Mechanical Engineering Commons^™

Asme Student Design Competition, Marcus Todd

Mahurin Honors College Capstone Experience/Thesis Projects

For the completion of my capstone project with the Western Kentucky University Honors College, the following document details my experience with the American Society of Mechanical Engineer (ASME) Student Design Competition. This project was completed in a two semester sequence through working with a team of four. One semester focusing primarily on the design and the other on fabrication and evaluation. The 2019 ASME competition was the Pick and Place Race. In this event, 46 teams were challenged to design and construct a device having the ability to pick up balls of varying size. Both the design and assembly process …

Magnesium Nanocomposites: An Overview On Time-Dependent Plastic (Creep) Deformation, Meysem Haghshenas, Manoj Gupta

Mechanical Engineering Faculty Publications

Magnesium (Mg) nanocomposites are created when nano-size particles are embedded into the Mg (or Mg alloy) matrix. The Mg nanocomposites, cited as high-strength energy-saving materials of future, are a group of emerging materials with excellent combination of strength and ductility and superior specific strength property (strength-to-weight ratio). Having said this, Mg nanocomposites are considered as promising replacement for other structural alloys (i.e. aluminum and titanium) wherever low density and high strength are required, i.e. transportation, aerospace, defense, etc. To be able to apply this group of materials for real components, different failure mechanisms at ambient and elevated temperatures under …

High Fidelity Dynamic Modeling And Nonlinear Control Of Fluidic Artificial Muscles, Jonathon Earl Slightam

Dissertations (1934 -)

A fluidic artificial muscle is a type of soft actuator. Soft actuators transmit power with elastic or hyper-elastic bladders that are deformed with a pressurized fluid. In a fluidic artificial muscle a rubber tube is encompassed by a helical fiber braid with caps on both ends. One of the end caps has an orifice, allowing the control of fluid flow in and out of the device. As the actuator is pressurized, the rubber tube expands radially and is constrained by the helical fiber braid. This constraint results in a contractile motion similar to that of biological muscles. Although artificial muscles …

A Comparison Of Static And Dynamic Functional Connectivities For Identifying Subjects And Biological Sex Using Intrinsic Individual Brain Connectivity, Sreevalsan S. Menon, K. Krishnamurthy

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Functional magnetic resonance imaging has revealed correlated activities in brain regions even in the absence of a task. Initial studies assumed this resting-state functional connectivity (FC) to be stationary in nature, but recent studies have modeled these activities as a dynamic network. Dynamic spatiotemporal models better model the brain activities, but are computationally more involved. A comparison of static and dynamic FCs was made to quantitatively study their efficacies in identifying intrinsic individual connectivity patterns using data from the Human Connectome project. Results show that the intrinsic individual brain connectivity pattern can be used as a ‘fingerprint’ to distinguish among …

Manipulating Transverse Photovoltage Across Plasmonic Triangle Holes Of Symmetry Breaking, Marjan Akbari, Jie Gao, Xiaodong Yang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The transverse photo-induced voltages generated by the photon drag effect under normally and obliquely incident circularly polarized light across the plasmonic symmetry-breaking isosceles-triangle holes and right-triangle holes have been characterized. It is observed that the sign of transverse photovoltage flips when the incident circular polarization is switched for both types of plasmonic triangle holes. However, the unbalanced photovoltage between two circular polarizations is achieved across the plasmonic right-triangle holes, compared to the balanced photovoltage in the plasmonic isosceles-triangle holes. Such manipulation of the sign and the amplitude of transverse photovoltage is enabled by the broken symmetries of the electric and …

Hybrid Laser/Arc Welding Of Difficult-To-Weld Thick Steel Plates In Different Joint Configurations: Issues And Resolutions, Nima Yazdian

