Open Access. Powered by Scholars. Published by Universities.®

Mechanical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2022

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 1 - 30 of 1657

Full-Text Articles in Mechanical Engineering

Nozzle Reactive Hydroturbine With Guide Device, O O. Bozarov, Kh S. Usarov, R Aliyev, S F. Ergashev Dec 2022

Nozzle Reactive Hydroturbine With Guide Device, O O. Bozarov, Kh S. Usarov, R Aliyev, S F. Ergashev

Technical science and innovation

The article presents the principle of operation of a jet turbine with a nozzle based on the "Segner" wheel and studies its shortcomings. In order to eliminate the identified shortcomings, a guide device was developed, which is installed inside the hydraulic turbine impeller. Using the Bernoulli equations and the Zhukovsky theory, the energy parameters of a microhydroelectric power station with a developed divertor device and the water flow rate in a hydroturbine are determined. The energy parameters calculated on the basis of theoretical results are analyzed, and it is found that the efficiency of a hydroturbine increases by 10-20% depending …

Go to article

Analysis Of Ore Hand-Crushed Size Distribution For Grinding Process In The Artisanal And Small-Scale Gold Mines Production: A Case Study Of Nholi Mine, Bahi District, Malugu Tembo Dec 2022

Analysis Of Ore Hand-Crushed Size Distribution For Grinding Process In The Artisanal And Small-Scale Gold Mines Production: A Case Study Of Nholi Mine, Bahi District, Malugu Tembo

Tanzania Journal of Engineering and Technology (TJET)

(ASGM) employed numbers of people compared to large-scale mines. The ASGM has been played a crucial role in poverty alleviation and rural development, particularly in developing countries. The mined ore is crushed and ground for beneficiation of gold. The grinding process involved the size reduction of blasted materials to acquire minerals of interest. This paper presents the size distribution of hand-crushed for blasted materials using sieve analysis and digital image processing. The sieve test results for hand-crushed blasted material of three muck-piles were ranged between 17 mm and 36 mm that is equivalent to 20% and 80% passings respectively, with …

Go to article

Synthesis, Characterisation And Catalytic Evaluation Of Castor Oil-Templated Mesoporous Sulfated Solid Acid Catalysts For Esterification Reaction, Steven Nyandoro Pr Dec 2022

Synthesis, Characterisation And Catalytic Evaluation Of Castor Oil-Templated Mesoporous Sulfated Solid Acid Catalysts For Esterification Reaction, Steven Nyandoro Pr

Tanzania Journal of Engineering and Technology (TJET)

In bio-refinery and other catalytic reactions, heterogeneous catalysts confer advantage over homogenous catalysts due to minimized recovery and separation costs. However, templating surfactant and solid support for the synthesis of heterogeneous catalysts ought to consider their cheap sources and environmentally friendliness for their sustainable use. Thus, with the vision to make the process significantly benign, in the present work, solid acids were synthesised from renewable sources (castor oil as surfactant and rice husk as the source of silica). The synthesised castor oil-templated mesoporous sulfonic acid modified catalysts (SO3H-MTS and SO3H-MT-RHS) were characterised and evaluated for catalytic esterification of acetic acid …

Go to article

Optimization Of Pulsed Laser Deposition Parameters For Single Crystalline (011) Oriented Tetragonal Pzt Thin Films, Mahamudu H. Mtebwa Dec 2022

Optimization Of Pulsed Laser Deposition Parameters For Single Crystalline (011) Oriented Tetragonal Pzt Thin Films, Mahamudu H. Mtebwa

Tanzania Journal of Engineering and Technology (TJET)

