Mechanical Engineering Commons^™

An Improvement Of Wave Refraction-Diffraction Effect In Swan, Aw-Guei Lin

Journal of Marine Science and Technology–Taiwan

SWAN, a wind wave model, has been modified to take into account wave refraction-diffraction effects from the extended mild-slope equation when wind waves pass through a extremely uneven sea bottom in the presence of current. In our modified model, the diffraction correction parameter introduced by Holthuijsen et al. [10] has been adjusted to better predict the combined effect of the higher-order bottom effect, wave-bottom interaction and wave-current interaction. After a preliminary analysis, the influence of the correction parameter is discussed, and a comparison is made between the original and the new phase-decoupled versions of SWAN through some typical examples of …

An Experimental Study Of Regular Long Crested Waves Over A Crescent Type Shoal, Wen-Kai Weng, Jaw-Guei Lin, Chun-Sien Hsiao

Journal of Marine Science and Technology–Taiwan

Converting the ocean wave energy into electric power is one possibility of the development of alternative and nonpolluting sources of energy. Many researches concerning converters and their converting efficiency of wave power were developed and discussed in the last years. However, converting wave energy into electric power does not only depend upon converting system but condition of sea state essentially. A calm sea state with lower wave energy is difficult to drive converting device working and is unable to satisfy the minimum economical requirement. Unfortunately, wave heights in the sea state around Taiwan are mostly too smaller to extract the …

Assessment Of Solar Photovoltaic Technologies Using Multiple Perspectives And Hierarchical Decision Modeling, Nasir Jamil Sheikh

Dissertations and Theses

The objective of this research is to build a decision model for a comprehensive assessment of solar photovoltaic technologies using multiple perspectives. These perspectives include: social, technological, economic, environmental, and political (STEEP) with each perspective consisting of multiple criteria. Hierarchical decision modeling and expert judgment quantification are used to provide the relative ranking of the perspectives and criteria. Such modeling is effective in addressing technology evaluations with competing and contrasting perspectives and criteria where both quantitative and qualitative measurements are represented. The model is then operationalized by constructing desirability functions for each criterion. The combined results provide an overall numerical …

Universal Scaling And Intrinsic Classification Of Electro-Mechanical Actuators, Sambit Palit, Ankit Jain, Muhammad A. Alam

Birck and NCN Publications

Actuation characteristics of electromechanical (EM) actuators have traditionally been studied for a few specific regular electrode geometries and support (anchor) configurations. The ability to predict actuation characteristics of electrodes of arbitrary geometries and complex support configurations relevant for broad range of applications in switching, displays, and varactors, however, remains an open problem. In this article, we provide four universal scaling relationships for EM actuation characteristics that depend only on the mechanical support configuration and the corresponding electrode geometries, but are independent of the specific geometrical dimensions and material properties of these actuators. These scaling relationships offer an intrinsic classification for …

Solar Powered Airplane: Student Design/Build/Fly Project, Dr. Jerry Bowman

Journal of Undergraduate Research

Involve a significant number of students in a multi-semester project with intense technical challenges and a well-defined objective: The creation of a solar powered airplane with the goal of indefinite flight.

High-Resolution Correlation Spectroscopy Of 13c Spins Near A Nitrogen-Vacancy Centre In Diamond, Abdelghani Laraoui, Florian Dolde, Christian Burk, Friedemann Reinhard, Jorg Wrachtrup, Carlos A. Meriles

Department of Mechanical and Materials Engineering: Faculty Publications

Spin complexes comprising the nitrogen-vacancy centre and neighbouring spins are being considered as a building block for a new generation of spintronic and quantum information processing devices. As assembling identical spin clusters is difficult, new strategies are being developed to determine individual node structures with the highest precision. Here we use a pulse protocol to monitor the time evolution of the 13C ensemble in the vicinity of a nitrogenvacancy centre. We observe long-lived time correlations in the nuclear spin dynamics, limited by nitrogen-vacancy spin–lattice relaxation. We use the host 14N spin as a quantum register and demonstrate that hyperfine-shifted resonances …

Reliability Analysis Of Low-Silver Bga Spheres Comparing Failure Detection Criteria, Briana Fredericks

