Mechanical Engineering Commons^™

Study Of Cell Viability During Laser Direct Writing Of Cell-Alginate Suspension, Hemanth Gudapati

All Theses

Laser-assisted cell printing, developed based on Matrix-assisted pulsed-laser evaporation direct-write (MAPLE DW), a typical LIFT (laser-induced forward transfer) practice, has been emerging as one of the most promising biofabrication techniques. Alginate, particularly sodium alginate, is extensively used as the constituent of bioink in laser-assisted cell printing. However, thus far, studies investigating the effect of alginate gelation on cell viability in laser-assisted cell printing are lacking. The objective of this study is to investigate the effects of gelation, gelation time, sodium alginate concentration, and the effect of operating conditions such as the laser fluence on post-transfer cell viability during laser-assisted cell …

Novel Airframe Design For The Dual-Aircraft Atmospheric Platform Flight Concept, Eric Michael Mckee

Doctoral Dissertations and Master's Theses

A high-altitude, long-endurance unmanned aerial airframe was designed for the innovative Dual-Aircraft Atmospheric Platform flight concept that exploits stratospheric wind velocity gradients to remain aloft indefinitely. Classical aircraft preliminary design techniques and high-fidelity tools were used to establish a baseline configuration.

Performance characteristics of numerous airfoil profiles were evaluated with two-dimensional flow software in an effort to determine the best-candidate airfoil for the unique application. Vortex-Lattice method tools were used to investigate the sensitivity of three-dimensional design parameters upon overall vehicle aerodynamic performance and determine both static and dynamic stability characteristics of the airframe. Performance capabilities of the finalized airframe …

Investigation Of Shroud Geometry To Passively Improve Heat Transfer In A Solar Thermal Storage Tank, Matthew Keene Zemler

Doctoral Dissertations and Master's Theses

A shroud and baffle configuration is used to passively increase heat transfer in a thermal store. The shroud and baffle are used to create a vena contracta near the surface of the heat exchanger, which will speed up the flow locally and thereby increasing heat transfer. The goal of this study is to investigate the geometry of the shroud in optimizing heat transfer by locally increasing the velocity near the surface of the heat exchanger. Two-dimensional transient simulations are conducted. The immersed heat exchanger is modeled as an isothermal cylinder, which is situated at the top of a solar thermal …

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

A Study Of Hdpe In High Pressure Of Hydrogen Gas: Measurement Of Permeation Parameters And Fracture Criteria, Sompong Prachumchon

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The permeation parameters of hydrogen gas in high density polyethylene (HDPE) system are sought by comparison with a diffusion model. The method of Green’s functions is used to obtain solutions for the diffusion model. Permeation parameters are found from transient experimented data during two processes; pressurization followed by depressurization. The mechanical compression of HDPE during the pressurization process resulted in lower diffusivity coefficient values and higher solubility values. The results show that the diffusivity coefficient value in the pressurization process is 37% of that during the depressurization process. At the start of the depressurization process, a short-duration fast flow rate …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …

Performance Characterization Of Complex Fuel Port Geometries For Hybrid Rocket Fuel Grains, Andrew Bath

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Extensive research in hybrid rocket motors has taken place at the department of Mechanical and Aerospace Engineering at USU (Utah State University) in the last several years. USU has one of the few facilities in the country capable of static-test firing rocket motors on-campus, which allows for fast-paced testing and development not available elsewhere. Research has involved investigating propulsion devices for a range of applications, including micro-satellite thrusters, hot-gas generators, and even jet-assisted takeoff kick motors. Hybrid motors have the advantage of safety over any other chemical propulsion. Since the fuel and oxidizer are stored seperately, they are relatively inert …

Closed-Loop Thrust And Pressure Profile Throttling Of A Nitrous Oxide/Hydroxyl-Terminated Polybutadiene Hybrid Rocket Motor, Zachary W. Peterson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Hybrid motors that employ non-toxic, non-explosive components with a liquid oxidizer and a solid hydrocarbon fuel grain have inherently safe operating characteristics. The inherent safety of hybrid rocket motors offers the potential to greatly reduce overall operating costs. Another key advantage of hybrid rocket motors is the potential for in-flight shutdown, restart, and throttle by controlling the pressure drop between the oxidizer tank and the injector. This research designed, developed, and ground tested a closed-loop throttle controller for a hybrid rocket motor using nitrous oxide and hydroxyl-terminated polybutadiene as propellants. The research simultaneously developed closed-loop throttle algorithms and lab scale …

Design And Construction Of A Tunable Light Source With Light Emitting Diodes For Photosynthetic Organisms, Nathan Phillipps

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis describes and documents the design and construction of a light source which is tunable and has the ability to mimic the spectral output of the sun in the photosynthetic active radiation range (400 - 700 nm). To adjust the spectral output at different wavelengths different types of LEDs were chosen and combined. This thesis describes the design, construction, testing, and suggestions for further improvements to this light source. The light source is comprised of 900 LEDs with 26 different peak wavelengths within the photosynthetically active radiation range. The light source is made tunable through the use of a …

Cable Median Barrier Failure Analysis And Remediation, Cody S.. Stolle

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

On divided roadways, cross-median fatalities are disproportionately overrepresented in fatal and serious injury crashes. Many state DOTs sought to mitigate cross-median crash risk by installing cable median barriers. Despite increased crash rates, studies evaluating crash rates before and after cable median barriers were installed indicated excellent improvement in overall safety.

