Mechanical Engineering Commons^™

Heat Removal Analysis Using Ntu Microscopic Theory And Experimental Fluid Testing Of Radaitors, Pumps And Fans For The Thermal Management System Of Formula Sae Electric Racecar, Shahzad Shahrukh Bulsara

Mechanical and Aerospace Engineering Theses - Archive

Formula SAE at UT Arlington has always been building well engineered race cars, further being one of the top teams in The United States. However, an electric race car being first in the fleet, cooling of electric motors played a vital role. The thermal system being significantly different from combustion cars, consists of a lower heat application. It is always favorable to maintain electronics as close to ambient temperature as compared to its counter hydro-mechanical engines. To attain the objective, a complete thermal & fluid analysis was carried out using the NTU method/ microscopic theory and experimental results associated towards …

Zrb2-Sic Based Ultra High Temperature Ceramic Composites: Mechanical Performance And Measurement And Design Of Thermal Residual Stresses For Hypersonic Vehicle Applications, Richard Stadelmann

Electronic Theses and Dissertations

Ultra-high temperature ceramics (UHTCs), such as ZrB2-based ceramic composites, have been identified as next generation candidate materials for leading edges and nose cones in hypersonic air breathing vehicles. Mechanical performance of ceramic composites play an important role in the ultra-high temperature applications, therefore SiC is added to ZrB2 as a strengthening phase to enhance its mechanical performance. The high melting temperatures of both ZrB2 and SiC, as well as the ability of SiC to form SiO2 refractory oxide layers upon oxidation make ZrB2-SiC ceramics very suitable for aerospace applications. Thermal residual stresses appearing during processing are unavoidable in sintered ZrB2-SiC …

Experimental And Numerical Study Of Endwall Film Cooling, Srikrishna Mahadevan

Electronic Theses and Dissertations

This research work investigates the thermal performance of a film-cooled gas turbine endwall under two different mainstream flow conditions. In the first part of the research investigation, the effect of unsteady passing wakes on a film-cooled pitchwise-curved surface (representing an endwall without airfoils) was experimentally studied for heat transfer characteristics on a time-averaged basis. The temperature sensitive paint technique was used to obtain the local temperatures on the test surface. The required heat flux input was provided using foil heaters. Discrete film injection was implemented on the test surface using cylindrical holes with a streamwise inclination angle of 35? and …

Thermodynamic Analysis And Optimization Of Supercritical Carbon Dioxide Brayton Cycles, Mahmood Mohagheghi

Electronic Theses and Dissertations

The power generation industry is facing new challenging issues regarding accelerating growth of electricity demand, fuel cost and environmental pollution. These challenges accompanied by concerns of energy resources becoming scarce necessitate searching for sustainable and economically competitive solutions to supply the future electricity demand. To this end, supercritical carbon dioxide (S-CO2) Brayton cycles present great promise particularly in high temperature concentrated solar power (CSP) and waste heat recovery (WHR) applications. With this regard, this dissertation is intended to perform thorough thermodynamic analyses and optimization of S-CO2 Brayton cycles for both of these applications. A modeling tool has been developed, which …

Inverse-Consistent Determination Of Young's Modulus Of Human Lung, Behnaz Seyfi Noferest

Electronic Theses and Dissertations

Human lung undergoes respiration-induced deformation due to sequential inhalation and exhalation. Accurate determination of lung deformation is crucial for tumor localization and targeted radiotherapy in patients with lung cancer. Numerical modeling of human lung dynamics based on underlying physics and physiology enables simulation and virtual visualization of lung deformation. Dynamical modeling is numerically complicated by the lack of information on lung elastic behavior, structural heterogeneity as well as boundary constrains. This study integrates physics-based modeling and image-based data acquisition to develop the patient-specific biomechanical model and consequently establish the first consistent Young's modulus (YM) of human lung. This dissertation has …

A Stroke Of Shear Genius: The Development Of The Blade Bandit, Abdulrahman Hamid

Honors Theses

This thesis will document and analyze the experience of two members of the Shear Genius team, Mr. Abdulrahman Hamid and Mr. Colin Wattigney, as they worked to complete the CME Senior Capstone Project. This team, under the leadership of CEO Ethan Veazey, developed the Blade Bandit, a lawn mower blade sharpening system conceptualized by Mr. Jacob Moorhead. Ms. Kristen Gaddis, Mr. Nick Rocco, and Ms. Allie Winters were also members of Shear Genius. The team members had educational backgrounds in the realms of engineering, business and accountancy. The combination of these disciplines allowed for the simulation of a real business …

Thermodynamic Grain Size Stabilization Models: An Overview, Mostafa Saber, Carl C. Koch, Ronald O. Scattergood

Mechanical and Materials Engineering Faculty Publications and Presentations

Grain boundaries in a nanocrystalline microstructure produce an increase in the excess free energy of the system. Grain growth is a consequence of the thermodynamic driving force reducing this excess. Thermodynamic stabilization is an approach based on eliminating the driving force by suitable alloy additions that can produce a metastable equilibrium state at the nanoscale grain size, as opposed to kinetic stabilization where the grain growth mobility is restricted by pinning and/or drag mechanisms. The present paper reviews and compares various models proposed for thermodynamic stabilization.

