Mechanical Engineering Commons^™

Mems Cantilever Biosensors Driven By Fringe Effect: Voltage-Amplitude Response Of Parametric Resonance, Miguel A. Martinez, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with voltage-amplitude response of fringing field/effect actuated micro-electromechanical system (MEMS) cantilever beam resonator biosensors at parametric resonance. The system consists of a flexible electrode (cantilever beam) and a fixed electrode (ground plate) in parallel, connected through an AC voltage source. The electrostatic force induced is due to the parallel-plate capacitance, which is directly related to the overlapping area of the two electrodes (Palmer’s Formula). In addition, fringing field electrostatic actuation must be accounted for. This is due to the bending of electric field lines from the ground plate to the top and side walls of the cantilever …

Amplitude-Voltage Response Of Parametric Resonance Of Electrostatically Actuated Circular Membranes, Marcos Alipi, Dumitru I. Caruntu

Mechanical Engineering Faculty Publications

This paper deals with the amplitude-voltage response of parametric resonance of electrostatically actuated MEMS circular membranes resonator for sensing applications. The system consists of a flexible circular membrane over a parallel ground plate. A soft AC voltage is applied between the MEMS membrane and ground plate to actuate the membrane near its first natural frequency. Two methods of investigation are used in this research, namely the method of multiple scales (MMS), and the reduced order model (ROM). These methods were used to solve for the voltage response of the MEMS analytically and numerically. This work also reports the effects the …

Kinematic Analysis Of Gait And Deep Knee Flexion For Pre- And Post-Operative Total Knee Arthroplasty, Samantha Collins

Electronic Theses and Dissertations

Osteoarthritis (OA) is a form of arthritis that develops in the joint due to overuse and aging causing pain, discomfort, and disability. Total Knee Arthroplasty (TKA) is a surgical procedure performed when OA symptoms are severe with an estimated 600,000 patients in the United States currently receiving TKA. Studies have reported dissatisfaction of the knee for 14-39% of patients. This study collected knee kinematics before and after surgery using stereo radiography for precise measurement of gait and deep knee flexion activities. Results showed healthy knee kinematics were not restored and no significant changes could be seen from OA kinematics in …

Exploration Of Motion Capture System To Investigate Human Shoulder Kinematics, Ola Alsaadi

Electronic Theses and Dissertations

The glenohumeral joint (GH) is commonly conceptualized as a ball-and-socket joint [1], and its center of rotation (COR) is presumed to coincide with the geometric center of the medial-superior region of the humeral head [2]. Recent research has endorsed improvements in COR estimation through invasive and noninvasive techniques, including cadaver studies, stereophotogrammetry, and motion capture (MOCAP) systems. Despite increased interest in wearable technology within human movement analysis, the problem of COR estimation employing MOCAP systems and its validation against bi-planar fluoroscopy remains relatively unexplored.

This study employed a marker-based MOCAP system to compare the accuracy, error, and precision of three …

Computational Methodology For Generating Patient-Specific Soft Tissue Representations, Ahilan Anantha Krishnan

Electronic Theses and Dissertations

This dissertation focused on modeling specimen-specific soft tissue structures in the context of joint replacement surgery. The research addressed four key aspects. The first study involved developing a workflow for creating finite element models of the hip capsule to replicate its torque-rotational response. Experimental data from ten cadaveric hips were used to calibrate the models, resulting in improved accuracy and relevance for surgical planning and implant design. The second study tackled the challenge of expediting the calibration of mechanical properties of the hip capsule to match patient-specific laxities. A statistical shape function model was proposed to generate patient-specific finite element …

Digital Twins Of The Living Knee: From Measurements To Model, Thor Erik Andreassen