Industrial and Manufacturing Engineering

One of the challenges of solder joint reliability tests is estimating the time of failure of the solder joint. Failure criteria should be able to detect solder joint failure as early as possible, while minimizing the probability of false detection. The failure mechanism under study is cracks due to thermal fatigue. The most common method to estimate failure due to cracks is to monitor the resistance during testing, because solder imaging and cross-sectioning methods are destructive. Current industry failure criteria do not adequately demonstrate the relationship between the size of the crack and the resulting change in resistance. This project …

Design Of An Apparatus To Detect Small Changes In The Mass Of Rotational Machine Components, Jonathan R.A. Maier, M. Laine Mears, Joshua D. Summers

Publications

In this study, an apparatus was designed to detect changes on the order of grams in the mass of test samples subject to accelerations approaching 275g. The apparatus incorporated a surface speedometer, displacement transducer and on-board data-logging device in order to correlate mass loss events with changes in rotational speed and acceleration. An accessory was also designed to allow for on-board video recording to validate the findings and to better understand the mechanics of mass loss events. Such mass loss events are of interest for high-speed rotating machinery (e.g., manufacturing equipment, turbine rotors and automotive drivetrains), where material can build …

Anisotropic Compositional Expansion And Chemical Potential For Amorphous Lithiated Silicon Under Stress Tensor, Valery I. Levitas, Hamed Attariani

Mechanical and Materials Engineering Faculty Publications

Si is a promising anode material for Li-ion batteries, since it absorbs large amounts of Li. However, insertion of Li leads to 334% of volumetric expansion, huge stresses, and fracture; it can be suppressed by utilizing nanoscale anode structures. Continuum approaches to stress relaxation in Li_xSi, based on plasticity theory, are unrealistic, because the yield strength of Li_xSi is much higher than the generated stresses. Here, we suggest that stress relaxation is due to anisotropic (tensorial) compositional straining that occurs during insertion-extraction at any deviatoric stresses. Developed theory describes known experimental and atomistic simulation …

Correlations Between Internal And External Power Outputs During Weightlifting Exercise, Kristof Kipp, Chad Harris, Michelle B. Sabick

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Identifying loads that maximize mechanical power is important because training at such loads may optimize gains in dynamic athletic performance. The purpose of this study was to examine correlations between measures of external mechanical power output and internal mechanical joint power output across different loads during a weightlifting exercise. Ten subjects performed 3 sets of the clean exercise at 65, 75, and 85% of 1 repetition maximum (1RM). Peak external mechanical power output was calculated with 4 commonly used methods, whereas an inverse dynamics approach was used to calculate peak internal mechanical power output for the hip, knee, and ankle …

Broncoblade: An Open Source Wind Turbine Blade Analysis Tool, Alex R. Quinlan

Masters Theses

This thesis reports the development and validation of BroncoBlade, a horizontal axis wind turbine analysis tool. BroncoBlade prepares finite element models and integrates them with an aeroelastic simulator. Analysis results for the SNL100-00 baseline blade are evaluated against reference results published by Sandia National Laboratories. Variations on the SNL100-00 blade incorporating carbon fiber are compared to the baseline blade.

Computational Analysis To Enhance Laminar Flow Convective Heat Transfer Rate In An Enclosure Using Aerosol Nanofluids, Andrew Hudson

College of Graduate Studies: Theses & Dissertations

The current research intends to provide a starting point to effectively model aerosol heat transfer in a narrow, enclosed body. This research can lead to future modeling of nano fluids including their heat transfer characteristics and erosion effects on the walls of an enclosure. The model was developed using ICEM CFD for the mesh and FLUENT for the fluid flow modeling. Six different aspect ratio enclosures were developed to study the effects of varying aspect ratio. The natural convection of air was developed first to establish the appropriateness of the models being used. A mesh check was performed using one …

Computational Dynamics For The Flexible Multi-Body System, Yu Liu

Mechanical & Aerospace Engineering Theses & Dissertations

Research in computational dynamics has tremendously developed in the recent years because of the demand for analysis and simulation of various multi-body systems in the growing bio-medical, mechanical and aerospace industries. These multi-body systems are made of individual bodies that are interconnected via mechanical joints. Mathematically, these joints that connect the bodies can be described as constraint equations imposed upon the motions of the involved free bodies. This process will result in an equation of motion expressed in the form of a differential-algebraic equation (DAE). This is one of the main difficulties when dealing with the multi-body system because these …

