Mechanical Engineering Commons^™

A Study Of Brain Neuronal And Functional Complexities Estimated Using Multiscale Entropy In Healthy Young Adults, Sreevalsan S. Menon, K. Krishnamurthy

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Brain complexity estimated using sample entropy and multiscale entropy (MSE) has recently gained much attention to compare brain function between diseased or neurologically impaired groups and healthy control groups. Using resting-state functional magnetic resonance imaging (rfMRI) blood oxygen-level dependent (BOLD) signals in a large cohort (n = 967) of healthy young adults, the present study maps neuronal and functional complexities estimated by using MSE of BOLD signals and BOLD phase coherence connectivity, respectively, at various levels of the brain’s organization. The functional complexity explores patterns in a higher dimension than neuronal complexity and may better discern changes in brain functioning. …

Optimization Of Geometry Parameters Of Inkjet-Printed Silver Nanoparticle Traces On Pdms Substrates Using Response Surface Methodology, Jumana Abu-Khalaf, Loiy Al-Ghussain, Ahmad Nadi, Razan Saraireh, Abdulrahman Rabayah, Safwan Altarazi, Ala’Aldeen Al-Halhouli

Mechanical Engineering Graduate Research

Inkjet printing is an emerging technology with key advantages that make it suitable for the fabrication of stretchable circuits. Specifically, this process is cost-effective and less complex compared to conventional fabrication technologies. Inkjet printing has several process and geometry parameters that significantly affect the electromechanical properties of the printed circuits. This study aims to optimize the geometry parameters of inkjet-printed silver nanoparticle traces on plasma-treated polydimethylsiloxane (PDMS) substrates. The optimization process was conducted for two printed shapes, namely straight line and horseshoe patterns. The examined input factors for the straight line traces were: the number of inkjet-printed layers and line …

Estimation Of Gait Kinematics And Kinetics From Inertial Sensor Data Using Optimal Control Of Musculoskeletal Models, Eva Dorschky, Marlies Nitschke, Ann-Kristin Seifer, Antonie J. Van Den Bogert, Bjoern M. Eskofier

Mechanical Engineering Faculty Publications

Inertial sensing enables field studies of human movement and ambulant assessment of patients. However, the challenge is to obtain a comprehensive analysis from low-quality data and sparse measurements. In this paper, we present a method to estimate gait kinematics and kinetics directly from raw inertial sensor data performing a single dynamic optimization. We formulated an optimal control problem to track accelerometer and gyroscope data with a planar musculoskeletal model. In addition, we minimized muscular effort to ensure a unique solution and to prevent the model from tracking noisy measurements too closely. For evaluation, we recorded data of ten subjects walking …

Thermal Management Using Microelectromechanical Systems Bimorph Cantilever Beams, Ronald A. Coutu Jr., Robert S. Lafleur, John P. K. Walton, Laverne A. Starman

AFIT Patents

A cooling structure for a heat source, where the cooling structure includes a beam having a first end and a second end and a length disposed therebetween. The beam is formed at least in part of a first material having a first thermal coefficient of expansion and a second material having a second thermal coefficient of expansion, where the first thermal coefficient of expansion is different from the second thermal coefficient of expansion. The first end of the beam is thermally connected to the heat source, such that heat generated by the heat source is conducted along the length of …

Ligaos Is A Fast Li-Ion Conductor: A First-Principles Prediction, Xueling Lei, Wenjun Wu, Bo Xu, Chuying Ouyang, Kevin Huang

Faculty Publications

Solid Li-ion conducting electrolytes are highly sought for all solid-state Li-batteries, which are considered the next-generation safe batteries. Here a systematic computational study on the intrinsic transport properties of lithium gallium oxysulfide, LiGaOS (S. G. Pmc21), as a potential solid-state Li-ion electrolyte have been reported. The phonon dispersion spectrum analysis indicates that LiGaOS crystal structure is dynamically stable. The energy band structure and density of states calculations suggest that LiGaOS is an insulator with a wide indirect band gap of ∼5.44 eV. The CI-NEB calculations reveal that the “kick-off” collective migration via Li-interstitials is the dominant conduction mechanism …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• American Foundry Society Chapter Established
• AFS Student Chapter Competes in Casting Competition

