Mechanical Engineering Commons^™

Intermittency Effects On The Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah Falih Habeeb Alhamdi

Theses and Dissertations--Mechanical and Aerospace Engineering

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions of external wall-bounded flow.

Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length-scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions, due to the imperfect characterization of the upper bound of the inertial cascade by the integral length-scale. When a length-scale based on Townsend's …

Laminar And Turbulent Study Of Combustion In Stratified Environments Using Laser Based Measurements, Stephen William Grib

Theses and Dissertations--Mechanical and Aerospace Engineering

Practical gas turbine engine combustors create extremely non-uniform flowfields, which are highly stratified making it imperative that similar environments are well understood. Laser diagnostics were utilized in a variety of stratified environments, which led to temperature or chemical composition gradients, to better understand autoignition, extinction, and flame stability behavior. This work ranged from laminar and steady flames to turbulent flame studies in which time resolved measurements were used.

Edge flames, formed in the presence of species stratification, were studied by first developing a simple measurement technique which is capable of estimating an important quantity for edge flames, the advective heat …

Scale Models Of Acoustic Scattering Problems Including Barriers And Sound Absorption, Nan Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

Scale modeling has been commonly used for architectural acoustics but use in other noise control areas is nominal. Acoustic scale modeling theory is first reviewed and then feasibility for small-scale applications, such as is common in the electronics industry, is investigated. Three application cases are used to examine the viability. In the first example, a scale model is used to determine the insertion loss of a rectangular barrier. In the second example, the transmission loss through parallel tubes drilled through a cylinder is measured and results are compared to a 2.85 times scale model with good agreement. The third example …

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Numerical And Experimental Techniques For Assessing The Acoustic Performance Of Duct Systems Above The Plane Wave Cutoff Frequency, Kangping Ruan

Theses and Dissertations--Mechanical and Aerospace Engineering

This research deals with determining the acoustic attenuation of heating, ventilation, and air conditioning (HVAC) ductwork. A finite element approach was developed for calculating insertion loss and breakout transmission loss. Procedures for simulating the source and receiving rooms were developed and the effect of structureborne flanking was included. Simulation results have been compared with measurements from the literature and the agreement is very good. With a good model in place, the work was extended in three ways. 1) Since measurements on full-scale equipment are difficult, scale modeling rules were developed and validated. 2) Two different numerical approaches were developed for …

Characterization Of Methane-Air Diffusion Flames For Flame Synthesis Application Through Optical Diagnostics, Zhaojin Diao

Theses and Dissertations--Mechanical and Aerospace Engineering

Flame synthesis is a growing field of research aiming at forming new materials and coatings through injection of seed materials into a flame. Accurate prediction of the thermal structure of these flames requires detailed information on the radiative properties and a thorough understanding of the governing combustion processes. The objective of this work is to establish a basic optical diagnostic characterization of different methane-air diffusion flames of different complexity. The basic principles are developed and demonstrated at a rotational symmetric co-flow burner and finally applied to a burner consisting of six clustered microflames which is designed for future flame synthesis …

Bayesian-Integrated System Dynamics Modelling For Production Line Risk Assessment, Sudhir Punyamurthula

Theses and Dissertations--Mechanical and Aerospace Engineering

Companies, across the globe are concerned with risks that impair their ability to produce quality products at a low cost and deliver them to customers on time. Risk assessment, comprising of both external and internal elements, prepares companies to identify and manage the risks affecting them. Although both external/supply chain and internal/production line risk assessments are necessary, internal risk assessment is often ignored. Internal risk assessment helps companies recognize vulnerable sections of production operations and provide opportunities for risk mitigation.

In this research, a novel production line risk assessment methodology is proposed. Traditional simulation techniques fail to capture the complex …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Multiphase Interaction In Low Density Volumetric Charring Ablators, Ali D. Omidy

Theses and Dissertations--Mechanical and Aerospace Engineering

The present thesis provides a description of historical and current modeling methods with recent discoveries within the ablation community. Several historical assumptions are challenged, namely the presence of water in Thermal Protection System (TPS) materials, presence of coking in TPS materials, non-uniform elemental production during pyrolysis reactions, and boundary layer gases, more specifically oxygen, interactions with the charred carbon interface.

