Mechanical Engineering Commons^™

Some Considerations For Regional Airline Operations On Contaminated Runways., Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Understanding Industrial Energy Use Through Lean Energy Analysis, Brian Abels, Franc Server, J. Kelly Kissock, Dawit Ayele

Mechanical and Aerospace Engineering Faculty Publications

Due to rising energy costs and global climate change, many industries seek to improve their energy efficiency. This paper describes a three-step method to analyze utility billing, weather, and production data to understand a company’s energy performance over time. The method uses regression modeling of utility billing data against weather and production data. The regression models are then driven with typical weather and production data to calculate the ‘normal annual consumption’, NAC. These steps are repeated on sequential sets of 12 months of data to generate a series of ‘sliding’ NACs and regression coefficients. The method can quantify successful energy …

Advanced Thermal Models For Improved Design Of Counter Flow Microchannel Heat Exchangers, Bobby Mathew

Doctoral Dissertations

Theoretical models of counter flow microchannel heat exchangers subjected to scaling and secondary effects are developed in this dissertation. The scaling effects studied include axial heat conduction and viscous dissipation, while the secondary effects considered in this dissertation is that of external heat transfer via heat flux and temperature. The theoretical models developed are one-dimensional and consist primarily of ordinary governing equations that describe the axial variation of hot and cold fluid. For the case of axial heat conduction, the axial variation of wall temperature is also modeled. The models are dependent on various factors, such as Reynolds number, Prandtl …

The Solvent Effectiveness On Extraction Process Of Seaweed Pigment, Warkoyo Warkoyo, Elfi Anis Saati

Makara Journal of Technology

Eucheuma cottonii seaweed is a species of seaweed cultured in Indonesian waters, because its cultivation is relatively easy and inexpensive. It has a wide variety of colors from green to yellow green, gray, red and brown, indicating photosynthetic pigments, such as chlorophyll and carotenoids. An important factor in the effectiveness of pigment extraction is the choice of solvent. The correct type of solvent in the extraction method of specific natural materials is important so that a pigment with optimum quality that is also benefical to the society can be produced. The target of this research is to obtain a high …

Long Term Surface Power Generator Design For Mars: Autonomously Deployable Photovoltaic Solar Arrays Along With Regenerative Fuel Cell Modules, Omer Demirok

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis studies the feasibility of incorporating a large autonomously deployed photovoltaic solar array power system as the primary power source for a large fixed Mars base. A mission duration of 10 Earth years has been assumed and the nominal power demands have been specified as a minimum of 40 kW, during daytime operation and a continuous 10 kW. demand for nighttime operation.

The overall system design developed in this thesis has an estimated total mass of 7,400 kg, when utilizing hydrogenated amorphous silicon thin film solar arrays and an estimated total mass of 5,100 kg when utilizing polycrystalline copper-indium-diselenide …

Multidisciplinary Design Optimization Of Transonic Airfoil Sections Using Multiobjective Optimization And Computational Intelligence Tools, Amit A. Kulkarni

Mechanical & Aerospace Engineering Theses & Dissertations

The design of transonic airfoils for civil aviation applications has been a major engineering challenge in the last fifty years. This design problem arises due to the need to limit shock wave drag at a given transonic speed. In recent years, the requirement to reduce the levels of aircraft noise has started to affect the airfoil design process. The multidisciplinary aerodynamic shape optimization problem is treated in this thesis using a multi-objective approach. The objectives correspond to the design of transonic airfoil sections with low drag during cruise and low trailing edge noise levels during the approach condition. The optimization …

Parametric Study Of Gear Rattle And The Effect Of Flexible Enclosures On Gearbox Vibratory Responses, Joshuah Thomas Racine

Masters Theses

Gearbox noise emitted from vehicles has become of particular importance to manufacturers due to the significant reduction of engine and masking noises in most modem designs. The reduction of gearbox rattle was the subject of this research using Romax Designer. Both drive and neutral loading conditions were considered for a parametric study of the influence of altering input torque fluctuation, backlash between gears, component rigidities and driveline inertia. Next, an external enclosure was added, where its effect was studied by altering the wall thickness, material properties and fixed boundary positions. Finally, results obtained from Romax Designer for a physical gearbox …

Ultrasonic And Stereo-Optical Characterization Techniques For Applications In Mechanical Testing, Jonathan M. Hein

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

This thesis considers methods developed based on ultrasonic reflections from interfaces and stereo-optical surface strain measurements to study the mechanical characterization of materials and bodies. The ultrasonic method is used to characterize wave speed and attenuation for highly attenuating samples. The stereo-optical strain measurements are used to characterize the effects of genes on mechanical properties of bone, and the dynamic characterization of blast waves in the UNL Shock Wave Trauma Mechanics facility.