Effect Of Silica Fume In Concrete On Mechanical Properties And Dynamic Behaviors Under Impact Loading, Shijun Zhao, Qing Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

The effect of silica fume (SF) in concrete on mechanical properties and dynamic behaviors was experimentally studied by split Hopkinson pressure bar (SHPB) device with pulse shaping technique. Three series of concrete with 0, 12%, and 16% SF as a cement replacement by weight were produced firstly. Then the experimental procedure for dynamic tests of concrete specimens with SF under a high loading rate was presented. Considering the mechanical performance and behaviors of the concrete mixtures, those tests were conducted under five different impact velocities. The experimental results clearly show concrete with different levels of SF is a strain-rate sensitive …

Design Of Hydroxyapatite/Magnetite (Hap/Fe3o4) Based Composites Reinforced With Zno And Mgo For Biomedical Applications, D. Katundi, E. Bayraktar, F. Gatamorta, I. Miskioglu

Michigan Tech Publications, Part 1

Hydroxyapatite (HAP-- Ca 10(PO4 )6 (OH)2 ) is a biocompatible and bioactive material that is widely used for biomedical applications, especially in bone replacements. It has good load carrying capacity; however, it lacks antibacterial property. New bio-composites based on bovine hydroxyapatite doped with, magnetite iron oxide (HAP/ Fe3 O4 ) matrix reinforced with ZnO and MgO nanoparticles are proposed for biomedical applications that provide improved antibacterial activity with potential to be used in magnetic therapy. Microwave sintering was used to manufacture the composites. The microstructure evolution in these composites were studied by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy …

Fabrication And Thermal Characterization Of Composite Cu-Cnt Micropillars For Capillary-Driven Phase-Change Cooling Devices, Gerardo Rojo, Siavash Ghanbari, Jeff Darabi

SIUE Faculty Research, Scholarship, and Creative Activity

This paper presents the fabrication, testing, and modeling of an array of composite copper-carbon nanotubes (Cu-CNT) micropillars as a wick structure for potential application in passive phase-change cooling systems. This novel wick structure has a larger spacing at the base of the micropillars to provide a higher liquid permeability and mushroom-like structures on the top surface of the micropillars with a smaller spacing to provide a greater capillary pressure. The composite Cu-CNT micropillars were fabricated by an electrochemical deposition method on a patterned copper template. Cauliflower-like nanostructures were then grown on the top surface of the micropillars using chronoamperometry technique …

Achieving Energy Justice In Low Income Communities: Creating A Community-Driven Program For Residential Energy Savings, Anya Galli Robertson, Kevin Hallinan, Jennifer Hoody

Biennial Conference: The Social Practice of Human Rights

The cost of residential energy the U.S. is unequally distributed, with low income households paying higher rates and spending 16.8% of their income on utility bills compared to 3.5% of all U.S. Residents.[1] Researchers have found that bringing the housing stock up to the efficiency of the median household would reduce excess energy cost by as much as 68%.[2] However, access to opportunities to reduce residential energy consumption and costs such as tax incentives and utility rebate programs tends to be biased toward wealthier, white homeowners. Additionally, low income residents are most likely to be renters, and residence owners have …

Generic Project Plan For A Mobile Robotics System, Jay Anilkumar Joshi

Masters Theses & Specialist Projects

This thesis discussed the mobile land robots for the robotic competitions. The topics discussed in this thesis are robotic systems, mobile land robots, robot competitions, and example of robot designs. Question-answer sections are added to help understand the requirements to build the robot. Examples include three different teams who participated in different robotic competitions to provide a context for robotic competitions. The thesis was divided into the five chapters. The first and second chapters explained the different kind of robotics systems, and opportunities. The focus of the information was the mobile land robots, which was explained under the third chapter, …

The Benchtop Hybrid - Using A Long-Term Design Project To Integrate The Mechanical Engineering Curriculum, Eric Constans, Krishan Bhatia, Jen Kadlowec, Tom Merrill, Hong Zhang, Bonnie Angelone

