Mechanical Engineering Commons^™

Mechanical Behavior Of Three-Dimensional Braided Nickel-Based Superalloys Synthesized Via Pack Cementation, Nicolas Lippitz, Dinc Erdeniz, Keith W. Sharp, David C. Dunand

Mechanical Engineering Faculty Research and Publications

Braided tubes of Ni-based superalloys are fabricated via three-dimensional (3-D) braiding of ductile Ni-20Cr (wt pct) wires followed by post-textile gas-phase alloying with Al and Ti to create, after homogenization and aging, γ/γ′ strengthened lightweight, porous structures. Tensile tests reveal an increase in strength by 100 MPa compared to as-braided Ni-20Cr (wt pct). An interrupted tensile test, combined with X-ray tomographic scans between each step, sheds light on the failure behavior of the braided superalloy tubes.

Cal Poly Rose Float Overheight Mechanism, Ali A. Harake, Breanna H. Tran, Morgan K. Montalvo, Sergio B. Gutierrez

Mechanical Engineering

The Cal Poly Universities jointly build and enter a floral entry, commonly known as a float, into the Pasadena Tournament of Roses Rose Parade. At the end of this parade route, there is a 16’6” bridge all floats must drive under. The scope of our project is to design and build a mechanism roughly described as an “overheight” mechanism, as its function is to raise and lower large heavy structures so the float is able to pass under the bridge. This hydraulic mechanism is powered via the float animation system.

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Students Ace Certified SOLIDWORKS Associate Exam

Numerical Study Of Lateral Migration Of Elliptical Magnetic Microparticles In Microchannels In Uniform Magnetic Fields, Jie Zhang, Cheng Wang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work reports numerical investigation of lateral migration of a paramagnetic microparticle of an elliptic shape in a plane Poiseuille flow of a Newtonian fluid under a uniform magnetic field by direct numerical simulation (DNS). A finite element method (FEM) based on the arbitrary Lagrangian–Eulerian (ALE) approach is used to study the effects of strength and direction of the magnetic field, particle–wall separation distance and particle shape on the lateral migration. The particle is shown to exhibit negligible lateral migration in the absence of a magnetic field. When the magnetic field is applied, the particle migrates laterally. The migration direction …

Manufacturing Of A Carbon Fiber Part With Complex Geometry, Caitlyn Pellemeier, Eric Rodan, Alex King, Nicolas Carlucci

Mechanical Engineering

The purpose of this study is to determine the best method for manufacturing a part with precision tolerances and a small deflection requirement. The desired tolerances include a flatness of 0.002in, parallelism of 0.005in, heat tolerance of 60℃, and a max deflection at the loaded end of the part of 0.28mm. To accomplish this, our team uses carbon fiber as the part material because compared to traditional metals it is stiffer and lighter. Carbon fiber molding processes are explored and narrowed down to Liquid Composite Molding (LCM) and Resin Transfer Molding (RTM). These processes use dry fiber combined with epoxy …

Powder Bed Surface Quality And Particle Size Distribution For Metal Additive Manufacturing And Comparison With Discrete Element Model, Irene Yee

Master's Theses

Metal additive manufacturing (AM) can produce complex parts that were once considered impossible or too costly to fabricate using conventional machining techniques, making AM machines an exceptional tool for rapid prototyping, one-off parts, and labor-intensive geometries. Due to the growing popularity of this technology, especially in the defense and medical industries, more researchers are looking into the physics and mechanics behind the AM process. Many factors and parameters contribute to the overall quality of a part, one of them being the powder bed itself. So far, little investigation has been dedicated to the behavior of the powder in the powder …

Student Shop Access And Inventory Control In The College Of Architecture And Environmental Design Shops, Ryan Raj Mattel, Chris Steven Chen, Kevin Michael Gallagher

Industrial and Manufacturing Engineering

The Cal Poly College of Architecture and Environmental Design shops, directed by David Kempken, give the opportunity for thousands of students to use the “Learn By Doing” philosophy and operate various machinery, tooling, and devices to complete projects inside and outside of the classroom. These students are able to check out tools and machinery to complete these projects on a weekly basis. This report will discuss the complexities and shortcomings of the current database system, FileMaker Pro, that is used for these transactions. The report will furthermore discuss the design and methodology of replacing this system with an improved integrated …

