Mechanical Engineering Commons^™

Mechanical Properties Of The Tendinous Equine Interosseus Muscle Are Affected By In Vivo Transducer Implantation, M. O. Jansen, H. C. Schamhardt, Antonie J. Van Den Bogert, W. Hartman

Mechanical Engineering Faculty Publications

Liquid metal strain gauges (LMSGs) were implanted in the tendinous interosseous muscle, also called suspensory ligament (SL), in the forelimbs of 6 ponies in order to quantify in vivo strains and forces. Kinematics and ground reaction forces were recorded simultaneously with LMSG signals at the walk and the trot prior to implantation, and 3 and 4 days thereafter. The ponies were euthanised and tensile and failure tests were performed on the instrumented tendons and on the tendons of the contra lateral limb, which were instrumented post mortem. The origo–insertional (OI) strain of the SL was computed from pre- and post-operative …

Remote Freedom, Dominic M. Florin

Undergraduate Honors Capstone Projects

Increasing mobility is a key to ensuring that a disabled child feels accepted and as normal as possible. The object of Remote Freedom is to provide an inexpensive design that will modify a toy vehicle so that it can run remotely. The case that we designed for was a child with cerebral palsy. Originally the toy vehicle on the market needed major modifications both for the safety of the child and the addition of the remote control The main components that were added were a safety harness, a roll bar and motors to control steering and speed.

It was discovered …

Research And Design Of A High L/D Aircraft, Blake Ashby, Gregory Nielson

Undergraduate Honors Capstone Projects

This senior design team, consisting of Blake Ashby, Shelly Barlow, Greg Nielson, Deryl Snyder, and Chris Wright, designed, built, and flew an airplane that met the requirements of the Cessna/ONR Student Design/Build/Fly Competition sponsored by AIAA. This radio-controlled airplane was designed to fly the most laps around a course in seven minutes using only 2.5 pounds of NiCad batteries. A total of three senior design teams from Utah State University designed separate airplanes. Though all three teams designed, built, and tested complete airplanes, each emphasized a different aspect of a successful entry. This team emphasized theoretical and numerical analysis in …

Dual Adaptive Recumbent Trike, Jason V. Eastman

Undergraduate Honors Capstone Projects

The DART team's objective was to develop a tandem recumbent tricycle that would be economical, easy to build, and adaptable. This would involve designing, building and testing the tricycle.

Hydrogen On-Orbit Storage And Supply: A Spacecraft Bus Design, Roy Gladden

Undergraduate Honors Capstone Projects

Spacecraft designers have two options when developing spacecraft for a particular mission. The bus, which is the primary structure and support system for the spacecraft, can be designed from an existing layout or a new design may be developed to meet specific mission needs. In recent years, the trend in small satellite design has been to employ a previously designed spacecraft bus in order to reduce cost and development time. However, these structures sometimes provide greater capability than is required for smaller, simple missions at a higher price. Therefore, it may be preferable to custom design a bus to meet …

Design Of The Guidance, Navigation, And Control Subsystem For The Proposed Firebird Spacecraft, Erin Robinson

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Firebird spacecraft is a space mission to gather scientific and physical data on the effects of atmospheric deceleration, commonly called aerobraking. The objective of the Firebird mission is to measure specified aerobraking parameters over a range of reentry velocities to provide a database sufficient to construct and validate mathematical models of such aerobraking mission maneuvers. The Firebird senior design team designed the first spacecraft in the mission series to look at aerobraking at an altitude of 160 kilometers above the surface of the Earth. This paper looks specifically at the design of the subsystem that provides the guidance, navigation, …

Nebraska Tractor Test Museum Committee Minutes April 14, 1998, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Treasurer's Report Preparation for Dedication Fund Raising Issues

Ole Miss Engineer 1998

Ole Miss Engineer

No abstract provided.

Degree Of Manufacturer Readiness For Skill-Based Pay Programs, Michael R. Willett

Graduate Research Papers

The purpose of this study is to determine the degree of readiness of manufacturing companies in Black Hawk County, Iowa, to adopt a skill-based pay plan. Readiness, or change orientation, will be determined by comparing current characteristics of companies in this sample to those characteristics of American companies that have already implemented successful skill-based pay plans.

