Mechanical Engineering Commons^™

Modeling And Control Of Freeze-Form Extrusion Fabrication, Xiyue Zhao

Masters Theses

"Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing technique that extrudes ceramic loaded aqueous pastes layer by layer below the paste freezing temperature for component fabrication. As the FEF is aimed at being conducted at low environmental temperatures, down to -20°C, it is necessary to investigate the effect of environmental temperature on the process. The advantages of fabrication at low temperature have been proved by experiments. Comparisons in terms of operation parameters, self-sustaining ability, and system dynamic response were performed at different environmental temperatures ranging from 20°C to -20°C.

It is commonly known in paste extrusion processes that due to …

Accelerated Testing Method For Pem Fuel Cell Based Uninterrupted Power Supply Systems, Xinyu Huang, Xiaofeng Wang

Faculty Publications

Proton exchange membrane fuel cell based power systems are on the verge of commercialization for a number of niche applications where batteries are traditionally used. Uninterrupted power supply (UPS) for wireless communication towers and broadband network relay utilities is one of the targeted application of fuel cell power systems with capacity ranging from one to serveral kilowatts. It is believed that fuel cell based UPS systems can offer considerable advantage when extended backup time is desirable. In order to replace the well-known battery based UPS systems, the reliability and perofrmance of fuel cell based UPS system need to be thoroughly …

Short-Term Reliability Of A Thin Film Resistance Temperature Detector (Rtd), Julian W. Post, Jr.

Theses and Dissertations

The primary focus of this dissertation was on the short term reliability of a thin film resistance temperature detector (RTD). As a first step, the transient and steady state temperature response of an encapsulated, thin-film RTD, which was used as a micro heater, have been characterized for a range of pressures and applied voltages, while placed on thermally insulating and conductive platforms. A user-friendly model was used to capture the three major mechanisms of heat transfer from the device (i.e. conduction, convection, and radiation). The calibration parameters of the model allowed the different modes of heat transfer to be quantified. …

Selective Laser Sintering Of Stearic Acid-Coated Alumina Ceramic, Jason J. Nolte

Masters Theses

"The purpose of this research is to develop a process that will enable a Selective Laser Sintering (SLS) machine to create geometrically complex green parts of various sizes that become strong, dense ceramic parts after sintering. This will be applicable to SLS systems already operational in industry, and may offer a more cost-effective, more time-efficient method for producing high-temperature ceramic rapid prototype parts. Alumina was the chosen ceramic for the developmental stage of this research. Fine alumina powder (average particle size of 0.4 µm) was coated with stearic acid, which served as a binder. Green parts were made from this …

Development, Modeling, And Simulation Of A Nano Aerial Vehicle Using Empirical Data, Wyatt Emery Davenport

Masters Theses

"The ultimate goals of this study were to use experimental data to estimate the flight capabilities of a flapping wing nano aerial vehicle (NAV), estimate the power required to provide such flight, and develop a controller approach for future use in the design of this aircraft. The experimental data is a collection of measurements of the normal force on a flapping wing taken in stationary water, and was used to develop empirical coefficient derivatives for use in the dynamic modeling of the NAV"--Abstract, page iii.

Robust Mechanism Synthesis With Random And Interval Variables, Pavan Kumar Venigella

Masters Theses

"Robust mechanism synthesis ensures that the performance of a mechanism is not sensitive to uncertainties in the mechanism and its environment. The uncertainties include the dimension variations, installation errors, random input motion, and various external forces. Robust mechanism synthesis is used to minimize the impact of these uncertainties on the mechanism performance. Robust mechanism synthesis has been performed by either a probabilistic approach or a worst case approach. The former approach describes uncertain parameters as random variables while the latter approach treats uncertain parameters as interval variables. In this work, methods are developed for robustness assessment and robust mechanism synthesis …