Henry M. Rowan College of Engineering Departmental Research

This paper describes the use of a large-scale, multi-semester design project as a means of integrating six courses in the mechanical engineering curriculum. The project, a bench-scale hybrid powertrain, is built up - component by component - as students advance through the curriculum. The authors used the project to test two research hypotheses: 1) that a long-term, large-scale design project would increase long-term subject matter retention and 2) that a long-term, large-scale design project would increase students' design and problem-solving skills. The authors found that the design project had no measurable effect on long-term subject matter retention, but did have …

Thermal Refurbishment Status Of The Irish Housing Stock, Ciara Ahern, Brian Norton

Articles

Energy Performance Certificates (EPCs) are issued for buildings constructed, sold or leased across the EU. Using a generalizable methodology this work exploits Ireland’s EPC national dwelling stock database to determine the thermal refurbishment status of Ireland’s housing stock. It is estimated in 2014 that; i) 58% of walls were insulated at a mean overall heat loss coefficient or U-value of 0.66 W/m 2 K, ii) 67% of roofs were insulated at a mean U-value 0.37 W/m 2 K, iii) 97% of windows were double-glazed, and iv) 53% of floors were insulated to a mean U-value of 0.59 W/m 2 K. …

Aging And Rejuvenation During Elastostatic Loading Of Amorphous Alloys, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

Using molecular dynamics simulations, we investigate the effect of uniaxial elastostatic compression on the potential energy, structural relaxation, and mechanical properties of binary glasses. We consider the three-dimensional Kob-Andersen binary mixture, which was initially cooled from the liquid state to the glass phase with a slow rate at zero pressure. The glass was then loaded with a static stress at the annealing temperature during extended time intervals. It is found that the static stress below the yielding point induces large-scale plastic deformation and significant rejuvenation when the annealing temperature is smaller than a fraction of the glass transition temperature. By …

Development Of A Robotized Laser Directed Energy Deposition System And Process Challenges, Meysam Akbari

Mechanical Engineering Research Theses and Dissertations

Metal additive manufacturing (AM) is a disruptive technology, enabling fabrication of complex and near net shaped parts by adding material in a layer-wise fashion. It offers reduced lead production time, decreased buy-to-fly ratio, and repair and remanufacturing of high value components. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical and mold tooling. However, beside tremendous advantages of AM, there are still some challenges that prevent the adoption of this technology into high standard applications. Anisotropy and inhomogeneity in mechanical properties of the as-built parts and existence of pores and lack-of-fusion defects are considered as …

A Novel Fiber Jamming Theory And Experimental Verification, Jared Richard Chafetz

Master's Theses

This thesis developed a novel theory of fiber jamming and experimentally verified it. The theory relates the performance, which is the ratio between the stiff and soft states of a fiber jamming chamber, to three relative design parameters: the ratio of the wall thickness to the membrane inner diameter, the ratio of the fiber diameter to membrane inner diameter, and the number of fibers. These three parameters, when held constant across different chamber sizes, hold the performance constant. To test the theory, three different types of fiber jamming chambers were built in three different sizes. Each chamber was set up …

Graphene-Based Water Desalination Using Atomistic Simulations, Thanh Chinh Nguyen

Mechanical Engineering Research Theses and Dissertations

My research focused on investigating saltwater transport through nanoporous graphene membranes using molecular dynamics (MD) simulations. Particularly, in this dissertation, we focused on pressure-driven flows of salt water through uncharged and charged nanoporous graphene membranes for water desalination applications. In the first study, desalination performance of uncharged single-layer nanoporous graphene membranes was observed based on volumetric flow rate, required pressure drop, and salt rejection efficiency. A functional relationship between the volumetric flow rate, pressure drop, pore diameter, and the dynamic viscosity of saltwater was also examined. In further studies, transport of salt ions through positively and negatively charged single-layer nanoporous …

Extension Of A Penalty Method For Numerically Solving Constrained Multibody Dynamic Problems, Troy Newhart

Mechanical & Aerospace Engineering Theses & Dissertations

Numerical analysis of constrained static and multibody dynamic systems has become an integral part of engineering analysis with the continued improvements in technology and software availability. Many methods currently exist for numerically solving constrained static and dynamic systems. The applicability of a penalty method for constrained static solutions is observed in many academic texts and papers. The appeal for using a penalty method in statics pertains to its ease of implementation, computational suitability, and accuracy. This thesis extends a static penalty method for use with constrained multibody dynamics to observe if the penalty method’s benefits are similar for a dynamics …