Reducing Same Day Missed Appointments, Lucas Madison, Tyler Moore, Jolani Chun-Moy

Industrial and Manufacturing Engineering

Radiology Associates (RA) is a diagnostic imaging center that offers high-quality, digital medical imaging and interventional radiology services for patients, physicians and healthcare organizations across the Central Coast. They are an ongoing problem that involves a considerable portion of their patients not showing up for their appointments Our project aims to reduce same day missed appointments at Radiology Associates. Radiology Associates currently has a no-show rate of 13.48%. They lose approximately $240 for every same day missed appointment. Our goal was to find new ways to reduce their no-show rate to 8%. Based on our calculations, Radiology Associates could save …

Electroosmotic Flow Of Viscoelastic Fluid In A Nanoslit, Lanju Mei, Hongna Zhang, Hongxia Meng, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

The electroosmotic flow (EOF) of viscoelastic fluid in a long nanoslit is numerically studied to investigate the rheological property effect of Linear Phan-Thien-Tanner (LPTT) fluid on the fully developed EOF. The non-linear Poisson-Nernst-Planck equations governing the electric potential and the ionic concentration distribution within the channel are adopted to take into account the effect of the electrical double layer (EDL), including the EDL overlap. When the EDL is not overlapped, the velocity profiles for both Newtonian and viscoelastic fluids are plug-like and increase sharply near the charged wall. The velocity profile resembles that of pressure-driven flow when the EDL is …

Modeling Of Aggregation And Gelation Of Nanoparticles Using Quadrature Method Of Moments, Elsayed Abdelfatah, Maysam Pournik

Mechanical Engineering Faculty Publications

Applications of Nanotechnology are growing significantly in the petroleum industry such as oil recovery, and well stimulation. In aqueous media, silica nanoparticles aggregate if there is sufficient attractive energy between nanoparticles. Aggregate size distribution evolves as aggregation continues, and once it spans the space, it forms a gel. The objective of this study is to study the aggregation and gelation kinetics in the batch. Population Balance equation (PBE) is used to model the kinetics of aggregation. Quadrature method of moments (QMOM) is used to convert the PBE with continuous distribution of nanoparticle size into a set of moment equations for …

Total Hemispherical Apparent Radiative Properties Of The Infinite V-Groove With Specular Reflection, Rydge B. Mulford, Nathan S. Collins, Michael S. Farnsworth, Matthew R. Jones, Brian D. Iverson

Faculty Publications

Multiple reflections in a cavity geometry augment the emission and absorption of the cavity opening relative to a flat surface in a phenomenon known as the cavity effect. The extent of the cavity effect is quantified using apparent absorptivity and apparent emissivity. Analysis of complicated thermal systems is simplified through application of apparent radiative properities to cavity geometries. The apparent radiative properties of a specularly-reflecting, gray, isothermal V-groove have been derived analytically, but these results have not been validated experimentally or numerically. Additionally, the model for apparent absorptivity of an infinite V-groove subjected to partial illumination in the presence of …

Performance Control Of A Spray Passive Down-Draft Evaporative Cooling System, Daeho Kang, Richard K. Strand

Publications and Research

A spray passive down-draft evaporative cooling system has been regarded as a low-energy cooling system that leads significant energy savings in the cooling of buildings. While the energy saving capability of the system has been proven, the ability to control a comfortable indoor environment is still inadequate due to strong climatic dependency. This study seeks viable solutions to advance the control competence of the system by mitigating critical problems of the system to be a reliable cooling application in the cooling of buildings. It proposes potential control strategies for the system and alternative operations. It develops a control algorithm for …

Toward A Production Ready Fbj Process For Joining Dissimilar Combinations Of Gadp 1180 Steel And Aa 7085-T76, Kevin Alexander Shirley

