Mechanical Engineering Commons^™

Parametric Study Of A Turbofan Engine With An Auxiliary High-Pressure Bypass, Sharanabasaweshwara A. Asundi, Syed Firasat Ali

Mechanical & Aerospace Engineering Faculty Publications

A parametric study of a novel turbofan engine with an auxiliary high-pressure bypass (AHPB) is presented. The underlying motivation for the study was to introduce and explore a configuration of a turbofan engine which could facilitate clean secondary burning of fuel at a higher temperature than conventionally realized. The study was also motivated by the developments in engineering materials for high-temperature applications and the potential utility of these developments. The parametric study is presented in two phases. Phase I presents a schematic of the turbofan engine with AHPB and the mathematics of the performance parameters at various stations. The proposed …

Impact Of Temperature And Screw Speed On Material Meso-Structure And Tensile Strength In Large Area Pellet-Fed Additive Manufacturing, Xavier Jimenez Guzman

Open Access Theses & Dissertations

Evolution in additive manufacturing, specifically in material extrusion, has resulted in large-scale machines capable of extruding thermoplastic-matrix composite materials in higher volumes to fabricate products for large-scale applications. As with small- and medium-scale material extrusion, the properties of the final product often correlate directly with the bevy of print parameters employed. The current research was performed to evaluate the effects of the screw speed and temperature on an ABS 20%wt. carbon fiber thermoplastic processed on a Big Area Additive Manufacturing (BAAM, Cincinnati Inc) machine. Five screw speeds (50, 150, 250, 350 and 400 rpm) and three extruder temperature profiles were …

Small Satellite Development At Utep, Emily Herzog

Open Access Theses & Dissertations

The small satellite industry has seen tremendous growth in recent years. A CubeSat is a particular type of standardized small satellite that follows the CubeSat specifications. These specifications define the structural, testing, and operational requirements of the satellite. This standard facilitates cheaper design, integration, and launch of satellites, allowing smaller organizations to participate in the normally costly area of space exploration.

The University of Texas at El Paso has recognized the opportunity and has begun developing several CubeSats. The two that are the topic of this Thesis are called Orbital Factory II (OFII) and Orbital Factory X (OFX). An on-orbit …

The Influence Of 3d Porous Chitosan-Alginate Biomaterial Scaffold Properties On The Behavior Of Breast Cancer Cells, Minh-Chau N. Le

Honors Undergraduate Theses

The tumor microenvironment plays an important role in regulating cancer cell behavior. The tumor microenvironment describes the cancer cells, and the surrounding endothelial cells, fibroblasts, and mesenchymal stem cells, along with the extracellular matrix (ECM). The tumor microenvironment stiffens as cancer undergoes malignant progression, providing biophysical cues that promote invasive, metastatic cellular behaviors. This project investigated the influence of three dimensional (3D) chitosan-alginate (CA) scaffold stiffness on the morphology, growth, and migration of green fluorescent protein (GFP) – transfected MDA-MB-231 (231-GFP) breast cancer (BCa) cells. The CA scaffolds were produced by the freeze casting method at three concentrations, 2 wt%, …

Rheological Properties Of Two Stainless Steel 316l Powders For Additive Manufacturing, Haijun Gong, Xiaodong Xing, Hengfeng Gu

Manufacturing Engineering: Faculty Publications (2015-2023)

This study measures the rheological properties of two stainless steel 316L powders which are used for the powder-bed-fusion based additive manufacturing process. The purpose is to evaluate the newly acquired powder in comparison with the used and recycled powder, so that both powders can be mixed with each other to supplement the powder usage. The powder rheology properties, such as dynamic property, bulk property, and shear property, are tested and compared. The results and analysis confirm the compatibility of powder mixing.