A method is described and developed for characterizing the wave speed and attenuation spectrums from reflected waves from the contact surface with an unknown material. The method is …

On-Board Monitoring Of Engine Oil, Ryan James Clark

Masters Theses

Engine oil condition was quantified in a diesel engine through direct, real-time measurements of lubricant properties using an on-board oil-condition sensor. The sensor measures the lubricant temperature, density, dynamic viscosity and dielectric constant. Comparative bench-top experiments using ASTM methods or equivalent techniques validated the accuracy and precision of the lubricant property measurements from the oil-condition sensor for a specific temperature range. Bench-top experiments were also used to establish correlations between fuel contamination levels and changes in lubricant properties.

Through engine experiments, the change in the lubricant properties with respect to operating time was quantified. A correlation was found between the …

Comparison Of Martin’S Empirical Correlation With Measurements On A Compact Plate Heat Exchanger, Abdulmohsen A. Alothman

Masters Theses

The need for more effective heat exchangers is becoming more necessary these days. At the same time, the size of the heat exchanger also plays a big role. Therefore, in many applications the compact plate heat exchanger is used where high effectiveness and small size are required. As a result, it is a necessary to study and understand the performance of compact plate heat exchangers. More specifically, the performance of heat transfer, represented by the Colburn factor j, and friction factor f, must be deeply studied and understood.

A mathematical model has been built to express f and j factors …

Research On Coupled Human And Natural Systems (Chans): Approach, Challenges, And Strategies, Marina Alberti, Heidi Asbjornsen, Lawrence A. Baker, Nicholas Brozović, Laurie E. Drinkwater, Scott A. Drzyzga, Claire A. Jantz, José Fragoso, Daniel S. Holland, Timothy A. Kohler, Jianguo Liu, William J. Mcconnell, Herbert D. G. Maschner, James D. A. Millington, Michael Monticino, Guillermo Podestá, Robert Gilmore Pontius Jr., Charles L. Redman, Nicholas J. Reo, David J. Sailor, Gerald Urquhart

Mechanical and Materials Engineering Faculty Publications and Presentations

Understanding the complexity of human–nature interactions is central to the quest for both human well-being and global sustainability. To build an understanding of these interactions, scientists, planners, resource managers, policy makers, and communities increasingly are collaborating across wide-ranging disciplines and knowledge domains. Scientists and others are generating new integrated knowledge on top of their requisite specialized knowledge to understand complex systems in order to solve pressing environmental and social problems (e.g., Carpenter et al. 2009). One approach to this sort of integration, bringing together detailed knowledge of various disciplines (e.g., social, economic, biological, and geophysical), has become known as the …

Circuit Design For Sensor Detection Signal Conditioner Nitrate Content, Robeth Viktoria Manurung, Aminuddin Debataraja, Hiskia Hiskia

Makara Journal of Technology

Circuit Design for Sensor Detection Signal Conditioner Nitrate Content. Nitrate is one of macro nutrients very important for agriculture. The availability of nitrate in soil is limited because it is very easy to leaching by rain, therefore nitrate could be contaminated ground water by over-process of fertilizer. This process could also produce inefficiency in agriculture if it happened continuesly without pre-analysis of farm field. The answer those problems, it is need to develop the ion sensor system to measure concentrations of nitrat in soil. The system is consist of nitrate ion sensor device, signal conditioning and data acquisition circuit. The …

Production Of Lovastatin And Sulochrin By Aspergillus Terreus Using Solid State Fermentation, Rizna Triana Dewi, Nina Artanti, Hani Mulyani, Puspa Dewi Narrij Lotulung, Minarti Minarti

