Paul, Phillip Logan Sheridan, Richard J. Licata, Piyush M. Mehta

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Ambitious satellite constellation projects by commercial entities and the ease of access to space in recent times have led to a dramatic proliferation of low-Earth space traffic. It jeopardizes space safety and long-term sustainability, necessitating better space domain awareness (SDA). Correct modeling of uncertainties in force models and orbital states, among other things, is an essential part of SDA. For objects in the low-Earth orbit (LEO) region, the uncertainty in the orbital dynamics mainly emanate from limited knowledge of the atmospheric drag-related parameters and variables. In this paper, which extends the work by Paul et al. (2021), we develop a …

Power Packet Networks For Wave Energy Converter Arrays, David G. Wilson, Raymond H. Byrne, Steven F. Glover, Tu Anh Nguyen, Rush Robinett, Wayne Weaver, Et. Al

Michigan Tech Patents

One of the biggest challenges for all renewable energy sources (RES) is that they are variable power generators which will require reactive power or energy storage systems (ESS) to provide reliable power quality (ideally power factor of one) at the power grid generation side. The present invention is directed to a power packet network (PPN) for integrating wave energy converter (WEC) arrays into microgrids. Specifically, an array of WECs can be physically positioned such that the incoming regular waves will produce an output emulating an N-phase AC system such that the PPN output power is constant. ESS requirements are thereby …

Prediction Of Transient Hydrogen Flow Of Proton Exchange Membrane Electrolyzer Using Artificial Neural Network, Mohammad Biswas, Tabbi Wilberforce, Mohammad A. Biswas

Mechanical Engineering Faculty Publications and Presentations

A proton exchange membrane (PEM) electrolyzer is fed with water and powered by electric power to electrochemically produce hydrogen at low operating temperatures and emits oxygen as a by-product. Due to the complex nature of the performance of PEM electrolyzers, the application of an artificial neural network (ANN) is capable of predicting its dynamic characteristics. A handful of studies have examined and explored ANN in the prediction of the transient characteristics of PEM electrolyzers. This research explores the estimation of the transient behavior of a PEM electrolyzer stack under various operational conditions. Input variables in this study include stack current, …

Heat And Mass Transfer Modeling Of High-Temperature Moving-Bed Thermochemical Reactors, David Korba

Theses and Dissertations

With the global deployment of renewable energy generation at record rates, clean energy is steadily becoming competitive with its fossil-fuel counterparts. However, further expansion is limited by the inherent intermittency of renewable energy sources (solar, wind, wave, etc.), which typically do not match with daily and seasonal variations of global (and local) energy demand. Thermochemical energy storage (TCES) has demonstrated strong potential in being a technological pathway to provide on-demand process heat and handle the intrinsic variations in renewable energy generation and energy demand. TCES works on the premise of excess renewable heat driving an endothermic reduction reaction, in which …

Multi-Objective Design Optimization Of Two Configurations Of Ventricular Shunts For Hydrocephalus, Will Kirkpatrick

Theses and Dissertations

Hydrocephalus is developed when the flow of cerebrospinal fluid is obstructed in the ventricles and a pressure build-up is generated within the brain. Ventricular shunts are used to remove excess fluid from the brain, but these shunts have a common problem of failure due to the shunt being obstructed by the build-up of astrocytes. To address this, two sets of 27 designs of ventricular shunts were identified and analyzed with parameters that could potentially reduce obstruction risks. The performance of these designs was examined using fluid simulations on these two sets of 27 designs. One set explored close-tipped shunt designs, …

Nanoscale Modeling Of Membrane Systems Under Mechanical Deformation In Traumatic Brain Injury Using Molecular Dynamics, Anh Thi Ngoc Vo

Theses and Dissertations

Neuronal membrane disruption and mechanoporation are nanoscale damage mechanisms that critically affect brain cell viability during traumatic brain injury (TBI). These nanoscale cellular impairments are elusive in experiments and necessitate in silico approaches such as molecular dynamics (MD) simulations. Implementing MD, this research aims to investigate the effects of different key factors related to membrane deformation and damage, including force field resolutions, lipid compositions, and loading conditions.

To examine the impact of force field resolution, MD deformation simulations were conducted on 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) lipid bilayer membranes, using all-atom (AA), united-atom (UA), and coarse-grained Martini (CG-M) force fields. The mechanical responses …

Effects Of Machining Parameters Of C45 Steel Applying Vegetable Lubricant With Minimum Quantity Cooling Lubrication (Mqcl), Mayur A. Makhesana, Prashant J. Bagga, Kaushik M. Patel, Jaime Taha-Tijerina

Informatics and Engineering Systems Faculty Publications

One of the most significant performance indicators for measuring the machinability of materials is tool wear and surface roughness. Choosing the best combination of cutting parameters can help reduce production costs, which is what the manufacturing industry is interested in. At the same time, industries are always looking for an alternative to conventional flood cooling since its use creates an environmental burden and health concerns for the operators. Therefore, vegetable oil-based minimum quantity cooling lubrication (MQCL) is considered a cutting environment. Sunflower oil is utilized as base fluid in MQCL and applied to the cutting zone through a nozzle. The …

Influence Of Forming Forces On Torsional, Tensile, And Compressive Deformation Of Paperboard Packages, Arvo Niini, Panu Tanninen, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Paperboard packages were tested mechanically to investigate influence of forming forces on torsional, tensile, and compressive deformation. The packages were paperboard trays which were press formed with different pressing forces and blank holder forces. Deformation of the trays was observed with torsion, compression, and tensile tests. A statistical analysis of test results was conducted to derive optimal forming forces. Increased pressing force yielded desirable deformation characteristics with the trays. Blank holder force had largest impact on the compressive deformation. Interaction of the pressing force and the blank holder force influenced the torsional and the compressive deformation. The optimal forming forces …

A Robust Model Reduction For The Optimal Boundary Feedback Stabilization Of Magnetizable Piezoelectric Beams, Md Rafi As Sadeq Ibn Emran

Masters Theses & Specialist Projects

The one-dimensional Partial Differential Equation (PDE) model of the wave equation, which describes wave dynamics of a wide-range of controlled mechanical systems, with a state feedback controller at its boundary is known to have exponentially stable solutions. Moreover, it is also reported that the several model reductions of the wave equation by the standard Finite Differences and Finite Elements approximations suffer from the lack of exponential stability (and exact observability without a state feedback controller) uniformly as the discretization parameter tends to zero. This is due to the loss of a uniform gap among the high-frequency eigenvalues as the discretization …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Hemodynamic Assessment Of Y-Incision Aortic Root Enlargement Using Computational Simulations, Astitwa Ghimire

Electronic Theses and Dissertations

The Yang procedure is a new aortic root enlargement technique used to enlarge the aortic annulus by multiple valve sizes. The procedure prevents patient prosthesis mismatch and establishes a viable platform for future valve-in-valve implantation. This study used the Yang procedure to investigate the hemodynamics in the aortic root and bioprosthetic valve regions after aortic root enlargement. Results indicate the velocity magnitude at the sinus regions of a patient who underwent the Yang procedure was slower, indicating risks of flow stasis and thrombosis. Simulation results denote computational models can be created for optimization of surgical procedures.