Mechanical Engineering Research Theses and Dissertations

Difficult-to-weld steels are ferrous alloys that are characterized by a low thermal conductivity, and large thermal expansion coefficient. These intrinsic features contribute to a high level of distortion and cracking susceptibility during joining of these types of steels. In an effort to address the issues associated with difficult-to-weld steels, highly concentrated beam spots like electron and laser beam welding were developed. Usage of tightly focused heat sources have been accompanied by several challenges. An extremely precise fit-up requirement was considered as the most significant issue corresponding to application of either laser or electron beam. Recently, it was found that the …

Analytical And Experimental Study Of Laser Cladding Of Ni/Wc Metal Matrix Powders Reinforced With Rare Earth Elements Using A High Power Direct Diode Laser, Mohammed Sayeed

Mechanical Engineering Research Theses and Dissertations

The corrosion and wear are major limiting factors for steel in the harsh environments and can be controlled by depositing protective passive coatings. Nickel based alloy cladding of steel offers a solution by enabling better corrosion and wear resistance, and high bonding strength. The laser surface cladding of steel was conducted using a high power direct diode laser. Layers of tungsten carbide in Ni (40%Ni-60%WC) combined with 1% and 2% Lanthanum Oxide (La₂O₃) and Cerium Oxide (CeO₂) were deposited on ASTM A36 steel substrate. The X-ray diffraction and scanning electron microscopy were employed to …

Off Axis Compressive Response Of Ice-Templated Ceramics, Rahul Kumar Jujjavarapu

Mechanical & Aerospace Engineering Theses & Dissertations

The off-axis compressive behavior of ice-templated ceramic was analyzed using experimental results and micro-mechanical model simulation. Ice-templated ceramics is a versatile processing technique used to manufacture anisotropic ceramic foam by exploiting the anisotropic growth characteristics and lamellar morphology. The ice-templating process results in processing-structure-property relationships determined by the microstructure. The processed alumina samples which were later manufactured by water jet machine from the freeze casting were tested under quasi-static off-axis loading conditions and were used to determine the mechanical properties of the material. Digital image correlation (DIC) was used to measure the strain response of ice-templated ceramic under off-axis loading. …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

Experimental Investigations Of Bio-Syngas Production Using Microwave Pyrolysis Of Uae’S Palm Date Seeds, Mahmmoud Muhammed Syam

Mechanical Engineering Theses

From the start of the industrial revolution, the continued need for energy has been the most crucial issue in human history. An energy crisis started at the beginning of the 1970s when the number of machines, which became an essential part of our life, increased rapidly. Scientists made a huge effort to discover new sources of energy, with ‘biomass’ being one of the main focuses of researchers as a new renewable source of energy. In this thesis, a non conventional method of heating, using microwave power in a pyrolysis process of biomass waste from palm trees (Allig’s date seeds) for …

Modeling And Simulation With Optimal Gear Ratio For A Forward-Looking, Velocity-Driven, Power-Split Hybrid Electric Vehicle, Sonal Babasaheb Kanap

Masters Theses

Increases in vehicle demand and fossil fuel consumption are major contributors to environmental problems, such as air pollution and climate change. This has led to research on alternative, energy-efficient vehicle technologies. Automobile users are now preferring comfortable vehicles with minimal fuel consumption and with more efficient engines. Hybrid cars are becoming common because of their advantage of running cleaner and with better gas mileage. A hybrid car runs on the power of both an electric motor and a gasoline engine. This mechanism helps cut fuel consumption and conserve energy. An additional advantage is a regenerative braking system that helps recharge …

Fatigue Strength Evaluation And Fracture Behavior Of Joined Dual Phase Steel/Aa6061-T6 Aluminum Alloy, Ruben Perez Mora, Celso Eduardo Cruz Gonzalez, Saul Daniel Santillan Gutierrez, Jaime Taha-Tijerina, Benjamin Vargas Arista, Arturo Barba Pingarron

Informatics and Engineering Systems Faculty Publications

The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to determine maximum shear loads, for the single lap shear testing for 5.0 mm overlap length were 2 to 3.5 times higher in comparison to the 12.7 mm overlap length specimens. The results for the strain measurement revealed that higher strain-stress were developed in the 6061-T6 aluminum alloy adherend and in all cases they were lower than the adherends yield strength. Fatigue testing was carried out …