A Cfd Study Of Steady Fully Developed Laminar Flow Through A 90-Degree Bend Pipe With A Square Cross-Sectional Area, Subodh Sushant Toraskar

Mechanical & Aerospace Engineering Theses & Dissertations

Fluid flow through a closed curved conduit has always been a topic of extensive research, as it has many practical and industrial applications. The flow is generally characterized by a presence of secondary flow, vortical motions and pressure losses for different flow regimes. These observed irregularities may positively or negatively impact the flow. They are beneficial for cases where mixing of fluids is required, usually observed for multiphase flow regimes or detrimental for cases involving particles in the fluid. There are also instances where a particle-laden fluid transported through the curved pipe was directly related to corrosion- erosion related problems. …

Numerical Modeling Of Shoreline Response To Storm Tides And Sea Level Rise, Akash Sahu

Civil & Environmental Engineering Theses & Dissertations

In this study, an integrated hydrodynamic, wave, and sediment transport modeling approach is developed for predicting the spatiotemporal variation of erosion of a sandy shoreline due to storm surge, wave action, tidal variations, and relative sea level rise (RSLR). The study site is located at the northern most portion of the city of Norfolk, Virginia, and it is of importance to the city, both in terms of tourism and for the protection that it provides for upland properties against storms. The region, in general, experiences the highest rate of RSLR on the U.S. East Coast which should result in high …

Gesture Based Control Of Semi-Autonomous Vehicles, Brian Sanders

Computational Modeling & Simulation Engineering Theses & Dissertations

The objective of this investigation is to explore the use of hand gestures to control semi-autonomous vehicles, such as quadcopters, using realistic, physics based simulations. This involves identifying natural gestures to control basic functions of a vehicle, such as maneuvering and onboard equipment operation, and building simulations using the Unity game engine to investigate preferred use of those gestures. In addition to creating a realistic operating experience, human factors associated with limitations on physical hand motion and information management are also considered in the simulation development process. Testing with external participants using a recreational quadcopter simulation built in Unity was …

Three-Dimensional Rotation Of Paramagnetic And Ferromagnetic Prolate Spheroids In Simple Shear And Uniform Magnetic Field, Christopher A. Sobecki, Yanzhi Zhang, Cheng Wang

Mathematics and Statistics Faculty Research & Creative Works

We examine a time-dependent, three-dimensional rotation of magnetic ellipsoidal particles in a two-dimensional, simple shear flow and a uniform magnetic field. We consider that the particles have paramagnetic and ferromagnetic properties, and we compare their rotational dynamics due to the strengths and directions of the applied uniform magnetic field. We determine the critical magnetic field strength that can pin the particles' rotations. Above the critical field strength, the particles' stable steady angles were determined. In a weak magnetic regime (below the critical field strength), a paramagnetic particle's polar angle will oscillate toward the magnetic field plane while its azimuthal angle …

A Data Mining Methodology For Vehicle Crashworthiness Design, Xianping Du

Doctoral Dissertations and Master's Theses

This study develops a systematic design methodology based on data mining theory for decision-making in the development of crashworthy vehicles. The new data mining methodology allows the exploration of a large crash simulation dataset to discover the underlying relationships among vehicle crash responses and design variables at multiple levels and to derive design rules based on the whole-vehicle safety requirements to make decisions about component-level and subcomponent-level design. The method can resolve a major issue with existing design approaches related to vehicle crashworthiness: that is, limited abilities to explore information from large datasets, which may hamper decision-making in the design …

Quantification Of Material Degradation For Material State Awareness Of Composite Materials., Vahid Tavaf

Theses and Dissertations

The objectives of this research are to develop a comprehensive method to quantify the material degradation of composite materials in the presence of distributed damages and predict the failure in the defected composites using the updated effective material properties. Defects can grow in composites at the macro scale caused by the microscale voids, matrix cracks, fiber breakages starting from manufacturing processes to the high and low cycle fatigue loads, high temperature, and high humidity during operation. Hence, to predict a more realistic failure model, it is necessary to consider the repercussions of degraded materials. The proposed research work is divided …