Planning For Change In The Electric Power Industry: A Primer For Transactive Energy Scenario Development, Joshua Binus

Engineering and Technology Management Faculty Publications and Presentations

The electric power industry and its associated infrastructures (a.k.a. "the grid") are evolving from centrally planned, organized, and operated networks of players, technologies, and resources to systems of systems that are increasingly digitized and distributed in their operation and innovative capacity. Subsequently, strategic planners and technology managers associated with the electric power industry are faced with a range of scenarios to evaluate, including one that considers the emergence of commercialized transactive energy systems in the coming ten-year time horizon. The crafting of a transactive energy scenario can help inform technology innovation and management efforts that benefit consumers, electricity providers, and …

Design And Testing Of A Wind Energy Harnessing System For Forced Convective Drying Of Grain In Low Wind Speed, Warm And Humid Climates, Francis Akumabi Agbali

Theses and Dissertations--Biosystems and Agricultural Engineering

Forced convective drying using a wind turbine mechanically connected to a ventilation fan was hypothesized for low cost and rapid grain drying in developing countries. The idea was tested using an expandable wind turbine blade system with variable pitch, at low wind speeds in a wind tunnel. The design was based on empirical and theoretical models embedded in a graphical user interface (GUI) created to estimate airflow-power requirements for drying ear corn. Output airflow (0.0016 - 0.0052 m³kg^-1s^-1) increased within the study wind speed range (2.0 - 5.5 m/s). System efficiency peak (8.6%) was …

Dust Transportation And Settling Within The Mine Ventilation Network, Anand Kumar

Theses and Dissertations--Mining Engineering

Dust is ubiquitous in underground mine activities. Continuous inhalation of dust could lead to irreversible occupational diseases. Dust particles of size lower than 75.0 µm, also known as float coal dust, can trigger a coal dust explosion following a methane ignition. Ventilation air carries the float coal dust from the point of production to some distance before it’s deposited on the surfaces of underground coal mine. Sources of dust are widely studied, but study of dust transportation has been mainly based on experimental data and simplified models. An understanding of dust transportation in the mine airways is instrumental in …

Quantification Of Myocardial Mechanics In Left Ventricles Under Inotropic Stimulation And In Healthy Right Ventricles Using 3d Dense Cmr, Zhan-Qiu Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

Statistical data from clinical studies indicate that the death rate caused by heart disease has decreased due to an increased use of evidence-based medical therapies. This includes the use of magnetic resonance imaging (MRI), which is one of the most common non-invasive approaches in evidence-based health care research. In the current work, I present 3D Lagrangian strains and torsion in the left ventricle of healthy and isoproterenol-stimulated rats, which were investigated using Displacement ENcoding with Stimulated Echoes (DENSE) cardiac magnetic resonance (CMR) imaging. With the implementation of the 12-segment model, a detailed profile of regional cardiac mechanics was reconstructed for …

Development Of A Muffler Insertion Loss Flow Rig, Jonathan Chen

Theses and Dissertations--Mechanical and Aerospace Engineering

Mufflers and silencers are commonly used to attenuate noise sources such as internal combustion engines and HVAC systems. Typically, these environments contain mean flow that can affect the acoustic properties of the muffler components and may produce flow generated noise. To characterize the muffler performance, common metrics such as insertion and transmission loss and noise reduction are used in industry. Though transmission loss without flow is often measured and is a relatively simple bench top experiment and useful for model validation purposes, mean flow can significantly affect the muffler performance. There are a few existing and commercial transmission loss rigs …

Determination Of Acoustic Radiation Efficiency Via Particle Velocity Sensor With Applications, Steven Conner Campbell

Theses and Dissertations--Mechanical and Aerospace Engineering

Acoustic radiation efficiency is defined as the ratio of sound power radiated to the surface vibration power of a piston with equivalent surface area. It has been shown that the radiation efficiency is maximized and may exceed unity when the structural and acoustic wavelengths are approximately equal. The frequency at which this occurs is called the critical frequency and can be shifted with structural modifications. This has proven to be an effective way to reduce noise. The standard radiation efficiency measurement is comprised of an intensity scan for sound power measurement and accelerometer array for spatially averaged vibration determination. This …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Transforming A Circular Economy Into A Helical Economy For Advancing Sustainable Manufacturing, Ryan T. Bradley