Meso-Machining Of Miniature Space System Components, Carlos Ramirez

Open Access Theses & Dissertations

Many industries in engineering and science are focusing more on producing mechanisms and system components of magnitudes smaller than existing products. One of the major technologies associated with these demands is the development of meso scale precision manufacturing systems. Meso scale fabrication involves the scaling down of conventional machining to incorporate the use of familiar materials, such as aluminum, steel, and even titanium for machining miniature components. New techniques in meso scale fabrication allow for the machining of miniature space system components in an efficient manner to meet certain specifications. A description of the processes used to accurately machine a …

An Investigation Of The Frictional And Thermal Behavior Of Oscillatory Sliding Line Contacts, Mongi Mansouri

LSU Doctoral Dissertations

This research deals with an experimental and numerical investigation of the frictional and thermal behavior of pin-bushing pairs, operating at reciprocating sliding motion or under heavy loads. Large interfacial temperatures developed due to frictional heating can cause failure. Therefore, numerical prediction and analysis of the surface temperature under various operating conditions are important. Laboratory tests using a pin-bushing tester provided measurements of the friction coefficient and temperature. Hard coated and plain (uncoated) bushings, both made of induction hardened stainless steel, were tested. Lower coefficient of friction and surface temperature were observed in the case of the coated bushing. In the …

Eigenvalue Optimization And Its Applications In Buckling And Vibration, Srinivas Gopal Krishna

LSU Doctoral Dissertations

Eigenvalue problems are of immense interest and play a pivotal role not only in many fields of engineering but also in pure and applied mathematics. An in-depth understanding of this class of problems is a pre-requisite for vibration and buckling analyses of structures. Design optimization of structures to prevent failure due to instability (bucking) and vibration introduces the problem of determining optimal physical parameters such that load carrying capacity or the fundamental natural frequency is maximized. A classical example of such problems is the Lagrange problem of determining the shape of the strongest column against buckling. The primary objective of …

Thermal Effectiveness Characteristics Of Low Approach Indirect Evaporative Cooling Systems In Buildings, Ben Costelloe, Donal Finn

Articles

Meteorological enthalpy analysis of temperate and maritime climates above latitude 45°N suggests that the water-side evaporative cooling technique has considerable unrealised potential with contemporary “high temperature” building cooling systems—such as chilled ceilings and displacement ventilation. As low approach conditions are the key to exploiting the cooling potential of the ambient air, thermal performance at such conditions needs to be investigated. To address the research issues, an industrial scale test rig, based on a low approach open cooling tower and plate heat exchanger and designed to maximise evaporative cooling potential, has been constructed. The thermal effectiveness of such systems (as a …

Characterization And Flow Physics Of Plasma Synthetic Jet Actuators, Arvind Santhanakrishnan

University of Kentucky Doctoral Dissertations

Plasma synthetic jet actuators are investigated experimentally, in which the geometrical design of single dielectric barrier discharge (SDBD) plasma actuators is modified to produce zero-mass flux jets similar to those created by mechanical devices. The SDBD plasma actuator consists of two rectangular electrodes oriented asymmetrically and separated by a layer of dielectric material. Under an input of high voltage, high frequency AC or pulsed DC, a region of plasma is created in the interfacial air gap on account of electrical breakdown of the ambient air. A coupling between the electric field in the plasma and the neutral air near the …

Capacitance Metrology Of Curved Surfaces: Study And Characterization Of A Novel Probe Design, Philip T. Smith Jr.

University of Kentucky Doctoral Dissertations

Capacitive sensors are frequently applied to curved target surfaces for precision displacement measurements. In most cases, these sensors have not been recalibrated to take the curvature of the target into consideration. This recalibration becomes more critical as the target surface becomes smaller in comparison to the sensor. Calibration data are presented for a variety of capacitance probe sizes with widely varying geometries. One target surface particularly difficult to characterize is the inner surface of small holes, less than one millimeter in diameter. Although contact probes can successfully measure the inner surface of a hole, these probes are often fragile and …

Compliant High-Precision E-Quintet Ratcheting (Cheqr) Mechanism For Safety And Arming Devices, John A. Kennedy, Larry L. Howell, William Greenwood