Although cable median barriers are intended to prevent serious cross-median crashes, cable barriers can also contribute to serious injury and fatality crashes which would not have otherwise occurred, including penetration and rollover crashes. In order to reduce the frequency of undesirable penetration and rollover crashes occurring with cable median barriers …

Predicting Vehicle Dynamics For Roadside Safety Using Multibody Systems Simulations, Brett D. Schlueter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Accurate means for predicting vehicle dynamics is required in the design and testing of roadside safety hardware. Past research has used finite element (FE) modeling to this end, but multibody systems (MBS) modeling may provide a more efficient way to solve these problems. MBS modeling using Adams/Car was investigated by first compiling an introduction to the program, then performing basic vehicle dynamics simulations using a supplied model. Next, a model of a 2270 kg pickup was created and validated against physical test data involving impact with a speed bump. Finally, pickup trajectories in 4H:1V and 6H:1V V-ditches were predicted for …

Modular Joystick Design For Virtual Reality Surgical Skills Training, Michael Head

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A modular control interface and simulated virtual reality environment was designed and created in order to determine how the kinematic architecture of a control interface affects minimally invasive surgery. A user is able to selectively determine how many, the type, and location of degrees of freedom they require for the specific surgical simulation through the use of modular joints and constraint components. Furthermore, passive locking was designed and implemented through the use of inflated latex tubing around rotational degree of freedom joints. It is believed these features will have the ability to effectively simulate a variety of surgical simulations and …

An Optimization-Based Method Of Traversing Dynamic S-Pareto Frontiers, Patrick K. Lewis

Theses and Dissertations

The use of multiobjective optimization in identifying systems that account for changes in customer needs, operating environments, system design concepts, and analysis models over time is generally not explored. Providing solutions that anticipate, account for, and allow for these changes over time is a significant challenge to manufacturers and design engineers. Products that adapt to these changes through the addition and/or subtraction of modules can reduce production costs through product commonality, and cater to customization and adaptation. In terms of identifying sets of non-dominated designs, these changes result in the concept of dynamic Pareto frontiers, or dynamic s-Pareto frontiers …

Compression Transmission Collar For Fastening, David Lecronier, Patrick Atkinson

Mechanical Engineering Patents

A compression transmission collar apparatus for implantation into a bone with a hole having a hole wall comprising an intramedullary nail defining a bore and a threaded fastener and a compression transmission collar including an exterior face and a top edge and a bottom edge and a first end interstcting the top edge at an acute angle and the bottom edge at an obtuse angle and a second end intersecting the top edge at an obtuse angle and the bottom edge at an acute angle and the first end partially overlapping and opposing the second end to define a slit …

Measurement Of Thermal Diffusivities Using The Distributed Source, Finite Absorption Model, James B. Hall

Theses and Dissertations

Thermal diffusivity in an important thermophysical property that quantifies the ratio of the rate at which heat is conducted through a material to the amount of energy stored in a material. The pulsed laser diffusion (PLD) method is a widely used technique for measuring thermal diffusivities of materials. This technique is based on the fact that the diffusivity of a sample may be inferred from measurement of the time-dependent temperature profile at a point on the surface of a sample that has been exposed to a pulse of radiant energy from a laser or flash lamp. An accepted standard approach …

A Hybrid Bishop-Hill Model For Microstructure Sensitive Design, Ribeka Takahashi

Theses and Dissertations

A method is presented for adapting the classical Bishop-Hill model to the requirements of elastic/yield-limited design in metals of arbitrary crystallographic texture. The proposed Hybrid Bishop-Hill (HBH) model, which will be applied to ductile FCC metals, retains the `stress corners' of the polyhedral Bishop-Hill yield surface. However, it replaces the `maximum work criterion' with a criterion that minimizes the Euclidean distance between the applicable local corner stress state and the macroscopic stress state. This compromise leads to a model that is much more accessible to yield-limited design problems. Demonstration of performance for the HBH model is presented for an extensive …

Can Silver Be A Reliable Current Collector For Electrochemical Tests?, Yunhui Gong, Changyong Qin, Kevin Huang