Electronic Theses and Dissertations

Modern medicine has dramatically improved the lives of many. In orthopaedics, robotic surgery has given clinicians superior accuracy when performing interventions over conventional methods. Nevertheless, while these and many other methods are available to ensure treatments are performed successfully, far fewer methods exist to predict the proper treatment option for a given person. Clinicians are forced to categorize individuals, choosing the best treatment on “average.” However, many individuals differ significantly from the “average” person, for which many of these treatments are designed. Going forward, a method of testing, evaluating, and predicting different treatment options' short- and long-term effects on an …

Analysis Of Bombyx Mori Silk And Polyimide Nanofibers, Sabrina Leseul

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a study on the properties of Bombyx Mori silk nanofibers and polyimide (PI) nanofibers. Firstly, a Bombyx Mori silk solution has been created with degummed silkworm cocoons in order to separate the fibroin and the sericin, the two main proteins of the silk. The fibroin was then centrifuged to remove insoluble particles and stored and 4°C before mixing with hexafluoroisopropanol (HFIP). On the second part, a polyimide solution, made with shavings of polyimide and N,N-dimethylformamide (DMF). Both solutions are then electrospun. Electrospinning parameters are studied. In this way, a part of my thesis has been dedicated to …

Applications Of Femtosecond Laser-Processed And Nanoneedle-Synthesized Surfaces To Enhance Pool Boiling Heat Transfer, Peter Efosa Ohenhen

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, the integration of femtosecond laser surface processing (FLSP) with copper hydroxide on hybrid surfaces was examined. The goal was to determine the impact on pool boiling enhancement. The samples for the investigation were fabricated by first functionalizing with FLSP, and the process was then followed by citric acid cleaning (CAC) to eliminate the oxides generated on the copper surface during the FLSP process. After the citric acid cleaning, the samples were immersed in ethanol and subjected to an ultrasonic bath for 25 minutes. This step was performed to eliminate any residual citric acid and loose particles. …

A Generalized Machine Learning-Based Classifier Considering Cost-Effective Features For Automated Fault Detection And Diagnosis (Afdd) Of Packaged Rooftop Units, Md Rasel Uddin

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Packaged rooftop units (RTUs) are widely used for space conditioning in commercial buildings and manufacturing facilities. The typical soft faults related to RTUs degrade the system's performance in terms of cooling capacity, power consumption, and Coefficient of Performance (COP), detrimentally affecting both the equipment and energy consumption and the environment. Previous research in soft fault detection for rooftop units lacked classifier validation using lab and field data, developing a generalizable algorithm, and analyzing its performance across varying fault intensities.

Using a simulated data library for multiple rooftop units, this study proposes a machine-learning classifier with a reduced set of 9 …

Data And Cad Models Of Cyclic Testing Of Membrane Hinges For Use In Origami-Inspired Design, Mitchel Skinner

ScholarsArchive Data

The following includes results and CAD models of cyclic testing of membrane hinges for use in origami-inspired design. The results include the number of cycles until both visual damage and complete failure occurred in 7 different membrane materials. The CAD models of the testing setup are also included.

A Review On The Coalescence Of Confined Drops With A Focus On Scaling Laws For The Growth Of The Liquid Bridge, Sangjin Ryu, Haipeng Zhang, Udochukwu John Anuta

Department of Mechanical and Materials Engineering: Faculty Publications

The surface–tension-driven coalescence of drops has been extensively studied because of the omnipresence of the phenomenon and its significance in various natural and engineering systems. When two drops come into contact, a liquid bridge is formed between them and then grows in its lateral dimensions. As a result, the two drops merge to become a bigger drop. The growth dynamics of the bridge are governed by a balance between the driving force and the viscous and inertial resistances of involved liquids, and it is usually represented by power–law scaling relations on the temporal evolution of the bridge dimension. Such scaling …

Dependence Of The Granulometric Composition Of Chalk During Granulation In A Turbulized Layer, N.A. Annaev, S.Kh. Nurmukhamedov, Zh.V. Sultonov, N.Sh. Khudoiberdieva

