Mechanical Engineering Commons^™

Feasibility Study Of Radio Frequency Microelectromechanical Filters For Space Operation, Karanvir Singh

Theses and Dissertations

Piezoelectric contour mode resonator technology has the unique advantage of combining low motional resistance with the ability to define multiple frequencies on the same substrate. Contour mode resonators can be mechanically coupled together to form robust band-pass filters for the next generation of GPS satellites with extreme size reduction compared to electrically coupled filters. Piezoelectric zinc oxide (ZnO) contour mode resonators have the potential for monolithic integration with current ZnO transistor further reducing size, power consumption, and cost of filter modules. Barium strontium titanate (BST) contour mode resonators have incredible frequency tunability due to the fundamental nature of the thin …

Bi-Directional Kerr-Lens Mode-Locked Titanium Sapphire Laser, Ricky Arnold, Stratos Koutroulis, Dylan Meyer

Mechanical Engineering Senior Theses

Precision near-infrared absorption spectroscopy is a highly desired scientific method, but the blooming technology has not yet come to fruition. Field deployments are limited, and some methods come with limitations that hamper the viability. The laser cavity completed for this thesis project is a single cavity Dual Comb Spectroscopy laser, which improves myriad limiting characteristics of previous lasers in this application. Crucially, it can produce two simultaneous pulse trains with unique repetition rates. The laser cavity has been designed, built, and aligned for improved stability, including vibrational, noise, and thermal control. The design, analysis, and results of a dual comb …

Pod Stabilization, Lane Matthew Pledger, Becca Stefanich, Ian Mccandless, Patrick Salter, Kirk Kuran

General Engineering

We were tasked by Holmes Solutions to find a way to stabilize their patented SWITCHBACK passenger gondola system. This system is a self-propelled pod that transitions smoothly between cables and rails. The main goal for this project is to dampen side-to-side swing of gondola pods using a modular stabilization system. This device must be within these constraints: it must fit within a work envelope, must be safe for user and operator, must perform a dampening effect, and must be compliant with the current system. We formulated many ideas to achieve the goal, including making the pod more aerodynamic, adding sliding …

Consumer-Ready Insulated Solar Electric Cooker, Simon Ford, Sachin Gokhale, Brendan Lynn, Richard Nguyen

Mechanical Engineering

An insulated solar electric cooker, or ISEC, converts solar energy into electricity to cook food, boil water, provide heat or even help charge batteries. In this project, the focus is an ISEC with a phase change material (PCM) that helps store heat when the solar energy input is minimal, such as after the sun has set. Although a successful ISEC already exists that utilizes PCM, this product can be improved in many ways. The specific revisions investigated in this report are the improvement of the thermal efficiency with the implementation of a vacuum-sealed outer pot, the reduction of the overall …

Interactive Physics Display: Air Cannon, Marina Smeltzer, Sydney Hosokawa, Jordan Nguyen, Jessica Ouyang

Mechanical Engineering

The San Luis Obispo Botanical Garden (SLOBG) is a non-profit organization that provides a place for visitors to connect with and explore nature. The sponsors from SLOBG sought an interactive physics display to be implemented in their children’s garden that will educate children and adult visitors about physics concepts in a welcoming and comfortable atmosphere. The research done showed that customers are looking for a “wow” factor with the display to surprise and engage them. Patents showed the design and build of interactive playground equipment. Government reports described the curriculum for the target audience and also outlined the safety precautions …

Sustainable Energy Storage, Jacob S. Grillo, Alyse C. Coonce, Jack R. Linchey, Nick P. Schnorr

Mechanical Engineering

This Final Design Review document covers the work we, students at California Polytechnic State University – San Luis Obispo, have performed in collaboration with Mr. Harish Bhutani and Dr. Mohammad Noori. The project’s intent is to create an energy storage system for off-grid and developing region applications using alternative technologies to lithium-ion battery storage. We plan to manufacture and assemble a scale model of the energy storage system to prove effectiveness and practicality. This system will store enough energy to power basic appliances and essential devices for a house or community. The chosen design direction will be a flywheel, as …