Analysis And Testing Of Plates With Piezoelectric Sensors And Actuators, Jeffrey S. Bevan

Mechanical & Aerospace Engineering Faculty Publications

Piezoelectric material inherently possesses coupling between electrostatics and structural dynamics. Utilizing linear piezoelectric theory results in an intrinsically coupled pair of piezoelectric constitutive equations. One equation describes the direct piezoelectric effect where strains produce an electric field and the other describes the converse effect where an applied electrical field produces strain. The purpose of this study is to compare finite element analysis and experiments of a thin plate with bonded piezoelectric material. Since an isotropic plate in combination with a thin piezoelectric layer constitutes a special case of a laminated composite, the classical laminated plate theory is used in the …

Thin-Layer Prestressed Composite Ferroelectric Driver And Sensor Characterization With Application To Separation Flow Control, Karla M. Mossi

Mechanical & Aerospace Engineering Theses & Dissertations

Experiments were conducted in two different stages--general piezoelectric actuator characterization and flow separation control applications. The characterization of the piezoelectric devices was performed in several stages, due to the many variables that affect performance. The first stage of the characterization consisted of tests conducted on 13 different THUNDER^TM (thin-layer composite unimorph ferroelectric driver and sensor) configurations. These configurations consisted of a combination of 1, 3, 5, 7, and 9 layers of 25μ thick aluminum as backing material, with and without a top layer of 25μ aluminum. All of these configurations used the same piezoelectric ceramic wafer (PZT-5A) with dimensions …

Building Lms Adaptive Filters With Register-Based Fpgas, Li Ding

Electrical & Computer Engineering Theses & Dissertations

In this thesis, an 8-bit least mean squares (LMS) adaptive digital filter with 16 coefficients is implemented on a single FPGA, using the MaxPlus+2 design environment. The system is constructed as a hierarchical structure, using four different levels of design hierarchy. Subdesigns at each level of the hierarchy project are complied, fitted and simulated to test and verify their functional correctness. The complete system is tested and verified by checking the MaxPlus+2 simulator results against fixed-point integer arithmetic simulations written in Matlab. The resulting adaptive filter is subsequently mapped to the Alters FLEX I OK20TC144-3 device, resulting in a 14,500 …

Inversion And Analysis Of Remotely Sensed Atmospheric Water Vapor Measurements At 940nm, Jack Cutler Larsen

Mechanical & Aerospace Engineering Theses & Dissertations

The understanding and acceptance of remotely sensed atmospheric data depends strongly on the steps taken to characterize experiment error and validate observations through comparisons to other independent measurements. A formal error analysis of the Stratospheric Aerosol and Gas Experiment II (SAGE II) water vapor operational inversion algorithm is performed and compared to previous results. Random measurement errors were characterized by segmented least-squares profile fitting of the slant path absorption which found the error to be uncorrelated in the stratosphere with estimated variances significantly smaller than expected from 18-30 km. Estimates of null space error were developed from radiosonde hygrometers in …

Reduction Of Thermal Deflection And Random Response Of Composite Structures With Embedded Shape Memory Alloy At Elevated Temperature, Zhiwei Zhong

Mechanical & Aerospace Engineering Theses & Dissertations

A feasibility study on the reduction of thermal deflection and random response of the composite structures using shape memory alloys (SMA) at elevated temperatures is presented in this dissertation. The characteristics of SMA are introduced and the structural problems, static and dynamic, of SMA fiber reinforced composites are investigated. The stress-strain relations are developed for a composite lamina with embedded SMA fibers. The finite element system equations including shape memory effect are derived. A consistent two-step solution procedure is developed for solving the static and dynamic problems of composite structures with embedded SMA fibers subjected to combined acoustic and thermal …

Material Evaluation By Pulsed Diode Laser Optoacoustics, Xiaodong Xu

Electrical & Computer Engineering Theses & Dissertations

Pulsed diode laser optoacoustic diagnostics were carried out to characterize solid sample materials. The apparatus developed is compact, portable, cost-effective and therefore very promising for both industrial as well as laboratory applications. To our knowledge, this is the first time that optoacoustic characterization and measurement have been performed with a diode laser. The method was successfully applied to measure the thickness of a multilayer structure non-intrusively. Internal cracks of the material were detected by this technique.

