Mechanical Engineering Commons^™

Forced Convection Film Condensation Of Downward-Flowing Vapor On Horizontal Tube With Wall Suction Effect, Tong-Bou Chang, Fu-Jen Wang

Journal of Marine Science and Technology–Taiwan

The heat transfer performance of the condensate layer formed by a downward-flowing, dry saturated vapor flowing over an isothermal horizontal tube with wall suction effects is examined. Under the effects of wall suction, the gravity force, the potential flow pressure gradient, and the interfacial shear stress, the local/mean Nusselt numbers of the condensate film are obtained as a function of the Jakob number Ja, the Prandtl number Pr, the Rayleigh number Ra, the two-phase mean Reynolds number Rev, the dimensionless pressure gradient parameter P, and the suction parameter Sw. The results show that the mean Nusselt number increases with increasing …

An Examination Of The Influence Of Distillation On The Combustion Behavior Of Apparently Equivalent Surrogate Fuels, Jay A. Lefkowitz

Theses and Dissertations

Use of surrogates to emulate the combustion behaviors of prevaporized real fuels has been widely demonstrated in the literature. However, many combustion applications utilize atomized fuel sprays, and for these configurations, the assumption of fuel property homogeneity in prevaporized fuel combustion is tenuous. This work uses a simplified distilling droplet model to demonstrate a real potential for vaporization-coupled deviations from the single-valued combustion property targets used to characterize prevaporized combustion behaviors. To verify the model-based observations, flame blowout measurements from a custom-built annular spray burner rig are measured. Sets of essentially equivalent prevaporized jet fuel and gasoline surrogates suggested in …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Department Hosts Summer Camp for HS Students

Comparison Of Concrete And Steel Jacket Methods For Reinforcing A Concrete Bridge Pier By Numerical And Experimental Studies, Hadi Faghihmaleki

Makara Journal of Technology

Various rehabilitation and strengthening procedures have been developed in recent decades. A study to determine which methods can be implemented to increase the useful life of the bridge before strengthening must be performed. In this study, the seismic behavior of a reinforced concrete bridge pier with dimension 3.5 × 3.5 m, which was reinforced by two steel and a concrete jacket, was investigated. Nonlinear geometric models and materials were analyzed to estimate the seismic parameters of the pier. Results show an increase in energy absorption, ultimate strength, and ductility for the steel jacket, as well as a greater increase in …

Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang

Makara Journal of Technology

X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …

Trend Significance Levels Of Rain Onset And Cessation And Lengths Of The Wet And Dry Seasons In Epe, Lagos State, Nigeria, Adekunle Adedeji Alli, Olorunwa Eric Omofunmi

Makara Journal of Technology

This study aims to reduce crop failure resulting from a dry spell, which is the first occurrence of unsustainable rainfall that deceives farmers into planting. Thus, trends need to be tested using hypothesis, kurtosis, and other statistics to analyze the risks associated with unstable planting calendars and their possible mitigation strategies. The daily rainfall data from 1982 to 2018 were obtained from the archive of NASA/POWER SRB/FLASH, and the research location is Epe, Lagos State, Nigeria, which lies at latitude 6.585° N and longitude 3.962° E. Microsoft Excel was used to perform the tests. Results show that the null hypothesis …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …

Improvement Of Electrical Properties Of Cmc-Pva Doped With Various Contents Of Lino3 As An Application For Hybrid Polymer Electrolytes, Amalia Zulkifli, Norfatihah Mazuki, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried out with the development of hybrid polymer electrolytes (HPEs) by using carboxymethyl cellulose (CMC)–polyvinyl alcohol (PVA) doped with different contents of lithium nitrate (LiNO3) for the determination of their structural and conduction properties. The structural analysis was conducted by using Fourier transform infra-red spectroscopy and showed the interaction between the blend host polymer and ionic dopant, which formed via the coordinating site of CMC-PVA and Li+-NO3−. The complexes of CMC-PVA doped LiNO3 led to an increment in ionic conductivity, as observed by electrical impedance spectroscopy, and the sample containing 20 wt% LiNO3 obtained the highest …