Makara Journal of Technology

Lovastatin is an anti-cholesterol agent that was produced by Aspergillus terreus using solid state fermentation (SSF). During this fermentation process, sulochrin is also produced as an unwanted co-metabolite. However, our previous result showed that sulochrin had potential as antidiabetes because it is an inhibitor agent of α-glucosidase. In this paper, we reported our observation on lovastatin and sulochrin production pattern in relation with inhibitor α-glucosidase activity during eleven days fermentation of A. terreus koji (SSF) ethyl acetate extract. Koji obtained from solid state fermentation with rice as the substrate and incubated at room temperature, sample is taken daily for eleven …

The Zonation Of Abration Speed Characteristics And Its Handling Technique Of Jalinbar Of North Bengkulu As Vital Band Transportation, Suwarsono Suwarsono, Supiyati Supiyati, Suwardi Suwardi

Makara Journal of Technology

The Zonation of Abration Speed Characteristics and its Handling Technique of Jalinbar of North Bengkulu as Vital Band Transportation. Jalinbar Bengkulu is a vital infrastructure for traffic service, goods, agriculture products, mining, plantation and oils distribution. Abration due to scour of seawater often make these roads jammed and discrupts the peoples economy movement. The aims of this research was to investigate the abration speed of all segment of Jalinbar. The research method was a combination of two methods: A determination of swash energy of sea water using photometer and determination of rocks binding energy using douche method. The result shows …

The Formation Design Of Noise Reducers From Plywood, Foam, Tray, Dan Coconut Fiber For Static Sources, Melati Ferianita Fachrul, Wisnu Eka Yulyanto, Asharani Merya

Makara Journal of Technology

The Formation Design of Noise Reducers from Plywood, Foam, Tray, dan Coconut Fiber for Static Sources. Research was conducted in a semi-anechoic room using a method referring to the ISO 3745. The design used is the Hemisphere in which the source of noise is analogous to engines in an industry. The value reduction in the rate of sound power is obtained by comparing the sound power level before and after control is given. The noise control test materials used consist of layers of plywood, foam, fiber and tray (egg box). The effectiveness of these materials is tested by measuring the …

Measuring Progress With Normalized Energy Intensity, Nathan Lammers, J. Kelly Kissock, Brian Abels, Franc Server

Mechanical and Aerospace Engineering Faculty Publications

Energy standard ISO 50001 will require industries to quantify improvement in energy intensity to qualify for certification. This paper describes a four-step method to analyze utility billing, weather, and production data to quantify a company's normalized energy intensity over time. The method uses 3-pararameter change-point regression modeling of utility billing data against weather and production data to derive energy signature equations. The energy signature equation is driven by typical weather and production data to calculate the 'normal annual consumption', NAC, and divided by typical production to calculate 'normalized energy intensity' NEI. These steps are repeated on sequential sets of 12 …

Optimizing Compressed Air Storage For Energy Efficiency, Brian Abels, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Compressed air storage is an important, but often misunderstood, component of compressed air systems. This paper discusses methods to properly size compressed air storage in load-unload systems to avoid short cycling and reduce system energy use. First, key equations relating storage, pressure, and compressed air flow are derived using fundamental thermodynamic relations. Next, these relations are used to calculate the relation between volume of storage and cycle time in load-unload compressors. It is shown that cycle time is minimized when compressed air demand is 50% of compressor capacity. The effect of pressure drop between compressor system and storage on cycle …

Improving Compressed Air Energy Efficiency In Automotive Plants: Practical Examples And Implementation, Nasr Alkadi, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

The automotive industry is the largest industry in the United States in terms of the dollar value of production [1]. U.S. automakers face tremendous pressure from foreign competitors, which have an increasing manufacturing presence in this country. The Big Three North American Original Equipment Manufacturers (OEMs)-General Motors, Ford, and Chrysler-are reacting to declining sales figures and economic strain by working more efficiently and seeking out opportunities to reduce production costs without negatively affecting the production volume or the quality of the product. Successful, cost-effective investment and implementation of the energy efficiency technologies and practices meet the challenge of maintaining the …

The Effect Of Cryogenic Treatment On The Fatigue Life Of Chrome Silicon Steel Compression Springs, Debra Lynn Smith

Dissertations (1934 -)

The purpose of this dissertation is to explore the effect of cryogenic treatment on the fatigue life of compression springs. Product manufacturers are constantly searching for ways to make their products last longer. This dissertation addresses three questions: (1) What is the effect of cryogenic treatment on the fatigue life of chrome silicon steel compression springs? Does the life increase, decrease, or remain the same? (2) What is the effect of cryogenic treatment on the Percent Load Loss (Stress Relaxation) of chrome silicon steel compression springs? (3) What are the possible changes in the material that cause these effects?