Meeting 2030 Primary Energy And Economic Growth Goals Mission Impossible, Matthew K. Heun, Paul E. Brockway

University Faculty Publications and Creative Works

To meet climate change mitigation objectives, international institutions have adopted targets aimed at reducing or ending growth of primary energy consumption. Simultaneously, continued economic growth is forecasted to meet human development goals. Together, declining energy consumption and rising gross domestic product (GDP)is called “absolute decoupling.” However, absolute decoupling is unprecedented for the world economy as a whole (since at least 1971). Is absolute decoupling “Mission impossible?” Given the high stakes, we need a clearer understanding of the extent of future energy–GDP decoupling. To gain that understanding, we perform societal exergy analyses using a novel Physical Supply Use Table framework to …

Dynamic Response Modeling Of High-Speed Planing Craft With Enforced Acceleration, Gene Hou, Brain Johnson, Jonathan Degroff, Steven Trenor, Jennifer Michaeli

Mechanical & Aerospace Engineering Faculty Publications

An approach is investigated in this study for structural dynamic analysis of a high-speed planing hull, in which the pointwise acceleration data collected from sea trials are enforced as base excitation. The paper first performed the full boat analysis of an 11-meter high speed craft for a period of one wave impact selected from each of nine seakeeping runs. The sea trial acceleration data collected from 11 accelerometers placed close to the centerline and the keel are enforced as input, while those from 3 accelerometers placed around the pilot cabin are selected for validation. The substructure dynamic analysis of the …

Developing Origami-Based Approaches To Realize Novel Architectures And Behaviors For Deployable Space Arrays, Nathan Alan Pehrson

Theses and Dissertations

Origami-based approaches for the folding of thick materials for specific application to large deployable space arrays is explored in this work. The folding approaches presented utilize strain energy, spatial kinematics, membranes, compliant mechanisms, and or in combination together to fold finite-thickness materials viewed through the lens of origami-based engineering. Novel architectures and behaviors of mechanisms are developed to achieve packaging efficiency, deployment, and self-stiffening. A method for the folding of monolithic thick-sheet materials is developed by incorporating compliant mechanisms into the material itself to strategically add degrees of freedom. The design and characterization of the compliant mechanisms with consideration to …

Effect Of The Physical Micro-Environment On Cell Adhesion And Force Exertion, Mohamad Eftekharjoo

Mechanical & Aerospace Engineering Theses & Dissertations

Physical characteristics of the microenvironment, such as geometry and stiffness, influence cell adhesion and contractile forces. Here, we determined how these physical factors influenced cell force exertion and adhesion in two specific contexts that have broad relevance.

Fibroblasts are cells in connective tissues that interact with a fibrous extracellular matrix (ECM) that have a predominantly one-dimensional (1D) (fibrillar) geometry. However, it has been unclear as to how the 1D nature of the fibrillar ECM influences the forces exerted by fibroblasts. Here, we used fibroblast cells adherent on fibronectin lines on polyacrylamide (PAA) gels of stiffness 13 and 45 kPa to …

Study Of Wire Arc Additive Manufacturing With Aluminum Alloy 2219, Sritam Kumar Dash

Theses and Dissertations

This thesis discusses WAAM (wire arc additive manufacturing) technology using TIG (Tungsten Inert Gas) welding method with aluminum 2219 as the substrate and aluminum 2319 as the filler material. The most important characteristic of this method of manufacturing is very little wastage of material as it does not follow the conventional method of manufacturing where material is removed from a bigger block to finally achieve the desired shape. This method uses a layer by layer approach to build the part. Generally, in additive manufacturing, the production time may vary depending on the type of method used. The material deposition rate …

Wind Farm Layout Optimization With Loads Considerations, Andrew P. J. Stanley, Jennifer King, Andrew Ning

Faculty Publications

The objective of this paper is to improve the annual energy production of a wind farm by optimizing the layout of a wind farm, while considering fatigue loads on turbines. In this paper, the loads are estimated using the edgewise bending moment computed using CCBlade, a steady-state blade element momentum code. The edgewise bending moment is then used to calculate fatigue damage using Miner’s rule. The fatigue damage is used to constrain the layout optimization problem. We show that our method can predict blade root damage with similar trends to damage calculated with other methods, such as a complex, computationally …