Theses and Dissertations

Friction Bit Joining (FBJ) is a new technology that can be used to join dissimilar materials together. This ability makes it a good candidate for creating light weight structures for the automotive industry by combining lightweight materials such as aluminum to stronger materials like advanced high-strength steels. The automotive industry and many other industries have great interest in reducing structure weight to increase fuel efficiency. The purpose of this research is to make FBJ of GADP 1180 to AA 7085-T76 a production ready process by (1) better understanding the effects of process parameters, bit design and tool design on joint …

Water Main Break Rates In The Usa And Canada: A Comprehensive Study, Steven Folkman

Mechanical and Aerospace Engineering Faculty Publications

The economic prosperity of modern cities is based on a complex infrastructure network located both above and below ground. A critical component to public health and economic well-being is our drinking water which is brought to the tap through an elaborate network of underground pipe distribution systems. Since most of this infrastructure is underground, it is out of sight and often neglected. Empirical data on water main breaks helps utilities in their repair and replacement decision making processes in order to deliver clean drinking water to their customers at an affordable price. This report documents the survey results of water …

Les Taux De Rupture De Conduites D’Eau Aux États-Unis Et Au Canada : Une Étude Complète, Steven Folkman

Mechanical and Aerospace Engineering Faculty Publications

La prospérité économique des villes modernes est basée sur un réseau d’infrastructures complexe à la fois en surface et sous la terre. Un élément essentiel pour la santé publique et le bien-être économique est notre eau potable, qui est acheminée jusqu’à notre robinet à travers un réseau complexe de conduites de distribution d’eau souterraines. Étant donné que la plus grande partie de cette infrastructure se trouve sous terre, elle est hors de vue et souvent négligée. Disposer de données empiriques sur des ruptures de conduites d’eau aide les services publics avec leurs processus de prises de décision quant aux réparations …

Functionalized Graphene Oxide As Reinforcement In Epoxy Based Nanocomposites, F. V. Ferreira, F. S. Brito, W. Franceschi, E. A. N. Simonetti, L. .S Cividanes, Mircea Chipara, Karen Lozano

Mechanical Engineering Faculty Publications

The effects of amine-modified graphene oxide on dispersion and micro-hardness of epoxy based nanocomposites are reported. Graphene oxide was prepared by the modified Hummers method followed by hexamethylenediamine functionalization. Analysis conducted through Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy-based infrared spectroscopy show that the functionalization process effectively promoted a replacement of oxygen with amine groups while simultaneously creating defects in the graphitic structure. An increase in hardness was observed for the developed nanocomposites.

An Efficient Coal Pyrolysis Model For Detailed Tar Species Vaporization, Jianqing Li, Simcha L. Singer

Mechanical Engineering Faculty Research and Publications

An accurate and computationally efficient model for the vaporization of many tar species during coal particle pyrolysis has been developed. Like previous models, the molecular fragments generated by thermal decomposition are partitioned into liquid metaplast, which remains in the particle, and vapor, which escapes as tar, using a vapor-liquid equilibrium(VLE) sub-model. Multicomponent VLE is formulated as a rate-based process, which results in an ordinary differential equation (ODE) for every species. To reduce the computational expense of solving many ODEs, the model treats tar and metaplast species as a continuous distribution of molecular weight. To improve upon the accuracy of …

Manufacture Of Complex Geometry Component For Advanced Material Stiffness, David Russell Bydalek

Master's Theses

The manufacture, laminate design, and modeling of a part with complex geometry are explored. The ultimate goal of the research is to produce a model that accurately predicts part stiffness. This is validated with experimental results of composite parts, which refine material properties for use in a final prototype part model. The secondary goal of this project is to explore manufacturing methods for improved manufacturability of the complex part. The manufacturing portion of the thesis and feedback into material model has incorporated a senior project team to perform research on manufacturing and create composite part to be used for experimental …

Electric Vehicle Grid Experiments And Analysis, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This project developed a low cost building energy management system (EMS) and conducted vehicle-to-grid (V2G) experiments on a commercial office building. The V2G effort included the installation and operation of a Princeton Power System CA-30 bi-directional power system. These experiments targeted the reduction of utility peak electrical demand for a commercial office building. In each case, total building peak demand was managed through a computer algorithm to limit the charging rate of electric vehicles or used the vehicle's on-board traction battery as a storage device to minimize peak electrical loads.