Faculty Publications

Ratchet and pawl mechanisms are used in safety applications to provide mechanical isolation between inputs and an output to insure that extreme environmental conditions do not inadvertently allow an unexpected output. These devices have become smaller and are approaching a size regime where traditional precision components, such as precision bearings and springs, are not available. This paper introduces the Compliant High-precision E-Quintet Ratcheting (CHEQR) mechanism as a means of exploiting the advantages of compliant mechanisms to create safety devices that eliminate the need for bearings and springs. The pseudo-rigid-body model was used to design a mechanism with the desired force-deflection …

Thermal Control Of An Occupied Room: Investigating The Use Of Carbon Dioxide Concentration As An Auxiliary Control Variable, Kevin O'Connell, Aidan O'Dwyer

Conference papers

This paper details the theoretical and experimental work done in the examination of the relationship between human generated carbon dioxide concentration and temperature rise in an occupied room. Generation of carbon dioxide by humans is linked to metabolic rate and heat generation. Therefore, carbon dioxide concentration may be used as an indicator of occupancy in a room. Typically, a heating control system will react slowly to changes in room occupancy if temperature is used as the process variable. The aim of the work was to establish if carbon dioxide concentration in the space could be used as an auxiliary control …

Measurements And Computations Of The Flow In Full-Scale Sugar Evaporative-Crystallizers And In Lab-Scale Models, Luis Fernando Echeverri

LSU Doctoral Dissertations

The circulation of massecuite is a key factor in achieving efficient heat transfer and crystallization in sugar evaporative crystallizers, and should be as high as practically possible for recovery, quality, and capacity reasons. This research report presents results on the circulation obtained applying modern experimental and numerical techniques. The main goals are contributing to expand the understanding of the process in sugar crystallizers; developing realistic models for the simulation of the circulation; and studying the effect of different design parameters. The circulation of massecuite is driven by buoyancy force due to density difference between the vapor generated and the surrounding …

Computational Study Of Laminar Separation Bubble Development Over Supersonic Airfoils At Subsonic Speeds, Josiah D. Elliott

Opportunities for Undergraduate Research Experience Program (OURE)

Laminar Separation Bubbles (LSBs) are regions of separated flow that start near the leading edge of an airfoil and reattach further down the airfoil surface. These regions of separation can appear at low angles of attack and can grow significantly as the angle of attack is increased heavily influencing the flow characteristics over the airfoil. Research on this topic is driven by the supersonic business jet industry which has a particular interest in this type of research due to performance requirements in both the subsonic and supersonic flight regimes. This manuscript is focused on the flow developments near the sharp …

In-Situ Optimized Pwas Phased Arrays For Lamb Wave Structural Health Monitoring, Lingyu Yu, Victor Giurgiutiu

Faculty Publications

No abstract provided.

Dynamics Of Wave-Current Boundary Layers Over Very Rough Boundaries, Marion Bandet-Chavanne

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

In this study, acoustic profiling techniques are used to resolve the two-dimensional spatial structures of the oscillating boundary layer in a phase-averaged sense over a wave orbital amplitude. The principal objective of this work is to examine the spatial variability of turbulent properties over irregular roughness. Field observations are used to investigate the interaction between bottom roughness, flow structure and turbulent properties within the near-bed flow. The overall focus of the research is to relate wave energy dissipation or friction factor estimates to physical roughness elements and understand the dynamics of such processes in the near-bed flow.

Semi-Autonomous Control Of Autonomous Underwater Vehicles, Stephen C. Martin

Link Foundation Ocean Engineering and Instrumentation Fellowship Reports

The goal of my graduate research is to address two engineering science problems whose solution will enable Autonomous Underwater Vehicles (AUVs) to routinely perform semi-autonomous missions presently considered impractical or infeasible. I am pursuing this research under the direction of Professor Whitcomb in the Dynamical Systems and Controls Laboratory at Johns Hopkins University, and in collaboration with the faculty of the Deep Submergence Laboratory of the Woods Hole Oceanographic Institution (WHOI).