Music Information Retrieval Based On Active Frequency, Hardianto Wibowo, Wildan Suharso, Yufis Azhar, Galih Wasis Wicaksono, Agus Eko Minarno, Dani Harmanto

Makara Journal of Technology

Music is the art of combining frequencies. A balance of frequencies gives rise to a harmonious tone. Several features of music can be analyzed, and they include sociocultural background, lyrics, mood, tempo, rhythm, harmony, melody, timbre, and instrumentation. In this study, we use the frequency of instrumentation as a feature for classification because each instrument has a frequency range. To test this frequency range, we use five music genres and one music playing skill. The five genres are dangdut, electronic dance music (EDM), metal, pop/rock, and reggae. The music playing skill is acoustic. Active frequencies are tested using the k-nearest …

Predictive Delivery Man Assignment Problem Using Deep Learning, Rahmadini Payla Juarsa, Taufik Djatna

Makara Journal of Technology

Dispatching is a critical part in current online shopping. It relates to how the delivery man assignment should minimize cost along with the service from a source to an end customer with an appropriate scheduled time. The problem arises as neither enough products to deliver nor delivery men are available for dispatch, resulting in suboptimal service and a waste of money. The study aimed to formulate the cost of restaurant dispatching for inducing a deep learning-based solution with the gated recurrent unit recurrent neural network to receive hourly order data and to engage the result for near feature delivery man …

An Engineer's Guide To Periodic Discrete Wavelet Transforms And The Periodic Wavelet Balance Method, Simon Jones

Faculty Publications - Mechanical Engineering

This Technical Report aims to explain how to apply the discreteWavelet Balance Method (dWBM) for solving periodic differential equations using periodized Daubechies wavelets. The primary goal is to provide the user sufficient details to implement the technique without extensive mathematical background.

Chapter 2 of this document reviews the discrete Fourier transform using a multivariate regression approach, followed by a review of the discrete Harmonic Balance Method (dHBM) for approximating solutions to periodic differential equations. It is important the reader complete this chapter, even if they are familiar with the topics, since the approaches demonstrated in Chapter 2 with harmonic functions …

Effect Of Temperature On Abrasion Erosion In Particle Based Concentrating Solar Powerplants, Nipun Goel, Tessa Mei-Lin Fong, John P. Shingledecker, Andrew Russell, Michael W. Keller, Siamack A. Shirazi, Todd Otanicar

Mechanical and Biomedical Engineering Faculty Publications and Presentations

The use of solid particles as a heat transfer medium is being explored for concentrated solar power plants (CSP) to increase their efficiency by achieving operating temperature >700 °C. During operation, these hot particles are expected to move along the various components within the collector system, resulting in material degradation from a combination of high-temperature oxidation and erosion. In the present study, the performance of candidate materials was evaluated through a series of abrasion erosion experiments at room temperature as well as at 800 °C. Wear in metallic and refractory type materials was investigated using CarboBead® HSP 40/70 particles inside …

Stress Analysis Of Functionally Graded Materials, Nilabh Krishna

Mechanical and Aerospace Engineering Dissertations - Archive

A functionally graded material (FGM) is an inhomogeneous material whose material properties vary continuously. Since FGM’s material properties are continuous at the interface of the two materials, unlike conventional composites whose material properties are discontinuous at the interface, it is best suited to prevent catastrophically failure, stress concentration, and residual stresses. Literature reviews revealed that most of the research on FGMs was a 2-D analysis, especially on FGM plates and beams. This research focuses on 3-D stress analysis for an elastic medium that contains a spherical inclusion made of an FGM embedded in a matrix phase. To the best of …

Effect Of Thermal Conductivity, Reynolds Number, Aspect Ratio And Packing Arrangement On Radial Heat Transfer In Packed Beds, Nishith Gorla

