Mechanical Engineering Commons^™

Teaching Factory, Sema E. Alptekin, Reza Pouraghabagher, Patricia Mcquaid, Daniel Waldorf

Industrial and Manufacturing Engineering

Academia must develop a new approach to teaching in order to better prepare engineering students to function efficiently and adjust readily within the framework of the factories in the real world. Some engineering programs emphasize theory, while others emphasize application as isolated blocks. The "Teaching Factory" being developed at Cal Poly combines both theory and applications. It makes use of state-of-the-art industrial grade production equipment, computer hardware and software in the form of the following two systems: 1) a functioning "real" factory hardware environment, and 2) a Production Planning and Control Center.

Typical Photovoltaic System For A Commercial Building, Florida Solar Energy Center, Gobind Atmaram

FSEC Energy Research Center®

This paper covers the design and installation of an 11 peak kilowatt (kWp) grid-connected photovoltaic system on the roof of the new facilities at the Florida Solar Energy Center (FSEC7). The main objectives of this work are to demonstrate the application of photovoltaics (PV) as a demand-side management option for meeting peak commercial electric loads and provide a typical PV array and system design for commercial buildings. The PV array consists of 48 ASE America=s EFG ribbon silicon modules and is interfaced with three Omnion 4kW power conditioners. The complete array and system electrical design and installation were performed by …

Cooperative Control Of Uav Rendezvous, Timothy W. Mclain, Phillip R. Chandler, Steven Rasmussen, Meir Pachter

Faculty Publications

The cooperative control of timing and synchronization of tasks of multiple unmanned air vehicles (UAVs) represents a valuable capability for a wide range of potential multi-UAV missions. This research addresses the specific problem of cooperative rendezvous in which multiple UAVs are to arrive at their targets simultaneously. The development of a rendezvous manager state machine and a cooperative control decomposition approach are described. Simulation results demonstrating the feasibility of the approach are presented.

Effects Of Nox And Α-Fe2o3 On Mercury Transformations In A 7-Kw Coal Combustion System, Kevin C. Galbreath, Christopher J. Zygarlicke, Donald L. Toman, Richard L. Schulz

EERC Publications, Papers, & Presentations

In this investigation, the effects of NO₂ and α-Fe₂O₃ on Hg speciation were evaluated by injecting them into coal combustion flue gases produced from burning bituminous, subbituminous, and lignitic coals in a 7-kW combustion system.

Parametric Study Of Heavy Metal Partitioning In A Pilot Scale Incinerator Burning Simulated Municipal Solid Waste, Sukrut S. Thipse

Dissertations

Incineration is a combustion process used to convert toxic waste to benign gases and residue in presence of excess air. The products of the incineration process are bottom ash, fly ash and the flue gas. Most of the metal-based phases formed in incineration are toxic and their emissions need to be strictly controlled. Therefore, behavior of metal species during incineration must be well understood. Such understanding is possible based on the experimental identification of the metal phases formed in the waste combustion and determination of their concentration in various incineration products.

A pilot-scale incinerator of 140,000 Btu/hr capacity was constructed, …

Force And Effort Analysis Of Unfastening Actions In Disassembly Processes, Manuela Sonnenberg

Dissertations

Fastening is the process of connecting one or more parts together with the aid of fastening elements. Unfastening, the reverse of fastening, is the process of separating components from each other by removing or detaching fastening elements. So far, the unfastening process is not well understood, and the analysis about it is not very extensive.

However, the need for disassembly is currently increasing. First, parts have to be taken apart for service and repair, and secondly, for the recycling process. Therefore, there is a need to consider unfastening during the design process in order to enable efficient disassemblies.

The purpose …

Determination Of Statistical Characteristics Of Isotropic Turbulence, Tatiana A. Andreeva, William W. Durgin, F. J. Weber, Hamid Johari

Office of the Provost Scholarship

Ultrasonic flow measurement technology has the potential to significantly improve flow measurement accuracy beyond that presently achieved. However, current applications fail to achieve theoretical accuracies because of turbulence effects on ultrasonic wave transit time. Herein, the ultrasonic flowmeter equation is reconsidered, where the effects of turbulent velocity and sound speed fluctuations are included. The result is an integral equation for the corresponding correlation functions. In this paper experimental velocity data are used to solve this integral equation analytically. As a result, some statistical characteristics of the turbulent flow are developed and can explain the limitations of measurement accuracy observed in …

Ultrasonic Beam Propagation In Turbulent Flow, William W. Durgin, F. J. Weber, Hamid Johari