Towards A Pre-Processing Algorithm For Automated Arrhythmia Detection, Sarah Miller

Honors Theses

There are a variety of different wearable fitness/cardiac monitoring devices that are currently used in many people’s day to day life. The primary cardiac function of these devices is to monitor heart rate, however we believe that they could be utilized to detect different forms of arrhythmia. In order to categorize and identify different forms of arrhythmia, we are utilizing published EKG data sets from existing databases as a basis for machine learning. The challenge that comes from the existing data sets is that the format they present the data in does not lend itself to machine learning, which requires …

Training Set Density Estimation For Trajectory Predictions Using Artificial Neural Networks, Zachary Reinke

Masters Theses

Demand on earth orbiting surveillance systems in increasing as more equipment is put into orbit. These systems rely on predictive techniques to periodically track objects. The demand on these systems may be reduced if object trajectory data to develop scalable training sets used for training artificial neural networks (ANNs) to predict trajectories of a dynamic system. These methods use multi-variable statistics to analyze data energy content to provide the ANN with low density, feature-rich, training data. The developed techniques have been shown to increase ANN prediction accuracy while reducing the size of the training set when applied to a linear …

Optical Transportation And Accumulation Of Microparticles By Self-Accelerating Cusp Beams, Weiwei Liu, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Most of the self-accelerating beams have monotonous single-channel bending structures, which greatly limit their applications in many fields such as microscopic imaging and particle manipulation. In this paper, the self-accelerating cusp beams with variable numbers of multichannel bending structures are generated to demonstrate the optical transportation and accumulation of micrometer polystyrene particles. The transportation velocity and optical force profiles of the microparticles moving along the bending channels of cusp beams are analyzed. Parallel particle transportation and particle accumulation manipulation from all the bending channels are further demonstrated. These results will inspire a lot of promising applications for self-accelerating beams especially …

Optimal Energy Management For Forward-Looking Serial-Parallel Hybrid Electric Vehicle Using Rule-Based Control Strategy, Abhijit Bhaskar Jadhav

Masters Theses

In today’s sophisticated era of technology, resolving environmental problems is a matter of grave concern. Developing hybrid electric vehicles is a good step towards environmental preservation, since they use less fuel compared to conventional vehicles because of the combination of electric and mechanical energy. A hybrid electric vehicle reduces dependence on fossil fuels and hence lowers emissions. Specifically, a hybrid powertrain that includes a conventional gasoline engine and a brushless DC motor offers great potential to meet stringent CO₂ regulations and fuel economy requirements. This thesis focuses on the effects of initial state of charge (SOC) stored in Hybrid …

Human-Centered Electric Prosthetic (Help) Hand, Jamie Ferris, Shiyin Lim, Michael Mehta, Evan Misuraca

Interdisciplinary Design Senior Theses

Through a partnership with Indian non-profit Bhagwan Mahaveer Viklang Sahayata Samiti, we designed a functional, robust, and and low cost electrically powered prosthetic hand that communicates with unilateral, transradial, urban Indian amputees through a biointerface. The device uses compliant tendon actuation, a small linear servo, and a wearable garment outfitted with flex sensors to produce a device that, once placed inside a prosthetic glove, is anthropomorphic in both look and feel. The prosthesis was developed such that future groups can design for manufacturing and distribution in India.

