Mechanical Engineering Commons^™

Time-Resolved Argon Theta-Pinch Plasma Properties By Line Ratio Method With Collisional-Radiative Model, Warner C. Meeks, Joshua L. Rovey

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Advantages Of A Finite Extensible Nonlinear Elastic Potential In Lattice Boltzmann Simulations, Tai-Hsien Wu, Dewei Qi

The Hilltop Review

A new structure, generalized lattice nonlinear spring model (GLNSM), which adopts non-linear FENE-LJ potential instead of harmonic potential, has been coupled with lattice Boltzmann simulation for solving fluid-solid interaction problem. In this article, a significant work is the relationship between the GLNSM (FENE-LJ potential) and Young’s modulus has been described in detail. A validation has also been presented to prove that GLNSM is reliable.

Fuel Cells As Electric Vehicle Range Extenders, Florida Solar Energy Center, R. Paul Brooker

FSEC Energy Research Center®

Fuel cells were modeled as range extenders for electric vehicles. In this application, the fuel cell would supplement a medium sized (16kWh) battery in order to increase the range of the electric vehicle. The fuel cell range extender is compared to an internal combustion engine (ICE) based range extender in terms of vehicle fuel economy and cost per mile driven. Since the fuel cell is about 40% more efficient than the ICE, the fuel economy of a fuel cell range extender was estimated to be 68 miles per gallon gasoline equivalent (MPGe), while the economy of an ICE range extender …

Contact Analysis For Coupling Of Plates And Screws In Fracture Fixation Of Cortical Bone, Gaffar Gailani, Rachid Moumni, Malek Brahimi

Publications and Research

Internal fixation is a common treatment for bone fracture. Bone fracture occurs due to different reasons such as motor vehicle accidents, falling,…etc. The treatment is performed by fixing plate and screws to the fracture site. Lack of stability of the implants (plates and screws) may lead to delay in healing or failure of treatment. Micro-motion between the implant and the bone may cause formation of fibrous tissue around the screw which will lead to implant loosening. On the other hands, firm fixing of the conventional implants (Dynamic Compression Plates) may lead to delay resorption and delay in healing. Recently, Locked …

Sensible Air To Air Heat Recovery Strategies In A Passive House, Santiago Martin Rodriguez-Anderson

Dissertations and Theses

Due to rising energy costs and concerns about global climate change, high performance buildings are more in demand than ever before. With roughly 20% of the total energy consumption in the United States being devoted to residential use, this sector represents a significant opportunity for future savings. There are many guidelines and standards for reducing building energy consumption. One of the most stringent is the Passive House Standard. The standard requires that that air infiltration is less than or equal to 0.6 air changes per hour at a 50 Pascal pressure difference (ACH 50), annual heating energy is less than …

Propulsion Theory Of Flapping Airfoils, Comparison With Computational Fluid Dynamics, Doug F. Hunsaker, W. F. Phillips

Mechanical and Aerospace Engineering Faculty Publications

The thrust, required power, and propulsive efficiency of a flapping airfoil as predicted by the well-known Theodorsen model are compared with solutions obtained from grid- resolved inviscid computational fluid dynamics. A straight-forward summary of Theodorsen’s flapping airfoil model is presented using updated terminology and symbols. This shows that both axial and normal reduced frequencies are of significant importance. The axial reduced frequency is based on the chord length and the normal reduced frequency is based on the plunging amplitude. Computational fluid dynamics solutions are presented over the range of both reduced frequencies typically encountered in the forward flight of birds. …

Skin-Like Electronics For A Persistent Brain-Computer Interface, Woon-Hong Yeo, Yongkuk Lee

Mechanical and Nuclear Engineering Publications

There exists a high demand for a continuous, persistent recording of non-invasive electroencephalograms in both clinical and research fields. Head-cap electrodes with metal conductors and conductive gels are widely used and considered as the gold standard for such measurement. This physical interface, however, is poorly suited to uninterrupted, long-term use due to the uncomfortable rigid electrodes, skin irritation due to the gel, and electrical degradation as the gel dries. These issues can be addressed by using a newly developed, dry form of electronics. Here, we briefly review a class of soft electronic technology in the aspects of mechanics, materials, and …

Young's Modulus Of [111] Germanium Nanowires, M. Maksud, J. Yoo, C. T. Harris, N. K. R. Palapati, A. Subramanian

Mechanical and Nuclear Engineering Publications

This paper reports a diameter-independent Young’s modulus of 91.9 ± 8.2 GPa for [111] Germaniumnanowires (Ge NWs). When the surface oxide layer is accounted for using a core-shell NW approximation, the YM of the Ge core approaches a near theoretical value of 147.6 ± 23.4 GPa. The ultimate strength of a NW device was measured at 10.9 GPa, which represents a very high experimental-to-theoretical strength ratio of ∼75%. With increasing interest in this material system as a high-capacity lithium-ion battery anode, the presented data provide inputs that are essential in predicting its lithiation-induced stress fields and fracture behavior.