Office of the Provost Scholarship

A study was conducted to examine how a coherent sound burst, such as those used in an ultrasonic flowmeter, crosses a turbulent flow field. Many ultrasonic flowmeters use a time of flight method to determine the mean flow. This measurement method sends sound waves at some angle across a velocity field between two transducers, and the time required for the sound burst to cross this distance is measured on the order of nanoseconds. The system then reverses so that the sound wave burst is sent in the opposite direction. Knowing the distance traveled, the local average sound speed, and the …

Fsec Procedure For Testing Stand-Alone Photovoltaic Systems, Florida Solar Energy Center

FSEC Energy Research Center®

This procedure is based on IEEE P1526/D1, Draft Recommended Practice for Testing the Performance of Stand-Alone Photovoltaic Systems. The system performance is based upon how well it can charge the battery. The usable battery capacity is measured by charging and discharging the battery three separate times. The tests are designed to test the overall system performance in the span of about one month.

Cluster Monte Carlo Simulations Of The Nematic--Isotropic Transition, Nikolai V. Priezjev, Robert A. Pelcovits

Mechanical and Materials Engineering Faculty Publications

We report the results of simulations of the three-dimensional Lebwohl-Lasher model of the nematic-isotropic transition using a single cluster Monte Carlo algorithm. The algorithm, first introduced by Kunz and Zumbach to study two-dimensional nematics, is a modification of the Wolff algorithm for spin systems, and greatly reduces critical slowing down. We calculate the free energy in the neighborhood of the transition for systems up to linear size 70. We find a double well structure with a barrier that grows with increasing system size. We thus obtain an upper estimate of the value of the transition temperature in the thermodynamic limit.

Membrane Electrostatic Precipitator, Hajrudin Pasic, M. Khairul Alam, David J. Bayless

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A membrane is used as a collection substrate in an electrostatic precipitator (ESP). Possible material choices include fibers in the form of woven mats, screens made from stainless steel wires or fiber reinforced polymer composite membranes. The membranes have a tensile bias applied during operation, and have impulse tensile force applied during a dust removal step. By combining a dry ESP membrane field with wet-film cleaning field, it may be possible to improve collection efficiencies both by reducing turbulence and eliminating re-entrainment losses due to rapping. Through implementation of new materials that resist hostile ESP environments, the invention enhances the …

Dynamic Characterization Of Aluminum Softball Bats, Danny V. Lee

Dissertations and Theses

On January 1, 2000, the Amateur Softball Association of America (ASA) imposed maximum bat performance limitations on commercial softball bats. The ASA adopted a testing standard defined by the American Society of Testing and Materials (ASTM) to determine the bat performance factor (BPF), a normalized coefficient of restitution that must be less than 1.2 for the bat to be eligible for ASA sanctioned events.

The ASTM standard requires that the softball strike the bat, which is free to rotate in the horizontal plane, at 26.8 mfs ± 0.3 mfs (88 ftfs ± 1 ftfs) with little or no spin. The …

The Need For Emphasis On Teaching The Content Of Certain Subject Areas And Teaching Concepts Related To Certain Packaging Industry Job Titles As Perceived By Packaging Professionals In Indiana And The Surrounding States, Marion D. Schafer

All-Inclusive List of Electronic Theses and Dissertations

The study investigates the opinions or packaging professionals about an appropriate curriculum for a Bachelor of Science degree program in packaging. The study was conducted by surveying packaging profossionals randomly seleclcd from the Central Indiana Institute of Packaging Professionals mailing list. This list was made up mostly of Indiana residents but included a few residents from the fhur surrounding slates. The study was initiated as a first step in the process of developing appropri.ite improvements to the curriculum for the Bachelor of Science degree in packaging al Indiana State University. Six packaging job titles and twenty-three su~jcct areas were chosen …

Oxygen Permeation Through Cobalt-Containing Perovskites: Surface Oxygen Exchange Vs. Lattice Oxygen Diffusion, Kevin Huang, John B. Goodenough

Faculty Publications

The oxygen permeation fluxes from p′_O2 to pⁿ_O2 (p′_O2>pⁿ_O2) across cobalt-containing perovskite ceramic membranes La_1−xSr_xCoO_3−δ and SrCo_0.8Fe_0.2O_3−δ were measured by gas chromatography as functions of oxygen chemical potential gradient, temperature, thickness, and catalytic activity on the surface. Power indexes 0.5>n>0 for uncatalyzed La_1−xSr_xCoO_3−δ and 1>n>0.5 for SrCo_0.8Fe_0.2O_3−δ were obtained when J_O2 vs. p′ⁿ_O2−p'′ⁿ_{O2 …}

Overview Of Fuzzy Logic, Mohamed Trabia

Mechanical Engineering Faculty Presentations

The presentation includes a brief introduction to fuzzy logic and fuzzy logic controllers. These concepts are illustrated by an example of an autonomous vehicle controller.