Global Estimation Methodology For Wave Adaptation Modular Vessel Dynamics Using A Genetic Algorithm, Marco Alan Schoener

Doctoral Dissertations and Master's Theses

Determining parameters for a system model for marine vessels becomes more difficult as the model is made more complex. Work has been done to determine the equations of motion, but not to fully define how to estimate all of the system parameters. This work utilizes a global optimization methodology for estimating the system parameters using a genetic algorithm. The optimizer uses training data sets created from a set of ship maneuvering standards to minimize the error in the 3 degree-of-freedom equations of motion. The model has been optimized using a “No Surge-Yaw” model (minimal surge coupling) and a “Full” model …

Finite Element Model Validation And Testing Of An Off-Road Vehicle Under Dynamic Loading Conditions, Mackenzie Susan Cunningham

Doctoral Dissertations and Master's Theses

In the vehicle design life cycle, validation tests consume a significant portion of the available development time. With a short, one-year design cycle, the Embry-Riddle Baja Team leverages computer-aided engineering (CAE) tools to simulate critical test cases whose loading conditions can be accurately represented by a series of static loads and constraints. Using these conditions, a Finite Element Model (FEM) can be employed to accurately predict the effects of the loading conditions in the components. During the initial design of the front suspension, one major load case was determined to be the main failure load. However, after validation testing the …

Understanding The Strain Localization And Progressive Damage Growth At The Free-Edge Of Composite Laminates Using Digital Image Correlation, Addis Tessema

Theses and Dissertations

Understanding the mechanics of Fiber Reinforced Composites (FRC) that guide the design and optimization of laminate structures, have attracted numerous researchers. For the last five decades, various analytical and numerical models have been developed to understand the damage and failure mechanisms in FRC. For long, Classical laminate plate theory (CLPT) has majorly been used as a theoretical guide in the design of composite structures. The CLPT framework is developed based on the consideration of an infinitesimal wide plate that depicts a planar stress condition. Thus, as it considers only the planar stresses, the out of plane interlaminar stresses are absent …

Energy Analysis And Orbit Simulation Of Actuating Cubesat Solar Arrays, Justin T. Ehren

Honors Theses

CubeSats are used in space research to explore new technologies and detect data to gain a better understanding of various areas of research and subjects affecting human life. CubeSats rely on a solar array to generate energy from the sun and perform their various functions in space. This research studies the energy capturing potential of various solar array configurations and positioning devices for CubeSats. The location and orientation of a CubeSat is simulated with MATLAB for both geo-synchronous and sunsynchronous orbits. Two degree-of-freedom (DoF) positioning devices are sufficient to continuously adjust the photovoltaic array to face towards the sun. Lower …

Wavelet Transform On Digital Rainbow Hologram Based On Spectral Compression For Quality Enhancement In 3d Display Media, Ucuk Darusalam, Panca Dewi Pamungkasari

Makara Journal of Technology

A digital rainbow hologram (DRH) is a potential next-generation three-dimensional display media for the development of modern and smart electronics devices. It is one of the methods that can support the characteristic whereby a realistic display media occupies the space that the real object would have occupied. Since a rainbow hologram records a large amount of spatial or temporal frequency component from the object that represents the rainbow spectrum, a large amount of information needs to be decoded digitally. In this paper, to reconstruct a DRH, we propose a novel method based on the modulation of red, green, and blue …

Shock Compaction Of Graphene Doped Yttria Stabilized Zirconia: An Experimental And Computational Study, Christopher Rueben Johnson

Master's Theses (2009 -)

Yttria stabilized zirconia (YSZ) is a broadly used ceramic due to its impeccable hardness and thermal stability. Limitations of the material, however, subsist within its fracture toughness. Literature indicates that shock consolidation may enable production of composite YSZ and graphene mixtures with improved fracture toughness and other material properties while maintaining the material’s nanostructure dimensionality. Therefore, investigation of the compaction phenomena at non-equilibrium states will provide informative results to be used in the fabrication of bulk graphene-YSZ composites. Computational molecular dynamics (MD) simulations and impact experiments are conducted to explore and characterize the dynamic response of the YSZ variants. Molecular …

Microfabrication And Characterization Of Freestanding And Integrated Carbon Nanotube Thin Films, Derric Benjamin Syme