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Evan Foreman, Dylan Irvine, Aaron Jackson, Christopher Brandon Remington, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

Analysis Of Thin-Walled Cylindrical Composite Shell Structures Subject To Axial And Bending Loads: Concept Development, Analytical Modeling And Experimental Verification, Sthanu Mahadev

Mechanical and Aerospace Engineering Dissertations - Archive

Several studies have focused on the modeling and response characterization of composite structural members, with particular emphasis on thin-walled cylindrical composite shells. This class of shell configurations is explored to determine their mechanical response in primary aerospace structural members. The present work is focused on formulating a modified composite shell theory prognosis methodology for investigating the structural response of thin-walled cylindrical shell type composite configurations under axial and bending loads, respectively. The prime motivation to develop this theory arises from its capability to generate simple yet accurate closed-form analytical results that can efficiently charecterize cylindrical composite shell constructions. This work …

Design Of Next Generation Antenna Mounts In Telecommunication Towers With Low Effective Projected Area, Ruben Gregory Puthota Dominic Savio

Mechanical and Aerospace Engineering Theses - Archive

Design of new antenna mount with low effective projected area (EPA) and high load carrying capacity for telecommunication towers is the purpose of this thesis. The main aim is to reduce the EPA of the mount against the wind pressure direction at the desired elevation from ground by reducing the mount frame structure parts compared to the previous mount designs used in the market. The model in itself has to withstand its dead weight, operator’s weight along with five antenna-radio units. The new model has been designed with a single horizontal frame and four supporting structure for EPA reduction and …

Characterization Of Flapping Wing Aerodynamics And Flight Dynamics Analysis Using Computational Methods, Alok Ashok Rege

Mechanical and Aerospace Engineering Dissertations - Archive

Insect flight comes with a lot of intricacies that cannot be explained by conventional aerodynamics. Even with their small-size, insects have the ability to generate the required aerodynamic forces using high frequency flapping motion of their wings to perform different maneuvers. The maneuverability obtained by these flyers using flapping motion belies the classical aerodynamics theory and calls for a new approach to study this highly unsteady aerodynamics. Research is on to find new ways to realize the flight capabilities of these insects and engineer a micro-flyer which would have various applications, ranging from autonomous pollination of crop fields and oil …

Comprehensive Design Analysis Of Thick Fr-4 Qfn Assemblies For Enhanced Board Level Reliability, Abhishek Nitin Deshpande

Mechanical and Aerospace Engineering Theses - Archive

Quad Flat No-lead package (QFN) is one of the most cutting-edge technologies emerged in the market, exhibiting high performance and efficiency with unparalleled cost effectiveness. QFN, a leadless package, is an ideal choice for applications where size, weight thermal and electrical characteristics are critical, particularly in mobile and handheld devices. Applications like automotive, defense and high current circuits require the package to be mounted on thick printed circuit boards (PCB). But using thick PCBs (>3mm) is detrimental to the package reliability. The motivation of this work is to understand the effect of several package parameters affecting reliability and optimize …

Incorporating Dynamic Flame Behavior Into The Scaling Laws Of Wildland Fire Spread, Brittany A. Adam

Theses and Dissertations--Mechanical and Aerospace Engineering

A challenge for fire researchers is obtaining data from those fires that are most dangerous and costly. While it is feasible to instrument test beds, test plots, and small prescribed burns for research, it is uncommon to successfully instrument an active wildland fire. With a focus on very specific facets of wildland fire, researchers have created many unique models utilizing matchsticks, cardboard, liquid fuel, excelsior, plywood, live fuels, dead fuels, and wood cribs of different packing densities. Such scale models, however, only serve as valid substitutes for the full-scale system when all functional relations of the scale model are made …

Effect Of Heating And Ionization Of Four Atomizing Gases On The Spray Characteristics Of A High Volume Low Pressure Spray Atomizer, Anthony V. Adornato

Theses and Dissertations--Mechanical and Aerospace Engineering

The disintegration of a liquid jet emerging from a nozzle by a high speed gas stream has been under investigation of several decades. A result of the liquid jet disintegration is droplet formation. This process is referred to as atomization. Industrial applications use atomization as a method for applying coatings to substrates. It has been reported that the use of other atomizing gases instead of compressed plant air will positively affect paint droplet size distributions, spray patterns and finish qualities; furthermore, the ionization and heating of the atomizing gas was reported to positively affect finish qualities. Although ionization techniques have …