Comparison Of Two Distributed Fuzzy Logic Controllers For Flexible-Link Manipulators, Linda Z. Shi, Mohamed Trabia

Mechanical Engineering Faculty Presentations

The paper suggests that fuzzy logic controllers present a computationally efficient and robust alternative to conventional controllers. The paper presents two possible structures for the distributed fuzzy logic controller of a single-link flexible manipulator. A linear quadratic regulator method is used to prove the effectiveness of fuzzy logic controllers.

Design Of Fuzzy Logic Controllers For Optimal Performance, Mohamed Trabia

Mechanical Engineering Faculty Presentations

While fuzzy logic controllers are generally robust, the performance of a system whose behavior is not well understood, or that has a large number of coupled inputs and outputs, may be less than optimal. In this paper, nonlinear programming techniques are used to improve the performance of a fuzzy logic controller for navigating an autonomous vehicle.

A Neural Network-Based Vision System For Automated Separation Of Onion From Clod Using Mechanical Harvester, Demian Morquin

Theses and Dissertations - UTB/UTPA

A neural network classifier for separating clods from onions during harvesting has been developed. The separator consists of a multi-layer feedforward network that maps textural features computed from gray-scale images of onions and clods into the correct object. Texture features were computed from co-occurrence matrices that specify the spatial relationship of pixel values in an image. The textural features selected for this application consist of homogeneity, contrast, variance, and energy. The network was trained using the back-propagation algorithm. Based on the textural features classification, the effect of changing the network configuration on separation effectiveness was investigated. Factors including network topology …

An Electronically Tunable Resonator For Noise Control, Charles Birdsong, Clark J. Radcliffe

Mechanical Engineering

Many engineering systems create unwanted noise that can be reduced by the careful application of engineering noise controls. When this noise travels down tubes and pipes, a tuned resonator can be used to muffle noise escaping from the tube. The classical examples are automobile exhaust and ventilation system noise. In these cases where a narrow frequency band of noise exists, a traditional engineering control consists of adding a tuned Helmholtz resonator to reduce unwanted tonal noise by reflecting it back to the source (Temkin, 1981). As long as the frequency of the unwanted noise falls within the tuned resonator frequency …

A New Portable, Pc Based, Usb Powered Dynamic Signal Analyzer, Charles Birdsong, George Ma, James Nieters, Justin Tang, Caine Yu

Mechanical Engineering

A new USB powered portable 4-channel real time Dynamic Signal Analyzer and its automotive applications are described. The design and architecture lend themselves to real time NVH measurements and analysis in the field, in-vehicle or on production lines. Built-in signal conditioning provides for direct sensor power while the embedded DSP provides for signal processing on-board. Performance and implementation of FFT, digital filters and order analyses are presented.

The Importance Of Site Surveys In Florida's Pv Buildings Program, Florida Solar Energy Center, Kevin Lynn

FSEC Energy Research Center®

One of the goals of the Florida PV Buildings Program is to ensure that only quality utility-interactive PV systems are installed in the state. One important component of the Program is the site survey. The purpose of the site survey is to inspect the potential location for PV system before beginning construction, ensuring it is a sensible place to install it. The purpose of this paper is to introduce the method used by this Program and to present some examples that will demonstrate why it is important.

Apr 2001, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Camp Creek Swap Meet Public Relations Get Fordson Running

A Comparative Analysis Of Studies On Heat Transfer And Fluid Flow In Microchannels, Choondal B. Sobhan, Suresh V. Garimella

CTRC Research Publications

The extremely high rates of heat transfer obtained by employing microchannels makes them an attractive alternative to conventional methods of heat dissipation, especially in applications related to the cooling of microelectronics. A compilation and analysis of the results from investigations on fluid flow and heat transfer in micro- and mini-channels and microtubes in the literature is presented in this review, with a special emphasis on quantitative experimental results and theoretical predictions. Anomalies and deviations from the behavior expected for conventional channels, both in terms of the frictional and heat transfer characteristics, are discussed.