The first topic assess the potential effect that water has when present within the ablator by examining the temperature prole histories of the recent flight case Mars Science Laboratory. The next topic uses experimental data to consider the instantaneous gas …

Attitude Control On So(3) With Piecewise Sinusoids, Shaoqian Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses rigid body attitude control with piecewise sinusoidal signals. We consider rigid-body attitude kinematics on SO(3) with a class of sinusoidal inputs. We present a new closed-form solution of the rotation matrix kinematics. The solution is analyzed and used to prove controllability. We then present kinematic-level orientation-feedback controllers for setpoint tracking and command following.

Next, we extend the sinusoidal kinematic-level control to the dynamic level. As a representative dynamic system, we consider a CubeSat with vibrating momentum actuators that are driven by small $\epsilon$-amplitude piecewise sinusoidal internal torques. The CubeSat kinetics are derived using Newton-Euler's equations of motion. …

Discrete-Time Adaptive Control Algorithms For Rejection Of Sinusoidal Disturbances, Mohammadreza Kamaldar

Theses and Dissertations--Mechanical and Aerospace Engineering

We present new adaptive control algorithms that address the problem of rejecting sinusoids with known frequencies that act on an unknown asymptotically stable linear time-invariant system. To achieve asymptotic disturbance rejection, adaptive control algorithms of this dissertation rely on limited or no system model information. These algorithms are developed in discrete time, meaning that the control computations use sampled-data measurements. We demonstrate the effectiveness of algorithms via analysis, numerical simulations, and experimental testings. We also present extensions to these algorithms that address systems with decentralized control architecture and systems subject to disturbances with unknown frequencies.

Comparison Of Emissions Measurement Between A Sensor-Based Compact Emissions Meter And A Standard Pems, Jordan Matthew Leatherman

Graduate Theses, Dissertations, and Problem Reports (ETD)

The emissions produced by diesel engines are detrimental to human health, and the environment. To reduce these harmful emissions, engine manufacturers have used exhaust after treatment systems. The main objective of these after-treatment systems is to reduce exhaust emissions with minimal impact on an engines performance. The increase in emission regulations resulted in the need for a portable device to measure emissions. Portable emissions measurement systems (PEMS) are used to ensure engines comply with regulations in the real world. Although these systems are portable and can be installed on a vehicle they are bulky, expensive and time consuming to install. …

Investigation Of Combustion Characteristics Of A Heavy-Duty Diesel Engine Retrofitted To Natural Gas Spark Ignition Operation, Jinlong Liu

Graduate Theses, Dissertations, and Problem Reports (ETD)

The conversion of existing diesel engines to natural-gas spark ignition operation by adding a gas injector in the intake manifold for fuel delivery and replacing the diesel fuel injector with a spark plug to initiate and control the combustion process can reduce U.S. dependence on petroleum imports and curtail engine-out emissions. As the conventional diesel combustion chamber (i.e., flat head and bowl-in-piston) creates high turbulence, the engine can operate leaner, which would increase its efficiency and reduce emissions. However, natural gas combustion in such retrofitted engines presents differences compared to that in conventional spark ignited engines. Subsequently, the main goal …

The Nakahara Effect And Its Influence On Solution-Based 3d Printed Films, Daryl Kwakye-Ackah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Motivated by the Nakahara Effect, the influence of altering printing parameters on fragmentation mechanism(s) of directly written titanium dioxide(TiO₂) films is investigated. The Nakahara effect states that a long lasting memory can be introduced into a colloidal system prior to drying, affecting the type of crack pattern formed due to externally applied forces. TiO₂ has important applications due to its interesting semiconducting properties, tunable band gap, photocatalytic properties, biocompatibility, and relative abundance. This is the reason it is used in this project as a model printing ink system.

In this research, two deposition methods (i.e. direct-ink writing …

Fluid Dynamics Modeling And Sound Analysis Of A Bileaflet Mechanical Heart Valve, Fardin Khalili

Electronic Theses and Dissertations

Cardiovascular disease (CVD) is one of the main causes of death in the world. Some CVD involve severe heart valve disease that require valve replacement. There are more than 300,000 heart valves implanted worldwide, and about 85,000 heart valve replacements in the US. Approximately half of these valves are mechanical. Artificial valves may dysfunction leading to adverse hemodynamic conditions. Understanding the normal and abnormal valve function is important as it help improve valve designs. Modeling of heart valve hemodynamics using computational fluid dynamics (CFD) provides a comprehensive analysis of flow, which can potentially help explain clinical observations and support therapeutic …

Biomechanical Models Of Human Upper And Tracheal Airway Functionality, Don Nadun Kuruppumullage