Chemical Technology, Control and Management

The article presents the results of an experimental study on chalk granulation in the turbulized layer of a turboblade granulator. The design of the apparatus combines the following sequential processes: grinding, granulating and compacting newly formed granules. In addition, this device has the ability to carry out both rotational and reciprocating motion. It has been established that preliminary grinding of the feedstock increases the efficiency of the granulation process and improves the quality of the finished product. In the experiments, four substances were used to create 2 astringent suspensions and the optimal combination and their ratios were determined. The experiments …

Revealing Interface-Assisted Plastic Anisotropy Via In Situ Transmission Electron Microscopy Tension Of Lamellar Tial, Zhixiang Qi, Qi Zhu, Jian Wang, Yuede Cao, Fengrui Chen, Jiangwei Wang, Yang Chen, Gong Zheng, Guang Chen

Department of Mechanical and Materials Engineering: Faculty Publications

Assembling functional units into specific orientation organizations based on functional unit and organization (FUO) paradigm can maximize utilizing mechanical property anisotropy of lamellar-structured materials. However, the origin of their anisotropic deformation behaviors has not been clearly understood. Taking the fully lamellar γ-TiAl/ α₂-Ti₃Al dual-phase single crystal as an example, we decouple the interface functional units governed anisotropic plastic deformation through in situ transmission electron microscopy tensile testing and multiscale microstructural characterizations. The orientation organization-dependent slip continuity across the γ/α₂ interface and interface strength play a determinant role in plastic anisotropy beyond intrinsic dislocation activities within …

Top-Down Nanomanufacturing Of Anisotropic Two-Dimensional Metals, Md Rubayat-E Tanjil

USF Tampa Graduate Theses and Dissertations

Two-dimensional (2D) materials have introduced a transformative era in materials science with extensive research being performed to gain a fundamental understanding of their diverse properties and applications. Amongst the broader 2D material family, 2D metals or 2D metallic nanosheets (2DMNSs) typically denotes the nanometer-scale thin elemental metals, compound, or alloys, which shows superlative chemical and physical properties compared to bulk counterparts due to the reduced dimensionality. 2D materials’ widespread direct physical or chemical isolation techniques have been facilitated due to their intrinsic van der Waals layered morphology, whereas 3D close-packed bulk metals with isotropic bonding hinder their facile isolation in …

Onshore Power For The Docked Container Vessels In Apapa Port Through Blended Finance, Oladayo Matthew Atilola

World Maritime University Dissertations

No abstract provided.

Potential Roles Of Vessel Traffic Services (Vts) In Maritime Decarbonization, Suleiman Mustapha Bunza

World Maritime University Dissertations

No abstract provided.

Analysis Of The Pros And Cons Of The Acquisition Of Training Ships By Metis, Jeremiah Yaw Frimpong

World Maritime University Dissertations

No abstract provided.

Exploring The Role Of Education In Addressing The Skills Gap For Seafarers In Bangladesh's Maritime Industry, Fatema Tuz Tahera

World Maritime University Dissertations

No abstract provided.

Harnessing Multimodal Sensory Feedback: An Exploration Of Rhythmic Asymmetric Cues In Gait Rehabilitation, Scott J. Bartlett Jr.

USF Tampa Graduate Theses and Dissertations

Stroke remains a leading cause of long-term disability, with survivors often facing challenges in mobility, particularly gait asymmetry. This adversity not only diminishes the quality of life but also imposes substantial socioeconomic burdens. Current rehabilitation methods are somewhat effective yet exhibit a dire need for augmentation to better address gait abnormalities. The novel introduction of Auditory Rhythmic Asymmetric Cues, Tactile Rhythmic Asymmetric Cues, and their simultaneous combination (A-RAC, T-RAC, and AT) offers a fresh perspective toward gait rehabilitation, aimed at taking steps to alleviate the adversities borne by stroke survivors. This study provides a thorough investigation of these asymmetric cues, …

Application Of Wind Propulsion In The Existing Fleet Of The Caspian Sea Using Real Wind Data, Mahmud Suleymanli

World Maritime University Dissertations

No abstract provided.