Faculty Publications

The true functionality of a current collector employed in electrochemical cells is to ensure a low- resistance steady electrons flow between the cell and instrumentation without involving in any local electrochemical reactions of the electrode. In this study, we investigated the effect of curing temperature of a common current collector, silver, on the polarization area specific resistance (ASR) of a cathode. The results explicitly showed that at least one order of magnitude lower ASR for a cathode with Ag cured at 800°C than that cured at 650°C of the same cathode configuration. Microscopic analysis of the 800°C-cured cells revealed a …

Physico-Chemical, And Sensory Properties Of Soy Based Gouda Cheese Analog Made From Different Concentration Of Fat, Sodium Citrate And Various Cheese Starter Cultures, Abu Amar, Ingrid Suryanti Surono

Makara Journal of Technology

Gouda cheese analog (GCA) was made using soy protein isolate (SPI), skim milk powder (SMP), fat (palm fat and butter fat), and water (W) at optimal ratio of SPI : SMP : F : W = 14 : 6 : 20 : 60. The effects of butter fat, sodium citrate, and cheese starter culture on the sensory properties of ripened product were assessed by preference test, hedonic test, and the texture profile analysis (TPA) of GCA. The free fatty acids, water-soluble nitrogen, and reduction in pH value of progel were also measured. The use of 100% butter fat (BF) produced …

Effects Of Deposition Parameters And Oxygen Addition On Properties Of Sputtered Indium Tin Oxide Films, Badrul Munir, Rachmat Adhi Wibowo, Kim Kyoo Ho

Makara Journal of Technology

Indium tin oxide (ITO) films were sputtered on corning glass substrate. Oxygen admixture and sputtering deposition parameters were optimized to obtain the highest transparency as well as lowest resistivity. Structural, electrical and optical properties of the films were then examined. Increasing deposition rate and film thickness changed the crystallographic orientation from (222) to (400) and (440), as well as higher surface roughness. It was necessary to apply substrate heating during reposition to get films with better crystallinity. The lowest resistivity of 5.36 x 10-4 Ω•cm was obtained at 750 nm film thickness. The films’ resistivity was increased by addition of …

The Effect Of Rubber Mixing Process On The Curing Characteristics Of Natural Rubber, Abu Hasan, Rochmadi Rochmadi, Hary Sulistyo, Suharto Honggokusumo

Makara Journal of Technology

This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously …

Observation Of Center Disaster Damage On Pariaman And Wasior Using Differential Sar Interferometry (Dinsar), Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

This study focuses on disaster observations in Pariaman (West Sumatera) and Wasior (Papua) using remote sensing techniques (differential SAR interferometry). Differential interferometry (DInSAR) method was performed on two PALSAR data sets with different acquisition months, i.e. about a month after and before disaster, respectively. The center damage of Pariaman earthquake and Wasior flood can be determined by deriving Land Subsidence using DInSAR method.

Coastal Physical Vulnerability Of Surabaya And Its Surrounding Area To Sea Level Rise, Sayidah Sulma, Eko Kusratmoko, Ratna Saraswati

Makara Journal of Technology

The study for coastal vulnerability to sea level rise was carried out in Surabaya and its surrounding area, it has focused on calculations of the physical vulnerability index were used coastal vulnerability index (CVI) methods. It was standardized by the multi criteria analysis (MCA) approach according to the study area. The score of each physical variable derived from remote sensing satellite data and the results of studies that have been done, such as modeling results and thematic maps, and then integrated into geographic information systems (GIS). Result of this study shows that the coastal areas of Gresik, Surabaya, and Sidoarjo …

The Effect Of Size And Crumb Rubber Composition As A Filler With Compatibilizer Pp-G-Ma In Polypropylene Blends And Sir-20 Compound On Mechanical And Thermal Properties, Erna Frida

Makara Journal of Technology

Having been researched the development of thermoplastic elastomer material of polypropylene and natural rubber SIR- 20 compound with Crumb Rubber as the filler. Reinforced polypropylene with size 60 mesh with 1 mm, and the composition of the Crumb rubber (30, 40, and 50) wt%. Observed mechanical properties are tensile strength, fracture elongation, Young's modulus, tear strength and impact strength. Thermal properties are analyzed by DSC and DTA/TGA. It is acquired that for the size of 60 mesh crumb rubber tensile strength, fracture elongation, Young’s modulus, tear strength and impact strength are bigger than 1mm size. The addition of 60 mesh …

Development Of Local-Economic-Development Small And Medium Industries (Led-Sme) In East Java, Rachmad Hidayat, Sabarudin Akhmad