A theory for optoacoustic signal generation, propagation and detection is given. A numerical analysis technique is developed to solve for the expected signal. In …

Ir-Hot Gas Heat Source For Automated Tow Placement, Ray Walton Grenoble

Mechanical & Aerospace Engineering Theses & Dissertations

A series of five experiments on the NASA Langley automated tow placement robot revealed stagnation of gas flow in the nip region. Since the torches could not heat effectively in the nip region, the roller temperature was the dominant influence on interlaminar bond strength. The roller temperatures required for high bond strength caused resin and fiber on the panel top surface to adhere to the compaction roller. Resin and fiber was pulled from the panel surface and wrapped around the roller, which was a severe processing problem. A supplemental radiant heat source was designed to permit reductions in roller temperature. …

System Identification And Control Of Cavity Noise Reduction, Chien-Hsun Kuo

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation first presents indirect closed-loop system identification through residual whitening, then identifies the cavity noise system and applies controllers to reduce the noise. High speed air flow over the cavity produces a complex oscillatory flow-field and induces pressure oscillations within the cavity. The existence of cavities induces large pressure fluctuations which generate undesirable and loud noise. This may have an adverse effect on the objects, such as reducing the stability and performance of overall system, or damaging the sensitive instruments within the cavity.

System identification is the process of building mathematical models of dynamical systems based on the available …

Nebraska Tractor Test Useumcommittee Minutes March 10, 1998, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Hitchcock Foundation Big Red Collectors Dedication of Museum

Diophantinized Fractional Representations For Nonlinear Elastomeric Media, Joe Padovan, Jerzy T. Sawicki

Mechanical Engineering Faculty Publications

This paper explores the use of diophantinized fractional fits for the nonlinear constitutive representation of elastomeric media. These are caste in terms of either the principal stretches or the strain invariants. Both polynomial and rational forms are considered. To construct the requisite complete and physically admissible basis space, the diophantinized set of fractional powers is bound by the curvature properties of the experimental data set. This set is then employed in conjunction with a remezed least square scheme to obtain an optimal fit. To verify the scheme a sample application case is presented.

Determination Of The Asymmetry Parameter And Scattering Coefficient Of Turbid Media From Spatially Resolved Reflectance Measurments, Matthew R. Jones, Yukio Yamada

Faculty Publications

We present a technique for determining the asymmetry parameter and scattering coefficient of turbid media from spatially resolved reflectance measurements. This technique will contribute to the development of medical applications in which it is necessary to predict the distribution and propagation of light in tissue. Based on Monte Carlo simulations, we derived correlations which relate the reduced scattering coefficient and the asymmetry parameter to the relative reflectance curve. Initial estimates of the optical properties are obtained from these correlations. Final values are obtained by adjusting the optical parameters and repeating the Monte Carlo simulations until the simulated reflectance pattern matches …

Comments On Response Errors Of Non-Proportionally Lightly Damped Structures, W. Gawronski, Jerzy T. Sawicki

Mechanical Engineering Faculty Publications

Letters to the editor authors reply

Tractor Test Museum Committee February 10, 1998, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Heating Issues Handouts for visitors Big Red Club

Three-Dimensional Dynamic Analysis Of Wheelchair Propulsion, Mary M. Rodgers, Srinivas Tummarakota, Junghsen Lieh

Mechanical and Materials Engineering Faculty Publications

A three-dimensional (3-D) inverse dynamic model of wheelchair propulsion was developed using the Newton-Euler method based on body coordinate systems. With this model, the arm was assumed to be three rigid segments (hand, forearm, and upper arm) connected by the wrist, elbow, and shoulder joints. A symbolic method was adopted to generate the equations of motion. The model was used to compute the joint forces and moments based on the inputs obtained from a 3-D motion analysis system, which included an instrumented wheelchair, video cameras, and a data acquisition system. The linear displacements of markers placed on the joints were …

Determination Of Bumper Styling And Engineering Parameters To Reduce Pedestrian Leg Injuries, Peter J. Schuster, Bradley Staines

Mechanical Engineering

The European Commission is proposing legislation aimed at reducing the severity of injuries sustained by pedestrians in the event of an impact with the front-end of a motor vehicle. One aspect of this proposed legislation is reducing the pedestrian's leg injuries due to contact with the bumper and frontal surfaces of a vehicle, assessed using a 'pedestrian leg impact device,' or 'leg-form.'