Mining Multibeam Transit Data For Deep Ocean Polymetallic Nodules: Case Study In Se Pacific Ocean, Mark E. Mussett

USF Tampa Graduate Theses and Dissertations

Occurrences of nodules on the seafloor represent benthic habitats and present potential deposits of economically important metals. Better understanding their extent throughout Earth’s oceans will aid in resource management and determining different factors which influence their formative factors and respective local characteristics. Multibeam bathymetry and backscatter data, along with auxiliary data suggest an area of seafloor near the Foundation Seamount chain in the southern Pacific Ocean, centered around -36.84° latitude, -119.75° longitude, contains a previously uncharted polymetallic nodule occurrence. Our analysis of Simrad EM12 DUAL (12 kHz) multibeam data, collected during a 1997 transit, shows an area of strong backscatter …

Knowledge Integration In Domain-Informed Machine Learning And Multi-Scale Modeling Of Nonlinear Dynamics In Complex Systems, Phat K. Huynh

USF Tampa Graduate Theses and Dissertations

Nonlinear dynamical systems have been extensively used to model various phenomena in the changing world around us, especially in science and engineering fields. Thanks to breakthrough advancements in sensing technologies, an increasingly high volume of multi-modal sensor data has been collected, which enables us gain better insights into complex systems dynamics and build sophisticated data-driven machine-learning-based dynamic models without having the access to the underlying governing equations. However, integrating domain-specific knowledge in machine learning algorithms remains pivotal for various reasons: it promises enhanced predictive accuracy, better model interpretability, and increased generalizability. This dissertation delves into three core research questions, each …

Structural Health Monitoring And Repair Of Welded Thermoplastic Composite Joints Using Embedded Multifunctional Films, Wencai Li

LSU Doctoral Dissertations

Thermoplastic composites (TPCs) have gained widespread use, particularly in large or integrated structural components, necessitating effective joining techniques. Fusion bonding (welding) has emerged as a suitable method for TPCs due to their ability to be reshaped through heating and cooling, eliminating the need for mechanical fasteners, long curing times, and extensive surface preparation. Among the welding techniques, ultrasonic welding (USW) stands out for its fast-cycling time and potential for automating large-scale structures, thereby reducing energy consumption. However, limited industrial applications of USW in this context require further knowledge to instill confidence in the process. Moreover, composite structures are susceptible to …

Steerable Acoustically Powered Starfish-Inspired Microrobot, Cornel Dillinger, Justin Knipper, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Soft polymeric microrobots that can be loaded with nanocargoes and driven via external field stimuli can provide innovative solutions in various fields, including precise microscale assembly, targeted therapeutics, microsurgery, and the capture and degradation of unwanted wastewater fragments. However, in aquatic environments, it remains challenging to operate with microrobotic devices due to the predominant viscous resistances and the robots’ limited actuation and sensing capabilities attributed to their miniaturization. The miniature size prevents the incorporation of onboard batteries that can provide sufficient power for propulsion and navigation, necessitating a wireless power supply. Current research examines untethered microrobot manipulation using external magnetic, …

Influence Of Technological Parameters On Chip Formation And Chip Control In Precision Hard Turning Of Ti-6al-4v, Elshaimaa Abdelnasser, Samar El-Sanabary, Ahmed Nassef, Azza Barakat, Ahmed Elkaseer

Mechanical Engineering

This article presents the results of an experimental investigation into the effect of process parameters in the precision hard turning of Ti-6Al-4V on chip morphology at both macro and micro levels. It also reports on the control of chip generation to improve chip evacuation and breakability at the macro level by varying the process parameters, namely, feed rate, cutting speed and depth of cut during turning tests. A scanning electron microscope (SEM) was used to examine the chips produced for a better understanding of chip curling mechanisms at the micro level. Surface roughness of the machined specimens was measured to …

