Mechanical Engineering Commons^™

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase I, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells and buffered chemical polishing produce good performance. The objective of the proposed research is to maximize the performance of the niobium cavities through studying multipacting, studying the effect of chemical etching on the surface roughness, and redesigning the cavities.

The US Congress has recently authorized exploring an alternative way to deal with spent nuclear fuel: Accelerator Transmuting of Waste (ATW). In this approach, a particle accelerator produces protons that react with …

On Modular Design Of Field Robotic Systems, Shane Farritor, Steven Dubowsky

Department of Mechanical and Materials Engineering: Faculty Publications

Robots are needed to perform important field tasks such as hazardous material clean-up, nuclear site inspection, and space exploration. Unfortunately their use is not widespread due to their long development times and high costs. To make them practical, a modular design approach is proposed. Prefabricated modules are rapidly assembled to give a low-cost system for a specific task. This paper described the modular design problem for field robots and the application of a hierarchical selection process to solve this problem. Theoretical analysis and an example case study are presented. The theoretical analysis of the modular design problem revealed the large …

Fpc Residential Monitoring Project: New Technology Development Radiant Barrier Pilot Project, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

The FPC Monitoring project has evaluated radiant barrier systems (RBS) as a new potential DSM program. The objective was to examine how the retrofit of attic radiant barriers can be expected to alter FPC residential space conditioning loads. An RBS consists of a layer of aluminum foil fastened to roof decking or roof trusses to block radiant heat transfer between the hot roof surface and the attic below. The radiant barrier can significantly lower summer heat transfer to the attic insulation and to the cooling duct system. Both of these mechanisms have strong potential impacts on cooling energy use as …

Nebraska Summary 354: Agco Dt200 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1790: 9300 T 24 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1797: Case Ih Stx 325/New Holland Tj 325 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1796: Case Ih Stx 275/New Holland Tj 275 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1794: White 8710 Also Agco Allis 9775 (Cummins Engine) Also Agco Dt200, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 1780a: White 8785, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1792: Massey Ferguson 2210 Diesel 15-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 389: Fendt 920 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 390: Fendt 924 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 391: Fendt 926 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

To Research, Analyse And Install An Optimised Maintenance Management System For A Medium Sized Manufacturing Company: A Textile Company Case Study, Christopher O'Donoghue

Theses

Modern manufacturing is continually striving to ensure that products are made to higher levels of quality with faster lead times and at the lowest possible costs. Manufacturing production has never been more reliant on machines and automated processes than it is today. This thesis investigates the management philosophies that are in existence, which cater specifically for maintenance and maintenance related issues. Management philosophies such as Reliability Centred Maintenance (RCM), Total Productive Maintenance (TPM), Profit Centred Maintenance (PCM), asset management (AM), Predictive Maintenance (PdM), Condition Based Maintenance (CBM) and World Class Maintenance (WCM) have increased company profits by drastically reducing maintenance …

Robust Adaptive Critic Based Neurocontrollers For Missiles With Model Uncertainties, Zhongwu Huang, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A Lyapunov theory-based controller is proposed in this paper for robustness against model uncertainties in the control of a missile. The controller design consists of two parts; in the first phase, an optimal nonlinear controller is designed with neural networks for tracking. This is based on the adaptive critic method that consists of one neural network called the supervisor or critic and a second network called an action network or a controller. Each network is trained through the output of the other network and equations related to optimal control. When their outputs are mutually consistent, the controller network output is …

Detection And Classification Of Impact-Induced Damage In Composite Plates Using Neural Networks, Rohit Dua, Steve Eugene Watkins, Donald C. Wunsch, K. Chandrashekhara, Farhad Akhavan

Electrical and Computer Engineering Faculty Research & Creative Works

Artificial neutral networks (ANN) can be used as an online health monitoring systems (involving damage assessment, fatigue monitoring and delamination detection) for composite structures owing to their inherent fast computing speeds, parallel processing and ability to learn and adapt to the experimental data. The amount of impact-induced strain on a composite structure can be found using strain sensors attached to composite structures. Prior work has shown that strain-based ANN can characterize impact energy on composite plates and that strain signatures can be associated with damage types and severity. This paper reports the extension of this approach for damage classification using …