Electronic Theses and Dissertations

The respiratory tract, in other words, the airway, is the primary airflow path for several physiological activities such as coughing, breathing, and sneezing. Diseases can impact airway functionality through various means including cancer of the head and neck, Neurological disorders such as Parkinson's disease, and sleep disorders and all of which are considered in this study. In this dissertation, numerical modeling techniques were used to simulate three distinct airway diseases: a weak cough leading to aspiration, upper airway patency in obstructive sleep apnea, and tongue cancer in swallow disorders. The work described in this dissertation, therefore, divided into three biomechanical …

Characterization Of Fast Flames For Turbulence-Induced Deflagration To Detonation Transition, Jessica Chambers

Electronic Theses and Dissertations

One of the fundamental mechanisms for detonation initiation is turbulence driven deflagration to detonation transition (TDDT). The research experimentally explores the propagation dynamics demonstrated by fast deflagrated flames interacting with highly turbulent reactants. Fast flames produce extremely high turbulent flame speeds values, increased levels of compressibility and develop a runaway mechanism that leads to TDDT. The flame structural dynamics and reacting flow field are characterized using simultaneous high-speed particle image velocimetry, chemiluminescence, and Schlieren measurements. The investigation classifies the fast flame propagation modes at various regimes. The study further examines the conditions for a turbulent fast flame at the boundary …

A Study On The Plasticity And Fracture Of Aisi 4340 Steel Under Different Loading Conditions Considering Heat Treatment And Micromechanics, Sami Ghazali

Electronic Theses and Dissertations

Accurate predictions of material strength under different loading conditions with large plastic deformation and ductile fracture are of great importance. This dissertation aims to develop an essential understanding of ductile fracture of AISI 4340 steel alloy using both empirical and micromechanics based models. For this purpose, 29 specimens of different geometries with different heat-treatments were designed to investigate the effects of stress states. These specimens are: (a) 13 round bars with different notches (axial symmetric tension); (b) 13 flat grooved specimens with different grooves; (c) 3 small round cylinders. Mechanical tests up to fracture were conducted on these specimens to …

Energy-Optimal Guidance Of An Auv Under Flow Uncertainty And Fluid-Particle Interaction, Demuni Singith De Zoysa Abeysiriwardena

Electronic Theses and Dissertations

The work presented gives an energy-optimal solution to the guidance problem of an AUV. The presented guidance methods are for lower level control of AUV paths, facilitating existing global planning methods to be carried out comparatively more efficiently. The underlying concept is to use the energy of fluid flow fields the AUVs are navigating to extend the duration of missions. This allows gathering of comparatively more data with higher spatio-temporal resolution. The problem is formulated for a generalized two dimensional uniform flow field given a fixed final time and free end states. This allows the AUVs to navigate to certain …

Mechanisms Of Flame Extinction For Bluff Body Stabilized Flames With Influences Of Pressure Gradient Tailoring, Anthony Morales

Electronic Theses and Dissertations

Flame extinction continues to hinder the performance of combustion technologies used in propulsion systems and power generating turbomachinery. Within these applications, there is a crucial need to improve energy output while minimizing harmful environmental impacts. Lean combustion helps attain these goals by minimizing fuel costs and reducing NOx emissions. However, operating at lean conditions increases the likelihood of flame extinction; the flame becomes more susceptible to hydrodynamic instabilities which can induce global blowout and termination of the combustion process. The work in this thesis is focused on identifying the mechanisms of flame extinction and controlling these mechanisms via pressure gradient …

Flutter Stability Of Shrouded Turbomachinery Cascades With Nonlinear Frictional Damping, Alex Torkaman

Electronic Theses and Dissertations

Prediction of flutter in shrouded turbomachinery cascades is difficult due to i) coupling of aerodynamic drivers and structural dynamics of the cascade through shrouds, and ii) presence of nonlinear dry friction damping as a result of relative motion between adjacent shrouds. An analytical framework is developed in this dissertation to determine flutter stability of shrouded cascades with consideration of friction damping. This framework is an extension to the well-established energy method, and it includes all contributing factors affecting stability of the cascade such as aerodynamic excitation and the stabilizing effects of dry friction damping caused by nonlinear contact forces between …

A Localized Blended Rbf Collocation Method For Effective Shock Capturing, Michael Harris

Electronic Theses and Dissertations

Solving partial differential equations (PDEs) can require numerical methods, especially for non-linear problems and complex geometry. Common numerical methods used today are the finite difference method (FDM), finite element method (FEM) and the finite volume method (FVM). These methods require a mesh or grid before a solution is attempted. Developing the mesh can require expensive preprocessing time and the quality of the mesh can have major effects on the solution. In recent years, meshless methods have become a research interest due to the simplicity of using scattered data points. Many types of meshless methods exist stemming from the spectral or …