A Field Investigation Of Composite Mud Brick Compressive Strength, Kevin D. Hale

Dissertations, Master's Theses and Master's Reports - Open

It has been highlighted in numerous publications that in the field of earth construction there is a strong disconnect between experimental work in the laboratory and its application in the field. The current study attempts to help bridge this gap with a field test conducted in Nampula, Mozambique. Mud bricks were made with a simple hand mold and reinforced with bamboo and straw fibers. Fibers were cut into lengths of 3 cm and 6 cm while being mixed in fractions of 0.125%, 0.25% and 0.50% by weight and compressive strength was measured using an application of the 3-point bending test. …

Contours For Planar Cracks Growing In Three Dimensions, Louis Milton Brock

Mechanical Engineering Faculty Publications

A three-dimensional dynamic steady state analysis for extension of a semi-infinite plane crack is considered. Fracture is brittle and driven by loads applied to the crack surfaces. An analytical solution is obtained, and examined in light of two criteria: energy release (rate) and strain energy density. Introduction of a quasipolar coordinate system allows, for each criterion, generation of a nonlinear first-order differential equation for the distance from the origin to any point on the crack edge. These in turn give insight into the crack contour generated by the crack edge. In particular, for loading by compressive point forces, the equation …

Traci Impact Assessment Of Transportation Manufacturing Nexus In The U.S.: A Supply Chain-Linked Cradle-To-Gate Lca, Yong Shin Park, Gokhan Egilmez

Mechanical and Industrial Engineering Faculty Publications

Sustainable transportation is an inevitable component of sustainable development intitiatives for mitigating the climate change impacts and stabilizing the rising carbon emissions thus global temperature. In this context, comprehensive analysis of the environmental impact of transportation can play a critical role towards quantifying the midpoint environmental and human health related impacts associated with the transportation activities triggered by manufacturing sectors. This study traces the life cycle impact of the U.S. transportation and manufacturing sectors’ nexus using Tool for the Reduction and Assessment of Chemicals and Other Environmental Impacts (TRACI) in the context of the Economic Input-Output Life Cycle Assessment (EIO-LCA) …

Fsae Pedal Box: Controlling Stop And Go, Christopher Hathcock, Tyler Munden

Capstone Design Expo Posters

The VCU FSAE team has a need for foot controls for the brakes and throttle on their newest race car. The assembly must meet the rules set forth by the FSAE organization to compete, and must be as light and low as possible to conserve the acceleration and handling characteristics of the car. Furthermore, the project must be completed on a budget of $500 allotted to Senior Design teams. The FSAE team has been working on the current car since 2005 and has yet to produce a drivable race car. The Senior Design teams this year cover the major systems …

Vertical Tank Inspection Device, Tyriek Bayne, Sarah Morgan, Donald Reid, Charles Stacy

Capstone Design Expo Posters

Newport News Shipbuilding (NNS) has requested a design for a telescoping arm able to carry out vertical tank inspection aboard ships. This device will play a key role in saving time and money, as well as potentially decreasing health and safety risks. The current system is both time consuming and limited to incremental positioning. A new system will permit inspectors to spend less time and effort at this portion of the tank and possibly complete their task much sooner. Based on design criteria given by Newport News Shipbuilding, a telescoping mechanism will be designed to lower a camera 18 ft. …

Robotic Inspection Of Geometrically Complex Tank Systems, James Dinsmore, Jay Kim, Randolph Snook, Thanh Tran, Trenton Wilhelmi

Capstone Design Expo Posters

The primary focus of this project is to create an autonomous rail based robot to inspect and traverse tanks with the idea of future improvements that would carry out all duties of the refurbishing process. By using a more cost-efficient method of semi-autonomous robotic inspection and refurbishment, Newport News Shipbuilding will be able to reduce the risk of harm and level of manual labor required for the refurbishment process. Additionally, the amount of personal protective equipment that needs disposal should be decreased, thus having a positive impact on the environment.