Mechanical and Aerospace Engineering Dissertations - Archive

The key motivation for this research is to study heat transfer developments in packed beds. The radial heat transfer enhancement of a packed bed in the laminar flow region is one of the major areas of ongoing research in mechanical, aerospace and chemical industries, especially the response of a packed bed during conjugate heat transfer with the fluid-solid interaction. This computational study focuses on the impact of packing size, thermal conductivity, and arrangement on the radial heat transfer performance as a function of Reynolds number. A simple annular tube packed with circles (2D) and spheres (3D) is utilized for this …

Modeling The Effect Of In Situ Nozzle-Integrated Compression Rolling On The Mechanical And Fracture Behavior Of Fused Filament Fabrication (Fff) 3d Printed Parts, Momen Mohammad Qasaimeh

Mechanical and Aerospace Engineering Dissertations - Archive

Fused filament fabrication (FFF) is one of the most common additive manufacturing/3D printing techniques where continuously extruded semi-molten filaments are deposited in a layer-by-layer manner. The quality of the manufactured part depends on some major factors such as filament-filament contact and adhesion as well as the void fraction. Filament to filament adhesion affects the part strength under transverse load. In our earlier work, we studied the effect of in situ ball rolling on the thermal and mechanical properties of the printed parts. It was found that when printing/rolling parameters are correctly tuned and in situ compression rolling is appropriately applied …

Set-Theoretic Frameworks For Online Optimization, Estimation, And Control, Dignata Bhattacharjee

Mechanical and Aerospace Engineering Dissertations - Archive

This research is primarily focused on developing online frameworks, which are suited to real-time implementation, for performance optimization, estimation, and control of dynamical systems using set-theoretic concepts and/or having set-theoretic interpretations. First, two perturbation-based extremum seeking control schemes, based on the classical setup and equipped with novel adaptation laws for the perturbation signal amplitudes, are proposed for general single input single output nonlinear systems. The proposed schemes are able to extremize steady-state system output in a practical asymptotic sense, i.e., the system is driven to an arbitrarily small set centered at the true steady-state optimal operating point. The next development …

Uncertainty Propagation, Control, And Estimation Of Stochastic Dynamic Systems Using Generalized Polynomial Chaos Expansion, Rajnish Bhusal

Mechanical and Aerospace Engineering Dissertations - Archive

In recent years, uncertainty propagation has emerged as an important research area in the field of dynamical systems. The growing interest in this area arises out of the need to develop computationally efficient approaches to predict the evolution of a system subject to uncertainties. To this end, this dissertation is focused on developing computational frameworks for uncertainty propagation, control, and state estimation of stochastic dynamical systems using the generalized polynomial chaos (gPC) expansion technique. In the first part of this dissertation, the construction of gPC expansion is presented in general. The novelty of this dissertation lies in developing a mixed …

Computational Investigation Of Energy Dissipation Through Progressive Failure In Tailored Composite Structures Via Explicit Finite Element Analysis, Anirudh Srinivas

Mechanical and Aerospace Engineering Dissertations - Archive

In this study, energy dissipation in structures implementing a previously developed, analytically modeled, and experimentally validated composite tailoring concept is investigated using an explicit finite element approach. The tailored composite structures consist in a series connection of parallel alternate load paths of tailored length and thickness. The advantage of the tailored structure when compared to an untailored conventional structure is that when subjected to a tensile load, the response of the tailored composite structure is characterized by progressive failure of the load paths resulting in increased energy dissipation. The tailored composite structure is modeled for IM7-8552 composite material using a …

Laminar Swept And Cross Shockwave/Boundary-Layer Interactions, Jiss Jacob Sebastian

Mechanical and Aerospace Engineering Dissertations - Archive

Shockwave/boundary-layer interactions are considered one of the most complex problems in high-speed gas dynamics, and numerous studies have been carried out for more than eighty years to understand the fundamental physics. A numerical study was performed using fin-plate configurations to study the three-dimensional swept and cross shockwave/ laminar boundary-layer interactions. All the interactions studied were strong enough for the boundary layer to separate. In the first part, swept shock interactions between a laminar boundary layer and the shockwave induced by a sharp fin mounted perpendicularly on a flat plate were studied. Different flow conditions were investigated at freestream Mach numbers …