Recent advances in nanotechnology applications require the processing of high-quality thin films. A systematic study of the optimization of Pulsed deposition parameters for (110) oriented tetragonal PZT thin films is reported in this work. Prior to film deposition, a highly tetragonal Pb(Zr0.5, Ti0.95) or PZT 05/95 was selected to be deposited on (110) oriented Strontium titanate, SrTiO3 substrate, STO(110) to insure small compressive misfit strain. Unlike SRO, the LSOM bottom electrode was then successfully grown at 620 °C, 1.0 J/cm2 and a target-substrate distance of 3.9 cm. Finally, deposition parameters of PZT were progressively optimized through monitoring film morphological changes. …

Go to article

Energy Assessment Of E-Motorcycles As A Clean Transport Mode For Passenger Mobility: A Case Of Ilala District, Dar Es Salaam, John Shirima Dec 2022

Energy Assessment Of E-Motorcycles As A Clean Transport Mode For Passenger Mobility: A Case Of Ilala District, Dar Es Salaam, John Shirima

Tanzania Journal of Engineering and Technology (TJET)

Electric motorcycles or e-motorcycles is a clean mode of road transport that present a prominent solution toward decarbonizing cities. Despite of e-motorcycles being cleaner than gasoline ones, at the moment, there is missing information whether it is feasible to replace gasoline motorcycles with e-motorcycles used for business transport purposes. This paper, therefore, presents the results comparing energy usage when using e-motorcycles and when using the gasoline motorcycles. The energy demand for driving passengers using an e-motorcycle in the precarious routes originated from Gongo la Mboto bus stop to Segerea bus stop, Buguruni Malapa, Gerezani bus stop, Kivukoni bus stop, and …

Go to article

Interrogating The State Of Application Of Technology Within The Malawi Maritime Force As Maritime Expression : A Task-Technology Fit Approach, Gift William Kamwendo Dec 2022

Interrogating The State Of Application Of Technology Within The Malawi Maritime Force As Maritime Expression : A Task-Technology Fit Approach, Gift William Kamwendo

World Maritime University Dissertations

No abstract provided.

Go to article

Coconut Shell Waste Treatment Technology For A Sustainable Waste Utilization: A Case Study Of The Smes In Bohol Village, Indonesia, Wahyu Anggo Rizal, Ria Suryani, Roni Maryana, Dwi Joko Prasetyo, Diah Pratiwi, Yuli Ary Ratnawati, Dini Ariani, Andri Suwanto Dec 2022

Coconut Shell Waste Treatment Technology For A Sustainable Waste Utilization: A Case Study Of The Smes In Bohol Village, Indonesia, Wahyu Anggo Rizal, Ria Suryani, Roni Maryana, Dwi Joko Prasetyo, Diah Pratiwi, Yuli Ary Ratnawati, Dini Ariani, Andri Suwanto

ASEAN Journal of Community Engagement

This project focused on the introduction of liquid smoke and bio briquette manufacturing technology to small and medium enterprises (SMEs) located in Bohol Village, Gunungkidul, Indonesia through technology transfer, training, and mentoring. These SMEs are engaged in the food business with the main product jenang ketan, a traditional food from Gunungkidul, especially in Rongkop District, and very popular among communities around and outside Gunungkidul. The traditional preparation of jenang ketan produces several by-products in the form of waste, which is dominated by coconut shell biomass. The project’s technology transfer was carried out through the procurement of a series of pyrolysis …

Go to article

Urban Farming: Empowerment To Increase Economic, Education, And Nutritional Benefit For The Sub-Urban Community, Nasruddin Nasruddin, Yusuf Donner Dwiyantama, Banu Muhammad, Anom Bowalaksono, Dian Ayubi, Sarah Islamiati Pertiwi Dec 2022

Urban Farming: Empowerment To Increase Economic, Education, And Nutritional Benefit For The Sub-Urban Community, Nasruddin Nasruddin, Yusuf Donner Dwiyantama, Banu Muhammad, Anom Bowalaksono, Dian Ayubi, Sarah Islamiati Pertiwi