Muscle Synergies Improve Estimation Of Knee Contact Forces During Walking, Benjamin J. Fregly, Jonathan P. Walter, Allison Kinney, Scott A. Banks, Darryl D. D'Lima, Thor F. Besier, David G. Lloyd

Mechanical and Aerospace Engineering Faculty Publications

This study investigates whether use of subject-specific muscle synergies can improve optimization predictions of muscle excitation patterns and knee contact forces during walking. Muscle synergies describe how a small number of neural commands generated by the nervous system can be linearly combined to produce the broad range of muscle electromyographic (EMG) signals measured experimentally. By quantifying the interdependence of individual EMG signals, muscle synergies provide dimensionality reduction for the neural control redundancy problem. Our hypothesis was that use of subjectspecific muscle synergies to limit muscle excitation patterns would improve prediction of muscle EMG patterns at the hip, knee, and ankle …

Enhanced Nucleate Boiling On Horizontal Hydrophobic-Hydrophilic Carbon Nanotube Coatings, Xianming Dai, Xinyu Huang, Fanghao Yang, Xiaodong Li, Joshua Sightler, Yingchao Yang, Chen Li

Faculty Publications

Ideal hydrophobic-hydrophilic composite cavities are highly desired to enhance nucleate boiling. However, it is challenging and costly to fabricate these types of cavities by conventional micro/nano fabrication techniques. In this study, a type of hydrophobic-hydrophilic composite interfaces were synthesized from functionalized multiwall carbon nanotubes by introducing hydrophilic functional groups on the pristine multiwall carbon nanotubes. This type of carbon nanotube enabled hydrophobic-hydrophilic composite interfaces were systematically characterized. Ideal cavities created by the interfaces were experimentally demonstrated to be the primary reason to substantially enhance nucleate boiling

Development Of Cfd Models For The Purposes Of Exploring Free Surface Wave Phenomena, Leonard P. Stoehr

Masters Theses

With the push for finding alternative, green energy sources, the harnessing of energy from ocean and lake waves is becoming a more researched field. To fully understand the behavior of wave interactions and optimize designs to extract this energy, it is necessary to develop computer models that can accurately replicate this behavior. A case is presented in which previous work done using the wave tank found in the Western Michigan University fluids lab is examined. The case involves harnessing the energy generated by ocean waves through the usage of plates of different shapes resting horizontally on the water’s surface. The …

Biodiesel Reactor Design With Glycerol Separation To Increase Biodiesel Production Yield, Budy Rahmat, Imas Siti Setiasih, Roni Kastaman

Makara Journal of Technology

The study consisted of reactor design used for transesterification process, effect of glycerol separation on transesterification reaction, determination of biodiesel quality, and mass balance analysis. The reactor was designed by integrating circulated pump/stirrer, static mixer, and sprayer that intensify the reaction in the outer tank reactor. The objective was to reduce the use of methanol in excess and to shorten the processing time. The results showed that the reactor that applied the glycerol separation was able to compensate for the decreased use of the reactant methanol from 6:1 to 5:1 molar ratio, and changed the mass balance in the product, …

Development Of Seebeck-Coefficient Measurement Systems Using Kelvin-Probe Force Microscopy, Kazutoshi Miwa, Faiz Salleh, Hiroya Ikeda

Makara Journal of Technology

Thermoelectric device is investigated by a number of researchers in order to enhance the thermoelectric efficiency. It is known that the efficiency can be improved by quantum effect. However, it is difficult to measure the thermoelectric characteristics of nanometer-scale structures. Thus a new measurement method is expected to be developed. We propose to apply Kelvin-probe force microscopy (KFM) to characterization of thermoelectric materials. KFM can locally observe surface potential of Fermi energy of a sample without touching the sample surface. In the present paper, we estimate the Seebeck coefficient of thin Si-on-insulator layers using KFM.