Design, Operation And Maintenance Of Direct And Indirect Evaporative Cooling Systems In Data Center Thermal Management, Ashwin Siddarth

Mechanical and Aerospace Engineering Dissertations - Archive

Evaporative cooling is an alternative data center cooling solution that presents significant energy cost savings in acquisition and operation when compared to conventional air conditioning and mechanical refrigeration systems. This research focuses on developing a deeper understanding in implementing, operating and maintaining evaporative cooling systems integrated with air-side economization to realize the energy savings potential in data center cooling. The goal of the research is to develop a comprehensive guide to assess and contrast different approaches of evaporative cooling being used in data center cooling and provide guidance in improving water and energy efficiency. An air handling unit (AHU) serves …

Design Of Streamline-Traced Inlets And Their Integration With Rotating Detonation Engines, Malcolm Lee Branch

Mechanical and Aerospace Engineering Theses - Archive

This thesis has two parts: 1) design of the streamline-traced inlets (STIs); and 2) integration of STIs with rotating detonation engines (RDEs). The STI design starts with a two-dimensional, isentropic compression flowfield as the parent flowfield. The method of characteristics was used to generate the flowfield throughout the entire STI. For a given flight altitude 18 km, freestream Mach number M?=3.0, and inlet exit-plane Mach number M?=1.2, a parametric sweep of the initial deflection angle ?1=4.0--11.0 deg and the Mach number at the entrance of the internal compression system M3=1.3--1.7 was performed to determine the STI performance sensitivity as a …

Haptic Interface Optimization For Virtual Anastomosis Surgery Training, Kangji Huang

Mechanical and Aerospace Engineering Theses - Archive

Virtual anastomosis surgery study allows surgeons to perform or practice suturing in virtual reality using a commercial haptic device. The haptic device can generate force feedback so that the user can feel the real touch sensation of the object in virtual reality. The virtual anastomosis surgery study has two requirements which are that the haptic device must be fixed on the operating table and haptic device location must be suitable for different surgeons. The goal is to use a commercially available haptic device for this purpose, rather than design a new device for each possible surgery that must be performed. …

Design And Cfd Analysis Of Bimetallic Based Passive Dynamic Cold Plate For High Power Direct-To-Chip Liquid Cooling, Apurv Pravin Deshmukh

Mechanical and Aerospace Engineering Theses - Archive

Rising demand for high-performance chips results in the need for advanced and efficient cooling technologies like direct to chip liquid cooling. Cold plates based utilizing direct liquid cooling is one of the most efficient and the most investigated cooling technology since the 1980s. Major data services and cloud providers like IBM, Microsoft, and Google had already started a shift towards liquid-cooled data centers for their high computational servers. At the chip level nowadays, the processors are divided into several cores and each of these cores continuously works at varying computational demands. This creates a non-uniform heat distribution across the processor, …

Simulation Of A Soft Body Non-Grasp Manipulator Using A Spring-Mass-Damper Cloth Model, Cristian Almendariz

Mechanical and Aerospace Engineering Theses - Archive

Simulation and modeling are well known and important tools in the field of robotics, being used to validate design and in the development of robotic control systems. Traditionally, robotic systems have been primarily rigid body systems and used in well controlled environments where interactions are highly predictable, and exceptions are minimized. With the ever-increasing adoption of robotics in the medical field, typical robotic environments are becoming highly unpredictable and requiring the modeling and simulation of not only rigid body systems but soft systems and interactions between the two. This work addresses model improvement of a “soft and hard” robotic system …

Development Of Virtual Simulation For Evaluation Of Robotic Assistive Environment, Shubham Raosaheb Gunjal