ASEAN Journal of Community Engagement

This article discusses the urban farming program at Sekolah Master in Beji, Depok, Indonesia, which aims to provide the community with broader benefits, such as economy, education, and increased nutritional value. The project involves planting method that was introduced to this school community. The program itself consists of several stages, starting from the preparation—dissemination of the program and designing a plan for the greenhouse, the implementation—constructing the greenhouse and installing the automatic water system, planting the vegetation, and monitoring and evaluation of the program. Eventually, an evaluation of the successful program is required to determine whether the program can be …

Go to article

Properties Of (Cd, Zn)S Films Deposited By Dc Co-Sputtering, Lwitiko P. Mwakyusa Dec 2022

Properties Of (Cd, Zn)S Films Deposited By Dc Co-Sputtering, Lwitiko P. Mwakyusa

Tanzania Journal of Engineering and Technology (TJET)

CdS thin film is commonly used as a buffer layer in most thin film solar cells. However, the buffer layer with less absorption in the visible region of the solar spectrum as well as that which provides perfect lattice matching with the absorbers is required. The incorporation of Zn in the CdS films can affect the structural and optical properties of the buffer layer. In this work, films of CdS and (Cd,Zn)S films were deposited by DC sputtering utilizing CdS and Zn targets. The concentration of Zn in the CdS was varied by changing the sputtering power of the Zn …

Go to article

Review Of The Imaging Performance And The Current Status Of The Cascade Gamma-Rays Coincidence Imagers, Leonid L. Nkuba Dr. Dec 2022

Review Of The Imaging Performance And The Current Status Of The Cascade Gamma-Rays Coincidence Imagers, Leonid L. Nkuba Dr.

Tanzania Journal of Engineering and Technology (TJET)

Various studies that have investigated the detection of gamma coincidence events have revealed that design factors and image reconstruction approaches dictate the spatial resolution, coincidence efficiency, and levels of statistical noise of the detection system. In the case of imaging, cascade gamma-ray coincidence (CGC) imagers coupled with collimated detectors offer promising values for both spatial resolution and coincidence efficiency. However, to date, no CGC imager with single or multiple collimated detectors has reported a performance level beyond 6.7 mm spatial resolution (FWHM) and 6.0 × 10-6 coincidence efficiency. Given the recent developments and the current interests in high resolution and …

Go to article

Lead Acid Battery Recycling In The Current Tanzania Industrialization Drive: Challenges And Opportunities, Divina D. Kaombe Dec 2022

Lead Acid Battery Recycling In The Current Tanzania Industrialization Drive: Challenges And Opportunities, Divina D. Kaombe

Tanzania Journal of Engineering and Technology (TJET)

ABSTRACT Advancements in automotive technologies, Information and Communications Technology and renewable energy technologies have increased the use of lead acid batteries as a source of portable and rechargeable energy. This has considerably increased the number of spent batteries with adverse effects on the environment and human health; which calls for recycling of spent batteries. This work was conducted to investigate challenges facing the formal business of recycling spent batteries and potential manufacturers of new lead-acid batteries in Tanzania. The work involved collection of information from key stakeholders such as collectors, dealers, Tanzania Revenue Authority and recyclers. It was found out …

Go to article

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo Dec 2022

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Go to article

Comparative Analysis Of Injection Of Pyrolysis Oil From Plastics And Gasoline Into The Engine Cylinder And Atomization By A Direct High-Pressure Injector, Magdalena Szwaja, Jeffrey Naber, David Shonnard, Daniel G. Kulas, Ali Zolghadr, Stanislaw Szwaja Dec 2022

Comparative Analysis Of Injection Of Pyrolysis Oil From Plastics And Gasoline Into The Engine Cylinder And Atomization By A Direct High-Pressure Injector, Magdalena Szwaja, Jeffrey Naber, David Shonnard, Daniel G. Kulas, Ali Zolghadr, Stanislaw Szwaja