The …

Geomagnetic Compensation For Low-Cost Crash Avoidance Project, John C. Torres

Master's Theses

The goal of this work was to compensate for the effects of the Earth’s magnetic field in a vector field magnetic sensor.  The magnetic sensor is a part of a low-cost crash avoidance system by Stephane Roussel where the magnetic sensor was used to detect cars passing when it was mounted to a test vehicle.  However, the magnetic sensor’s output voltage varied when it changed orientation with respect to the Earth’s magnetic field.  This limited the previous work to only analyze detection rates when the test vehicle travelled a single heading.  Since one of the goals of this system is …

A Novel Approach To The Part Orientation Problem For Robotic Assembly Applications, Brian James Slaboch

Master's Theses (2009 -)

SCARA (Selective Compliant Assembly Robot Arm) type robots are the most common type of assembly robots. These robots have four degrees of freedom (three rotational and one translational). Typically these robots are used for assembly tasks that take place along a vertical axis. Many times, however, assembly tasks take place along a non-vertical axis. To account for non- vertical axis assembly, parts must be fed in a proper orientation to allow for correct assembly. Parts feeders and specialized end-effectors are typically used to feed parts in their proper orientation. This thesis investigates a novel end-effector that can be used to …

Method Of Tolerance Allocation To Maintain Rotary Balance Of Multi-Component Bodies, Lindsay Louise Rogers

Master's Theses (2009 -)

Vibration of rotating machinery caused by mass imbalance is the most frequent source of unwanted disturbing forces and also the most preventable. In the case of a CT scanner, unwanted vibration in the equipment causes artifacts to the X-ray image, and therefore all measures are taken to eliminate imbalance. The CT scanner is a multi-component rotating body, therefore making it a challenge to account for many discrete components, each with unique variation. This research developed the equations for static and dynamic balance including considerations for inertia. The variation of the components was studied using two models: a sensitivity analysis and …

Optimal Mobile It Location Based On Ergonomics, Kyle Saginus

Master's Theses (2009 -)

U.S. and Canadian electric utility companies are in the process of integrating mobile computers into their fleet vehicle cabs. The placement of the mobile computer in the vehicle cab could have a significant effect on biomechanical loading, performance, and subjective assessment. The objective of this research is to determine the best location to place a mobile computer in a truck cab.

In this experiment, four locations of mobile computers in a truck cab were selected and tested in a laboratory study to determine how location affected muscle activity of the lower back and shoulders; joint angles of the shoulders, elbows, …

One-Dimensional Strain Initiated By Rapid Compaction Of A Heterogenous Granular Mixture Consisting Of Cu, Fe, Sio2, C, Mos2, And Sn, Cullen Braun

Master's Theses (2009 -)

The dynamic compaction of metal powders is of great interest to the metallurgical and military communities. The compaction of a heterogeneous granular mixture consisting of copper, iron, silica, graphite, molybdenum-disulde, and tin predominately used in aviation break-pad creation is presented. The initial density of the material was on average 2.756 g/cm3 . The research also required developing a working projectile velocity measurement system and a proper target assembly for pressure measurements. Manganin gages were used to record the shock wave transit time and the pressure of the transmitted waveform into the powder mixture. An impedance matching technique was utilized to …

A Pilot Model For Investigating Biodynamic Coupling Due To Aeroservoelastic Accelerations, Brandon Cowen