This proposed legislation presents the challenge of designing a bumper system which achieves the required performance in the leg-form impact-without sacrificing the bumper's primary function of vehicle protection during low-speed impacts. The first step in meeting this challenge …

Numerical Study Of Three-Dimensional Free Convection From Semi-Enclosed Geometry And Discontinuous Heat Sources, Aklilu T.G. Giorges

Dissertations

Three-dimensional natural convection from three-by-three array of isoflux heat sources mounted on one vertical wall of semi-enclosed region has been numerically investigated. Detailed thermal information of this important engineering configuration is currently not available. The major objective of this study was to obtain this needed thermal and velocity information.

The semi-enclosed geometry can be viewed as a thin rectangular region with four closed and two open sides. The open surfaces are located at the top and adjacent side. For the fluid air, Pr = 0.71, the study covered a heat flux based Rayleigh number (Ra) range of (10² ≤ …

Kinematic Analysis Of A Swash-Plate Mechanism Using Transformation Matrices, David Edgar Evans

Theses

The swash-plate mechanism is used to transfer rotational motion into translational motion and vice versa. Using transformation matrices to describe each joint, the displacements of the swash-plate mechanism were analyzed. The general transformation matrix model for the plane joint, not previously developed using transformation matrices, was presented. The solution was tested using a computer program. Examples of three different swash-plate angles; 10, 45, and 25' were considered. The solution was found to agree with previous solutions while offering a more complete description of the mechanism. Future work in this area could include a complete static, velocity, and/or dynamic analysis of …

Optimal Synthesis Of A Planar Four-Bar Function Generator Based On Imderect Measure Of Structural Error, Robert Ellis

Theses

A novel technique for optimal synthesis of a planar four-bar function generator is presented. An indirect measure of structural error is used to formulate an objective function which, along with its derivatives, is straightforward to evaluate and results in an elegant and robust algorithm. Lagrange multipliers are used to incorporate the loop closure constraint into the objective function.

In this thesis, the formulation of the objective function and the minimization algorithm are described, examples are presented, and the virtues and shortcomings of the algorithm are discussed.

Parameter Optimization For Curl Distortion In Building Parts Using 3-D Laser Stereolithography, Laurel A. Hanesian

Theses

The curl distortions in rapid prototyping using 3-D laser stereo lithography occur as the top layers shrink after being drawn and attaching to the bottom layers. The amount of curl is dependent upon the how much shrinkage the layer has finished prior to adhesion. It is also dependent on how deep the cure of the top layer amounts to as it adheres into the bottom layer. This thesis investigated the effect of build parameters on the distortions associated with the diagnostic 'Letter-H' shaped test part. The same parameters were also considered in a time optimization study, using calculated, predicted results …

Dynamic Friction Measurement, Modeling, And Compensation For Precise Motion Control, Simon Cohn

Theses

In this thesis, measurements of dynamic friction in a hydrodynamic journal bearing were performed for varying sinusoidal velocity excitations, loads, and lubricants. The results indicate that the friction data displays a negative slope in the mixed region of friction vs. velocity (f-v) curves, and also shows that the dynamic friction is not just a function of current velocity, but also a function of velocity history (hysteresis). These results are in agreement with previous experimental investigations by other investigators in lubricated friction.

Secondly, a dynamic friction model is fully explored and partially extended to provide quantitative agreement to measured friction values. …

Nebraska Tractor Test Museum Committee Minutes January 20th, 1998, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Roof Repair Big Red Convention Dedication Ceremony