In the last decade AUVs have begun to complement Human Occupied Vehicles (HOVs) and Remotely Operated Vehicles (ROVs) as effective platforms for oceanographic exploration. HOVs and ROVs are highly …

Regional Mechanical Properties And Stress Analysis Of The Human Anterior Lens Capsule, Ryan M. Pedrigi, G. David, J. Dziezyc, J. D. Humphrey

Department of Mechanical and Materials Engineering: Faculty Publications

The lens capsule of the eye functions, in part, as a deformable support through which the ciliary body applies tractions that can alter lens curvature and corresponding refractive power during the process of accommodation. Although it has long been recognized that characterization of the mechanical properties of the lens capsule is fundamental to understanding this physiologic process as well as clinical interventions, prior data have been limited by one-dimensional testing of excised specimens despite the existence of multiaxial loading in vivo. In this paper, we employ a novel experimental approach to study in situ the regional, multiaxial mechanical behavior of …

A Scientific Foundation Of Collaborative Engineering, S. C.-Y. Lu, W. Elmaraghy, G. Schuh, R. Wilhelm

Department of Mechanical and Materials Engineering: Faculty Publications

Collaborative engineering is the practical application of collaboration sciences to the engineering domain. In today’s highly connected technology-driven economy, the production industry must rely on the best practices of collaborative engineering to stay competitive when designing, manufacturing, and operating complex machines, processes, and systems on a global scale. Despite its importance, collaborative engineering is currently more of a practiced art than a scientific discipline. A better understanding of how engineers should collaborate with all stakeholders to accomplish complex tasks that fulfill our increasing social responsibilities is a grand challenge. However, because we currently lack well-defined sciences of human collaboration, we …

Origin Of Photomultiplication In C60 Based Devices, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this manuscript, the origin of the photomultiplication effect was studied in C₆₀ based devices by evaluating the wavelength dependent external and internal quantum efficiencies under various biases. The effect of materials with disordered structures on the photomultiplication effect was determined by intentionally integrating both ordered and disordered material structures into one organic solar cell device with a configuration of indium tin oxide/poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS)/pentacene/C₆₀ fullerene/bathocuproine (BCP)/Al. Our results show that both the disordered structure of C₆₀ and the charge trapping effect at the C₆₀ /PEDOT:PSS interface contribute to the photomultiplication effect. By studying the C60-only …

Low Voltage And Fast Speed All-Polymeric Optocouplers, Yan Yao, Hsiang-Yu Chen, Jinsong Huang, Yang Yang

Department of Mechanical and Materials Engineering: Faculty Publications

An all-polymeric optocoupler has been demonstrated with a polymer light-emitting diode (PLED) as the light source (input unit) and a polymer/fullerene photodiode (PD) as the detector (output unit). The electroluminescence (EL) peak of the PLED is 560 nm, and the entire EL spectrum is within the response range of the PD. The optocoupler can work at low driving voltages, 5 V on the PLED and 0 V on the PD. The output photocurrent increases linearly with input current, and the current density transfer ratio reaches 1.5%. The frequency response of the optocoupler is at 500 kHz. With comparable performance to …

Method And System For Far-Field Microscopy To Exceeding Diffraction-Limit Resolution, C. Ya, Hai-Lung Tsai

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The bio-sample (e.g., a live cell) is labeled with a proper number of nanoparticles. Each nanoparticle is pre-co-doped with a controlled ratio of fluorophore donors and acceptors. Two laser pulses are applied to the bio-sample. The first laser pulse has a center wavelength near the peak of absorption spectrum of acceptors. The intensity of first laser pulse is adjusted such that FRET saturation occurs near the center of the focal spot. The focal spot of the first laser pulse is a diffraction-limited Airy disk that has the highest laser intensity in the center of the focal spot. The second laser …

Optimal Neuro-Controller Synthesis For Impulse-Driven System, Xiaohua Wang, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a new controller design technique for systems driven with impulse inputs. Necessary conditions for optimal impulse control are derived. A neural network structure to solve the resulting equations is presented. The solution concepts are illustrated with a few example problems that exhibit increasing levels of difficulty. Two linear problems-one scalar and one vector-and a benchmark nonlinear problem-Van Der Pol oscillator-are used as case studies. Numerical results show the efficacy of the new solution process for impulse driven systems. Since the theoretical development and the design technique are free from restrictive assumptions, this technique is applicable to many …

Method And Apparatus For Improved Cooling Of Restistance Welding Cap, M. J. Karagoulis, R. Stevenson, Hai-Lung Tsai, P.-C. Wang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

According to the invention a hollow cylindrical shank of electrically conducting metal is connected to a resistance welder. A coolant supply tube passes through the shank and has an interior coolant supply passage. The coolant supply tube has an outer diameter less than the inner diameter of the hollow cylindrical shank. A weld cap seats on the shank and has a cap tip and a cap skirt that depends from the cap tip and is attached to the shank. An underside of the cap tip faces the shank and the supply tube. A coolant receiving bore formed into the underside …

Acoustic Emission Detection And Prediction Of Fatigue Crack Propagation In Composite Patch Repairs Using Neural Networks, Navdeep Singh, Navrag Singh, Anthony Chukwujekwu Okafor

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An aircraft is subjected to severe structural and aerodynamic loads during its service life. These loads can cause damage or weakening of the structure especially for aging military and civilian aircraft, thereby affecting its load carrying capabilities. Hence composite patch repairs are increasingly used to repair damaged aircraft metallic structures to restore its structural efficiency. This paper presents the results of Acoustic Emission (AE) monitoring of crack propagation in 2024-T3 Clad aluminum panels repaired with adhesively bonded octagonal, single sided boron/epoxy composite patch under tension-tension fatigue loading. Crack propagation gages were used to monitor crack initiation. The identified AE sensor …

Simple Penning Ion Source For Laboratory Research And Development Applications, Joshua L. Rovey, Brandon P. Ruzic, Thomas J. Houlahan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A simple Penning ion generator (PIG) that can be easily fabricated with simple machining skills and standard laboratory accessories is described. The PIG source uses an iron cathode body, samarium cobalt permanent magnet, stainless steel anode, and iron cathode faceplate to generate a plasma discharge that yields a continuous 1 mA beam of positively charged hydrogen ions at 1 mTorr of pressure. This operating condition requires 5.4 kV and 32.4 W of power. Operation with helium is similar to hydrogen. The ion source is being designed and investigated for use in a sealed-tube neutron generator; however, this ion source is …

A Computational Theory For The Generation Of Solutions During Early Conceptual Design, Cari R. Bryant

Doctoral Dissertations

"Advancement in technology is usually made by building on previous experiences and learning from past successes and failures. However, knowledge transfer in the broad field of product design is often difficult to accomplish. Research has shown that successful component configurations, observed from existing products, can be dissected and stored for reuse; but few computational tools exist to assist designers during the conceptual phase of design. Many well-known manual methods (e.g. brainstorming, intrinsic and extrinsic searches, and morphological analysis) rely heavily on individual bias and experience and are often time intensive, laborious tasks that may not catch solutions that are functionally …

Experimental Investigation Of Temperature And Tool Wear In High Speed End-Milling Of Titanium Alloy, Benjamin Nwakile Oguejiofor

Masters Theses

"This thesis presents the results of experimental investigation of temperature and tool wear in high speed end-milling of titanium alloy. The investigation of cutting parameters on temperature in high speed end-milling of thin-walled titanium structure was conducted on Cincinnati Milacron Sabre 750 Vertical Machining Center using a 1/2 Fractional Factorial Design of Experiment with 3 factors at 2 levels each. Data logging of temperature data was carried out using VI logger software. Tool tip temperature at the comers and center of the pocket was estimated. All the factors investigated were found to have a significant effect on workpiece temperature. Radial …