Theses and Dissertations--Mechanical and Aerospace Engineering

The U.N. projects the world population to reach nearly 10 billion people by 2050, which will cause demand for manufactured goods to reach unforeseen levels. In order for us to produce the goods to support an equitable future, the methods in which we manufacture those goods must radically change. The emerging Circular Economy (CE) concept for production systems has promised to drastically increase economic/business value by significantly reducing the world’s resource consumption and negative environmental impacts. However, CE is inherently limited because of its emphasis on recycling and reuse of materials. CE does not address the holistic changes needed across …

Quantification Of Papillary Muscle Motion And Mitral Regurgitation After Myocardial Infarction, Connor R. Ferguson

Theses and Dissertations--Mechanical and Aerospace Engineering

Change in papillary muscle motion as a result of left ventricular (LV) remodeling after posterolateral myocardial infarction is thought to contribute to ischemic mitral regurgitation. A finite element (FE) model of the LV was created from magnetic resonance images acquired immediately before myocardial infarction and 8 weeks later in a cohort of 12 sheep. Severity of mitral regurgitation was rated by two-dimensional echocardiography and regurgitant volume was estimated using MRI. Of the cohort, 6 animals (DC) received hydrogel injection therapy shown to limit ventricular remodeling after myocardial infarction while the control group (MI) received a similar pattern of saline injections. …

A Computational Study Of Patch Implantation And Mitral Valve Mechanics, Dara Singh

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarction (i.e., a heart attack) is the most common heart disease in the United States. Mitral valve regurgitation, or the backflow of blood into the atrium from the left ventricle, is one of the complications associated with myocardial infarction. In this dissertation, a validated model of a sheep heart that has suffered myocardial infarction has been employed to study mitral valve regurgitation. The model was rebuilt with the knowledge of geometrical changes captured with MRI technique and is assigned with anisotropic, inhomogeneous, nearly incompressible and highly non-linear material properties. Patch augmentation was performed on its anterior leaflet, using a …

Hot-Wire Anemometer Measurements Of Atmospheric Surface Layer Turbulence Via Unmanned Aerial Vehicle, Caleb A. Canter

Theses and Dissertations--Mechanical and Aerospace Engineering

An instrumented unmanned aerial vehicle (UAV) was developed and employed to observe the full range of turbulent motions that exist within the inertial subrange of atmospheric surface layer turbulence. The UAV was host to a suite of pressure, temperature, humidity, and wind sensors which provide the necessary data to calculate the variety of turbulent statistics that characterize the flow. Flight experiments were performed with this aircraft, consisting of a large square pattern at an altitude of 100 m above ground level. In order to capture the largest turbulent scales it was necessary to maximize the size of the square pattern. …

Indoor-Wireless Location Techniques And Algorithms Utilizing Uhf Rfid And Ble Technologies, Ann M. Whitney

Theses and Dissertations--Mechanical and Aerospace Engineering

The work presented herein explores the ability of Ultra High Frequency Radio Frequency (UHF RF) devices, specifically (Radio Frequency Identification) RFID passive tags and Bluetooth Low Energy (BLE) to be used as tools to locate items of interest inside a building. Localization Systems based on these technologies are commercially available, but have failed to be widely adopted due to significant drawbacks in the accuracy and reliability of state of the art systems. It is the goal of this work to address that issue by identifying and potentially improving upon localization algorithms.

The work presented here breaks the process of localization …

Trade-Off Balancing For Stable And Sustainable Operating Room Scheduling, Amin Abedini

Theses and Dissertations--Mechanical and Aerospace Engineering

The implementation of the mandatory alternative payment model (APM) guarantees savings for Medicare regardless of participant hospitals ability for reducing spending that shifts the cost minimization burden from insurers onto the hospital administrators. Surgical interventions account for more than 30% and 40% of hospitals total cost and total revenue, respectively, with a cost structure consisting of nearly 56% direct cost, thus, large cost reduction is possible through efficient operation management. However, optimizing operating rooms (ORs) schedules is extraordinarily challenging due to the complexities involved in the process. We present new algorithms and managerial guidelines to address the problem of OR …

Analysis Of Surface Integrity In Machining Of Cfrp Under Different Cooling Conditions, Arjun Nagaraj

Theses and Dissertations--Mechanical and Aerospace Engineering

Carbon Fiber Reinforced Polymers (CFRP) are a class of advanced materials widely used in versatile applications including aerospace and automotive industries due to their exceptional physical and mechanical properties. Owing to the heterogenous nature of the composites, it is often a challenging task to machine them unlike metals. Drilling in particular, the most commonly used process for component assembly is critical especially in the aerospace sector which demands parts of highest quality and surface integrity.