Michigan Tech Publications, Part 1

The article discusses the results of experimental studies on the course of pyrolysis oil injection through the high-pressure injector of a direct-injection engine. The pyrolysis oil used for the tests was derived from waste plastics (mainly high-density polyethylene—HDPE). This oil was then distilled. The article also describes the production technology of this pyrolysis oil on a laboratory scale. It presents the results of the chemical composition of the raw pyrolysis oil and the oil after the distillation process using GC-MS analysis. Fuel injection tests were carried out for the distilled pyrolysis oil and a 91 RON gasoline in order to …

Go to article

Bio-Inspired Micromachined Volumetric Flow Sensor With A Big Dynamic Range For Intravenous Systems, Lansheng Zhang, Yingchen Yang, Georgios A. Bertos, Chang Liu, Huan Hu Dec 2022

Bio-Inspired Micromachined Volumetric Flow Sensor With A Big Dynamic Range For Intravenous Systems, Lansheng Zhang, Yingchen Yang, Georgios A. Bertos, Chang Liu, Huan Hu

Mechanical Engineering Faculty Publications

Real-time monitoring of drug delivery in an intravenous infusion system can prevent injury caused by improper drug doses. As the medicine must be administered into the vein at different rates and doses in different people, an ideal intravenous infusion system requires both a low flow rate and large dynamic range monitoring. In this study, a bio-inspired and micromachined volumetric flow sensor is presented for the biomedical application of an intravenous system. This was realized by integrating two sensing units with different sensitivities on one silicon die to achieve a large dynamic range of the volumetric flow rate. The sensor was …

Go to article

Three-Component Composite Phase-Change Material For Thermal Regulation, Bidisha Ojha Dec 2022

Three-Component Composite Phase-Change Material For Thermal Regulation, Bidisha Ojha

McKelvey School of Engineering Graduate Student Theses & Dissertations

Phase change materials can increase the efficiency of many energy-intensive applications, such as solar power plants, solar heating and cooling systems, heat recovery systems, photovoltaic electricity systems, and Earth satellite systems. In several proposed thermal management systems for high power electronic equipment, PCMs change phase and absorb latent heat at peak energy loads during operation, then dissipate this energy later to prevent overheating. More specifically, composite PCM’s, consisting of an organic material (e.g., paraffin) and an inorganic material (e.g., metallic alloys or salt hydrates), provide a superior balance of thermal conductivity and latent heat for thermal management. Organic PCMs have …

Go to article

Developing An In Vitro Validated 3d In Silico Internal Carotid Artery Sidewall Aneurysm Model, Hang Yi, Zifeng Yang, Mark Johnson, Luke Bramlage, Bryan Ludwig Dec 2022

Developing An In Vitro Validated 3d In Silico Internal Carotid Artery Sidewall Aneurysm Model, Hang Yi, Zifeng Yang, Mark Johnson, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Introduction: Direct quantification of hemodynamic factors applied to a cerebral aneurysm (CA) remains inaccessible due to the lack of technologies to measure the flow field within an aneurysm precisely. This study aimed to develop an in vitro validated 3D in silico patient-specific internal carotid artery sidewall aneurysm (ICASA) model which can be used to investigate hemodynamic factors on the CA pathophysiology. Methods: The validated ICASA model was developed by quantifying and comparing the flow field using particle image velocimetry (PIV) measurements and computational fluid dynamics (CFD) simulations. Specifically, the flow field characteristics, i.e., blood flowrates, normalized velocity profiles, flow streamlines, …

Go to article

Phase-Averaged, Frequency Dependence Of Jet Dynamics In A Scaled Up Vocal Fold Model With Full And Incomplete Closure, Nathaniel Wei, Abigail Haworth, Hunter Ringenberg, Michael Krane, Timothy Wei Dec 2022

Phase-Averaged, Frequency Dependence Of Jet Dynamics In A Scaled Up Vocal Fold Model With Full And Incomplete Closure, Nathaniel Wei, Abigail Haworth, Hunter Ringenberg, Michael Krane, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

This study focuses on frequency dependence effects on glottal jet dynamics with a focus on the physiological condition in which the vocal folds do not fully close. Incomplete closure occurs naturally in children and adult females. But there are also pathological conditions that can be problematic. Experiments were conducted using a 10× scaled-up model in a free surface water tunnel. Two-dimensional vocal fold models with semicircular medial surfaces were stepper motor driven inside a square duct with constant opening and closing speeds. Cases with complete vocal fold closure and incomplete closure to only 15% of the maximum gap were examined. …

Go to article

Sars-Cov-2 Detecting Rapid Metasurface-Based Sensor, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Khaled Aliqab, Meshari Alsharari, Ammar Armghan Dec 2022

Sars-Cov-2 Detecting Rapid Metasurface-Based Sensor, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Khaled Aliqab, Meshari Alsharari, Ammar Armghan

Department of Mechanical and Materials Engineering: Faculty Publications

We have proposed a novel approach to detect COVID-19 by detecting the ethyl butanoate which high volume ratio is present in the exhaled breath of a COVID-19 infected person. We have employed a refractive index sensor (RIS) with the help of a metasurface-based slotted T-shape perfect absorber that can detect ethyl butanoate present in exhaled breath of COVID-19 infected person with high sensitivity and in-process SARS-CoV-2. The optimized structure of the sensor is obtained by varying several structure parameters including structure length and thickness, slotted T-shape resonator length, width, and thickness. Sensor’s performance is evaluated based on numerous factors comprising …

Go to article

Three Dimensional Cfd Simulation Model With Experimental Validation Of Silica Gel–Water Pair Adsorption Cooling Bed, Hesham Safwat, Taher Halawa Dec 2022

Three Dimensional Cfd Simulation Model With Experimental Validation Of Silica Gel–Water Pair Adsorption Cooling Bed, Hesham Safwat, Taher Halawa

Mechanical Engineering

In this paper, a three-dimensional full simulation model of a solar-driven adsorption cooling system integrated with user-defined functions (UDF) is successfully validated with a manufactured adsorption chamber filled with silica-gel type A. model is validated on the desorption phase with a maximum deviation error of 1.7%. Temperature with adsorption contours are shown for more understanding of the heat flow with adsorption behaviour inside the chamber in all directions. The maximum temperature at the desorption phase is reached after 300 seconds at fins area, and adsorption maximum uptake reached 0.16 kg/kg at fins wall but reached from 0.13 to 0.14 kg/kg …

Go to article

The Musical Water Fountain, Amy Nielsen Dec 2022

The Musical Water Fountain, Amy Nielsen

Honors Theses

An affordable musical water fountain was designed over the course of one year. The target consumers for this fountain are middle to upper class homeowners. Based on the design parameters and research found on the topic, the fountain presents an aesthetically pleasing light and water show for residential neighborhoods. The design was sought to be competitive on the market with preexisting fountains. Since it must play music and perform a water and light show all in synchronous, there was confidence in the unique features to sell with today’s consumers. SolidWorks was used extensively to design and model the fountain and …

Go to article

Wind-Powered Continuous Reverse Osmosis Water Desalination, Aliah Adriana Binti Khairul Hisham Dec 2022

Wind-Powered Continuous Reverse Osmosis Water Desalination, Aliah Adriana Binti Khairul Hisham

Discovery Undergraduate Interdisciplinary Research Internship

Water scarcity is a grave issue that is faced by lots of people worldwide. This phenomenon is further exacerbated by climate change, overpopulation, and water-intense industrial activities. To combat this issue, reverse osmosis (RO) water desalination system is broadly introduced in order to produce freshwater while maintaining the desired thermodynamic efficiency and economic feasibility. RO water desalination is a process of separating freshwater from salt water using a semi-permeable membrane. In status quo, there are various forms of energy present in RO system (e.g: hydraulic, mechanical, electrical energy, etc.) to power the hydraulic components. The conversion from one form of …

Go to article

Energy Dissipation In A Sand Damper Under Cyclic Loading, Ehab Sabi Dec 2022

Energy Dissipation In A Sand Damper Under Cyclic Loading, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Various seismic and wind engineering designs and retrofit strategies have been in development to meet structures' proper and safe operation during earthquake and wind excitation. One such method is the addition of fluid and particle dampers, such as sand dampers, in an effort to reduce excessive and dangerous displacements of structures. The present study implements the discrete element method (DEM) to assess the performance of a pressurized sand damper (PSD) and characterize the dissipated energy under cyclic loading. The idea of a PSD is to exploit the increase in shearing resistance of sand under external pressure and the associated ability …

Go to article

Experimental And Numerical Studies On Laser Hot Wire Cladding By A High-Power Direct Diode Laser, Mingpu Yao Dec 2022

Experimental And Numerical Studies On Laser Hot Wire Cladding By A High-Power Direct Diode Laser, Mingpu Yao

Mechanical Engineering Research Theses and Dissertations

Laser hot wire cladding is an advanced surface modification technology. It has been extensively growing during the last decades due to its high deposition rate, good metallurgical bonding between the substrate and clad layer, low dilution ratio, and small heat-affected zone. There are many kinds of lasers widely used in the laser cladding process. The high-power direct diode laser is widely welcomed because of its high energy efficiency, high electro-optic conversion efficiency, low cost, and high reliability. A rectangular-shaped direct diode laser beam combined with hot wire feeding can achieve a lower dilution depth with a uniform fusion line compared …

Go to article

Novel Locomotion Methods In Magnetic Actuation And Pipe Inspection, Adam Cox Dec 2022

Novel Locomotion Methods In Magnetic Actuation And Pipe Inspection, Adam Cox

Mechanical Engineering Research Theses and Dissertations

There is much room for improvement in tube network inspections of jet aircraft. Often, these inspections are incomplete and inconsistent. In this paper, we develop a Modular Robotic Inspection System (MoRIS) for jet aircraft tube networks and a corresponding kinematic model. MoRIS consists of a Base Station for user control and communication, and robotic Vertebrae for accessing and inspecting the network. The presented and tested design of MoRIS can travel up to 9 feet in a tube network. The Vertebrae can navigate in all orientations, including smooth vertical tubes. The design is optimized for nominal 1.5" outside diameter tubes. We …

Go to article

On The Effects Of Geometrical And Fluid Conditions On Thermal-Hydraulics Of Miniature Heat Sinks, Mahyar Pourghasemi Dec 2022

On The Effects Of Geometrical And Fluid Conditions On Thermal-Hydraulics Of Miniature Heat Sinks, Mahyar Pourghasemi

Mechanical Engineering ETDs

During the past three years, miniature heat sinks have been integrated into the cooling loop of devices such as MW-class gyrotron resonators and high-power laser arrays. These applications involve high cooling rates in the range of 20-25 MW/m2. Liquid metals such as Na and NaK offer very high thermal conductivity in the range of 16-79 W/mK, while their dynamic viscosities are only slightly higher than water viscosity. They can also be used in applications with operating temperatures varying from 25 oC to as high as 800 oC due to their very high boiling points. Several research …

Go to article

Cyber-Secure Distributed Control Of Microgrids With Improved Communication And Control Protocols, Jee Won Choi Dec 2022

Cyber-Secure Distributed Control Of Microgrids With Improved Communication And Control Protocols, Jee Won Choi

Mechanical Engineering ETDs

This dissertation proposes a cyber-secure distributed control of microgrids with improved communication and control protocols. The finite-time event-triggered control protocol for islanded AC and DC secondary control is introduced. For AC microgrids, the proposed strategy can effectively perform frequency restoration and voltage regulations while sharing the active and reactive power among the distributed generators (DGs) based on their power ratings. For DC microgrids, the proposed control protocol can provide accurate current sharing and critical bus voltage regulation. The finite-time control enables a system to reach a consensus in a finite period of time enhanced from asymptotic convergence. The event-triggered communication …

Go to article

Adaptive Analytic Continuation For The State Transition Tensors Of The Two-Body Problem, Tahsinul Haque Tasif Dec 2022

Adaptive Analytic Continuation For The State Transition Tensors Of The Two-Body Problem, Tahsinul Haque Tasif

Electronic Theses and Dissertations, 2020-2023

In the past few decades, Kessler syndrome (named after Donald J. Kessler) has become a point of concern in the field of Space Situational Awareness and the future of space missions. It refers to a scenario, where space debris in Earth's orbits collides and creates an exponential increase in space debris numbers leading to more collisions and more debris. In order to handle the resulting challenges like conjunction analysis, tracking, and probability of collisions, the State Transition Matrix (STM) and Tensors (STTs) of the orbit problem play a significant role. In addition, STM and STTs are ubiquitous in spaceflight dynamics, …

Go to article

Processing And Characterization Of Ultra High Temperature And High Conductive Composites, Haonan Song Dec 2022

Processing And Characterization Of Ultra High Temperature And High Conductive Composites, Haonan Song

Electronic Theses and Dissertations, 2020-2023

There are significant challenges for materials in extreme environments for a variety of applications such as aircraft engines, gas turbines, nuclear reactors, re-entry vehicles, and hypersonic structures. Ceramic matrix composites (CMCs) could be ideal candidates to meet these stringent requirements for materials due to their high melting temperatures, high oxidation, corrosion and ablation resistance, low creep, and thermal cycling behavior in such extreme environments. Particularly, continuous fibers can bridge cracks in CMCs and therefore improve the strength and fracture toughness of composites. Metal matrix ceramics are important materials in various industries, such as aerospace and automobile. MMCs have excellent mechanical …

Go to article

Investigation Of The Effect Of Corundum Layer On The Heat Transfer Of Sic Slab, Sri Elsa Fatmi, Donanta Dhaneswara, Muhammad Anis, Ahmad Ashari Dec 2022

Investigation Of The Effect Of Corundum Layer On The Heat Transfer Of Sic Slab, Sri Elsa Fatmi, Donanta Dhaneswara, Muhammad Anis, Ahmad Ashari

Journal of Materials Exploration and Findings

Aluminum is the most widely used metal in industry. Aluminum smelting is one of the important steps that needs to be carried out to produce products made of aluminum metal with good quality. In the process of smelting aluminum there are several problems that occur, one of which is the growth of corundum in Si C refractories which affects the quality of aluminum melt and the durability of Si C refractories. This research was conducted to see the heat transfer in Si C and the effect of the presence of Corundum on heat transfer. This research was carried out by …

Go to article

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo Dec 2022

Structural Risk-Based Underwater Inspection (Rbui) As A Cost Reduction Of Field’S End Of Production Life, Ivan Fitrian Putra, Johny Wahyuadi Soedarsono, Mirza Mahendra, Yuki Haidir, Faisal Dwiyana Purnawarman, Iwan Sukirna, Widi Hernowo

Journal of Materials Exploration and Findings

Mubadala Petroleum operates offshore platforms in a southern Makassar Straits that needs to be periodically inspected. The cost for the inspection is massive due to the high cost of mobilization and demobilization of vessels including crew and equipment. In response of a new approach to reduce cost, a Risk-Based Underwater Inspection (RBUI) methodology is developed. This RBUI purpose is to reduce the inspection interval of the offshore platform, from every 2 years to a longer period[1]. There are existing RBUI methodologies, which are already developed and implemented in other companies[5]. Purpose of this paper is to …

Go to article

Next Last