Cfd Modeling Of Multiphase Counter-Current Flow In Packed Bed Reactor For Carbon Capture, Li Yang

Theses and Dissertations--Mechanical and Aerospace Engineering

Packed bed reactors with counter-current, gas-liquid flows have been considered to be applicable in CO₂ capture systems for post-combustion processing from fossil-fueled power production units. However, the hydrodynamics within the packing used in these reactors under counter-current flow has not been assessed to provide insight into design and operational parameters that may impact reactor and reaction efficiencies. Hence, experimental testing of a laboratory-scale spherical ball, packed bed with two-phase flow was accomplished and then a meso-scale 3D CFD model was developed to numerically simulate the conditions and outcomes of the experimental tests. Also, the hydrodynamics of two-phase flow in …

Effects Of Magnetic Field On The Shape Memory Behavior Of Single And Polycrystalline Magnetic Shape Memory Alloys, Ali S. Turabi

Theses and Dissertations--Mechanical and Aerospace Engineering

Magnetic Shape Memory Alloys (MSMAs) have the unique ability to change their shape within a magnetic field, or in the presence of stress and a change in temperature. MSMAs have been widely investigated in the past decade due to their ability to demonstrate large magnetic field induced strain and higher frequency response than conventional shape memory alloys (SMAs). NiMn-based alloys are the workhorse of metamagnetic shape memory alloys since they are able to exhibit magnetic field induced phase transformation. In these alloys, martensite and austenite phases have different magnetization behavior, such as the parent phase can be ferromagnetic and martensite …

An Experimental Method Of Measuring Spectral, Directional Emissivity Of Various Materials And Joule Heating, Robert Bickel

Theses and Dissertations--Mechanical and Aerospace Engineering

Emissivity is an important parameter in calculating radiative cooling of a surface. In experiments at the NASA Ames hypervelocity ballistic range, one of the main errors indicated in temperature measurements is the uncertainty of emissivity for the materials under investigation. This thesis offers a method for measuring emissivity of materials at elevated temperatures at the University of Kentucky. A test specimen which consists of different sample materials under investigation and a blackbody cavity was heated in a furnace to an isothermal condition at known temperature. The emitted thermal radiation was measured and the comparison of sample and blackbody radiation yielded …

Airborne Path Frequency Based Substructuring Method And Its Applications, Rui He

Theses and Dissertations--Mechanical and Aerospace Engineering

Frequency based substructuring (FBS) is routinely used to model structural dynamics. It provides a framework for connecting structural subsystems together, assessing path contributions, determining the effect of mount modification, and identifying inverse forces. In this work, FBS methods are extended to include acoustic subsystems and connecting pipes and ducts. Connecting pipes or ducts are modeled using the transfer matrix approach which is commonly used for modeling mufflers and silencers below the plane wave cutoff frequency. The suggested approach is validated using boundary element method (BEM) simulation. Applications of the procedure include determining airborne path contributions, the effect of treating ducts …

A Framework For Sustainable Material Selection For Multi-Generational Components, Ryan T. Bradley

Theses and Dissertations--Mechanical and Aerospace Engineering

The early stages of a product’s design are a critical time for decisions that impact the entire life-cycle cost. Product designers have mastered the first generation; however, they currently do not have the ability to know the impact of their decisions on the multi-generational view. This thesis aims at closing the gap between total life-cycle information and the traditional design process in order to harbor sustainable value creation among all stakeholders involved. A framework is presented that uses a combination of a life-cycle costing methodology and an evolutionary algorithm in order to achieve a sustainability assessment for a true multi-generational …

Modeling Of Spallation Phenomenon In An Arc-Jet Environment, Raghava Sai Chaitanya Davuluri

Theses and Dissertations--Mechanical and Aerospace Engineering

Space vehicles, while entering the planetary atmosphere, experience high loads of heat. Ablative materials are commonly used for a thermal protection system, which undergo mass removal mechanisms to counter the heat rates. Spallation is one of the ablative processes, which is characterized by the ejection of solid particles from the material into the flow. Numerical codes that are used in designing the heat shields ignore this phenomenon. Hence, to evaluate the effectiveness of spallation phenomenon, a numerical model is developed to compute the dynamics and chemistry of the particles. The code is one-way coupled to a CFD code that models …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

Development And Validation Of Finite Element Approaches To Determine The Insertion Loss Of Louvered Terminations Including Parametric Investigations, Huangxing Chen