Conventionally, all composites are machined under dry conditions. While there are drawbacks related to dry drilling, for example, poor surface roughness, there is a need …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical and Aerospace Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

The Effects Of System Characteristics, Reference Command, And Command-Following Objectives On Human-In-The-Loop Control Behavior, Seyyedalireza Seyyedmousavi

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans learn to interact with many complex physical systems. For example, humans learn to fly aircraft, operate drones, and drive automobiles. We present results from human-in-the-loop (HITL) experiments, where human subjects interact with dynamic systems while performing command-following tasks multiple times over a one-week period. We use a new subsystem identification (SSID) algorithm to estimate the control strategies (feedforward, feedforward delay, feedback, and feedback delay) that human subjects use during their trials. We use experimental and SSID results to examine the effects of system characteristics (e.g., system zeros, relative degree, system order, phase lag, time delay), reference command, and command-following …

Circulation Dependence Of The Interaction Between A Wing-Tip Vortex And Turbulence, Farshid Najarzadegan

Theses and Dissertations--Mechanical and Aerospace Engineering

Vortices are present in many fluid flows and depending on the context they may be either beneficial or harmful for different systems or processes. Planar particle image velocimetry was used to examine the vortex evolution and its decay under different turbulence intensities and vortex circulation. The vortex decayed faster in the presence of high turbulence intensity. Vortex trajectories were impacted by turbulence intensity and vortex strength. Trajectories with no turbulence intensity had less variation. The vortex wandering amplitude decreased with growth of vortex strength. The vortex decay was confined to the core of the vortex, with the tangential velocity at …

Investigation Of Various Factors Affecting Quantification And Characterization Accuracy Of Nox Measurement At Near Zero Level In A Cvs Sampling Set-Up, Samuel Abimbola Ogunfuye

Graduate Theses, Dissertations, and Problem Reports (ETD)

Accurate measurement of oxides of nitrogen (NOx) concentrations at near-zero levels using the constant volume sampling (CVS) system is a critical consideration in emissions quantification for engine and vehicle research and certification purposes. Various technological efforts and research are being implemented to ensure emissions from automobile and on-road transportation sources tend towards lower concentrations. This development has resulted in NOx concentration measurements to shift towards near-zero and thus, reach the detection limits of traditional measurement approaches and methods. There are several factors that might deter achieving measurement accuracy at this level, as their effect becomes significant at low NOx concentrations. …

Design And Implementation Of An Instantaneous Fuel Mass Flow Measurement System For Use In Verification Of Locomotive Emissions, Adam Wayne James

Graduate Theses, Dissertations, and Problem Reports (ETD)

Located in Altoona, PA, the Juniata Thoroughbred Emissions Research lab has provided emissions testing and research for several locomotive companies such as CSX, Electro Motive Diesel (EMD), and General Electric (GE). The emissions laboratory measures locomotive emissions through partial flow dilution (PFD) sampling for particulate matter (PM) using a Sierra Instruments BG3 and measures raw gaseous emissions using a MEXA 7100D gaseous emission analyzer. Fuel consumption is measured on a gravimetric basis and is used in verification of proportional sampling of exhaust flow. There were two research goals for this study which were (1) verify that the emissions measurement system …

Impact Of Implementing A Dedicated Outdoor Air System In Parallel With A Multi-Zone Variable-Air Volume System On Energy Consumption, Thermal Comfort, And Life Cycle Cost, Khaled Alghamdi

Graduate Theses, Dissertations, and Problem Reports (ETD)

Heating, Ventilating, and Air-Conditioning systems (HVAC) consume more than 40% of energy in commercial buildings, according to the Commercial Building Energy Consumption Survey in 2012. Therefore, efforts to reduce HVAC energy consumption would be significant in coping with energy-related issues. In that context and in order to enhance the indoor air quality without compromising for energy consumption, the concept of Dedicated Outdoor Air systems (DOAS) emerged.