Makara Journal of Technology

This paper presents the effects of Indonesian government’s developmental efforts of assistance and training performed on the growth of LED-SME business units and business performance. Both parameters of the government’s assistance and training were used to analyze the impact to the growth and performance of business unit. To achieve a comprehensive result, samples acquired in this research were about 190 entrepreneurs and managers of LED-SME from East Java. Based on the parameters above, there are five hypotheses made to prove the relationship of the assistance and training to the growth and performance of business units. The structural equation modeling (SEM) …

Cdm Potential In Palm Solid Waste Cogeneration As An Alternative Energy In Aceh Province, Mahidin Mahidin, Izarul Machdar, Muhammad Faisal, Muhammad Nizar

Makara Journal of Technology

Empty Fruit Bunch (EFB) as a solid waste in Crude Palm Oil (CPO) industry does not utilized yet as an alternative energy source to generate electricity. It is well known that use of solid wate (biomass) as an energy source is part of the Clean Development Mechanism (CDM) scheme due to direct reduction of Green House Gases (GHGs) emission and provide a direct contribution to sustainable development. Utilization of EFB as a source of energy is very potential to be implemented in Aceh since this province has 25 CPO Mills at the moment which actively produce about 870,000 ton EFB …

Small Scale Experiment: Thermal Performance Comparison Between Fiber-Cement Roof And Photovoltaic Roof In Malang, Indonesia, Nurhamdoko Bonifacius, Sri Nastiti Nugrahani Ekasiwi

Makara Journal of Technology

Irradiation on the surface of photovoltaic module heats up the photovoltaic module itself and the room underneath the roof of integrated photovoltaic building in the tropics area. Room heating reduces thermal condition and photovoltaic module surface heating reduces its performance in generating electricity. This paper discusses an experiment of measuring the surface temperature of photovoltaic modules and fiber-cement roof surface as a comparison. This experiment also measures the impact of rising temperatures in each space underneath. It used small-scale mock-ups exposed to direct sunlight. The result of the experiment shows that photovoltaic roof surface temperature is lower than fiber-cement roof …

Improved Optical Probe For Measuring Phytoplankton Suspension Concentrations Based On Optical Fluoresensce And Absorption, Retno Wigajatri Purnamaningsih, Nining Betawati Prihantini

Makara Journal of Technology

This paper discusses the results of improved optical probe that works according to optical fluorescence and absorption phenomena for measuring the phytoplankton suspension concentrations. Measurements are made on the Scenedesmus sp. culture. The laboratory test has shown that range of concentration from 104 up to around 1 x 106 cells/mL; fluorescence intensity at λ = 685 nm; and logarithmic of transmission intensity at λ = 405 nm are proportional to the cell concentration linear with proportional constant γ = 4 × 10-5 and β = –2 × 10-7 mL/cell respectively.

Mechanical And Thermal Properties Of Polypropylene Reinforced By Calcined And Uncalcined Zeolite, Nurdin Bukit

Makara Journal of Technology

This study was carried out to compare mechanical and thermal properties of polypropylene (PP) reinforced with uncalcined and calcined zeolites. The PP samples were reinforced with zeolites at various quantities of 2, 4, and 6 (wt %). The comparison of the two types of zeolite was based on mechanical properties, including tensile strength, elongation at break, and Young’s modulus, and thermal characteristics analyzed using DSC, and DTA/TGA technique. The results obtained clearly revealed that both zeolites were able to significantly increase tensile strength and Young’s modulus of the samples, with calcined zeolite was found to work better. Addition of calcined …

Benchmark For Country-Level Earthquake Strong-Motion Instrumentation Program, Widjojo Adi Prakoso, I Nyoman Sukanta

Makara Journal of Technology

An empirical study to develop benchmark models at country-level to assess the suggested number of earthquake strongmotion stations based on a framework encompassing geographic, demographic, and socio-economic parameters is reported. The models are to provide a working estimate of the required number of stations for improving the strongmotion instrumentation program of Indonesia. National earthquake strong-motion networks of New Zealand, Japan, Taiwan, Iran, Turkey, and Italy were used as the references. The parameter proposed is the number of stations in land area of 1,000 km2, and three models based on the exponential regression analysis are presented as functions of population density, …

Worst Case Of Relative Disturbance Gain Array For Uncertain Distillation System, Rudy Agustriyanto, Jie Zhang

Makara Journal of Technology

This article discusses the constrained nonlinear optimization formulation for calculating the worst case of lower and upper bounds of relative disturbance gain array (RDGA) for uncertain process models. The proposed approach seeks the minimum and maximum values of the relative disturbance gains subject to the constraints in which the process and disturbance gains are within their uncertainty ranges. RDGA ranges are useful for control structure determination and the related robustness, as they provide information regarding the sensitivity to gain uncertainties. The proposed method is demonstrated by ternary distillation column case study. Closed loop simulation results support the analysis based on …