Mechanical & Aerospace Engineering Theses & Dissertations

Supersonic Transport Aircraft tend to have slender fuselages with respect to their subsonic counterparts. This design feature leads to increased aeroservoelastic bending at low resonant frequencies closer to the frequencies of pilot commands and the corresponding rigid body accelerations. Aeroelastic accelerations of certain frequencies and phase lags at the pilot station have been seen to involuntarily pass through the pilot's body to the control inceptor. When the pilot commands rigid body accelerations in phase with the structural response, the structural accelerations grow. Thus biodynamic coupling represents the coupling between the feedthrough of pilot station acceleration through the pilot's body, with …

Natural Gas As Petroleum Fuel Substitution: Analysis Of Supply-Demand Projections, Infrastructures, Investments And End-User Prices, Abdul Qoyum Tjandranegara, Arsegianto Arsegianto, Widodo Wahyu Purwanto

Makara Journal of Technology

The petroleum fuels (PF) subsidy has long burdens the government spending, and discourages less expensive energy usage such as natural gas (NG). Exporting NG and importing the more expensive PF products cause financial losses to Indonesia. The lack of NG infrastructure is the main hurdle in maximizing domestic NG usage and so does the perception of its high investment costs burdening government spending and pushing the NG transportation cost up. This study calculates the required NG infrastructure and its investments for several levels of PF substitutions up to 2030. To balance the NG demands, the supply from each field and …

The Synergy Of Recombinant Xylanolytic Enzyme On Xylan Hydrolysis, One Asmarani, Bambang Prajogo Eko Wardojo, Ni Nyoman Tri Puspaningsih

Makara Journal of Technology

Microbial xylanases or xylanolytic enzyme have received considerable attention over the last years owing to a multitude of possible applications. These enzymes have potential in the biodegradation of lignocellulosic biomass to fuels, chemicals, fruit juice, animal feed and in improving rumen digestion. More recently, the use of xylanases as bleaching agent in the pulp and paper industry has been suggested to replace of some of the chemicals presently used for this purpose. Such applications could have an important positive impact on the environment. The purpose of this research was determining the synergy of 3 recombinant xylanolytic enzymes (β-xylosidase, exo-xylanase and …

Cradle To Gate Simple Life Cycle Assessment Of Biodiesel Production In Indonesi, Akhmad Hidayatno, Teuku Yuri M. Zagloel, Widodo Wahyu Purwanto, Carissa Carissa, Lindi Anggraini

Makara Journal of Technology

The focus of this research is to analyze potential environmental impact in the supply chain of palm oil biodiesel industries. Simple Life Cycle Assessment (LCA) is applied to analyze impacts, produced by the three main units in the supply chain of Palm-Oil-based Biodiesel, which are Palm Plantation, CPO mill, and Biodiesel Plant. We developed LCA calculation model using spreadsheet software, used to assess a number of input scenarios to evaluate the best scenario, in variation of: land quality, land area and the rate of clearing, land clearing technique and type of the original land. The biggest potential environmental impact is …

Characterization Of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum Inophyllum Linn), Santiyo Wibowo, Wasrin Syafi, Gustan Pari

Makara Journal of Technology

Characterization of Surface Active Shell Charcoal Nyamplung Seeds (Calophyllum inophyllum Linn). Chemical and physical activation of nyamplung shell with 0%, 5%, and 10% H3PO4 for 60 and 120 minutes has been carried out to prepare activated charcoal. The purpose of this experiment was to look into the characteristic of nyamplung shell activated charcoal surface. Nyamplung shell was carbonized into charcoal, then activated by immersion in H3PO4 solution using 0%, 5% and 10%, for 24 hours, and heated in retort at two temperatures (700 and 800 oC) and two duration (60 and 120 minutes). The material were characterized by fourier transform …

An Investigation Into The Resistance/Powering And Seakeeping Characteristics Of River Catamaran And Trimarana, Murdijanto Murdijanto, I Ketut Aria Pria Utama, Andi Jamaluddin

Makara Journal of Technology

The increase of fuel price has caused fleet operational and shipping business to be in danger situation. The fuel consumption of a ship is influenced by ship volume or wetted area which contributes directly to the increase of ship resistance and the size of main engine. In order to find out the appropriate answers, a series of investigation into river transportation using monohull, catamaran and trimaran types of vessel was carried out. The work focused on the estimation of total resistance and powering as well as seakeeping characteristics and carried out experimentally using tank test and numerically using a ship …