An initial prototype was developed as a 2013-2014 senior project. …

Formula-Sae: Shift System And Controls, Ashton Bressler, Cody Bryant, Christian Fergusson, Jason Shephard

Capstone Design Expo Posters

Problem statement: Formula SAE has been at VCU for the last three years and the team is now getting to the point of having the formula car ready to run and drive. One of the things that needs to be finished for this to happen is the installation of a shifting system.

Rationale: Once completed, the FSAE team will be one step closer to having a competition ready formula car. While a major part of the team is the members’ love of all things fast, we also believe that the car will provide exposure to the VCU School of Engineering …

Tapered Roller Bearing Test Rig: Axially Loaded Application To Accelerate Bearing Failure, Andrew Compton, Donnie Miller, Thomas Miller, Milton Chandler

Capstone Design Expo Posters

Problem Statement: Fatigue life testing of large tapered roller bearing components for rail applications is often very costly and time consuming. The purpose of this project is to assist Amsted Rail Company, Inc. develop a large railroad tapered roller bearing test rig that does not require scaled down prototypes bearings. As these are tapered rollers, loads can be applied from either the lateral or radial direction. L10 bearing life test predictions for the test rig bearings should be carried out using the American Bearing Manufacturers Association standards. The test rig can be designed to test as many as 4 bearings …

Nuclear Reactor Simulator, Adriana Camargo, Jonathan Dip, Gordan Ek, Vance Petrella, Soeuth Soeun, Nicole Waugh

Capstone Design Expo Posters

VCU’s nuclear reactor simulator provides a real time simulation of the operation of a nuclear power plant. Student developed LabVIEW programs display the controls and instrumentation of a reactor control room on twenty eight computer monitors, thirteen of which are touchscreens. Changing reactor conditions are calculated with the best-estimate nuclear system analysis code RETRAN-3D. Simulator design provides for the interaction between student reactor operators and an instructor through instructor driven reactor transients. The simulator is used as a teaching tool for VCU engineering students and for public education and community outreach. The VCU nuclear simulator is an ongoing senior design …

The Superhydrophobic Boat, Cole Anton, Edin Avdic, Aneesh Sandhir, Tyler Zheng

Capstone Design Expo Posters

The purpose of this project is to successfully design and construct a boat hull while minimizing the amount of solid material in contact with the water. If successful, this experiment could serve as a first step in designing more efficient vessels through the reduction of the water drag force on the object. The approach to this project involved determining the optimal wire mesh and coating combination for the boat hull using both computational methods and experiment.

Radio Controlled Aircraft, Michael Johnson, Dakota Macgill, Robert Peake, Ryan Wydler

Capstone Design Expo Posters

Building an R/C aircraft isn’t exactly a project intent on breaking ground in the field of aerospace engineering, rather it is an opportunity to apply fluid dynamics in a practical manner to gain experience in aeronautical engineering. An aerospace engineer is one who designs and builds aircraft and spacecraft and are often tasked with deeming an aircraft flight worthy or not. We will attempt to predict the feasibility of our custom plane designs using aircraft engineering techniques found through research and through texts provided by our advisor, Dr. Jayasimha. The goal of this design is to design and fabricate a …

Automotive Object Detection Simulator, Ishoc Salaam, Stephen Holder, Taylor Fines

Capstone Design Expo Posters

Can you imagine starting your car, pushing a button, and it drives you to work? This technology is not as far in the future as you may think. Cars such as Mercedes Benz’s S-class and Audi’s A7 prototype have a traffic jam assist feature which at speeds under 40 mph, a button can be pressed and the car will drive itself on the highway. The system uses an array of cameras, sensors, and radars to follow the car in front at a safe distance while staying within its lane. If another car cuts in front of it with the feature …

Industrial Brush Coiler Attachment, Amber Clark, Tim Paredes, Andy Richardson, Kayleigh Rogers, Branden Yam

Capstone Design Expo Posters

Problem Statement: Company initially desired a new machine that would be able to produce external coiled brushes that would help in increasing revenue and project opportunities. The design has shifted to making an attachment to the existing equipment that would help in this effort instead of developing a completely new unit.

Rationale: Sealeze sees this as an opportunity of increasing revenue and also taking on the effort of making externally coiled brushes more efficiently. If successful, more clients can be taken in and it would make Sealeze a more versatile company.