Symmetric Equations For Evaluating Maximum Torsion Stress Of Rectangular Beams In Compliant Mechanisms, Guimin Chen, Larry L. Howell

Faculty Publications

There are several design equations available for calculating the torsional compliance and the maximum torsion stress of a rectangular cross-section beam, but most depend on the relative magnitude of the two dimensions of the cross-section (i.e., the thickness and the width). After reviewing the available equations, two thickness-to-width ratio independent equations that are symmetric with respect to the two dimensions are obtained for evaluating the maximum torsion stress of rectangular cross-section beams. Based on the resulting equations, outside lamina emergent torsional joints are analyzed and some useful design insights are obtained. These equations, together with the previous work on symmetric …

Distributions Of Pore Sizes And Atomic Densities In Binary Glasses Revealed By Molecular Dynamics Simulations, Nikolai V. Priezjev, Maxim A. Makeev

Mechanical and Materials Engineering Faculty Publications

We report on the results of a molecular dynamics simulation study of porous glassy media, formed in the process of isochoric rapid quenching from a high-temperature liquid state. The transition to a porous solid occurs due to the concurrent processes of phase separation and material solidification. The study is focused on topographies of the model porous structures and their dependence on temperature and average density. To quantify the pore-size distributions, we put forth a scaling relation that provides a satisfactory data collapse in systems with high porosity. We also find that the local density of the solid domains in the …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Resume Boot Camp for Eagle Expo Career Fair

Numerical Simulation Of Uncoiling And Roller Leveling Processes From Steel Coils, Yufei Xiong

LSU Master's Theses

Uncoiling and roller leveling play an important role in pipe forming because it is prerequisite to make products with good quality. Uncoiling and roller leveling are used to reduce undesired characteristics such as imperfections in sheet flatness and residual stress. Considering residual stress in steel coil which has been ignored to date, a simplified coiling process is combined with uncoiling and leveling processes to investigate their effects on residual stress and curvature. The objective of this thesis research focuses particularly on studying the influence of coil diameter, uncoiling direction and leveling settings on residual stress and residual strip curvature after …

Formation Of Two-Way Shape Memory Effect In Niti Alloy Using Pulsed Laser Irradiation, Saidjafarzoda Ilhom, Khomidkhodza Kholikov, Peizhen Li, Dovletgeldi Seyitliyev, Zachary Thomas, Duvall Roberts, Omer San, Haluk E. Karaca, Ali O. Er

Mechanical Engineering Faculty Publications

Shape memory alloys (SMAs) are a unique class of smart materials and they were employed in various applications in engineering, biomedical, and aerospace technologies. Here, we report an advanced, efficient, and low-cost direct imprinting method with low environmental impact to create thermally controllable surface patterns. Patterned microindents were generated on Ni₅₀Ti₅₀ (at. %) SMAs using an Nd:YAG laser with 1064 nm wavelength at 10 Hz. Laser pulses at selected fluences were focused on the NiTi surface and generated pressure pulses of up to a few GPa. Optical microscope images showed that surface patterns with tailorable sizes can …

Microfluidic Technology And Application In Urinal Analysis, Jiwen Xiang

LSU Doctoral Dissertations

Microfluidic technology offers numerous advantages in minimizing and integrating the traditional assays. However, the lack of efficient control components of the microfluidic systems has been hindering the widely commercialization of the technology. The research work in this dissertation focused on the development of effective control components for microfluidic applications.