Agricultural Drought Pattern In West Java Using Thermal Vegetation Index From Modis-Terra Satellite, Dini Daruati, Rahmatulloh Rahmatulloh, Sri Hardiyanti Purwadhi

Makara Journal of Technology

This study examines agricultural drought paddy fields in West Java. The aims of this research are to know the pattern and distribution of paddy field drought in West Java and the correlation between drought and the physical characteristics. The agricultural drought is obtained from TVI (Thermal Vegetation Index) model. TVI is derived from MODIS Terra satellite image, which is the ratio between the LST (Land Surface Temperature) and EVI (Enhanced Vegetation Index). Physical factors studied are rainfall, l slope, geomorphology, soil drainage, and irrigation areas. The most severe drought occurred in September 2006 because of El Nino, covering 806,564 ha, …

Thickness-Shear Vibration Of A Rectangular Quartz Plate With Partial Electrodes, Huijing He, Jiashi Yang, John A. Kosinski, Ji Wang

Department of Mechanical and Materials Engineering: Faculty Publications

We study free vibration of a thickness-shear mode crystal resonator of AT-cut quartz. The resonator is a rectangular plate partially and symmetrically electroded at the center with rectangular electrodes. A single-mode, three-dimensional equation governing the thickness-shear displacement is used. A Fourier series solution is obtained. Numerical results calculated from the series show that there exist trapped thickness-shear modes whose vibration is mainly under the electrodes and decays rapidly outside the electrodes. The effects of the electrode size and thickness on the trapped modes are examined.

Growth Of Crsi2 Nanostructures Using Crcl2 Powder On Si Substrates, Wen Li, Meng Erchao, Tomoji Matsushita, Shingo Oda, Daisuke Ishikawa, Kaito Nakane, Hirokazu Tatsuoka

Makara Journal of Technology

Chromium disilicide (CrSi2) nanostructures were grown by the exposure of Si (111) substrates to CrCl2 vapor in an argon gas flow at atmospheric pressure without using any metal catalyst. Dependence of the growth condition on the structural property was investigated. Hexagonal-shaped CrSi2 microrods were grown at 750 °C with 0.05 g of CrCl2. As the quantity of CrCl2 increased to 0.1 g, the bundle of CrSi2 nanowires with microrods and web-liked CrSi2 nanostructure with turning angles were grown at 750 °C and 700 °C, respectively. The preliminary discussion on the growth mechanism of CrSi2 micro- and nanostructures was carried out.

Biological Pretreatment Of Oil Palm Frond Fiber Using White-Rot Fungi For Enzymatic Saccharification, Euis Hermiati, Sita Heris Anita, Lucky Risanto, Dyah Styarini, Yanni Sudiyani, Achmad Hanafi, Haznan Abimanyu

Makara Journal of Technology

Oil palm frond is one type of lignocellulosic biomass abundantly and daily available in Indonesia. It contains cellulose which can be converted to glucose, and further processed to produce different kinds of value –added products. The aim of this research is to study the effects of biological pretreatment of oil palm frond (OPF) fiber using Phanerochaete chrysosporium and Trametes versicolor on the enzymatic saccharification of the biomass. The OPF fiber (40-60 mesh sizes) was inoculated with cultures of the two fungi and incubated at 27 °C for 4 weeks. The samples were taken after 1, 2, 3, and 4 weeks …

Electromagnetic Simulation For Thz Antenna-Coupled Microbolometers Operated At Room Temperature, Makoto Aoki, Masanori Takeda, Norihisa Hiromoto

Makara Journal of Technology

Room-temperature terahertz (THz) detectors with higher performance are necessary for utilizing the THz wave in various sensing, spectroscopy and imaging, but even the best ones in the present are still insufficient for the practical applications. This issue is essential especially in the region around 1 THz at which there exists a large technology gap between microwave and middle-infrared. Therefore, we study to develop an antenna-coupled microbolometer to achieve a high-performance THz detector operated at a room-temperature for sensing at around 1 THz frequency wave. In this paper, we present several important features and results obtained from electromagnetic simulations, which help …

Analysis Of Hole Lifetime In Soi Mosfet Single-Photon Detector, Dedy Septono Catur Putranto, Wei Du, Hiroaki Satoh, Atsushi Ono, Purnomo Sidi Priambodo, Djoko Hartanto, Hiroshi Inokawa

Makara Journal of Technology

Hole lifetime in the silicon-on-insulator (SOI) metal-oxide-semiconductor field-effect transistor (MOSFET) singlephoton detector was evaluated by the analysis of drain current histograms for different light intensities and substrate voltages. It was found that the peaks in the histogram corresponding to the larger number of stored holes grew as the gate bias decreased. This was attributed not to the increased light absorption efficiency or collection efficiency of the photo-generated holes, but to the prolonged hole lifetime presumably caused by the higher transverse electric field inside the body of SOI MOSFET.