Mechanical and Aerospace Engineering Theses - Archive

Robotics research in virtual simulation has the advantage of reduced testing time, verification of algorithms on different systems before implementation, and cost-saving. Today’s simulation softwares are capable of providing the physics of the simulation such as torque requirements of the joints which aid in the selection of appropriate hardware. In this research, Webots, an open-source physics-based simulation, and visualization software is evaluated and then used to study and evaluate the performance of two robotic systems for a robotic assistive environment for persons with upper limb disabilities. This includes a wheelchair, a table with objects, and two robotic arms attached to …

Investigating A Finite Element Model Updating Methodology For Characterizing Mechanical Properties Of Ncf Composites, Pasworn Chanchai

Mechanical and Aerospace Engineering Theses - Archive

Composite materials have been a key breakthrough in developing aircraft structures. Their superior strength and stiffness-to-density ratio, which are unmatched by no other materials, allow engineers to create high strength and ultra-lightweight aircraft structures. Recently, non-Crimp Fabric (NCF) composites have emerged as attractive alternatives to traditional autoclave pre-impregnated composites allowing for lower production costs, better handling and improved shelf life while maintaining excellent in-plane mechanical properties compared to other types of textile composites. NCF out-of-plane mechanical properties can also be enhanced by stitching a high tensile strength yarn throughout their entire laminate thickness, improving the resistance to delamination. However, stitch-reinforced …

Characterization And Enhancement Of Mechanical Properties In Thermoplastic Fff Parts Using In-Situ Annealing, Rhugdhrivya Rane

Mechanical and Aerospace Engineering Dissertations - Archive

Fused filament fabrication is one of the most common and widely used additive manufacturing techniques. Owing to its ease of use, availability and cheap feedstock it provides a significant advantage over other AM techniques. But these advantages are overshadowed by the fact that FFF parts show high anisotropy and reduced mechanical properties as compared to conventional manufacturing techniques. Literature review of previous research works show multiple approaches to enhance the mechanical properties of FFF parts but each of these techniques have limitations to either the geometries that can be printed or involve complex expensive setups. In one such technique a …

Shape Modeling, Attitude Estimation, And Classification Of Artificial Resident Space Objects (Rso) Using Photometric Light Curves, Katiyayni Balachandran

Mechanical and Aerospace Engineering Dissertations - Archive

Light curve inversion (LCI) has proven valuable in using photometric measurements to optimize various physical parameters of a resident space object (RSO) such as rotational period about its own spin axis, pole orientation and others. Other characteristics such as shape and size are dependent on the surface brightness. To accurately determine size, shape, spin rate, or attitude information of an unresolved resident space object, photometry is required to capture the relatively rapid changes in brightness that these objects can exhibit. LCI has been developed significantly for asteroids, although not fool-proof for artificial RSOs. Satellites and space debris, unlike asteroids, are …

Theoretical And Experimental Analysis And Optimization Of Thermal Conduction In Electrochemical And Latent Heat Energy Storage Systems, Amirhossein Mostafavi

Mechanical and Aerospace Engineering Dissertations - Archive

Phase change materials (PCMs) are used commonly for energy storage purposes. Thermal energy can be stored in a PCM with a variety of configurations such as PCM slabs, cartesian and cylindrical finned systems. Heat transfer in PCM storage systems can be from a heat transfer fluid (HTF) or a heat source at constant temperature to adjacent PCM. The rate of heat transfer is limited by thermal properties. Fin insertion can improve the heat transfer inside the PCM. Chapters 2 and 3 derive and solve the governing energy equations to determine the transient temperature distribution in the PCM due to the …

Rotor Performance Model (Rpm), Chadwick Scott Balfantz

Mechanical and Aerospace Engineering Theses - Archive

Rotorcraft performance modeling is of high interest with multiple industry codes in existence, many of which are high-fidelity and are comprehensive in the analyses that are achievable. Along with the high-fidelity and the comprehensive nature of the industry codes comes an equally high level of complexity in the inputs required to extract meaningful results. The ever-increasing fidelity in the existing codes creates a need for an analysis code that is built to be highly flexible, designed from the top down and implemented from the bottom up in a structured format. The Rotor Performance Model (RPM) was developed to provide high-fidelity …