Amplitude Modulated Droplet Formation In High Precision Solder Droplet Printing, Qingbin Liu, M. Orme, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

There are many methods used at present to apply solder to wafers, ceramics, laminate and flex circuit boards, and other substrates. Among these, high-precision solder droplet printing technology, which is noncontact, data driven, flexible and environmentally friendly, is a key enabling technology. This technology selectively deposits solder droplets only where required, and therefore needs no mask or secondary resist removal, uses materials more efficiently and creates less waste than other methods. Currently, continuous droplet formation from capillary streams is mainly achieved by application of the well-known Rayleigh instability in which a sinusoidal disturbance is applied to the stream, resulting in …

Robust State Dependent Riccati Equation Based Guidance Laws, S. N. Balakrishnan, Ming Xin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A robust state dependent Riccati equation based guidance/control is investigated in this study. In order to have a better design tool in terms of required interceptor accelerations, the target intercept geometry is formulated in a set of polar coordinates. With this formulation, we formulate a cost function with state dependent weights. In this study, we investigate the effects of such cost functions on the levels of interceptor accelerations. We also synthesize a neural network based extra controller to achieve the robustness in the presence of the target acceleration. In this manner, we will not need target acceleration estimation explicitly in …

An Optimal Control Based Treatment Strategy For Parturient Paresis Using Neural Networks, Radhakant Padhi, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An optimal online feedback treatment strategy is developed for the parturient paresis of cows, based on nonlinear optimal control theory. A limitation in the development of an existing mathematical model for calcium homeostasis is addressed and the model is extended to incorporate control inputs. An optimal feedback controller is synthesized for the nonlinear system using neural networks. Though the main aim of this paper is to solve the biomedical control problem, the methodology presented in this paper is a general computational tool, which can be applied to solve a fairly general class nonlinear optimal control problems.

Nebraska Summary 355: Agco Dt225 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1791: John Deere 9400t Also 9420t 24 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1789: John Deere 9200 24 & 12 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1796: Case Ih Stx 275/New Holland Tj 275 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 1797: Case Ih Stx 325/New Holland Tj 325 Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Tractor Test 1781: White 8510, Agco Dt160, Agco Allis 9755, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Tractor Test 1795: White 8810, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 1793: Massey Ferguson 2220 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

Nebraska Summary 388: Fendt 918 Vario Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA

The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data.

EXPLANATION OF THE TEST PROCEDURES

Purpose

The purpose of …

A Numerical Study Of Automotive Gas Tank Filler Pipe Two Phase Flow, R. Banerjee, Kakkattukuzhy M. Isaac, L. Oliver, W. Breig

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Automotive refueling is gaining greater importance because fuel vapors released during refueling are believed to increase ozone levels in urban areas. As a step towards On-Board Refueling Vapor Recovery (ORVR) designs, vapor generation and transport during refueling needs to be understood to develop recovery techniques. The objective of the present study is to understand the fluid flow inside the automotive gas tank filler pipe using commercially available Computational Fluid Dynamics (CFD) software. This effort is expected to yield detailed flow field information, including air entrainment. The phenomena of well-back, the process of fuel flooding the filler pipe and flowing backwards …

Re-Examination Of The Crypto-Steady Pressure-Exchanger (Virtual Turbomachine), T. Scott, David W. Riggins

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A crypto-steady pressure-exchanger (rotating center body ejecting fluid in a supersonic flow field) is investigated based on fundamental fluid dynamic principles. The results are then compared to computational fluid dynamic (CFD) simulations of a simplified device. On the basis of this comparison the device studied is correctly classified as an unsteady ejector instead of a type of turbomachinery. Entropy gains (total pressure losses) associated with the complex fluid-fluid and fluid-center body interactions are shown to be greater than total pressure gains due to work addition. Compared to a steady ejector, the virtual turbomachine shows increased entrainment (mixing) of the main …