Hide Glue Applicator, Chris Campo, Benjamin Carrasco, Elias Saliba

Mechanical Engineering

This study investigates the challenges inherent in applying hide glue in the crafting of violin and other stringed instruments. Hide glue, derived from animal collagen and protein, is essential for creating durable bonds that allow for necessary adjustments during fabrication. However, its meticulous heating and maintenance requirements pose logistical obstacles for luthiers lacking viable alternatives. To tackle this issue comprehensively, our project comprises several key components.

Initially, we conducted an in-depth analysis of the hide glue application process, delineating procedural steps and techniques to establish our design criteria and constraints. This foundational understanding formed the basis for further exploration. Additionally, …

Modeling Nonlinear Behavior In A Piezoelectric Actuator, Hanz Richter, Eduardo A. Misawa, D. A. Lucca, H. Lu

Mechanical Engineering Faculty Publications

A piezoelectric tube actuator is employed as a sample positioning device in Nanocut, a cutting instrument conceived to study the mechanics of nanometric cutting. Extension of functionality of the instrument as a nanometric machine tool motivates the search for an accurate model of the actuator for implementing feedback control. A simple nonlinear model describing longitudinal expansion of the piezoelectric tube actuator is presented in this paper. The model derivation is based on a non-formal analogy with nonlinear viscoelastic materials under uniaxial extension, for which the responses to a step input are similar to the piezoelectric tube. Suitability of the …

Study Of Automotive Hydromount Mechanism, Min Lu

Dissertations

The hydromount mechanism is studied. It was determined that the dynamic characteristics of the hydromounts are related to the rubber static stiffness, rubber damping coefficient, volumetric stiffness, and effectiveness of the oscillating fluid in the inertia track. At high frequencies the motion of the fluid in the inertia track diminishes so that its effect is negligible and may be ignored. It is also concluded that the rubber damping has a minimal effect on the hydromount dynamic properties and may be neglected. The maximum loss angle, which corresponds to the maximum damping coefficient of the hydromount, occurs near the inertia track …

A Substructuring Technique With Application To Spot Weld Placement Design, Yang Wang

Mechanical & Aerospace Engineering Theses & Dissertations

It is quite common in the industry to use various interface methods, such as welding, fasteners, bolts, adhesive bonding, etc., to join substructures together. The quality of the assembled structure is directly related to the type of the interface methods used in the manufacturing process. Thus, it is important to include the interface conditions as part of design variables in any design process. To this end, this work develops a reanalysis method that can efficiently analyze structures with variations on the interface conditions. This reanalysis method is based upon a new two-step substructuring technique. The first step performs substructural level …

Elastic Properties, Strength And Damage Tolerance Of Pultruded Composites, Mrinal Chandra Saha

Mechanical & Aerospace Engineering Theses & Dissertations

Pultruded composites are candidate materials for civil engineering infrastructural applications due their higher corrosion resistance and lower life cycle cost. Efficient use of materials like structural members requires thorough understanding of the mechanism that affects their response. The present investigation addresses the modeling and characterization of E-glass fiber/polyester resin matrix pultruded composites in the form of sheets of various thicknesses.

The elastic constants were measured using static, vibration and ultrasonic methods. Two types of piezoelectric crystals were used in ultrasonic measurements. Finally, the feasibility of using a single specimen, in the form of a circular disk, was shown in measuring …

Spice-Based Heat Transport Model For Non-Intrusive Thermal Diagnostic Applications, Michael Stelzer

Electrical & Computer Engineering Theses & Dissertations

Nondestructive material testing and diagnostics play an important role in reliability analysis, component wear-out testing, life-cycle estimates, and safety inspections. Of the several techniques available for nondestructive inspections, thermal analysis has been chosen to be the focus of this thesis research. An equivalence between the system of equations for the heat flow problem, and the variables of circuit theory suggests that an electrical model can be constructed to represent the actual thermal system. This electrical model is constructed based upon a finite difference discretization of the heat flow equation. Using these associations a basic one-dimensional electrical model has been constructed …

Development And Testing Of A Cfd-Based Optimization System For Axially Symmetric Rocket Nozzles, John-Paul Shebalin

Mechanical & Aerospace Engineering Theses & Dissertations

A software system has been developed to optimize rocket nozzle shapes for maximizing their performance. It has been established in the literature that one can use computer-based optimization with the parabolized Navier-Stokes equations to optimize the dimensions of low Reynolds number rocket nozzles-micronozzles. The Nozzle Optimization System described herein uses the full Navier-Stokes equations to optimize any axially symmetric rocket nozzle for which a converged solution can be obtained.

Four nozzles are optimized using this system-conical and contoured micronozzles and conical and contoured Space Transportation System(STS)-class nozzles. The optimum cone angle (O_cone) for the conical micronozzle was …