Approach: The main approach revolved around weekly meetings with …

Intelligent Control Of Miniature Holonomic Vertical Take-Off And Landing Robot, Mohammad A. Jaradata, Mohamed Al-Fandia, Omar Alkhatiba, Yousef Sardahi

All Engineering Faculty Research

This paper discusses the development of a fuzzy based controller for miniaturized unmanned aerial vehicle (UAV).This controller is designed to control the center-of-gravity (CoG) in a new configuration of coaxial miniaturized flying robot (MFR). The idea is to shift the CoG by controlling two pendulums located in perpendicular directions; each pendulum ends with a small mass. A key feature of this work is that the control algorithm represents the original nonlinear function that describes the dynamics of the proposed system. The controller model incorporates two cascaded subsystems: PD and PI fuzzy logic controllers. These two controllers regulate the attitude and …

Fsae Rear Differential Carrier, Nicholas Rivero, Peter Quach, Zack Jillani

Capstone Design Expo Posters

The Formula SAE design project enables engineering students to develop, analyze, build, and benchmark a Formula-style racecar. A differential was designed for VCU’s car to ensure that power is evenly distributed to the drive wheels under all possible handling conditions. A mounting system is required to secure the differential to the frame. Failure of this carrier could be catastrophic, therefore precise consideration of all possible forces and loading situations is required for design. A team was developed to examine how dynamic forces and fatigue contribute to component failure. Based on the results of this analysis a differential carrier can be …

Tapered Roller Bearing Accelerated Fatigue Life Test Rig Design, Hilton Bennett, Elizabeth Englert, Beck Grimm, Nathan Morris, Matthew Ofsonka, David Trinh

Capstone Design Expo Posters

Fatigue life testing of large tapered roller bearings for railroad applications is both expensive and time consuming. Accepted methods for testing bearings include full–size and scaled down testing. Currently, bearing test methods at Brenco take up to six months to complete, and scaled down testing requires additional resources for manufacturing prototypes and testing capabilities that are not economically ideal. The purpose of this project is the development of a tapered roller bearing test rig to test bearings to their fatigue life as quickly as possible. The rig design can accommodate bearing sizes in the range of one half (½) to …

Low-Cost Desalination Unit: Direct Contact Membrane Distillation, Meghan Herbert-Walters, Aubrey Martin, Lauren Scolese, Tina Trinh

Capstone Design Expo Posters

According to the United Nations Educational, Scientific, and Cultural Organization (UNESCO), 783 million people do not have access to a reliable clean water source. With this many people in the world without access to clean water, a solution to this problem is highly essential. The objective of this project is to create a low-cost compact desalination unit that can be used to turn contaminated water into pure drinking. For our design, a direct contact membrane distillation (DCMD) approach was used. The DCMD system allows only for the evaporated feed water to pass through the membrane and therefore causes an increase …

The Perfect Coffee Cup, Suzanne Bowers, Jessica Ingram, David Murphy, Gillian Stavlas

Capstone Design Expo Posters

To design a coffee cup that will maintain the coffee at the optimal drinking temperature for several hours using Phase Change Material, PCM. The importance of this project is designing a coffee cup that will retain its temperature for a prolonged period of time giving the consumer plenty of time to finish their coffee at the desired consumption temperature. We designed a double walled cup that would contain the PCM. Heat transfer calculations were done for different materials such as acrylic, glass, and stainless steel with various thicknesses for each material. These calculations were used to decide on the ideal …

Nebraska Summary: S989 Massey Ferguson 8727, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Me-Em 2014-15 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Human-centered Engineering
• Endowed Department Chair
• Enrollment & Degrees
• Graduates
• Department News
• Faculty & Staff
• Alumni
• Donors
• Contracts & Grants
• Patents & Publications
• Faculty & Staff Directory

Stethoscope-Based Detection Of Detorqued Bolts Using Impact-Induced Acoustic Emissions, Joe Guarino, Robert Hamilton

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Results of a preliminary study investigating a simple method for detecting looseness in bolted fasteners of a steel structure are presented. Extensive research by many investigators demonstrates that the frequency response of a bolted structural member changes when one or more bolts are loosened. A simple and effective method for detecting looseness can be applied to bolted joints, using inexpensive and commonly-available equipment and software. The difference between spectrograms associated with tight and loose bolts is clearly apparent due to the presence of a tell-tale mode when one or more bolts are loosened. Further, a striking difference can be elucidated …

Test 2117: John Deere 5115m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …