Mechanical Engineering Commons^™

Output Feedback Force Control For A Parallel Turning Operation, Raghusimha Sudhakara, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Parallel machine tools (i.e., machine tools capable of cutting a part with multiple tools simultaneously but independently) are being utilized more and more to increase operation productivity, decrease setups, and reduce floor space. Process control is the utilization of real-time process sensor information to automatically adjust process parameters (e.g., feed, spindle speed) to increase operation productivity and quality. To date, however, these two technologies have not been combined. This paper describes the design of an output feedback controller for a parallel turning operation that accounts for the inherent nonlinearities in the force process. An analysis of the process equilibriums explains …

Intelligent Strain Sensing On A Smart Composite Wing Using Extrinsic Fabry-Perot Interferometric Sensors And Neural Networks, Kakkattukuzhy M. Isaac, Donald C. Wunsch, Steve Eugene Watkins, Rohit Dua, V. M. Eller

Electrical and Computer Engineering Faculty Research & Creative Works

Strain prediction at various locations on a smart composite wing can provide useful information on its aerodynamic condition. The smart wing consisted of a glass/epoxy composite beam with three extrinsic Fabry-Perot interferometric (EFPI) sensors mounted at three different locations near the wing root. Strain acting on the three sensors at different air speeds and angles-of-attack were experimentally obtained in a closed circuit wind tunnel under normal conditions of operation. A function mapping the angle of attack and air speed to the strains on the three sensors was simulated using feedforward neural networks trained using a backpropagation training algorithm. This mapping …

Vibration-Based Crack Diagnosis In Rotating Shafts During Acceleration Through Resonance, Jerzy T. Sawicki, Xi Wu, George Y. Baaklini, Andrew L. Gyekenyesi

Mechanical Engineering

The dynamic response of a cracked Jeffcott rotor passing through the critical speed with constant acceleration is investigated analytically and numerically. The nonlinear equations of motion are derived and include a simple hinge model for small cracks and Mayes' modified funciton for deep cracks. The equations of motion are integrated in the rotating coordinate system. The angle between the crack centerline and the shaft vibaiton (whirl) vector is used to determine the clsoing and opening of the crack, allowing one to study the dynamic response with and without the rotor weight dominance. Vibration phase response is used as one of …

An Experimental Investigation Of Whirl Instability Including Effects Of Lubricant Temperature In Plain Circular Journal Bearings, Darryl, Jr. Chauvin

LSU Master's Theses

The purpose of this thesis is to experimentally investigate the effect of lubricant temperature on the presence of whirl instability in journal bearings. The first set of conditions that are studied is an extremely low eccentricity rotor and the occurrence of oil whirl at the start-up of the experiment. Lubricant temperature, bearing temperature, frequency and amplitude of vibration, and rotational speed are monitored and analyzed in relation to presence of whirl instability. Additionally, another rotor with a slightly higher eccentricity is tested with respect to the presence of such instability. Particularly with this rotor, the system is brought just below …

Nebraska Summary: S305 Challenger Mt 545, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S558 Massey Ferguson 5465, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1826: Case Ih Mx 230 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1832: New Holland Tg 285 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1823: Challenger Mt 835 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Nebraska Summary S360a: Challenger Mt 445, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 412: Fendt 412 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 440: Fendt 712 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 443: John Deere 6415 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 558: Massey Ferguson 5465 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Analytical And Fea Analysis Of Silicon Micro-Machined Capacitive Pressure Sensor, Eoghan O'Donoghue

Theses

This thesis is concerned with the electro-mechanical characterisation of MEMS capacitive pressure sensors and the determination of models to describe their behaviour.

The finite element software package ANSYS is validated as a tool for the examination of the electro-mechanical behaviour of capacitive pressure sensors. It is then used to incorporate the effects of applied load, voltage and residual stress into a model of the sensor structure. The capacitive pressure sensor is modelled both in 3D and also in 2D axis-symmetric modes. The error between the 2D and 3D models is quantified.

The behaviour of structures under electrostatic actuation is investigated. …

Structure And Mechanical Properties Of Ti-Si-N Coatings, Xiaodong Zhang

LSU Master's Theses

In order to better define conditions under which ~{!0~}super-strengthening~{!1~} occurs in the Ti-Si-N system, we performed detailed experimental studies on how the structure and mechanical properties of Ti-Si-N coatings are influenced by the deposition temperature. Different series of Ti-Si-N specimens were prepared in an inductively coupled plasma (ICP)-assisted reactive sputtering system at both low and high temperatures. Coating compositions were measured by Rutherford backscattering spectrometry (RBS) technique, surface roughness was examined on an atomic force microscope (AFM), coating thicknesses were obtained by performing cross-sectional scanning electron microscopy (SEM), and their structure examined with transmission electron microscopy (TEM). Vibrational frequency results …

A Disjoining Pressure For Small Contact Angles And Its Applications, Qingfang Wu

LSU Master's Theses

A thin liquid film experiences additional intermolecular forces when the film thickness h is less than roughly 100 nm. The effect of these intermolecular forces at the continuum level is captured by the disjoining pressure . Since dominates at small film thicknesses, it determines the stability and wettability of thin films. To leading order, a thin film can be treated as uniform and . This form, however, cannot be applied to films with non-zero contact angles. A recent ad-hoc derivation to include the slope leads to a that allows a contact line to move without slip. This work derives a …

Thermohydrodynamic Analysis Of Compressible Gas Flow In Compliant Foil Bearings, Zhengchun Peng

LSU Master's Theses

This thesis deals with the development of mathematical models and numerical schemes for simulating the hydrodynamic pressure and temperature rise of compliant foil bearings lubricated by a thin gas film in between its compliant bearing surface and the rotating shaft. The model accounts for the compressibility of gas, the compliance of the bearing surface, and the interaction between the pressure field and temperature field of the gas film in the bearing system. Numerical solutions obtained over a fairly large range of operating speeds show excellent agreement with existing experimental data from both load performance test and bearing temperature measurement. A …

Precipitate Growth Features In The Duplex Size Gamma Prime Distribution In The Superalloy In738lc, Indranil Roy

LSU Master's Theses

IN738LC is a modern, nickel base superalloy utilized at high temperatures in aggressive environments. Durability of this superalloy is dependent on the retention of strengthening by Gamma Prime precipitates. The precipitate growth features in the duplex size (fine and coarse) precipitate distribution was studied by heating the alloy for various times in vacuum at selected temperatures in the range 800 °C to 1100 °C. Increasing the holding times from 1 hour to 100 hours shows joining of the fine particles to form bigger particles, leading to distinct raft patterns. Two different Gamma Prime precipitate growth processes had been observed: merging …

Axis-Switching In Square Coaxial Jets, Victor Piffaut

LSU Master's Theses

Airflow from single and coaxial contoured nozzles with a square cross section is studied using constant temperature anemometry. The inner to outer jet velocity ratio is 1.5. The Reynolds number of the outer jet based on the hydraulic diameter of the outer nozzle exit is 15,300. Results are compared to previous data obtained with circular nozzles under the same conditions. Properties of the jets and their shear layers such as turbulence shear layer thicknesses and growth rates were derived from the velocity record. The mixing between the jets and with the external flow was found to be enhanced by passive …

Effect Of Jet Hole Arrays Arrangement On Impingement Heat Transfer, Lujia Gao

LSU Master's Theses

A comprehensive investigation on impingement heat transfer of different jet array arrangements is presented. Experiments on the inline jet arrays and the linearly stretched arrays are performed using transient liquid crystal technique. Three experimented basic inline jet arrays are configurations 4X4, 8X4 and 8X8. Two experimented cases for the linearly stretched arrays are the uniform diameter case and the varying diameter case. For the inline jet arrays, three jet heights Z/D=1, 3 and 5 and three Reynolds numbers Re=5000, 10000 and 15000 are investigated. For linearly stretched arrays, the same three jet heights and Re=2000, 6000 and 10000 are investigated. …

Evaluation Of Mechanical Fitness For Service Of High Temperature Hydrogen Attacked Steels, Brent Matthew Saba

LSU Master's Theses

A novel approach is introduced in evaluating one of industry’s most complex corrosion phenomena, high temperature hydrogen attack (HTHA). Limited efforts have been made by industry to address this degradation mechanism and even less data are available to properly utilize their evaluation techniques. The predominant fracture mechanics based analysis of HTHA relies on Charpy V-Notch (CVN) impact test data. In the face of limited CVN test data, accurate results are shaky at best. The HTHA evaluation set forth in this paper combines the analysis tools of plastic collapse and both static and dynamic fracture mechanics. The first condition addresses plastic …

Effect Of Unsteady Wake, Free Stream Turbulence, Tip Geometry On Blade Tip Flow And Heat Transfer, Vikrant Saxena

LSU Master's Theses

A comprehensive investigation of the effect of various tip sealing geometries is presented on the blade tip leakage flow and associated heat transfer. The linear cascade is made of four blades scaled up HPT turbine in a low speed wind tunnel facility with the two corner blades acting as guides. The tip section of a HPT first stage rotor blade is used to fabricate the 2-D blade. The wind tunnel accommodates an 116 degree turn in the flow through the blade cascade. The mainstream Reynolds number based on the axial chord length at cascade exit is 4.83e5. The center blade …

Predictions For Multi-Scale Shock Heating Of A Granular Energetic Material, Venugopal Jogi

LSU Master's Theses

This thesis addresses the multi scale heating of a granular energetic solid due to shock loading. To this end, an existing mathematical model that has been used to predict low pressure bulk and localized heating of the granular high-explosive HMX ([CH₂NNO₂]₄) is extended to account for compressibility and melting of the pure phase solid. Dense granular HMX has a heterogeneous structure composed of randomly packed small grains (average size ~ 100 µm) having a free-pour density that is approximately 65% of the pure phase solid density. The shock loading response of this material is …

Film Cooling From Cylindrical Holes In Transverse Slots, Mohammed Altorairi

LSU Master's Theses

In this study, heat transfer coefficient and film effectiveness distributions are investigated for a film cooling hole configuration that has inclined holes discharging into a tangential slot before interactions with the mainstream. The cylindrical holes are inclined 35° along the mainstream direction. The effect of coolant-to-mainstream blowing ratio is examined for M=0.5 and M=1.0. Different slot width to hole ratios and also the effect of hole exit condition (square edge and triangular edge) is considered. The mainstream velocity and free-stream turbulence intensity in the low speed wind tunnel are 9 m/s and 7% respectively and the mainstream Reynolds number based …

Numerical Solution Of Ocular Fluid Dynamics, Satish Kumar

LSU Master's Theses

Numerical calculations of the aqueous humor dynamics in the anterior chamber of both the rabbit and the human eye are presented to delineate the basic flow and transport mechanisms. The calculations are based on a geometrical model of the eye, which represents the Trabecular mesh (TM) as a multi-layered porous zone of specified pore sizes and void fraction. Buoyancy is observed to be the dominant driving mechanism for the convective motion in both orientations (horizontal and vertical) of the eye. Reducing the TM pore size does not appear to have a significant influence on the intra-ocular pressure (IOP) until the …

The Transcendental Eigenvalue Problem And Its Application In System Identification, Kumar Vikram Singh

LSU Doctoral Dissertations

An accurate mathematical model is needed to solve direct and inverse problems related to engineering analysis and design. Inverse problems of identifying the physical parameters of a non-uniform continuous system based on the spectral data are still unsolved. Traditional methods, for the system identification purpose, describe the continuous structure by a certain discrete model. In dynamic analysis, finite element or finite difference approximation methods are frequently used and they lead to an algebraic eigenvalue problem. The characteristic equation associated with the algebraic eigenvalue problem is a polynomial. Whereas, the spectral characteristic of a continuous system is represented by certain transcendental …

Nebraska Summary 442: Fendt 716 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Test 2088: Case Ih Mxm130 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Entrainment Of Electrical Activation By Spatio-Temporal Distributed Pacing During Ventricular Fibrillation, Yiping Gu

University of Kentucky Master's Theses

Spatio-temporal variation in action intervals during ventricular fibrillation (VF) suggestthat the excitable gap may also be distributed spatio-temporally. The observation leadus to hypothesize that distributed pacing can be used to modify and entrain electricalactivation during VF. We tested this hypothesis using simulated VF and animal studies.

We simulated VF in a 400 by 400 cell matrix. Simulation results showed that activationpattern could be entrained using spatially distributed stimulation. Up to a certain limit,increasing stimulus strength and density led to improved entrainment. Best entrainmentwas obtained by pacing at a cycle length similar to the intrinsic cycle length.

In order to verify …