Development Of Surrogate-Optimization Models For A Novel Transcritical Power Cycle Integrated With A Small Modular Reactor, Yili Zhang, Jacob Bryan, Geordie Richards, Hailei Wang

Mechanical and Aerospace Engineering Student Publications and Presentations

In recent years, various types of surrogate optimization models have been proposed to reduce the computational time and to improve the emulation accuracy. In this study, by leveraging an ANN surrogate model developed earlier, a comprehensive and efficient optimization algorithm is conceived for the global optimal design of an integrated regenerative methanol transcritical cycle. It combines a unique converging/diverging classifier model into the surrogate model to form a surrogate-based model, which significantly improves the prediction accuracy of the objective function. Six binary classifiers are explored and the multi-layer feed-forward (MLF) neural network classifier is selected. In addition, within the five …

Effect Of Fire Flame On Some Mechanical Properties Of Self-Compacting Concrete, Haider Sadiq M. Ali, Nabeel A-M. Albayati, Basman R. Mohammed, Adil M. Jabbar

Al-Esraa University College Journal for Engineering Sciences

This paper presents an experimental investigation of the effect of fire flame on self-compacting concrete. The experimental program included casting cylinder and prism concrete specimens for compressive strength, modulus of elasticity, modulus of rupture, and concrete density tests. The specimens are exposed to fire flame at 800 ºC approximately for 2 hours or 6 hours. Then the specimens were cooled either in a fast or slow manner. Test results show that the compressive strength was reduced by about (54 - 61)% for fire exposure of 6 hours and by (27 - 37)% for 2 hours of exposure and cooled slowly …

Manual Preparation Of Eyeglasses Based On Corneal Topographical Images For Keratoconus Patients, Bassma Sabah Majeed, Faiz F. Mustafa, Nebras H. Ghaeb

Al-Esraa University College Journal for Engineering Sciences

keratoconus (KCN) is a non-inflammatory, progressive thinning process of the cornea. It is considered one of the advanced biomechanical changes on the corneal surface, and methods of treatment in late cases are special designed contact lenses or surgical intervention. The objective of this paper is to customize the standard eyeglass lens in a way so that it fits with the abnormal shape and changes of the surface of the cornea of a patient suffering from KCN disease.The proposed method here, based on manual scratching of the external surface of the standard eyeglass lens under supervising of an expert optometrist, where …

Age-Friendly Educational Buildings Primary Schools In Kerbala - A Case Study, Anwar Fadhil Hussein, Ibrahim Jawad Kadhim

Al-Esraa University College Journal for Engineering Sciences

The concept of age-friendly societies has gained international attention among researchers, policy makers, and community organizations since the World Health Organization launched the Friendly Communities Project in 2006, to address challenges in some countries, as these challenges affect all aspects of society, and the educational environment represents an important joint of those joints, being the environment that is the most effective and influential in shaping human behavior. The age stage that is most affected and capable of learning and shaping behavior is of importance, which is the childhood stage. Therefore, the research focused on school buildings, as they represent an …

The Role Of Enhancing Interaction With The Natural Environment In Achieving Social Interaction For Children In Orphanage Institutions, Shamael M. W. Al Dabbagh, Zainab Khalid Rashad Al Khafaji

Al-Esraa University College Journal for Engineering Sciences

The child deprived of family care is considered the child most in need of attention and care. When the orphan child enters a new environment for him, it is obvious that he feels alienated, isolated, and loses the sense of interaction and communication with society. The research sees the possibility of mitigating this feeling by enhancing interaction with the natural environment within the internal spaces of the orphanage building and at the neighborhood level. In order to solve the research problem, the research adopted a hypothesis stating that "interaction with the natural environment enhances the achievement of social interaction for …