Theses and Dissertations

This work chronicles the fabrication of two unique thin films using carbon nanotubes. The first is a carbon film made primarily from vertically grown carbon nanotubes (CNTs) and rolled into lateral alignment. The second is an insulating film created by CNTs as a scaffolding to create a porous silica layer. Each topic represents a different method of utilizing CNTs for thin-film fabrication.Investigation of an entirely carbon thin film, comprised of aligned and laterally oriented carbon nanotubes was performed. The thin film was strengthened by deposition of amorphous carbon for a total thickness of <<> 5 µm. This thickness is thinner than …

A Discovery Of Social Impact Categories For The Sustainable Design Of Engineered Products And Their Consideration By Industry Professionals, Andrew Taylor Pack

Theses and Dissertations

Sustainable design is often practiced and assessed through the consideration of three essential areas: economic sustainability, environmental sustainability, and social sustainability. For even the simplest of products, the complexities of these three areas and their trade-offs cause decision making transparency to be lost in most practical situations. Additionally, the models and tools available to consider social sustainability are severely underdeveloped. This thesis is separated into three parts: 1) a design tool to consider all three aspects of sustainability simultaneously, 2) a literature survey to characterize social impact as it relates to products, and 3) interviews with engineering professionals regarding how …

Analysis Of Distortion Transfer And Generation Through A Fan And A Compressor Using Full-Annulus Unsteady Rans And Harmonic Balance Approaches, Daniel Robert Soderquist

Theses and Dissertations

Understanding distortion transfer and generation through fan and compressor blade rows is able to assist in blade design and performance prediction. Using full annulus unsteady RANS simulations, the effects of distortion as it passes through the rotor of a transonic fan at five radial locations (10%, 30%, 50%, 70%, and 90% span) are analyzed. The inlet distortion profile is a 90-degree sector with a 15% total pressure deficit. Fourier distortion descriptors are used in this study to quantitatively describe distortion transfer and generation. Results are presented and compared for three operating points (near-stall, design, and choke). These results are used …

Mesoscale Modeling Of Shape Memory Alloys By Kinetic Monte Carlo–Finite Element Analysis Methods, Adam David Herron

Theses and Dissertations

A coupled kinetic Monte Carlo – Finite Element Analysis (kMC–FEA) method is developed with a numerical implementation in the Scalable Implementation of Finite Elements at NASA (ScIFEN). This method is presented as a mesoscale model for Shape Memory Alloy (SMA) material systems. The model is based on Transition State Theory and predicts the nonlinear mechanical behavior of the 1st order solid–solid phase transformation between Austenite and Martensite in SMAs. The kMC–FEA modeling method presented in this work builds upon the work of Chen and Schuh [1, 2]. It represents a “bottom-up” approach to materials modeling and could serve as a …

Estimation Of Arterial Wall Parameters Via Model-Based Analysis Of Noninvasively Measured Arterial Pulse Signals, Dan Wang

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation presents a model-based method for estimating arterial wall parameters from noninvasively measured arterial pulse signals via a microfluidic-based tactile sensor. The sensor entails a polydimethylsiloxane (PDMS) microstructure embedded with 5×1 transducer array built on Pyrex/Polyethylene terephthalate (PET) substrate. The arterial pulse causes a time-varying deflection on the top of the PDMS microstructure, which registers as a resistance change by the transducer at the site of the artery.

Owing to the time-harmonic nature of its radial motion, the arterial wall is modeled as a second-order dynamic system. By combining this dynamic model with a hemodynamic model of blood flow, …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Numerical Analysis On Convective Cooling Augmented By Evaporative Heat And Mass Transfer For Thermal Power Plant Application, Sudipta Saha

Theses and Dissertations

This thesis work describes a numerical study on the effect of evaporative cooling on the augmentation of forced convective cooling. In recent years, on-demand phase change boosted cooling has drawn major interest where convective heat transfer is augmented/aided by evaporative heat and mass transport processes. This dual mode (convection and evaporation) cooling method is envisioned to drastically enhance the heat transfer coefficient where conventional convective cooling has already reached its maximum value and furthermore dry cooling is still a desired objective. A multi- dimensional mathematical model has been developed to conduct simulations over a range of operating parameters to obtain …