Investigation Of Oxy-Fuel Combustion Behind Reflected Shockwaves, Owen Pryor

Electronic Theses and Dissertations

Supercritical carbon dioxide has brought about new questions on the chemical kinetics of several small hydrocarbon fuels and the effects of carbon dioxide as the primary diluent on the different fuels. This report presents work on the ignition delay times and several species time-histories of methane, ethylene and syngas over a range of conditions. All experiments were conducted behind reflected shock waves using two different shock tubes. The ignition delay times were measured using a GaP photodetector to measure the emission of light. The species time-histories were measured using single laser spectroscopy. The effect of CO2 as a diluent on …

Bio-Inspired Visual Servo Control Of A Picking Mechanism In An Agricultural Ground Robot, Sinem Gozde Defterli

Electronic Theses and Dissertations

For a recently constructed disease detection agricultural ground robot, the segregation of unhealthy leaves from strawberry plants is a major task of the robot's manipulation subsystem in field operations. In this dissertation, the motion planning of a custom-designed picking mechanism in the ground robot's subsystem is studied in two sections. First, a set of analytical, suboptimal semi-analytical and numerical algorithms are studied to solve the inverse kinematics problem of the handling mechanism in firm circumstances. These premeditated approaches are built on the computation of the joint variables by an identified 3D position data of the target leaf only. The outcomes …

Investigation Of A Self-Powered Fontan Concept Using A Multiscale Computational Fluid-Structure Interaction Model, Kyle Beggs

Electronic Theses and Dissertations

Congenital Heart Disease (CHD) occurs in about 1\% (40,000) of newborn babies each year in the United States alone. About 10.9\% (960) of whom suffer from Hypoplastic Left Heart Syndrome (HLHS) - a subset of CHD where children are born with a single-ventricle (SV). A series of three surgeries are carried out to correct HLHS culminating in the Fontan procedure where venous flow returns passively to the lungs. The current configuration for the Fontan results in elevated Central Venous Pressure (CVP), inadequate ventricular preload, and elevated Pulmonary Vascular Resistance (PVR) leading to a barrage of disease. To alleviate these complications, …

Electrospray And Superlens Effect Of Microdroplets For Laser-Assisted Nanomanufacturing, Eduardo Castillo Orozco

Electronic Theses and Dissertations

Nanoparticles of various materials are known to exhibit excellent mechanical, chemical, electrical, and optical properties. However, it is difficult to deposit and transform nanoparticles into large two-dimensional and three-dimensional structures, such as thin films and discrete arrays. Electrospray technology and laser heating enable the deposition of these nanoparticles through the dual role of microdroplets as nanoparticle carriers and superlenses. The main goals of this dissertation are to delineate the electrospray modes, to achieve subwavelength focusing, and to enable a process for the deposition of nanoparticles into microlayers and discrete nanodots (a nanodot is a cluster of nanoparticles) on rigid and …

Detailed Understanding Of Flow, Heat Transfer, And Pressure Drop Behavior In A Square Channel With 45 Deg Ribs, Lumaya Ahmed

Electronic Theses and Dissertations

Internal Duct Cooling (IDC) with rib turbulators is one of the common cooling techniques applied inside the turbine airfoils. It is very important for the gas turbine industry to design and develop an optimized cooling channel that maximizes the amount of heat removed, while simultaneously minimizing the pressure drop for a target overall cooling effectiveness. Angled ribs perform superior to the transverse ribs due to additional secondary flow associated with them. However, they result in a highly non-homogenous heat transfer distribution, which is a manifestation of the complex, turbulent flow field inside the channel. It is very important to comprehend …

Brain Stethoscope: A Non-Invasive Method For Monitoring Intracranial Pressure, Md Khurshidul Azad

Electronic Theses and Dissertations

Monitoring intracranial pressure (ICP) is important for patients with increased intracranial pressure. Invasive methods of ICP monitoring include lumbar puncture manometry, which requires high precision, is costly, and can lead to complications. Non-invasive monitoring of ICP using tympanic membrane pulse (TMp) measurement can provide an alternative monitoring method that avoids such complications. In the current study, a piezo based sensor was designed, constructed and used to acquire TMp signals. The results showed that tympanic membrane waveform changed in morphology and amplitude with increased ICP, which was induced by changing subject position using a tilt table. In addition, the results suggest …