Recognition System Of Indonesia Sign Language Based On Sensor And Artificial Neural Network, Endang Supriyati, Mohammad Iqbal

Makara Journal of Technology

Sign language as a kind of gestures is one of the most natural ways of communication for most people in deaf community. The aim of the sign language recognition is to provide a translation for sign gestures into meaningful text or speech so that communication between deaf and hearing society can easily be made. In this research, the Indonesian sign language recognition system based on flex sensors and an accelerometer is developed. This recognition system uses a sensory glove to capture data. The sensor data that are processed into feature vector are the 5-fingers bending and the palm acceleration when …

Performance Optimization Of Microbial Fuel Cell (Mfc) Using Lactobacillus Bulgaricus, Rita Arbianti, Tania Surya Utami, Heri Hermansyah, Deni Novitasari, Ester Kristin, Ira Trisnawati

Makara Journal of Technology

Electrical energy needs in Indonesia are expected to continue to rise. The use of petroleum as a source of energy still dominates, although oil reserves in Indonesia are increasingly being depleted. Therefore, there is a need to develop alternative sources of sustainable energy, such as microbial fuel cell (MFC). In this study, Lactobacillus bulgaricus was used as an electricity producer in a dual-chamber MFC reactor. We investigated the maximum electrical energy by varying the bacterial optical density (OD), the operational time of MFC, the reactor volume, the electrolyte solution, and the configuration of MFC reactor. In this study, the maximum …

An Investigation To Advance The Technology Readiness Level Of The Centaur Derived On-Orbit Propellant Storage And Transfer System, Nathan L. Silvernail

Doctoral Dissertations and Master's Theses

This research was carried out in collaboration with the United Launch Alliance (ULA), to advance an innovative Centaur-based on-orbit propellant storage and transfer system that takes advantage of rotational settling to simplify Fluid Management (FM), specifically enabling settled fluid transfer between two tanks and settled pressure control. This research consists of two specific objectives: (1) technique and process validation and (2) computational model development. In order to raise the Technology Readiness Level (TRL) of this technology, the corresponding FM techniques and processes must be validated in a series of experimental tests, including: laboratory/ground testing, microgravity flight testing, suborbital flight testing, …

Creating Standards Compliant Biodiesel Production Capability Using Waste Peanut Oil At Embry-Riddle Aeronautical University, Jintana Nina Phanthanousy

Doctoral Dissertations and Master's Theses

During the past year, Embry-Riddle Aeronautical University has been in the process of making a viable biodiesel using waste peanut oil from a Chick-Fil-A fast food restaurant on campus. Past research and biodiesel production from the previous two years on campus was taken into consideration and a catalyst change was proposed. Sample test batches were conducted to create a viable biodiesel and a consistent recipe. The biodiesel was tested for quality and also sent in for ASTM Standards testing. Biodiesel that passed quality testing would be permitted to be used as a B100 in campus facilities and university projects. It …

Multiphase Screen Development, Chris Tarrant

Honors Theses

This honors thesis research project was the study and development of a compact separation device for the oil and gas industry involving a multiphase cylindrical screen filter. Cylindrical screens can be used for solids removal in multiphase flow in upstream oil and gas applications. This study focused on cylindrical wire-wrap screen test unit design and performance characterization to determine volumetric flow rate and pressure drop correlations.

The project goals were met with research, test unit design, CFD modeling, calculations, and physical testing. The comprehensive testing will take place during the summer of 2013 and is planned to consist of building …

Approaches To 30% Energy Savings At The Community Scale In The Hot-Humid Climate, Florida Solar Energy Center, Stephanie Thomas-Rees

FSEC Energy Research Center®

The Building America Partnership for Improved Residential Construction, formerly the Building America Industrialized Housing Partnership, has worked with several community-scale builders within the hot-humid climate zone to improve performance of production-, or community-scale, housing. Tommy Williams Homes (Gainesville, Florida), LifeStyle Homes (Melbourne, Florida), and Habitat for Humanity (various locations, Florida) have all been continuous partners of the Building America Program. The activities of these partners, described in this report, achieved the Building America goal of 30% whole-house source energy savings using packages adopted at the community scale. For new homes, the reference case is the B10 Benchmark, aligned with 2009 …