Configurable Seat Track Latching Mechanism, Emily Sun, Kai Quizon, Rick Hall, Daniel Turn, Nicholas Holman, Alexander Kuznik, Jacob Winkler, Audrey Trejo, Phoebe Zeiss, Steven Kam

Mechanical Engineering

The reconfigurable seating system is a flexible seating solution for transit vehicles that allows operators to change the configuration of the floor plan in a timely manner in order to accommodate change in needs. This project consists of three senior project teams each working on a component of the design: system, track & latch, and articulation. Descriptions of the responsibilities of each team will be discussed below.

Prosthetic Foot Shell, Christopher Menke, Colton Arbuckle, Jacob Rodriguez

Mechanical Engineering

Prosthetic foot shells are designed to fit around lower limb prosthetics to be able to fit shoes and several types of footwear. They are currently designed in a way that they wear through very quickly if used in an active lifestyle. The current designs on the market are designed for geriatric use. The sponsor for this project Mr. Dana Cummings, would like for the team to produce a product that extends current foot shell’s life. This document explains includes the team’s research process, the design process, and the main functions of what the team designed for. It will also show …

Composite Pegboard, Asa J. Cusick, Luis Corrales, Joelle Hylton, Wyatt Pauley

Mechanical Engineering

Many of those with mobility limitations who are told they will need a wheelchair for the rest of their lives can actually begin to stand and walk again given the proper tools and support. The current design for a wheelchair seeking to support this process is overly complex, heavy, and exhibits some features that could potentially pose a serious health hazard to those using it. The scope of this project is to aid in the design of an adaptable composite wheelchair frame that can be both lightweight and strong, while still allowing for physical diversity of potential users. Through research …

Transportable, Jung Sub Kim, Ellie Kitabjian, David Yang, Christopher Macias

Mechanical Engineering

This document is a Final Design Review (FDR) report for team TransporTable, a quartet of mechanical engineers at California Polytechnic State University, San Luis Obispo (Cal Poly). It chronicles our design and validation process through final design phase. Our project: to design and test concepts for a stackable table that streamlines group work. After conducting user/sponsor interviews and background research, we found that many products already exist, but none meet the specific blend of requirements set out by our sponsor. They include fast deploying/stowing times, durability, stiffness, and manufacturability. We ideated on the table’s functions, distilling many ideas into three …

Space Suit Attachment Quick Release System, Elyse C. Gillis-Smith, Andres I. Elzaurdia, Cole H. Stanton, Michael T. Roth

Mechanical Engineering

NASA plans to make it back to the Moon by 2024 with their Artemis Program, and stay there for a longer period of time to conduct research which will support the future of space exploration. While on the lunar surface, astronauts need to maximize their efficiency by carrying tools on their Exploration Extravehicular Mobility Unit (xEMU), and to accommodate this need, the Extravehicular Activity (EVA) Tools Team is pursuing a utility belt concept. The objective of this project is to develop a system capable of interfacing between the utility belt and any given tool, while also accommodating numerous restrictions and …

Uav For Medical Equipment Distribution, Richard Barakat, Logan Christensen, Brandon Halebsky, Justin Slavick

Mechanical Engineering

This Final Design Review report documents the senior project participating in the Vertical Flight Society’s 38th Annual Student Design Competition sponsored by The Boeing Company. The goal of this project and competition is to develop an unmanned vertical lift for medical equipment distribution capable of safely delivering a 50 kg payload over distances up to 200 km. This system must be autonomous and have a backup plan to land if any part of the system malfunctions. We discuss the research and justification that drove the selection of the aircraft configuration, a winged quadcopter with a rear propeller. Furthermore, we document …

Hands-On 3d Printed Dynamics Activities, Dakota Baker, Jacob Lindberg, Andrew Meyenberg, Junnior Rodriguez

Mechanical Engineering

The advancement of 3D printing has allowed everyday individuals to rapid prototype and manufacture in a more efficient, cost-effective, and timely manner. This has paved the way for a more adaptable educational model, by allowing instructors to easily access alternative instruments for teaching. By providing students with tangible tools, they will better be able to grasp complex principles. Dynamics professors need a way in which they can easily access these academic tools, transport them to and from class, and teach multiple dynamics principles through variations of a single 3D printed kit. Interviews with professors and students were conducted to gain …

A Mems Pressure Sensor Using Electrostatic Levitation, Mohammad Mousavi, Mohammad Alzgool, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Applying electrostatic levitation force to the initially-closed gap-closing electrodes of our micro-electro- mechanical system (MEMS) creates multi actuation mechanisms, and opens a new world to the MEMS applications.

Electrostatic levitation allows us to measure physical quantities, such as air pressure, by exploiting pull-in instability and releasing. The beam starts from a pulled-in position by applying a voltage difference between two gap-closing electrodes. When enough voltage is applied to the side electrodes, the cantilever beam is released. At the release instant, electrostatic forces, restoring force, and surface force are applied to the cantilever. According to the experimental results of this work, …

Power Output Modeling And Optimization For A Single Axis Tracking Solar Farm On Skewed Topography Causing Extensive Shading, Logan J. Smith

Master's Theses

Many utility-scale solar farms use horizontal single axis tracking to follow the sun throughout the day and produce more energy. Solar farms on skewed topography produce complex shading patterns that require precise modeling techniques to determine the energy output. To accomplish this, MATLAB was used in conjunction with NREL weather predictions to predict shading shapes and energy outputs. The MATLAB models effectively predicted the sun’s position in the sky, panel tilt angle throughout the day, irradiance, cell temperature, and shading size. The Cal Poly Gold Tree Solar Farm was used to validate these models for various lengths of time. First, …

Failure Analysis Of The Ulnar Collateral Ligament For Youth Baseball Pitchers, Carlos Soto

Master's Theses

The objectives of this study were to (1) use kinetics from motion analysis and inverse dynamics to calculate the stress experienced by the ulnar collateral ligament (UCL) during a typical pitch cycle, (2) compare calculated maximum UCL pitching stresses to failure properties, and (3) investigate correlations between UCL stress with anthropometric and pitching biomechanical parameters. Prior motion analysis experiments of eighteen 10- to 11- year-old baseball pitchers throwing 10 fastballs were analyzed. Maximum internal elbow varus torques were calculated using inverse dynamics methods during a typical pitch cycle. Calculations used axial loading stress equations and maximum internal elbow varus torques …

Novel And Fast Peridynamic Models For Material Degradation And Failure, Siavash Jafarzadeh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fracture is one of the main mechanisms of structural failure. Corroded surfaces with chemically-induced damage are, notably, potential sites for crack initiation and propagation in metals, which can lead to catastrophic failure of structures. Despite some progress in simulating fracture and damage using classical models, realistic prediction of complex damage progression and failure has been out of reach for many decades. Peridynamics (PD), a nonlocal theory introduced in 2000, opened up new avenues in modeling material degradation and failure. Existing numerical methods used to discretize PD equations, however, are quite expensive as the PD nonlocal interactions make them unaffordable for …

A Novel Drive Cycle Simulation Model For Gasoline Engines To Investigate Bandwidth Coverage Of Emission Performance And Fuel Consumption With Engine Control Parameters, Martin Giencke

Doctoral

The presented work is offering an investigation how the bandwidth of vehicle specific attributes is impacting engine control parameter requirements for warmup control of the catalytic converter, aiming to ease the development process by providing mathematical means for an automatic generation of control settings. For the specific purpose, a novel drive cycle simulation approach is developed, focusing on emission performance and fuel consumption of a gasoline engine. Steady state and quasi steady state measurements are collected to quantify the impact of modifications to control parameters on emission concentration, exhaust gas temperature and engine torque, especially directly after a cold start. …

Reliable Mode Tracking In Gradient-Based Optimization Frameworks With Flutter Constraints, Taylor Mcdonnell, Andrew Ning

Faculty Publications

In order to construct mode-specific flutter constraints for use in gradient-based multidisciplinary design optimization frameworks, mode tracking must be used to associate the current iteration’s modes with the modes corresponding to each constraint function. Existing mode tracking methods, however, do not provide a method by which to ensure the accuracy of mode associations, making them unsuitable for use in situations where obtaining correct mode associations is critical. To remedy this issue, a new mode tracking method is presented which incorporates backtracking logic in order to maintain an arbitrarily high degree of confidence in mode correlations during gradient-based optimization and/or during …

Implementing A Data Acquisition System For The Training Of Cloud Coverage Neural Networks, Weston C. Montgomery

Master's Theses

Cal Poly is home to a solar farm designed to nominally generate 4.5 MW of electricity. The Gold Tree Solar Farm (GTSF) is currently the largest photovoltaic array in the California State University (CSU) system, and it was claimed to be able to produce approximately 11 GWh per year. These types of projections come from power generation models which have been developed to predict power production of these large solar fields. However, when it comes to near-term forecasting of power generation with variable sources such as wind and solar, there is definitely room for improvement.

The two primary factors that …

The Application Of Post-Hoc Correction Methods For Soft Tissue Artifact And Marker Misplacement In Youth Gait Knee Kinematics, Kaila L. Lawson

Master's Theses

Biomechanics research investigating the knee kinematics of youth participants is very limited. The most accurate method of measuring knee kinematics utilizes invasive procedures such as bone pins. However, various experimental techniques have improved the accuracy of gait kinematic analyses using minimally invasive methods. In this study, gait trials were conducted with two participants between the ages of 11 and 13 to obtain the knee flexion-extension (FE), adduction-abduction (AA) and internal-external (IE) rotation angles of the right knee. The objectives of this study were to (1) conduct pilot experiments with youth participants to test whether any adjustments were necessary in the …

Prediction Of In-Plane Stiffnesses And Thermomechanical Stresses In Cylindrical Composite Cross-Sections, Bryson M. Chan

Master's Theses

Accurate mechanical analysis of composite structures is necessary for the prediction of laminate behavior. Cylindrical composite tubes are a mainstay in many structural applications. The fundamental design of circular composite cross-sections necessitates the development of a comprehensive composite lamination theory. A new analytical method is developed to characterize the behavior of thin-walled composite cylindrical tubes using a modified plate theory. A generated numerical solver can predict properties such as axial stiffness, bending stiffness, layer stresses, and layer strains in composite tubes subjected to combined mechanical loading and thermal effects. The model accounts for the curvature by transforming and translating the …

Analytical, Numerical, And Computational Methods To Analyze The Time To Empty Open, Closed, And Variable-Topped Inverted Bottles, Callen Schwefler

Master's Theses

Recent unexpected experimental observations of the emptying of inverted bottles with perforations has generated interest in modeling and simulation of this phenomenon. It was observed that as a perforation, i.e., a small hole at the "top" of the inverted bottle, is added and enlarged, the overall emptying time first increases to a maximum value and then decreases until it reaches a lower limit. The change in emptying time is associated with a transition from jetting, where only water exits the neck, to glugging, a competition between air and water flows at the neck of the bottle.

This paper develops analytical …

Electric Field Induced Self-Assembly Of Mesoscale Structured Materials And Smart Fluids, Suchandra Das

Dissertations

This dissertation aims to study the forces that drive self-assembly in binary mixtures of particles suspended in liquids and on fluid-liquid interfaces when they are subjected to a uniform electric or magnetic field. Three fluid-particle systems are investigated experimentally and theoretically : (i) Suspensions of dielectric particles in dielectric liquids; (ii) Suspensions of ferromagnetic and diamagnetic particles in ferrofluids; and (iii) Dielectric particles on dielectric fluid-liquid interfaces. The results of these studies are then used to estimate the parameter values needed to assemble materials with desired mesoscale microstructures.

The first fluid-particle system studied is an electrorheological (ER) fluid formed using …

Service Quality Assessment And Improvement Methods And Tools, Kevin M. Moriarty

Dissertations

The nucleus of this research concept and system is being applied to turret lathe and milling machine Computer Numerical Control (CNC) tool systems. The research has a generic application to the service of broad array of sophisticated computer controlled / integrated machines, devices / equipment such as industrial robotics, medical equipment, surgical robots, and similar types of engineered system. Quality design review for quality service systems is a unique concept. Standard product service systems are qualitative and subjective in nature. The quantitative system identifies Key Predictive Attributes (KPAs) and applies quantitative methods to these attributes to develop a systematic process …

Private Sound Environments In Public Space: Use Of Headphones In Public Parks And Public Transit, Chathurthi S. De Silva

Dissertations

The use of headphones is now so commonplace that it is almost second nature for many people to use them. Not only do these people use headphones all the time, but they use them nearly everywhere, including in urban public spaces. In using headphones, people create their own “private sound environments” in public space. This phenomenon merits attention from researchers since the creation of private sound environments may well alter people’s experiences of public space.

This study answers five research questions about the use of headphones in parks and on transit: why people use them, when they begin using headphones …

Investigation Of Topological Phonons In Discrete Mechanical Metamaterials, Kai Qian

Dissertations

The study of topological mechanical metamaterials is a new emerging field that focuses on the topological properties of artificial mechanical structures. Inspired by topological insulators, topological mechanism has attracted intensive attention in condensed matter physics and successfully connected the quantum mechanical descriptions of electrons with the classical descriptions of phonons. It has led to experiments of mechanical metamaterials possessing topological characteristics, such as topologically protected conducting edges or surfaces without back-scattering. This dissertation presents a new experimental approach for mechanically engineering topological metamaterials based on patterning magnetically coupled spinners in order to localize the propagation of vibrations and evaluate different …

Investigation Of Two-Phase Flow Phenomena In Rotating Paper Dryer To Achieve Effective Heat Transfer With Low Energy Consumption, Hamed Abdul Majeed

LSU New Orleans Theses and Dissertations

The paper industry provides important consumer products comprised of paper, tissue, paper board, and pulping. The papermaking process requires a lot of energy, in the form of steam, to dry the paper web in rotating dryers. As steam condenses inside the dryers by releasing heat to the dryer walls, the condensate is removed using either stationary or rotary siphons. Since the condensate is usually at a saturated state, part of the condensate flashes into vapor during the extraction process and becomes difficult to extract. Thus, additional blow-through steam is used to push the condensate out. Since this blow-through steam is …

Numerical Study On Oscillating Flow Over A Flat Plate Using Pseudo-Compressibility In Intermittent Turbulent Regime, Shivank Srivastava Mr.

LSU New Orleans Theses and Dissertations

A Computational Fluid Dynamic (CFD) in-house code is developed to study unsteady characteristics of incompressible oscillating boundary layer flow over a flat plate under laminar and intermittently turbulent condition using pseudo-compressible unsteady Reynolds Averaged Navier- Stokes (RANS) model. In the in-house code, the two-dimensional, unsteady conservation of mass and momentum equations are discretized using finite difference techniques which employs second order accurate (based on Taylor series) central differencing for spatial derivatives and second order Runge-Kutta accurate differencing for temporal derivatives. The in-house code employs Fully Explicit-Finite Difference technique (FEFD) to solve the governing differential equations of the mathematical model. In …

Mitigation Of Airborne Contaminant Spread Through Simple Interventions In An Occupied Single-Family Home, Florida Solar Energy Center, Nazim Muradov

FSEC Energy Research Center®

Historically, reducing aerosol-based transmission of respired viruses in indoor environments has been of importance for controlling influenza viruses and common-cold rhinoviruses. The present public health emergency associated with SARS-CoV-2 makes this topic critically important. Yet to be tested is the potential effectiveness of simple interventions that create an isolation zone (IZ) for a suspected/confirmed sick or sensitive person requiring quarantine. The intent in existing homes is to find a practical means to mitigate exposure to airborne contaminants. In creating an IZ in an occupied single-family home in the study, four simple strategies were tested. The test configurations were: (1) IZ …