Theses and Dissertations--Mechanical and Aerospace Engineering

Louvers are employed at the ends of HVAC ducts to direct airflow, provide weather protection, and attenuate noise. This details two finite element approaches that can be used to assess the acoustic attenuation from a louvered termination. In the first approach, plane wave propagation is assumed inside of a duct with a non-reflective source. On the receiver side, a baffled termination is assumed and the radiation condition is simulated using a non-reflective boundary condition called an automatically matched layer. In the second approach, a short aperture is placed between two infinite acoustic spaces. On the source side, a diffuse acoustic …

Joint Formation Under Severely Altered Background Atmosphere In Controlled Atmosphere Brazing Of Aluminum, Cheng-Nien Yu

Theses and Dissertations--Mechanical and Aerospace Engineering

Adverse changes of background atmosphere in a brazing chamber cause qualitative and quantitative deterioration of joint formation in an aluminum brazing process. This study offers an insight into the adverse effects with gradually adjusted atmospheric conditions in terms of oxygen and humidity levels. Corresponding responses of the molten clad flow and the joint formation upon resolidification vs. atmospheric conditions are documented by comparative tests involving self-fluxing and surface-fluxing brazing sheets: 1) in situ and in real time study of the onset of melting, clad flow, and joint formation, and 2) inclined wedge-tee mating tests for brazeability assessment. The surface-fluxing brazing …

Computational Modeling Of Cardiac Biomechanics, Amir Nikou

Theses and Dissertations--Mechanical and Aerospace Engineering

The goal of this dissertation was to develop a realistic and patient-specific computational model of the heart that ultimately would help medical scientists to better diagnose and treat heart diseases. In order to achieve this goal, a three dimensional finite element model of the heart was created using magnetic resonance images of the beating pig heart. This model was loaded by the pressure of blood inside the left ventricle which was measured by synchronous catheterization. A recently developed structurally based constitutive model of the myocardium was incorporated in the finite element solver to model passive left ventricular myocardium. Additionally, an …

Determination Of Isolator Transfer Matrix And Insertion Loss With Application To Spring Mounts, Shishuo Sun

Theses and Dissertations--Mechanical and Aerospace Engineering

Transmissibility is the most common metric used for isolator characterization. However, engineers are becoming increasingly concerned about energy transmission through an isolator at high frequencies and how the compliance of the machine and foundation factor into the performance. In this study, the transfer matrix approach for isolator characterization is first reviewed. Two methods are detailed for determining the transfer matrix of an isolator using finite element simulation. This is accomplished by determining either the mobility or impedance matrix for the isolator and then converting to a transfer matrix. One of the more useful metrics to characterize the high frequency performance …

Radiative Conductivity Analysis Of Low-Density Fibrous Materials, Nima Nouri

Theses and Dissertations--Mechanical and Aerospace Engineering

The effective radiative conductivity of fibrous material is an important part of the evaluation of the thermal performance of fibrous insulators. To better evaluate this material property, a three-dimensional direct simulation model which calculates the effective radiative conductivity of fibrous material is proposed. Two different geometries are used in this analysis.

The simplified model assumes that the fibers are in a cylindrical shape and does not require identically-sized fibers or a symmetric configuration. Using a geometry with properties resembling those of a fibrous insulator, a numerical calculation of the geometric configuration factor is carried out. The results show the dependency …

A Subsystem Identification Approach To Modeling Human Control Behavior And Studying Human Learning, Xingye Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans learn to interact with many complex dynamic systems such as helicopters, bicycles, and automobiles. This dissertation develops a subsystem identification method to model the control strategies that human subjects use in experiments where they interact with dynamic systems. This work provides new results on the control strategies that humans learn.

We present a novel subsystem identification algorithm, which can identify unknown linear time-invariant feedback and feedforward subsystems interconnected with a known linear time-invariant subsystem. These subsystem identification algorithms are analyzed in the cases of noiseless and noisy data.

We present results from human-in-the-loop experiments, where human subjects in- teract …

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical and Aerospace Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Low-Order Discrete Dynamical System For H2-Air Finite-Rate Combustion Process, Wenwei Zeng

Theses and Dissertations--Mechanical and Aerospace Engineering

A low-order discrete dynamical system (DDS) for finite-rate chemistry of H₂-air combustion is derived in 3D. Fourier series with a single wavevector are employed to represent dependent variables of subgrid-scale (SGS) behaviors for applications to large-eddy simulation (LES). A Galerkin approximation is applied to the governing equations for comprising the DDS. Regime maps are employed to aid qualitative determination of useful values for bifurcation parameters of the DDS. Both isotropic and anisotropic assumptions are employed when constructing regime maps and studying bifurcation parameters sequences. For H₂-air reactions, two reduced chemical mechanisms are studied via the DDS. …