The literature shows that the integration of DOAS with other HVAC systems has been studied widely, yet the impact of integrating DOAS in parallel with multi-zone Variable-Air Volume systems (multi-zone VAV) for an application …

Experimental Measurement Of Dielectric Properties Of Powdery Materials Using A Coaxial Transmission Line, Robert Tempke

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study proposes a standard methodology for coaxial dielectric property measurements of powdery materials (1-10GHz) using a coaxial transmission line. Four powdery materials with dielectric constants ranging from 3.5 to 70 (SiO2, Al2O3, CeO2, and TiO2) were experimentally investigated at varying volume loading fractions in a paraffin mixture. A statistically significant number of paraffin heterogeneous-mixtures was synthesized for all dielectric powders. The dielectric properties of the constitutive materials were determined using appropriate mixture equations. The sensitivity of the equations dielectric prediction to volume loading is discussed with guidance on selecting the best mixing equation. It was determined that low volume …

Investigation Of Flow Field Structures In A Rectangular Channel With A Pin Fin Array, Patrick Tran

Electronic Theses and Dissertations

Pin fin arrays are commonly found in heat exchangers, turbine blades, and electronic heat sinks. Fin arrays are extended surfaces that are used as turbulence promoters by inducing horseshoe vortex (HSV) and von Karman vortex (KV) structures. The horseshoe vortex are primarily studied in the leading edge of the blunt body, whereas the KV are formed in the trailing side. This study presents an experimental investigation of flow field structures and pressure loss on staggered pin fin array in the wake region, where KV are dominate. These flow structures increase the local levels turbulence and generate eddies that promote flow …

Design And Structural Analysis Of Morphing Wings, Nicholas Fernandez

Electronic Theses and Dissertations

Many natural flyers and marine swimmers can morph their wings during a number of unsteady maneuverings. With such wing morphing they are able to control the unsteady aerodynamic forces. A number of man-made flyers, such as unmanned aerial vehicles and micro air vehicles, fly in comparable Reynolds number range, but they are yet to acquire similar morphing capabilities as natural flyers or swimmers. Moreover, the knowledge of fluid structural interaction (FSI) of such morphing wings is not well developed. Hence there is a need to investigate the FSI of morphing wings. In this thesis, a morphing wing was designed and …

Design, Development, And Testing Of A Miniature Fixture For Uniaxial Compression Of Ceramics Coupled With In-Situ Raman Spectrometer, Ryan Jordan

Electronic Theses and Dissertations

This thesis is about the design, development and integration of an in-situ compression stage which interfaces through the Leica optical microscope coupled with a Renishaw InVia micro-Raman spectrometer. This combined compression stage and Raman system will enable structural characterization of ceramics and ceramic composites. The in-situ compression stage incorporates a 440C stainless steel structural components, 6061 aluminum frame, a NEMA 23 stepper motor. Two load screws that allow to apply compressive loads up to 14,137 N, with negligible off axis loading, achieving target stresses of 500 MPa for samples of up to 6.00 mm in diameter. The system will be …

Dynamics Of A Perfectly Premixed Jet Flame Exhibiting Self-Excited High-Frequency, Transverse Thermoacoustic Instabilities, Lucky Tran

Electronic Theses and Dissertations

This work is an investigation of the behavior of a premixed turbulent jet flame in a cylindrical dump combustor. The degeneracy of the simple configuration in this study lends itself for a detailed study of inherent mechanisms of a self-excited thermoacoustic instability in isolation from system coupling effects, enabling detailed numerical simulations to be carried out to supplement experimental findings. Tests were done at a nominal pressure of 8 bar and inlet temperature around 450 ˚C. Self-excited large eddy simulations were also carried out in OpenFOAM, using a b-Ξ flame-wrinkling model to model the combustion process. Eigenfrequency analysis in COMSOL …