A linear peristaltic pump was firstly designed, fabricated, and tested for conventional microfluidics by synchronously compressing the microfluidic channel with a miniature cam-follower system in Chapter 2. The miniature cam-follower system and microfluidic chip was prototyped using three-dimensional (3D) printing technology and soft lithography technology. Results from experimental test showed that …

Wetting Properties Of Structured Interfaces Composed Of Surface-Attached Spherical Nanoparticles, Nikolai V. Priezjev, Bishal Bhattarai

Mechanical and Materials Engineering Faculty Publications

The influence of the external pressure and surface energy on the wetting transition at nanotextured interfaces is studied using molecular dynamics and continuum simulations. The surface roughness of the composite interface is introduced via an array of spherical nanoparticles with controlled wettability. We find that in the absence of an external pressure, the liquid interface is flat and its location relative to the solid substrate is determined by the particle size and the local contact angle. With increasing pressure on the liquid film, the interface becomes more curved and the three-phase contact line is displaced along the spherical surface but …

Molecular Simulation Of Steady-State Evaporation And Condensation In The Presence Of A Non-Condensable Gas, Zhi Liang, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Molecular Dynamics Simulations, We Study Evaporation and Condensation of Fluid Ar in the Presence of a Non-Condensable Ne Gas in a Nanochannel. the Evaporation and Condensation Are Driven by the Temperature Difference, ΔTL, between the Evaporating and Condensing Liquid Surfaces. the Steady-State Evaporation and Condensation Fluxes (JMD) Are Also Affected by the Ne Concentration, ΡNe, and the Nanochannel Length. We Find that Across a Wide Range of ΔTL and ΡNe, JMD is in Good Agreement with the Prediction from Stefan's Law and from Schrage Relationships. Furthermore, for ΔTL Less Than ∼20% of the Absolute Average Temperature, We Find that …

Xps Studies Of Lscf Interfaces Afer Cell Testing, Gianfranco Digiuseppe, Venkatesh Boddapati, Hiten Mothikhana

Mechanical Engineering Publications

The motivation of this investigation is to explore the possibility of using the depth profile capability of XPS to study interfaces after SOFC button cell testing. The literature uses XPS to study various cathode materials but has devoted little to the understanding of various cathode interfaces especially after testing. In this work, an SOFC button cell is first tested, and then, the LSCF cathode, barrier layer, and electrolyte are sputtered away to study the behavior of different interfaces. This work has shown that some elements have moved into other layers of the SOFC cell. It is argued that the migration …

Mechanical Properties And Flame Retardancy Of Surface Modified Magnesium Oxysulfate (5mg(Oh)2·Mgso4·3h2o) Whisker For Polypropylene Composites, Eui-Su Kim, Ye Chan Kim, Jungwoo Park, Youngjun Kim, Sung-Hoon Kim, Kwang Jin Kim, Jonghwan Suhr, Youngkwan Lee, Seong Hoon Lee, Dae-Sik Kim, Soo-Hyun Kim, Ju-Ho Yun, In-Kyung Park, Jae-Do Nam

Mechanical Engineering Faculty Research

Magnesium oxysulfate (MOS) whisker is considered as a promising inorganic material recently attracting a great attention for being used as a reinforcing filler for polymer composites due to high aspect ratio and extremely-low bulk density. In this study, the MOS was treated with 3-methacryloyloxypropyl-trimethoxy silane (MPS) via sol-gel condensation reactions, which successfully allowed melt mixing with polypropylene (PP) up to 30 wt% of MOS. The tensile strength at yield and modulus of the MOS/PP composites were substantially increased by 50.8% and 362%, respectively, when compared with the pristine PP. As a novel finding, the flame retardancy of MOS was proved …

A Localized Meshless Technique For Generating 3-D Wind Fields, Darrell W. Pepper, Maria Ramos Gonzalez

Mechanical Engineering Faculty Research

A localized meshless method is used to simulate 3-D atmospheric wind fields for wind energy assessment and emergency response. The meshless (or mesh-free) method with radial basis functions (RBFs) alleviates the need to create a mesh required by finite difference, finite volume, and finite element methods. The method produces a fast solution that converges with high accuracy, establishing 3-D wind estimates over complex terrain. The method does not require discretization of the domain or boundary and removes the need for domain integration. The meshless method converges exponentially for smooth boundary shapes and boundary data, and is insensitive to dimensional constraints. …